Skip to contentSkip to conversation

typo ?

LARTC Mihai RUSU 2 participants 2 messages Apr 4, 2002

lore
Share & tools
lore

Mihai RUSU

author
#0 lore raw

Hi

While reading the HOWTO (pdf downloaded and printed last night) I have noticed a little strange thing. In the 9.2.1 chapter, explaining the pfifo_fast qdisc, it is shown a TOS field mapping table and also it appears a command line version:

"The last column shows the result of the default priomap. On the commandline, the default priomap looks like this:
1, 2, 2, 2, 1, 2, 0, 0 , 1, 1, 1, 1, 1, 1, 1, 1

This means that priority 4, for example, gets mapped to band number 1. The priomap also allows you to list higher priorities (> 7) which do not correspond to TOS mappings, but which are set by other means."

The numbers on the command line version are 16, thus I presume its a one to one corespondation to the table, only that it is completly different. I dont see any explanation why it is like that. Shouldnt that be:
1,2,1,1,2,2,2,2,0,0,0,0,1,1,1,1 ?

Thanks

----------------------------
Mihai RUSU

Disclaimer: Any views or opinions presented within this e-mail are solely those of the author and do not necessarily represent those of any company, unless otherwise specifically stated.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

"Mihai RUSU" wrote

Quoted 20 lines

Hi

While reading the HOWTO (pdf downloaded and printed last night) I have noticed a little strange thing. In the 9.2.1 chapter, explaining the pfifo_fast qdisc, it is shown a TOS field mapping table and also it appears a command line version:

"The last column shows the result of the default priomap. On the commandline, the default priomap looks like this:
1, 2, 2, 2, 1, 2, 0, 0 , 1, 1, 1, 1, 1, 1, 1, 1

This means that priority 4, for example, gets mapped to band number 1. The priomap also allows you to list higher priorities (> 7) which do not correspond to TOS mappings, but which are set by other means."

The numbers on the command line version are 16, thus I presume its a one to one corespondation to the table, only that it is completly different. I dont see any explanation why it is like that. Shouldnt that be:
1,2,1,1,2,2,2,2,0,0,0,0,1,1,1,1 ?

Quoted 5 lines

Thanks

----------------------------
Mihai RUSU

nope. Try the following:

# tc qdisc del dev eth0 root
# tc qdisc add dev eth0 root handle 1: prio
# tc -s qdisc ls dev eth0
qdisc prio 1: bands 3 priomap  1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
 Sent 455336 bytes 1237 pkts (dropped 0, overlimits 0)

which is the default priomap on the commandline. The one you mention is the priomap in the kernel for pfifo_fast.

I usually set the priomap manually to get the latter priomap. example:
tc qdisc add dev eth0 root handle 1: prio bands 4 priomap 2 3 2 2 3 3 3 3 1 1 1 1 2 2 2 2
(which is the kernels default + 1, here I use the 0 band for very important traffic which goes above the TOS-field.)

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/