Skip to contentSkip to conversation

split traffic

LARTC Emil Terziev 5 participants 6 messages May 28, 2002 – Oct 15, 2002

lore
Share & tools
lore
#0 lore raw

Hi ,
I need to limit traffic from my LAN
(172.16.1.x/24)for every IP but to have 2 type speed.

I have BG_Traffic (couple LANs 212.50.16.0/24,
217.9.231.0/24, 195.24.39.0/24)

and I have not_BG_Traffic (rest of Internet world). I want for example
IP 172.16.1.10 to have 10K for BG_Traffic and 25K for not_BG_Traffic.
IP 172.16.1.11 to have 6K for BG_Traffic and 64K for not_BG_Traffic.
IP 172.16.1.12 to have 8K for BG_Traffic and 10K for not_BG_Traffic.

Can help me? I’m newer with tc&iproute and this ii
very difficult for me

Regards
Emil Terziev

__________________________________________________
Do You Yahoo!?
Yahoo! - Official partner of 2002 FIFA World Cup
http://fifaworldcup.yahoo.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 16 lines · Emil Terziev

Hi ,
I need to limit traffic from my LAN
(172.16.1.x/24)for every IP but to have 2 type speed.

   I have BG_Traffic (couple LANs 212.50.16.0/24,

217.9.231.0/24, 195.24.39.0/24)

and I have not_BG_Traffic (rest of Internet world). I want for example
IP 172.16.1.10 to have 10K for BG_Traffic and 25K for not_BG_Traffic.
IP 172.16.1.11 to have 6K for BG_Traffic and 64K for not_BG_Traffic.
IP 172.16.1.12 to have 8K for BG_Traffic and 10K for not_BG_Traffic.

Quoted 2 lines

Can help me? I’m newer with tc&iproute and this ii
very difficult for me

It's not so difficult once you understand how it works. And yes; it's possible what you want to do.
Have you read the Lartc HOWTO ? And I have some scripts and more info on www.docum.org about shaping. Try to read the docs and to understand the scripts. If you have more questions, just post them and we will try to answer them.

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Emil Terziev

I have the next network:

Users LAN Servers LAN
(10.0.0.0/24 (mail and web [200.30.57.32/24]
web surf main activity) homologated ip's)

|                                |
|                                | 
|                                |
|                                | 
|________________________________| 
                  |
eth1:1 10.0.0.138 |      eth1 200.30.57.33
                  |
          {Linux Firewall. kernel 2.4.18}
                  |
     eth2         |      eth0 200.30.53.22/30
    192.168.1.2/30|
                  |
  _______________/ \______________
 |                                |
 |                                |
{adsl router}               {Cisco router}  200.30.53.21/30
 |192.168.1.1                     |
 |(phone line)                    |(DS0)
 |                                |
 |                                |
{   --------   Internet -------    }

A network with two links to internet: a DS0 and an adsl.

I want that servers with homologated ip's go via the DS0, and end users, with 10.0.0.0 addresses go via adsl. Both links through the same firewall.

Also, end users must have Nat, and servers dont. For this i use:
iptables -t nat -A POSTROUTING -s 10.0.0.0/24 -o eth2 -j MASQUERADE

The default gateway in the firewall is the cisco router, my question is:
How can I make to force packets from 10.0.0.0 go via eth2(192.168.1.2) ?

I imagine something like:

ip route add 192.168.1.1/30 via 192.168.1.2 table 1 ip rule add from 10.0.0.0/24 table 1

But doesn't work. What'd be the correct way to do it?

Omar

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Emil Terziev

Omar,

It looks like you want to set a different default route for the 10.0.0.0/24 network. This can be done as follows:

# ip route add default via 192.168.1.1 table 1
# ip rule add from 10.0.0.0/24 table 1

Your iptables line should work just dandily.....

I think what you are getting confused about is why your existing route doesn't work. I'd suggest thinking about the name of the chain in the nat
table: POSTROUTING!!

Unless routing table 1 contains something else, there's no explicit instruction for the outbound packets from 10.0.0.0/24. Add a default route to that table, and you should have a better solution.

Check out "Multiple Connections to the Internet" in Chapter 7 in my guide (which is still in the process of being written):

http://plorf.net/linux-ip/

Good luck,

-Martin

: I have the next network:
:
:
: Users LAN Servers LAN
: (10.0.0.0/24 (mail and web [200.30.57.32/24]
: web surf main activity) homologated ip's)

 : |                                |
 : |                                | 
 : |                                |
 : |                                | 
 : |________________________________| 
 :                   |
 : eth1:1 10.0.0.138 |      eth1 200.30.57.33
 :                   |
 :           {Linux Firewall. kernel 2.4.18}
 :                   |
 :      eth2         |      eth0 200.30.53.22/30
 :     192.168.1.2/30|
 :                   |
 :   _______________/ \______________
 :  |                                |
 :  |                                |
 : {adsl router}               {Cisco router}  200.30.53.21/30
 :  |192.168.1.1                     |
 :  |(phone line)                    |(DS0)
 :  |                                |
 :  |                                |

: { -------- Internet ------- }
:
:
:
:
: A network with two links to internet: a DS0 and an adsl.
:
: I want that servers with homologated ip's go via the DS0, and end users, : with 10.0.0.0 addresses go via adsl. Both links through the same : firewall.
:
: Also, end users must have Nat, and servers dont. For this i use:
: iptables -t nat -A POSTROUTING -s 10.0.0.0/24 -o eth2 -j MASQUERADE :
: The default gateway in the firewall is the cisco router, my question is:
: How can I make to force packets from 10.0.0.0 go via eth2(192.168.1.2) ? :
:
: I imagine something like:
:
: ip route add 192.168.1.1/30 via 192.168.1.2 table 1
: ip rule add from 10.0.0.0/24 table 1
:
:
: But doesn't work. What'd be the correct way to do it?
:
:
: Omar
:
:
:
:
:
:
:
: _______________________________________________
: LARTC mailing list / [email protected]
: http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
:

Signature · 6 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to Emil Terziev
Quoted 31 lines
# ip route add default via 192.168.1.1 table 1
# ip rule add from 10.0.0.0/24 table 1

: I have the next network:
:
:
: Users LAN Servers LAN
: (10.0.0.0/24 (mail and web [200.30.57.32/24]
: web surf main activity) homologated ip's)

 : |                                |
 : |                                | 
 : |                                |
 : |                                | 
 : |________________________________| 
 :                   |
 : eth1:1 10.0.0.138 |      eth1 200.30.57.33
 :                   |
 :           {Linux Firewall. kernel 2.4.18}
 :                   |
 :      eth2         |      eth0 200.30.53.22/30
 :     192.168.1.2/30|
 :                   |
 :   _______________/ \______________
 :  |                                |
 :  |                                |
 : {adsl router}               {Cisco router}  200.30.53.21/30
 :  |192.168.1.1                     |
 :  |(phone line)                    |(DS0)
 :  |                                |
 :  |                                |
Quoted 4 lines

: { -------- Internet ------- }
:
:
:

Thanks, Martin. It worked(since last week) perfect.

Now I have the above network working. Users from class 10.0.0.0/24 go out through the adsl router, and the servers via the DS0.

NowI want to put a transparent proxy with squid, but if I configure it with just:

iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128

http requests are processed via the DS0(this is because of the default gw , I suppose), and I want them to go out via the adsl

My question is, how can I make that http requests go via the adsl with a transparent proxy with this network configuration?

I've thought it must be the OUTPUT chain. But with what rule?

Hope you can orient me.

Thanks,

Omar

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#5 lore raw
In reply to Emil Terziev
Quoted 9 lines · Omar Armas

Now I have the above network working. Users from class 10.0.0.0/24 go out through the adsl router, and the servers via the DS0.

NowI want to put a transparent proxy with squid, but if I configure it with just:

iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128

Quoted 7 lines

http requests are processed via the DS0(this is because of the default gw , I suppose), and I want them to go out via the adsl

My question is, how can I make that http requests go via the adsl with a transparent proxy with this network configuration?

I've thought it must be the OUTPUT chain. But with what rule?

None. :-)

Do not think of it as packet mangling, but as a squid configuration.

To be exact, there are two config values which should be especially interesting for you:
tcp_outgoing_address 192.168.4.55
udp_outgoing_address 192.168.4.55
...where 192.168.4.55 is the IP of your ADSL connection interface. :-)

HTH, HAND,
QNeX

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/