Skip to contentSkip to conversation

How to make Linux server transparent to internal machines?

LARTC Neil Aggarwal 5 participants 5 messages May 31, 2002 – Jun 3, 2002

lore
Share & tools
lore
#0 lore raw

Hello:

I have a block of static IP addresses on which I want to run several Windows machines.

Since I want to have a firewall, I was thinking of using 1 IP address for a linux server that will act as a firewall for the entire setup.

So, here is a diagram:

[Internet] -- [Linux Server] -- switch -- [Internal machines]

The linux server and the internal machines all have static IP addresses which are public to the Internet.

How can I set-up routing so the Linux server is "transparent" to the other machines?

Thanks,
Neil.

--
Neil Aggarwal
JAMM Consulting, Inc. (972) 612-6056, http://www.JAMMConsulting.com
Custom Internet Development Websites, Ecommerce, Java, databases

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

what you want to do is setup a bridgeing firewall
http://bridge.sourceforge.net/
----- Original Message -----
From: "Neil Aggarwal" <[email protected]>
To: <[email protected]>
Sent: Friday, May 31, 2002 2:55 PM
Subject: [LARTC] How to make Linux server transparent to internal machines?

Quoted 22 lines

Hello:

I have a block of static IP addresses on which I want to run several Windows machines.

Since I want to have a firewall, I was thinking of using 1 IP address for a linux server that will act as a firewall for the entire setup.

So, here is a diagram:

[Internet] -- [Linux Server] -- switch -- [Internal machines]

The linux server and the internal machines all have static IP addresses which are public to the Internet.

How can I set-up routing so the Linux server is "transparent" to the other machines?

Thanks,
Neil.

Quoted 10 lines

--
Neil Aggarwal
JAMM Consulting, Inc. (972) 612-6056, http://www.JAMMConsulting.com
Custom Internet Development Websites, Ecommerce, Java, databases

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Neil Aggarwal
Quoted 11 lines · Neil Aggarwal

Hello:

I have a block of static IP addresses on which I want to run several Windows machines.

Since I want to have a firewall, I was thinking of using 1 IP address for a linux server that will act as a firewall for the entire setup.

So, here is a diagram:

Quoted 7 lines

[Internet] -- [Linux Server] -- switch -- [Internal machines]

The linux server and the internal machines all have static IP addresses which are public to the Internet.

How can I set-up routing so the Linux server is "transparent" to the other machines?

You can play with the routing on the Linux server. The default gw of the linux server points to the internet, but for each internal machine, you add an extra route to the right NIC. The internal machines have the ip-address of the LInux server as default gw. You can even give both NIC's of the Linux-server the same ip-address so you don't losse one.

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to Neil Aggarwal

Excellent articles in there...

You can also set-up a Proxy-ARP firewall. This is basically a router but there is no need to set up/modify a gateway setting in the internal machines, all traffic passes through the router transparently (as in the bridge, but now switching is done at IP level -- i.e. "true" routing).

The pros: it's easier to set-up than the bridge code. there's no need to patch kernel code and/or commandline tools

The cons: slightly lower throughput, slightly lower security... but easier ;-)

José Carlos
[email protected]

---- Mensaje original ----
De: Chris K Ellsworth
Fecha: Sat 6/1/02 0:02
Para: [email protected]
Asunto: Re: [LARTC] How to make Linux server transparent to internal machines?

what you want to do is setup a bridgeing firewall
http://bridge.sourceforge.net/

----- Original Message -----
From: "Neil Aggarwal" <[email protected]>
To: <[email protected]>
Sent: Friday, May 31, 2002 2:55 PM
Subject: [LARTC] How to make Linux server transparent to internal machines?

Quoted 22 lines

Hello:

I have a block of static IP addresses on which I want to run several Windows machines.

Since I want to have a firewall, I was thinking of using 1 IP address for a linux server that will act as a firewall for the entire setup.

So, here is a diagram:

[Internet] -- [Linux Server] -- switch -- [Internal machines]

The linux server and the internal machines all have static IP addresses which are public to the Internet.

How can I set-up routing so the Linux server is "transparent" to the other machines?

Thanks,
Neil.

Quoted 10 lines

--
Neil Aggarwal
JAMM Consulting, Inc. (972) 612-6056, http://www.JAMMConsulting.com
Custom Internet Development Websites, Ecommerce, Java, databases

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Neil Aggarwal
Quoted 6 lines

The pros: it's easier to set-up than the bridge code. there's no need to patch
kernel code and/or commandline tools

The cons: slightly lower throughput, slightly lower security... but easier ;-)

I'd like to know why you think using proxy-arp is lower security than bridging ...

Signature · 6 lines
Michael T. Babcock
CTO, FibreSpeed Ltd.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/