Skip to contentSkip to conversation

ADVANCED ROUTING USING IPROUTE2 -> Multiple Firewalls

LARTC Roni Reicher 2 participants 2 messages Jun 15, 2002

lore
Share & tools
lore
#0 lore raw

Hi William. Thanks a lot for your help.

Im having some trouble recompiling my kernel after a installed the patch.

Im running RH 7.3 with kernel 2.4.18-3.

The patch I installed is routes-2.4.16-6.diff. I got no errors installing it.

I added the multipath support, and recompiled it.

The make dep and the make bzImage went fine.

I got error during the make modules.

These are the errors:

Output.c: in function 'cipe_xmit'
Output.c:175 too few arguments to function 'ip_route_output' Make[3]: *** [output.o] error 1
Make[3]: leaving directory '/usr/src/linux-2.4.18-3/drivers/addon/cipe' Make[2]: *** [_modsubdir_cipe] error 2
Make[2]: leaving directory '/usr/src/linux-2.4.18-3/drivers/addon' Make[1]: *** [_modsubdir_addon] error 2
Make[1]: leaving directory '/usr/src/linux-2.4.18-3/drivers
Make: *** [_mod_drivers] error 2

After I got that error, a formatted and reinstalled redhat 7.3. Then I used the newer patch (routes-2.4.19-8.diff), and I got error installing, and of course I couldn't recompile it.

I formatted again to see if I were doing something wrong recompiling. But this time I didn't patch and recompile it. I got no errors...

Any ideas? Am I using the wrong patch?

Thanks a lot,

Ron

-----Mensagem original-----
De: William L. Thomson Jr. [mailto:[email protected]] Enviada em: quinta-feira, 13 de junho de 2002 14:43
Para: [email protected]
Assunto: Re: [LARTC] ADVANCED ROUTING USING IPROUTE2 -> Multiple Firewalls

You will need to recompile your kernel with multpath support. Also before you compile apply Julian's patches to the kernel.

http://www.linuxvirtualserver.org/~julian/#routes

Once that is done check out the Nano-HOWTO

http://www.linuxvirtualserver.org/~julian/nano.txt

That should get you on your way. The linux router will also have to perform NAT, more than likely DNAT, for things to work properly.

Quoted 12 lines · Roni Reicher

Hi guys. I really need some help.

This is my scenario:

Quoted 1 line

CLIENTS -> SWITCH -> W2K Server -> Linux -> Internet (with 2 ADSL

LINES)

Quoted 11 lines

My RedHat Linux 7.2 is just a firewall. Im running all the services (www, mail, etc.) on my W2K.

I tried to set up a load balance, but im getting the following

problem.

Quoted 193 lines

When I connect from the internet through my IP1 (ADSL 1) on any port that I redirect to W2K, I can connect perfectly to my W2K, but when I connect using my IP2 (ADSL2) I cant get to W2K.

And vice versa.

With the telnet server, which is running on the linux, I can connect using both IP's.

I guess the problem is when the W2K uses the other gw.

My W2K default gw is the linux.

This is my setup:

W2K IP -> 10.0.0.1

W2K IP2 -> 192.168.1.2

Linux eth0 -> xxx.xxx.xxx.170 (ADSL1)

Linux eth0 gw -> xxx.xxx.xxx.129

Linux eth1 -> 192.168.1.1

Linux eth2 -> yyy.yyy.yyy.205 (ADSL2)

Linux eth2 gw -> yyy.yyy.yyy.193

IPTABLES (just the basic).

$IPTABLES -A INPUT -i lo -j ACCEPT

$IPTABLES -A INPUT -p icmp -j ACCEPT

$IPTABLES -A FORWARD -o eth0 -j ACCEPT

$IPTABLES -A FORWARD -o eth2 -j ACCEPT

##################### SMTP SERVER #################

$IPTABLES -t nat -A PREROUTING -p tcp -d xxx.xxx.xxx.170 --dport 25

(quoted diff) +0 -2
-j DNAT --to-destination 192.168.1.2
 
 $IPTABLES -t nat -A PREROUTING -p tcp -d yyy.yyy.yyy.205  --dport 25
-j DNAT --to-destination 192.168.1.2

##################### HTTP SERVER ##################

$IPTABLES -t nat -A PREROUTING -p tcp -d xxx.xxx.xxx.170 --dport 80

(quoted diff) +0 -2
-j DNAT --to-destination 192.168.1.2
 
 $IPTABLES -t nat -A PREROUTING -p tcp -d yyy.yyy.yyy.205 --dport 80
-j DNAT --to-destination 192.168.1.2
 
 
 
 $IPTABLES -t nat -A POSTROUTING -s 192.168.1.0/24 -j MASQUERADE
 
 $IPTABLES -t nat -A POSTROUTING -s 10.0.0.0/24    -j MASQUERADE
 
 $IPTABLES -t nat -A POSTROUTING -o eth0           -j MASQUERADE
 
 $IPTABLES -t nat -A POSTROUTING -o eth2           -j MASQUERADE

And this is my load balancing script:

#### Variables ######

IP=/sbin/ip

IF1=eth0

IP1=xxx.xxx.xxx.170

P1=xxx.xxx.xxx.129

P1_NET=xxx.xxx.xxx.128/26

IF2=eth2

IP2=yyy.yyy.yyy.205

P2= yyy.yyy.yyy.193

P2_NET= yyy.yyy.yyy.192/26

echo 201 t1 >> /etc/iproute2/rt_tables

echo 202 t2 >> /etc/iproute2/rt_tables

$IP route add $P1_NET dev $IF1 src $IP1 table t1

$IP route add default via $P1 table t1

$IP route add $P2_NET dev $IF2 src $IP2 table t2

$IP route add default via $P2 table t2

$IP route add $P1_NET dev $IF1 src $IP1

$IP route add $P2_NET dev $IF2 src $IP2

$IP route add default via $P1

$IP rule add from $IP1 table t1

$IP rule add from $IP2 table t2

$IP route add default scope global nexthop via $P1 dev $IF1 weight 1 nexthop via $P2 dev $IF2 weight 1

I really need help.

I appreciate it,

Ron Reicher

[email protected]

Signature · 25 lines
Sincerely,
William L. Thomson Jr.
Obsidian-Studios, Inc.
439 Amber Way
Petaluma, Ca. 94952
Phone  707.766.9509
Fax    707.766.8989
http://www.obsidian-studios.com
-- 
Sincerely,
William L. Thomson Jr.
Support Group
Obsidian-Studios Inc.
439 Amber Way
Petaluma, Ca. 94952
Phone  707.766.9509
Fax    707.766.8989
http://www.obsidian-studios.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

Hello,

Quoted 9 lines · Roni Reicher

Output.c: in function 'cipe_xmit'
Output.c:175 too few arguments to function 'ip_route_output' Make[3]: *** [output.o] error 1
Make[3]: leaving directory '/usr/src/linux-2.4.18-3/drivers/addon/cipe' Make[2]: *** [_modsubdir_cipe] error 2
Make[2]: leaving directory '/usr/src/linux-2.4.18-3/drivers/addon' Make[1]: *** [_modsubdir_addon] error 2
Make[1]: leaving directory '/usr/src/linux-2.4.18-3/drivers
Make: *** [_mod_drivers] error 2

IIRC, Roberto Nibali provided patch for cipe to use it
together with the "routes" patch, it is on the web page:

cipe-1.5.2-routes-1.diff

Quoted 3 lines

After I got that error, a formatted and reinstalled redhat 7.3. Then I used the newer patch (routes-2.4.19-8.diff), and I got error installing, and of course I couldn't recompile it.

	You can use routes-2.4.19-8.diff after 2.4.19pre8. It does

not have the problem to change the interface of the routing functions, so such problems with applying extra patches to code out of the plain kernel should not exist.

Quoted 1 line

Ron

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/