Skip to contentSkip to conversation

priomap table

LARTC bert hubert 2 participants 2 messages Jun 29, 2002 – Jun 30, 2002

lore
Share & tools
lore
#0 lore raw
Quoted 33 lines · Vik Heyndrickx

Hi guys,

In the current LARTC Howto, at 9.2.1.1. "Parameters & usage", there is the following table

<txttable>
TOS Bits Means Linux Priority Band
------------------------------------------------------------

0x0     0     Normal Service           0 Best Effort     1
0x2     1     Minimize Monetary Cost   1 Filler          2
0x4     2     Maximize Reliability     0 Best Effort     1
0x6     3     mmc+mr                   0 Best Effort     1
0x8     4     Maximize Throughput      2 Bulk            2
0xa     5     mmc+mt                   2 Bulk            2
0xc     6     mr+mt                    2 Bulk            2
0xe     7     mmc+mr+mt                2 Bulk            2
0x10    8     Minimize Delay           6 Interactive     0
0x12    9     mmc+md                   6 Interactive     0
0x14    10    mr+md                    6 Interactive     0
0x16    11    mmc+mr+md                6 Interactive     0
0x18    12    mt+md                    4 Int. Bulk       1
0x1a    13    mmc+mt+md                4 Int. Bulk       1
0x1c    14    mr+mt+md                 4 Int. Bulk       1
0x1e    15    mmc+mr+mt+md             4 Int. Bulk       1

</txttable>

And then
<quote>
The last column shows the result of the default priomap. On the commandline, the default priomap looks like this:
1, 2, 2, 2, 1, 2, 0, 0, 1, 1, 1, 1, 1, 1, 1, 1 </quote>

Quoted 3 lines

Now, why are this "band column" and priomap list different? Is there a relationship between them, or is it just a mistake, or did I miss something (also a good possibility)?

There is an additional level of indirection in there I think. I really really went over this with a fine comb when I wrote it. Perhaps something changed? Would the commandline default priomap make sense?

Regards,

bert

Quoted 6 lines

Thanks,

--
Vik

Signature · 6 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
http://www.tk                              the dot in .tk
http://lartc.org           Linux Advanced Routing & Traffic Control HOWTO
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 8 lines

-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of bert hubert
Sent: Saturday, June 29, 2002 6:13 PM
To: Vik Heyndrickx
Cc: [email protected]
Subject: [LARTC] Re: priomap table

Quoted 8 lines
Quoted 2 lines

Now, why are this "band column" and priomap list different? Is there a relationship between them, or is it just a mistake, or did I

miss something

Quoted 1 line

(also a good possibility)?

There is an additional level of indirection in there I think. I really really went over this with a fine comb when I wrote it. Perhaps something changed? Would the commandline default priomap make sense?

The default priomap doesn't make sense if put as-is in the last column. Anyway, the default priomap with a current kernel is still the same as in the documentation and it appears that "Minimize Delay" pings are indeed put into prio/pfifo_fast band 0, just like the table suggested. The extra layer of indirection is the fourth column of the table, which originates from I don't know where.

I was experimenting with a four band prio qdisc. Now that I understand this, I think I've got to go back to the drawing board. I wondered why my "Minimize Delay" pings were classified into the second band qdisc.

--
Vik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/