Skip to contentSkip to conversation

Splitting locally generated traffic based on destination port

LARTC Arthur Donkers 3 participants 4 messages Aug 31, 2002

lore
Share & tools
lore
#0 lore raw

Hi All,

I have a Linux box (2.4.19, iptables 1.2.6a) that has two Ethernet interfaces. Eth0 is connected to a cisco which is connected to the Internet via a leasedline. Eth1 is connected to an ADSL connection. Both interfaces have a fixed IP address, and the default route points over the ADSL connection (because this is used for browsing, ftp and such).

However, the Eth0 has the 'official' IP address and should be used for send e-mail and some ssh traffic.

I already defined a policy to return incoming traffic over the interface it was received, so both interface can be contacted via the Internet.

My question now is how to define a policy so specific traffic, generated locally by sendmail and ssh, uses eth0 as its interface in stead of eth1 which is used for the default route ?

I already mark outgoing traffic in the mangle table thus

iptables -A OUTPUT -t mangle -p tcp --dport 25 -j MARK --set-mark 1

I have to SNAT outgoing traffic as well:

iptables -A POSTROUTING -t nat -m mark --mark 1 -j SNAT --to-source <eth0>

I have added a table mail.out to /etc/iproute2/rt_tables and defined rules like this:

ip rule add fwmark 1 table mail.out
ip route add default via <gw on eth0 network> dev eth0 src <eth0>

And when I do this:

telnet <mailhost> 25

I indeed see a SYN packet coming out of eth0 to <mailhost>, and a SYN/ACK packet comes back. The problem is that it appears that the Linux box does not see this SYN/ACK packet and resends the SYN packet after a few seconds, which again is answered by a SYN/ACK and this goes on a few times. No other packet filters are active on the Linux box (yet).

So how do I get this setup to work ? Am I heading for the wrong direction with the policy or is there something else missing ?

thnx in advance,

Arthur Donkers

--

/* Disclaimer :   you hire my skills, not my opinions, those are mine !    */
/* email : [email protected]    Security    'Me ? I'm not me ! I'm just a   */
/* phone : (+31) 50 549 2701   is not a     computer simulation of me'     */
/* URL http://www.reseau.nl   dirty word      Red Dwarf, First Episode     */

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Re: [LARTC] Splitting locally generated traffic based on destination

Quoted 8 lines · Arthur Donkers

I have added a table mail.out to /etc/iproute2/rt_tables and defined rules like this:

ip rule add fwmark 1 table mail.out
ip route add default via <gw on eth0 network> dev eth0 src <eth0>

And when I do this:

Quoted 7 lines

telnet <mailhost> 25

I indeed see a SYN packet coming out of eth0 to <mailhost>, and a SYN/ACK packet comes back. The problem is that it appears that the Linux box does not see this SYN/ACK packet and resends the SYN packet after a few seconds, which again is answered by a SYN/ACK and this goes on a few times. No other packet filters are active on the Linux box (yet).

Try:

echo "0" > /proc/sys/net/ipv4/conf/eth0/rp_filter

If it works, to make it permanent, include this line in your /etc/sysctl.conf file:

net/ipv4/conf/eth0/rp_filter = 0

Signature · 8 lines
Miernik              _____________________________________
                    /   /
tel.: +48603070983 /   /  mailto:[email protected]
__________________/___/  ICQ UIN: 4004001

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Arthur Donkers
Quoted 15 lines · Arthur Donkers

My question now is how to define a policy so specific traffic, generated locally by sendmail and ssh, uses eth0 as its interface in stead of eth1 which is used for the default route ?

I already mark outgoing traffic in the mangle table thus iptables -A OUTPUT -t mangle -p tcp --dport 25 -j MARK --set-mark 1 I have to SNAT outgoing traffic as well:
iptables -A POSTROUTING -t nat -m mark --mark 1 -j SNAT --to-source <eth0> I have added a table mail.out to /etc/iproute2/rt_tables and defined rules like this:
ip rule add fwmark 1 table mail.out
ip route add default via <gw on eth0 network> dev eth0 src <eth0>

Quoted 8 lines

And when I do this:
telnet <mailhost> 25

I indeed see a SYN packet coming out of eth0 to <mailhost>, and a SYN/ACK packet comes back. The problem is that it appears that the Linux box does not see this SYN/ACK packet and resends the SYN packet after a few seconds, which again is answered by a SYN/ACK and this goes on a few times. No other packet filters are active on the Linux box (yet).

Hello Arthur,

I´m not a professional in routing, but I think I´ve read something about the routing mechanism:

Packet ---> Table PREROUTING -+-> Table FORWARD -+-> Table POSTROUTING

                               |                   |    (and then out)
                               +-> Table INCOMING  |
                                                   |

Table OUTGOING -+

The problem is, that the routing decision is done AFTER processing the forward table, but BEFORE the postrouting table (NAT). So it is possible to modify the packets in POSTROUTING that way, that they will go out via device A, but have the ip of the other device B.
If the "answer" packet comes in at A (but are addressed to B), the address will be checked and device A drops (/does not listen to) them. ("Hey, that packet is not for me !").

Possible unclean variant to fix that would be to put device A in the so called "promisc" (promiscueing ?) mode, where all packets are processed.

Clean variant is _not_ to do NAT by the filter. Make the _routing_ decision depending on the filter. And NAT is done afterwards based on the routing.

Hope I told not too much wrong,
Sebastian

-=> Sebastian Bleikamp
-=> EMail: <[email protected]>
-=> Phone: +49-172-6545394

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Arthur Donkers
Quoted 18 lines · Miernik
Quoted 8 lines · Arthur Donkers

I have added a table mail.out to /etc/iproute2/rt_tables and defined rules like this:

ip rule add fwmark 1 table mail.out
ip route add default via <gw on eth0 network> dev eth0 src <eth0>

And when I do this:

Quoted 7 lines

telnet <mailhost> 25

I indeed see a SYN packet coming out of eth0 to <mailhost>, and a SYN/ACK packet comes back. The problem is that it appears that the Linux box does not see this SYN/ACK packet and resends the SYN packet after a few seconds, which again is answered by a SYN/ACK and this goes on a few times. No other packet filters are active on the Linux box (yet).

Quoted 8 lines

Try:

echo "0" > /proc/sys/net/ipv4/conf/eth0/rp_filter

If it works, to make it permanent, include this line in your /etc/sysctl.conf file:

net/ipv4/conf/eth0/rp_filter = 0

thanks ! this works !

grtz,

Arthur

Quoted 6 lines
Signature · 5 lines
-- 
Miernik              _____________________________________
                    /   /
tel.: +48603070983 /   /  mailto:[email protected]
__________________/___/  ICQ UIN: 4004001

--

/* Disclaimer :   you hire my skills, not my opinions, those are mine !    */
/* email : [email protected]    Security    'Me ? I'm not me ! I'm just a   */
/* phone : (+31) 50 549 2701   is not a     computer simulation of me'     */
/* URL http://www.reseau.nl   dirty word      Red Dwarf, First Episode     */

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/