Skip to contentSkip to conversation

How to use private IP on my DMZ network

LARTC Roselyn Calleja 2 participants 2 messages Oct 4, 2002

lore
Share & tools
lore
#0 lore raw

Hi everyone,

I have problems with my DMZ network. I'm using Linux with three interface (eth0, eth1,eth2). eth0 is connected to my dsl modem, eth1 is for my DMZ network where it contains all my websites, eth2 is my private network. I'm using iptables. Below is my diagram:

                                                          |-----------|       
      DSL (Internet) eth0 ------ |Firewall | -------  eth2 (Private Network)
                                                          |-----|-----|       
                                                                    | 
                                                                    |

eth1 (DMZ network)

my current set-up:

eth0 : 203.164.168.30

            gw:  203.164.168.29
            mask: 255.255.255.252

eth1: 203.164.168.161 (also the gateway of the network)

            mask:255.255.255.248 

website 1: 203.164.168.163
website 2: 203.164.168.164
website 3: 203.164.168.165

I want to set-up my network like this:

eth0 : same IP
same gateway
same netmask

eth1 : 10.10.10.1

            gw: 10.10.10.1

website1: 10.10.10.5
website2:10.10.10.6
website3:10.10.10.7
website1 public address is 203.164.168.163
website2 public address is 203.164.168.164
website3 public address is 203.164.168.165

So my iptables looks like this:

iptables --table nat -A PREROUTING -p tcp -d 203.164.168.163 --dport 80 -j DNAT --to-destination 10.10.10.5 iptables --table nat -A PREROUTING -p tcp -d 203.164.168.164 --dport 80 -j DNAT --to-destination 10.10.10.6 iptables --table nat -A PREROUTING -p tcp -d 203.164.168.165 --dport 80 -j DNAT --to-destination 10.10.10.7

So what i mean is that any request for 203.164.168.163 to 165 would pass through my firewall then with my iptables set as such, it would be forwarded to my webserver.

Does anybody knows how to work this thing out? Is it possible? Please reply.

Thanks!

Rose

#1 lore raw
Quoted 15 lines · Roselyn Calleja

I have problems with my DMZ network. I'm using Linux with three interface (eth0, eth1,eth2). eth0 is connected to my dsl modem, eth1 is for my DMZ network where it contains all my websites, eth2 is my private network. I'm using iptables. Below is my diagram:

eth0 : 203.164.168.30

            gw:  203.164.168.29
            mask: 255.255.255.252

eth1: 203.164.168.161 (also the gateway of the network)

            mask:255.255.255.248

website 1: 203.164.168.163
website 2: 203.164.168.164
website 3: 203.164.168.165

I want to set-up my network like this:

eth1 : 10.10.10.1

Quoted 8 lines
            gw: 10.10.10.1

website1: 10.10.10.5
website2:10.10.10.6
website3:10.10.10.7
website1 public address is 203.164.168.163
website2 public address is 203.164.168.164
website3 public address is 203.164.168.165
Does anybody knows how to work this thing out? Is it possible? Please reply.

I'm very new to this list, but IMHO this list is for iproute2 and traffic conditioner. Your Problem looks like normal routing problems.

1. Why using privat IP's if you have public IP's ?

2. Is the first setup decribed above curently working ?

if not, you may need proxy-arp or modify your arp-cache if yes, ip-aliasing will be your friend and then you can use DNAT.

3. if you setup private ips for security reasons you better use proxy services.

and so on ....

P.S. can some listinsider give me some rules for answering
this kind of questions DROP, REJECT, FORWARD, ACCEPT ? :)

greets,
Tami

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/