Skip to contentSkip to conversation

ssh versus scp

LARTC Sebastian 'spax' Pape 6 participants 8 messages Nov 25, 2002 – Nov 26, 2002

lore
Share & tools
lore
#0 lore raw

hi!

I'd like to priorize ssh traffic, but of course I don't like scp to get priorized, too. In the "actual script" of the howto priorization is done with this:

| # TOS Minimum Delay (ssh, NOT scp) in 1:10:
| tc filter add dev $DEV parent 1:0 protocol ip prio 10 u32 \
|      match ip tos 0x10 0xff  flowid 1:10

I'm not sure if I got all of it, but it seems to me, that there is no port match - it seems to me that this rule matches all packets with a Minimize-Delay 16 (0x10) TOS value.

I watched some packets with tcpdump and it also seems that scp packets all have the Maximize-Throughput 8 (0x08) TOS value, but all "pure ssh" packets have Normal-Service 0 (0x00). It's no problem to match these packets with iptables (just drop me a note if you want to have the iptables syntax). But the question I have is:

Are these TOS-values standard for ssh and scp or do all ssh/scp-clients use the values they like? I searched the net, but haven't found anything usefull, yet.

best regards

Sebastian

Signature · 8 lines
Sebastian 'spax' Pape          | A diplomat is someone who can tell you to go
mailto: [email protected]   | to hell in such a way that you will look
gpg: http://p-a-p-e.de/gpg.asc | forward to the trip.
         --- Do you want to know more? http://www.p-a-p-e.de/ ---

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

Hi,

You are out of luck here. There is no distinction between ssh and scp at IP, TCP or the application layer for that matter. Basically scp is a wrapper which uses ssh as the transfer method...

Ramin

Quoted 20 lines · Sebastian 'spax' Pape

hi!

I'd like to priorize ssh traffic, but of course I don't like scp to get priorized, too. In the "actual script" of the howto priorization is done with this:

| # TOS Minimum Delay (ssh, NOT scp) in 1:10:
| tc filter add dev $DEV parent 1:0 protocol ip prio 10 u32 \
|      match ip tos 0x10 0xff  flowid 1:10

I'm not sure if I got all of it, but it seems to me, that there is no port match - it seems to me that this rule matches all packets with a Minimize-Delay 16 (0x10) TOS value.

I watched some packets with tcpdump and it also seems that scp packets all have the Maximize-Throughput 8 (0x08) TOS value, but all "pure ssh" packets have Normal-Service 0 (0x00). It's no problem to match these packets with iptables (just drop me a note if you want to have the iptables syntax). But the question I have is:

Quoted 17 lines

Are these TOS-values standard for ssh and scp or do all ssh/scp-clients use the values they like? I searched the net, but haven't found anything usefull, yet.

best regards

Sebastian

Signature · 8 lines
Sebastian 'spax' Pape          | A diplomat is someone who can tell you to go
mailto: [email protected]   | to hell in such a way that you will look
gpg: http://p-a-p-e.de/gpg.asc | forward to the trip.
         --- Do you want to know more? http://www.p-a-p-e.de/ ---

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Sebastian 'spax' Pape

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 5 lines · Sebastian 'spax' Pape

I watched some packets with tcpdump and it also seems that scp packets all have the Maximize-Throughput 8 (0x08) TOS value, but all "pure ssh" packets have Normal-Service 0 (0x00). It's no problem to match these packets with iptables (just drop me a note if you want to have the iptables syntax). But the question I have is:

could you please tell me how you match ssh and not scp with iptables?

- --
Regards,
Robert
- ----------------
Robert Penz
robert.penz AT outertech.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.6 (GNU/Linux)
Comment: For info see http://www.gnupg.org

iD8DBQE94pmo8tTsQqJDUBMRAkIuAJ44N5sKyIchhtR4Lz9AdwilasreqwCeLwNn Cmu0zd+LZhgKLnK88jOwlSY=
=ix/M
-----END PGP SIGNATURE-----

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Sebastian 'spax' Pape

For posterity:

Data gathered with the following tcpdump command:

# tcpdump  -nnqti eth0 port 22 and host y.y.y.y

ssh session:
<session setup snipped, no special ToS value; normal>

x.x.x.x.48101 > y.y.y.y.22: tcp 48 (DF) [tos 0x10] y.y.y.y.22 > x.x.x.x.48101: tcp 0 (DF) y.y.y.y.22 > x.x.x.x.48101: tcp 48 (DF) [tos 0x10] y.y.y.y.22 > x.x.x.x.48101: tcp 80 (DF) [tos 0x10] x.x.x.x.48101 > y.y.y.y.22: tcp 0 (DF) [tos 0x10]

scp session:
<session setup snipped, no special ToS value; normal>

y.y.y.y.22 > x.x.x.x.48103: tcp 48 (DF) x.x.x.x.48103 > y.y.y.y.22: tcp 64 (DF) [tos 0x8] y.y.y.y.22 > x.x.x.x.48103: tcp 48 (DF) [tos 0x8] x.x.x.x.48103 > y.y.y.y.22: tcp 0 (DF) [tos 0x8] y.y.y.y.22 > x.x.x.x.48103: tcp 48 (DF) [tos 0x8]

So, one *should* be able to do something like this:

# iptables -t filter -A FORWARD -m tos --tos 0x08 -j scpchain
# iptables -t filter -A FORWARD -m tos --tos 0x10 -j sshchain

http://iptables-tutorial.frozentux.net/iptables-tutorial.html

I haven't done it.....Good luck,

-Martin

Signature · 6 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to Sebastian 'spax' Pape

Hello,
It's nice but ...
When I make ssh connection, it has tos 0x10. It's Ok.
When I use ssh with any commands, than tos is 0x8. (e.i ssh user@host su) And little trick to end...
When I make ssh tunnel, it has tos 0x10 and so I can push data with minimum delay tos.

I think that there is only possibility to use bytecount patch.

Quoted 26 lines · Martin A. Brown

For posterity:

Data gathered with the following tcpdump command:

# tcpdump  -nnqti eth0 port 22 and host y.y.y.y

ssh session:
<session setup snipped, no special ToS value; normal>

x.x.x.x.48101 > y.y.y.y.22: tcp 48 (DF) [tos 0x10] y.y.y.y.22 > x.x.x.x.48101: tcp 0 (DF) y.y.y.y.22 > x.x.x.x.48101: tcp 48 (DF) [tos 0x10] y.y.y.y.22 > x.x.x.x.48101: tcp 80 (DF) [tos 0x10] x.x.x.x.48101 > y.y.y.y.22: tcp 0 (DF) [tos 0x10]

scp session:
<session setup snipped, no special ToS value; normal>

y.y.y.y.22 > x.x.x.x.48103: tcp 48 (DF) x.x.x.x.48103 > y.y.y.y.22: tcp 64 (DF) [tos 0x8] y.y.y.y.22 > x.x.x.x.48103: tcp 48 (DF) [tos 0x8] x.x.x.x.48103 > y.y.y.y.22: tcp 0 (DF) [tos 0x8] y.y.y.y.22 > x.x.x.x.48103: tcp 48 (DF) [tos 0x8]

So, one *should* be able to do something like this:

Quoted 8 lines
# iptables -t filter -A FORWARD -m tos --tos 0x08 -j scpchain
# iptables -t filter -A FORWARD -m tos --tos 0x10 -j sshchain

http://iptables-tutorial.frozentux.net/iptables-tutorial.html

I haven't done it.....Good luck,

-Martin

--
`)_|_(' PSIkappa
I k psi _at_ talker.sk

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#5 lore raw
In reply to Sebastian 'spax' Pape
Quoted 1 line · Robert Penz

could you please tell me how you match ssh and not scp with iptables?

I did almost the same as Martin suggested:

| So, one *should* be able to do something like this:
|
| # iptables -t filter -A FORWARD -m tos --tos 0x08 -j scpchain
| # iptables -t filter -A FORWARD -m tos --tos 0x10 -j sshchain

# (ssh)
# $IPTABLES -A PREROUTING -t mangle -p tcp --dport 22 \
# -m tos ! --tos Maximize-Throughput \
# -j MARK --set-mark 2

# (scp)
# $IPTABLES -A PREROUTING -t mangle -p tcp --dport 22 \
# -m tos --tos Maximize-Throughput \
# -j MARK --set-mark 8

it works for me but I'm not sure if it is in general correct.

greetings
Sebastian

Signature · 9 lines
Sebastian 'spax' Pape          | "Things should be as simple as possible, but
mailto: [email protected]   | not simpler." -- Albert Einstein
gpg: http://p-a-p-e.de/gpg.asc |
         --- Do you want to know more? http://www.p-a-p-e.de/ ---


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#6 lore raw
In reply to Sebastian 'spax' Pape

hi Martin,

I found almost the same except that my ssh-packets didn't have their TOS-value set.

Quoted 4 lines

So, one *should* be able to do something like this:

# iptables -t filter -A FORWARD -m tos --tos 0x08 -j scpchain
# iptables -t filter -A FORWARD -m tos --tos 0x10 -j sshchain

That's almost the same idea as in the "actual script" from the HOWTO. So it seems my ssh-client doesn't like to set tos-values :o

Quoted 1 line

http://iptables-tutorial.frozentux.net/iptables-tutorial.html

*bookmarked* ;)

greetings
Sebastian

Signature · 8 lines
Sebastian 'spax' Pape          | "Things should be as simple as possible, but
mailto: [email protected]   | not simpler." -- Albert Einstein
gpg: http://p-a-p-e.de/gpg.asc |
         --- Do you want to know more? http://www.p-a-p-e.de/ ---

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#7 lore raw
In reply to Sebastian 'spax' Pape

--On Monday, November 25, 2002 8:12 PM +0100 Sebastian 'spax' Pape

Quoted 3 lines · <[email protected]> wrote:

Are these TOS-values standard for ssh and scp or do all ssh/scp-clients use the values they like? I searched the net, but haven't found anything usefull, yet.

Good question. In general, is there a Linux API for setting TOS on a connection? Or for UDP? For example, what would be the "right" values for UDP game packets, which suffer if dropped or delayed?
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/