Skip to contentSkip to conversation

2 internal NIC's in the same network

LARTC virdzek, roman 2 participants 6 messages Nov 25, 2002 – Nov 27, 2002

lore
Share & tools
lore
#0 lore raw

hi,
i have two internal nics

at PC1

eth1 eth2
10.0.0.1 10.0.0.2

            |              |
            switch 
                 |
              pc2
              eth0
            10.0.0.3       

and when I ping from pc2 -> PC1:eth2, using tcpdump i see that PC1
send reply to (arp who has 10.0.0.2), 10.0.0.2 is at .....eth1.
why PC1 send back not proper HW address? how I can force PC1 to say that 10.0.0.2 is at eth2?

thanks in advance!

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Roman,

# echo 1 > /proc/sys/net/ipv4/conf/all/hidden
# echo 1 > /proc/sys/net/ipv4/conf/eth1/hidden
# echo 1 > /proc/sys/net/ipv4/conf/eth2/hidden

If you don't have support for hidden in your kernel, visit Julian's page:

http://www.linux-vs.org/~julian/
http://www.linux-vs.org/~julian/#hidden

This will prevent ethernet interfaces from responding for ARP for IPs active on other devices.

Good luck,

-Martin

: and when I ping from pc2 -> PC1:eth2,
: using tcpdump i see that PC1
: send reply to (arp who has 10.0.0.2),
: 10.0.0.2 is at .....eth1.
: why PC1 send back not proper HW address?
: how I can force PC1 to say that 10.0.0.2
: is at eth2?
:
:
:
: thanks in advance!
:
:
:
:
:
: _______________________________________________
: LARTC mailing list / [email protected]
: http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
:

Signature · 6 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to virdzek, roman

martin,
I apply this patch and set hidden =1,arp_filter =1 too,
at all nic's but nothing changed. eth1 always reply that ip 10.0.0.2 is at eth1...

It seems be so,that I can't forward packets over two different nic's which are in same network.

bye

Quoted 41 lines

Roman,

# echo 1 > /proc/sys/net/ipv4/conf/all/hidden
# echo 1 > /proc/sys/net/ipv4/conf/eth1/hidden
# echo 1 > /proc/sys/net/ipv4/conf/eth2/hidden

If you don't have support for hidden in your kernel, visit Julian's page:

http://www.linux-vs.org/~julian/
http://www.linux-vs.org/~julian/#hidden

This will prevent ethernet interfaces from responding for ARP for IPs active on other devices.

Good luck,

-Martin

: and when I ping from pc2 -> PC1:eth2,
: using tcpdump i see that PC1
: send reply to (arp who has 10.0.0.2),
: 10.0.0.2 is at .....eth1.
: why PC1 send back not proper HW address?
: how I can force PC1 to say that 10.0.0.2
: is at eth2?
:
:
:
: thanks in advance!
:
:
:
:
:
: _______________________________________________
: LARTC mailing list / [email protected]
: http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
:

Signature · 17 lines
Roman Virdzek - System & Network Engineering
____________________________________________

JARON INTERNET GmbH
Hanauer Landstrasse 196a
D-60314 Frankfurt am Main
Fon:+49-69-405866-36 ; Fax:+49-69-405866-29
Internet:  www.jaron.de ; www.popularix.de
____________________________________________

( Saving Private Ryan...
  Private Ryan exists. Overwrite? (Y/N) )


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to virdzek, roman

Roman,

: I apply this patch and set hidden =1,arp_filter =1 too, : at all nic's but nothing changed. eth1 always reply that : ip 10.0.0.2 is at eth1...
: It seems be so,that I can't forward packets over two different : nic's which are in same network.

Tarek was correct when he mentioned that you'll need to use policy routing in addition if both of the IPs you are using fall within the same network.

# ip rule add from 10.0.0.2 lookup 2
# ip rule add from 10.0.0.1 lookup 1
# ip route add 10.0.0.0/24 dev eth1 src 10.0.0.1
# ip route add 10.0.0.0/24 dev eth2 src 10.0.0.2

Turn on the ARP hiding functionality:

# echo 1 > /proc/sys/net/ipv4/conf/all/hidden

You'll need to do this *after* you have brought up the interfaces and set the hidden flags explicitly.

# echo 1 > /proc/sys/net/ipv4/conf/eth1/hidden
# echo 1 > /proc/sys/net/ipv4/conf/eth2/hidden

Good luck,

-Martin

: >Roman,
: >
: >
: >If you don't have support for hidden in your kernel, visit Julian's page:
: >
: > http://www.linux-vs.org/~julian/
: > http://www.linux-vs.org/~julian/#hidden
: >
: >This will prevent ethernet interfaces from responding for ARP for IPs : >active on other devices.
: >
: >Good luck,
: >
: >-Martin
: >
: > : and when I ping from pc2 -> PC1:eth2,
: > : using tcpdump i see that PC1
: > : send reply to (arp who has 10.0.0.2),
: > : 10.0.0.2 is at .....eth1.
: > : why PC1 send back not proper HW address?
: > : how I can force PC1 to say that 10.0.0.2
: > : is at eth2?
: > :
: > :
: > :
: > : thanks in advance!
: > :
: > :
: > :
: > :
: > :
: > : _______________________________________________
: > : LARTC mailing list / [email protected]
: > : http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
: > :
: >
: >
: >
:
:
:

Signature · 6 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to virdzek, roman

Sorry! Correction below:

-Martin

Tarek was correct when he mentioned that you'll need to use policy routing in addition if both of the IPs you are using fall within the same network.

 # ip rule add from 10.0.0.2 lookup 2
 # ip rule add from 10.0.0.1 lookup 1
 # ip route add 10.0.0.0/24 dev eth1 src 10.0.0.1 table 1
 # ip route add 10.0.0.0/24 dev eth2 src 10.0.0.2 table 2

Turn on the ARP hiding functionality:

 # echo 1 > /proc/sys/net/ipv4/conf/all/hidden

You'll need to do this *after* you have brought up the interfaces and set the hidden flags explicitly.

 # echo 1 > /proc/sys/net/ipv4/conf/eth1/hidden
 # echo 1 > /proc/sys/net/ipv4/conf/eth2/hidden
Signature · 6 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#5 lore raw
In reply to virdzek, roman

hi,
ok thanks, it seem to be working now.
why it will not working with:

ip rule add iif eth2 lookup 2
ip rule add iif eth1 lookup 1 ?

and another one question. i have turned on
log martians, and kernel still write to me:
martian source from ...........when I ping
eth1 | eth2 ...but back get proper arp reply.

thanks for reply
bye

Quoted 24 lines

Sorry! Correction below:

-Martin

Tarek was correct when he mentioned that you'll need to use policy routing in addition if both of the IPs you are using fall within the same network.

# ip rule add from 10.0.0.2 lookup 2
# ip rule add from 10.0.0.1 lookup 1
# ip route add 10.0.0.0/24 dev eth1 src 10.0.0.1 table 1
# ip route add 10.0.0.0/24 dev eth2 src 10.0.0.2 table 2

Turn on the ARP hiding functionality:

# echo 1 > /proc/sys/net/ipv4/conf/all/hidden

You'll need to do this *after* you have brought up the interfaces and set the hidden flags explicitly.

# echo 1 > /proc/sys/net/ipv4/conf/eth1/hidden
# echo 1 > /proc/sys/net/ipv4/conf/eth2/hidden
Signature · 16 lines
Roman Virdzek - System & Network Engineering
____________________________________________

JARON INTERNET GmbH
Hanauer Landstrasse 196a
D-60314 Frankfurt am Main
Fon:+49-69-405866-36 ; Fax:+49-69-405866-29
Internet:  www.jaron.de ; www.popularix.de
____________________________________________

( I drive way too fast to worry about cholesterol. )


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/