total bandwidth ocupied
Dear sir/madam,
I discover that bandwidth usage which is limited using htb is about 5 to 10% higher than the rate/ceil we set, if we monitor it using iptraf.
I become more confused since I saw, the grafic in HTB homepage are also show more bandwidth than the setting.
My question is:
* what is the exac value of this over bandwidth?
* how to make the bandwidth are limited exacly at "x" kbps?
Signature · 6 lines
Regards, Adi Nugroho _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 11 lines · Adi Nugroho
Dear sir/madam,
I discover that bandwidth usage which is limited using htb is about 5 to 10% higher than the rate/ceil we set, if we monitor it using iptraf.
I become more confused since I saw, the grafic in HTB homepage are also show more bandwidth than the setting.
My question is:
* what is the exac value of this over bandwidth?
* how to make the bandwidth are limited exacly at "x" kbps?
I did some "stream" tests with htb. I generated a lot of tcp traffic with tcp and recorded the shaped bandwidth. The result is allmost perfect. (results can be found on www.docum.org on the test pages).
But in a real world scenario, you also have bursts in the traffic. Maybe you allow bursts (you always have some minimal bursts) so the average bandwidth may be higher then the configured bandwith.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Adi Nugroho wrote:
| Dear sir/madam, | | I discover that bandwidth usage which is limited using htb is about 5 to 10% | higher than the rate/ceil we set, if we monitor it using iptraf. | | I become more confused since I saw, the grafic in HTB homepage are also show | more bandwidth than the setting. | | My question is: | * what is the exac value of this over bandwidth?
It depends of burst and cburst values that you (or tc) set. In Devik's user guide says: "Latest tc tool will compute and set the smallest possible burst when it is not specified". This means:
minimal_burst=max_rate*timer_resolution
So, for 2Mbit bandwidth on i386, minimal_burst=2Mbit*10ms kbit. This says the theory, but in real world I saw that this minimal_burst calculated by tc could be up to 64kbit. Am I missing something?
| * how to make the bandwidth are limited exacly at "x" kbps?
Set a lower value for ceil and a value for cburst thus:
ceil+cburst=limited_bandwidth
- --
Catalin Bucur mailto:[email protected]
NOC @ Genius Network SRL - Galati - Romania
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.6 (GNU/Linux)
Comment: For info see http://www.gnupg.org
iD8DBQE9/ggIpDe20wwI9oIRApcqAJ94Z53bvrGpAvCUVPO8mmI3eHIV2gCfcwXK pALs5TiT9dbZf42GNtVBHOc=JRkQ
-----END PGP SIGNATURE-----
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Pada hari Selasa, 17 Desember 2002 01:06, Catalin Bucur menulis:
Quoted 4 lines
| * how to make the bandwidth are limited exacly at "x" kbps?
Set a lower value for ceil and a value for cburst thus:
ceil+cburst=limited_bandwidth
Thank you very much.
This calculation is very helpfull.
Signature · 6 lines
Salam, Adi Nugroho _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/