Skip to contentSkip to conversation

Filter in HTB not working

LARTC Nestor S A Melo 4 participants 4 messages Dec 19, 2002 – Dec 20, 2002

lore
Share & tools
lore
#0 lore raw

I have a problem in setting up HTB.

It appears filters doesn't work at all, besides "tc filter show" show it as being correctly configured.

Class 1:10 never sent any traffic, but as iptables show below, it should be sending packets.

The HTB version I'm using is 3.3, with kernel 2.4.17.

The setup is as follows:
---------------------------------------------------------------
tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1 htb default 20 r2q 10

tc class add dev eth0 parent 1: classid 1:2 htb rate 256kbit

tc class add dev eth0 parent 1:2 classid 1:10 htb rate 26kbit ceil 128kbit prio
1
tc qdisc add dev eth0 parent 1:10 handle 10 sfq perturb 10
tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip sport 23 0xffff classid 1:10

tc class add dev eth0 parent 1:2 classid 1:20 htb rate 220kbit ceil 256kbit prio 2
tc qdisc add dev eth0 parent 1:20 handle 20 sfq perturb 10
---------------------------------------------------------------

The stats:
---------------------------------------------------------------
[root@NL1000 htb]# tc -s -d qdisc show
qdisc sfq 20: dev eth0 quantum 1514b limit 128p flows 128/1024 perturb 10sec
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)

qdisc sfq 10: dev eth0 quantum 1514b limit 128p flows 128/1024 perturb 10sec Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc htb 1: dev eth0 r2q 10 default 20 direct_packets_stat 0 ver 3.6 Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)

[root@NL1000 htb]# tc -s -d class show dev eth0
class htb 1:10 parent 1:2 leaf 10: prio 1 quantum 1000 rate 26Kbit ceil 128Kbit
burst 1632b/8 mpu 0b cburst 1762b/8 mpu 0b level 0
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 401969 ctokens: 88149

class htb 1:2 root rate 256Kbit ceil 256Kbit burst 1926b/8 mpu 0b cburst 1926b/8 mpu 0b level 7
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 46975 ctokens: 46975

class htb 1:20 parent 1:2 leaf 20: prio 2 quantum 2816 rate 220Kbit ceil 256Kbit burst 1880b/8 mpu 0b cburst 1926b/8 mpu 0b level 0
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)
lended: 94 borrowed: 0 giants: 0
tokens: 53324 ctokens: 46975

[root@NL1000 htb]# tc -s -d filter show dev eth0
filter parent 1: protocol ip pref 100 u32
filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt
0 flowid 1:10
match 00170000/ffff0000 at 20

[root@NL1000 htb]# iptables -t mangle -L -nvx Chain PREROUTING (policy ACCEPT 3590 packets, 557751 bytes)
pkts bytes target prot opt in out source
destination

       0        0 MARK       tcp  --  *      *       0.0.0.0/0            
0.0.0.0/0          tcp dpt:23 MARK set 0x6
     146    12954 MARK       tcp  --  *      *       0.0.0.0/0            

0.0.0.0/0 tcp spt:23 MARK set 0x6

Chain OUTPUT (policy ACCEPT 315 packets, 16936 bytes)
pkts bytes target prot opt in out source
destination
---------------------------------------------------------------

So, what is going wrong?

Thanks in advance,

Signature · 5 lines
_____________________
Nestor S A Melo
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

From what I see you are running a telnet daemon. If not it will never work. If you are doing this to shape telnet traffic from a telnet client then rather than sport it'll have to be dport.

Quoted 86 lines · Nestor S A Melo

I have a problem in setting up HTB.

It appears filters doesn't work at all, besides "tc filter show" show it as being correctly configured.

Class 1:10 never sent any traffic, but as iptables show below, it should be sending packets.

The HTB version I'm using is 3.3, with kernel 2.4.17.

The setup is as follows:
---------------------------------------------------------------
tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1 htb default 20 r2q 10

tc class add dev eth0 parent 1: classid 1:2 htb rate 256kbit

tc class add dev eth0 parent 1:2 classid 1:10 htb rate 26kbit ceil 128kbit prio
1
tc qdisc add dev eth0 parent 1:10 handle 10 sfq perturb 10
tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip sport 23 0xffff classid 1:10

tc class add dev eth0 parent 1:2 classid 1:20 htb rate 220kbit ceil 256kbit prio 2
tc qdisc add dev eth0 parent 1:20 handle 20 sfq perturb 10
---------------------------------------------------------------

The stats:
---------------------------------------------------------------
[root@NL1000 htb]# tc -s -d qdisc show
qdisc sfq 20: dev eth0 quantum 1514b limit 128p flows 128/1024 perturb 10sec
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)

qdisc sfq 10: dev eth0 quantum 1514b limit 128p flows 128/1024 perturb 10sec Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc htb 1: dev eth0 r2q 10 default 20 direct_packets_stat 0 ver 3.6 Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)

[root@NL1000 htb]# tc -s -d class show dev eth0
class htb 1:10 parent 1:2 leaf 10: prio 1 quantum 1000 rate 26Kbit ceil 128Kbit
burst 1632b/8 mpu 0b cburst 1762b/8 mpu 0b level 0
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 401969 ctokens: 88149

class htb 1:2 root rate 256Kbit ceil 256Kbit burst 1926b/8 mpu 0b cburst 1926b/8 mpu 0b level 7
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 46975 ctokens: 46975

class htb 1:20 parent 1:2 leaf 20: prio 2 quantum 2816 rate 220Kbit ceil 256Kbit burst 1880b/8 mpu 0b cburst 1926b/8 mpu 0b level 0
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)
lended: 94 borrowed: 0 giants: 0
tokens: 53324 ctokens: 46975

[root@NL1000 htb]# tc -s -d filter show dev eth0
filter parent 1: protocol ip pref 100 u32
filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt
0 flowid 1:10
match 00170000/ffff0000 at 20

[root@NL1000 htb]# iptables -t mangle -L -nvx Chain PREROUTING (policy ACCEPT 3590 packets, 557751 bytes)
pkts bytes target prot opt in out source
destination

       0        0 MARK       tcp  --  *      *       0.0.0.0/0            
0.0.0.0/0          tcp dpt:23 MARK set 0x6
     146    12954 MARK       tcp  --  *      *       0.0.0.0/0            

0.0.0.0/0 tcp spt:23 MARK set 0x6

Chain OUTPUT (policy ACCEPT 315 packets, 16936 bytes)
pkts bytes target prot opt in out source
destination
---------------------------------------------------------------

So, what is going wrong?

Thanks in advance,

Signature · 1 line
Corey Rogers <[email protected]>
#2 lore raw
In reply to Nestor S A Melo

Em Qui, 2002-12-19 às 10:06, Nestor S A Melo escreveu:

Nestor,

First: If my english is poor, you can contact me direct by email in portuguese since I`m Brazilian too :)

So, somebody correct me if I`m wrong ( Stef? ):

1 - I think you share more bandwidth than you have allocated. 2 - In sfq directive, you should write:
#tc qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10
3 - You've marked packets with iptables -t mangle, but you're using u32 instead fw.I'm not sure if you did the correct u32 configuration too.

Probably you must use:

#tc filter add dev eth0 parent 1: protocol ip prio 100 handle 6 fw classid 1:10

The handle is the parameter that says to tc what mark you're using and fw is the parameter that says to tc that you're using a firewall mark.

I hope I have helped you

Miguel Figueiredo
Linux Suport Analist

Quoted 79 lines

I have a problem in setting up HTB.

It appears filters doesn't work at all, besides "tc filter show" show it as being correctly configured.

Class 1:10 never sent any traffic, but as iptables show below, it should be sending packets.

The HTB version I'm using is 3.3, with kernel 2.4.17.

The setup is as follows:
---------------------------------------------------------------
tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1 htb default 20 r2q 10

tc class add dev eth0 parent 1: classid 1:2 htb rate 256kbit

tc class add dev eth0 parent 1:2 classid 1:10 htb rate 26kbit ceil 128kbit prio
1
tc qdisc add dev eth0 parent 1:10 handle 10 sfq perturb 10
tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip sport 23 0xffff classid 1:10

tc class add dev eth0 parent 1:2 classid 1:20 htb rate 220kbit ceil 256kbit prio 2
tc qdisc add dev eth0 parent 1:20 handle 20 sfq perturb 10

---------------------------------------------------------------

The stats:
---------------------------------------------------------------
[root@NL1000 htb]# tc -s -d qdisc show
qdisc sfq 20: dev eth0 quantum 1514b limit 128p flows 128/1024 perturb 10sec
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)

qdisc sfq 10: dev eth0 quantum 1514b limit 128p flows 128/1024 perturb 10sec Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc htb 1: dev eth0 r2q 10 default 20 direct_packets_stat 0 ver 3.6 Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)

[root@NL1000 htb]# tc -s -d class show dev eth0
class htb 1:10 parent 1:2 leaf 10: prio 1 quantum 1000 rate 26Kbit ceil 128Kbit
burst 1632b/8 mpu 0b cburst 1762b/8 mpu 0b level 0
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 401969 ctokens: 88149

class htb 1:2 root rate 256Kbit ceil 256Kbit burst 1926b/8 mpu 0b cburst 1926b/8 mpu 0b level 7
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 46975 ctokens: 46975

class htb 1:20 parent 1:2 leaf 20: prio 2 quantum 2816 rate 220Kbit ceil 256Kbit burst 1880b/8 mpu 0b cburst 1926b/8 mpu 0b level 0
Sent 5116 bytes 94 pkts (dropped 0, overlimits 0)
lended: 94 borrowed: 0 giants: 0
tokens: 53324 ctokens: 46975

[root@NL1000 htb]# tc -s -d filter show dev eth0
filter parent 1: protocol ip pref 100 u32
filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt
0 flowid 1:10
match 00170000/ffff0000 at 20

[root@NL1000 htb]# iptables -t mangle -L -nvx Chain PREROUTING (policy ACCEPT 3590 packets, 557751 bytes)
pkts bytes target prot opt in out source
destination

       0        0 MARK       tcp  --  *      *       0.0.0.0/0            
0.0.0.0/0          tcp dpt:23 MARK set 0x6
     146    12954 MARK       tcp  --  *      *       0.0.0.0/0            

0.0.0.0/0 tcp spt:23 MARK set 0x6

Quoted 15 lines

Chain OUTPUT (policy ACCEPT 315 packets, 16936 bytes)
pkts bytes target prot opt in out source
destination
---------------------------------------------------------------

So, what is going wrong?

Thanks in advance,

Signature · 5 lines
_____________________
Nestor S A Melo
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Nestor S A Melo
Quoted 10 lines · Miguel Figueiredo

Em Qui, 2002-12-19 às 10:06, Nestor S A Melo escreveu:

Nestor,

First: If my english is poor, you can contact me direct by email in portuguese since I`m Brazilian too :)

So, somebody correct me if I`m wrong ( Stef? ):

1 - I think you share more bandwidth than you have allocated.

That's no problem. Rate of class 1:10 and 1:20 = 26+220=246kbit and rate of parent class is 256kbit.

Quoted 2 lines

2 - In sfq directive, you should write:
#tc qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10

His command will work too.

Quoted 10 lines

3 - You've marked packets with iptables -t mangle, but you're using u32 instead fw.I'm not sure if you did the correct u32 configuration too.

Probably you must use:

#tc filter add dev eth0 parent 1: protocol ip prio 100 handle 6 fw classid 1:10

The handle is the parameter that says to tc what mark you're using and fw is the parameter that says to tc that you're using a firewall mark.

And it's all in hex.

Stef

Signature · 9 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/