Skip to contentSkip to conversation

A small correction to LARTC (fwd)

LARTC Dragan Simic 2 participants 3 messages Jan 16, 2003

lore
Share & tools
lore
#0 lore raw

First of all, I have to say a big THANKS to all of you, your LARTC document really sheds some light in a soo dark place as, especially, Linux TC is.

I found a small error, or typo, in LARTC, on page 85, chapter 13.1. There is stated that "echo 2 > $i" would turn on RP filtering on actual interface, but there should be, instead, "echo 1 > $i". Also, in Documentation/networking/ip-sysctl.txt there are only two options for rp_filter - 0 (RPF off) or 1 (RPF on).

Also, on page 86, there is a FIXME about conf/{default,all}/* . I tried that, and it's out that setting only conf/all/rp_filter is enough for all already configured interfaces, and conf/default/rp_filter is intended to be used for interfaces that are just going to be configured, or better saying, link up'ed - for example ppp+ interfaces.

I already pointed this out, and you accepted this note, but in a recent version of LARTC I can see that the old version remained in the document.

Hope this would help, and keep up the good work !

Signature · 11 lines
.----------------------------------------------------------------------------.
| Pozdrav / Best Wishes,     [email protected]  | LL   The Choice of       |
| Dragan Simic                 RS.BA Hostmaster   | LL            GNU        |
| URC B.Luka / RSKoming.NET  System/Network Admin | LLLL i n u x  Generation |
`----------------------------------------------------------------------------'



_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

I had 2.4.x in mind when I wrote this about rp_filter values. In any case, in the LARTC should be cleared out what applies to 2.2 branch, and what to 2.4 branch. It's true, in 2.2.23, there are three options (0,1,2); and there are two options (0,1) in 2.4.20.

Quoted 16 lines · Michael T. Babcock
Quoted 3 lines · Dragan Simic

interface, but there should be, instead, "echo 1 > $i". Also, in Documentation/networking/ip-sysctl.txt there are only two options for rp_filter - 0 (RPF off) or 1 (RPF on).

At various points in history there have been values of 0, 1 and 2 available to mean different things. In my 2.2.14 source I have laying around, I see:

rp_filter - INTEGER
2 - do source validation by reversed path, as specified in RFC1812
...
1 - (DEFAULT) Weaker form of RP filtering: drop all the packets
...
0 - No source validation.

Signature · 12 lines
.----------------------------------------------------------------------------.
| Pozdrav / Best Wishes,     [email protected]  | LL   The Choice of       |
| Dragan Simic                 RS.BA Hostmaster   | LL            GNU        |
| URC B.Luka / RSKoming.NET  System/Network Admin | LLLL i n u x  Generation |
`----------------------------------------------------------------------------'




_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Dragan Simic

Hello,

Quoted 4 lines · Dragan Simic

I had 2.4.x in mind when I wrote this about rp_filter values. In any case, in the LARTC should be cleared out what applies to 2.2 branch, and what to 2.4 branch. It's true, in 2.2.23, there are three options (0,1,2); and there are two options (0,1) in 2.4.20.

	This is wrong, all kernels (2.2, 2.4, 2.5) treat 2 as 1,

i.e. only 1 and 0 are enough to distinguish the two possible states:
enable/disable source address validation. As for all/rp_filter, it is only a flag that says "0 disables the spoofing check for all interfaces". include/linux/inetdevice.h is a good source for information about whether 0 or 1 as value for all/XXX changes globally the feature for all interfaces. For rp_filter it is 0, for send_redirects it is 1.

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/