Skip to contentSkip to conversation

good hardware

LARTC Joshua Daniel Franklin 3 participants 3 messages Feb 5, 2003 – Feb 6, 2003

lore
Share & tools
lore
#0 lore raw

I've searched the list archives and haven't found any information on this.

I realize that many users are routing in a home or small office environment but I think there is also a place for "enterprise" routing. But knowing how to configure the software is only part of a low-latency router--you also need good hardware.

Are there any thoughts on good configurations?
NICs: I've seen several mentions of the Intel eepro NICs. Are they best?
Processor: speeds probably don't matter too much (my Cisco 3640 router
with 4 T1s has a 100Mhz processor, though it's RISC and has optimized IOS) but faster processors have faster FSB as well
Memory: 128 MB probably enough to deal with 100Mb?
HD: Obviously you want everything in memory, but if you're doing much
logging you might get a solid-state disk.

I've done a little comparison testing of prebuilt firewall routers with a few little DLink/Sonicwall/Netgear boxes vs. an Athlon running IPCop, but I'm sure someone has done better hardware tests than mine. I'm open to any info. If I get enough for a good summary perhaps it could be added to the HOWTO.
Thanks.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 1 line · Joshua Daniel Franklin

NICs: I've seen several mentions of the Intel eepro NICs. Are they best?

I still believe that the DEC ones are the best, you still can get new 100mbit nic with tulip chips on port, in our tests they are the best, we've about 1000 of them running here.

ps: intel does now produce that chips, but I don't know which intel nic models do contain that chip, as we buy cheap cards with that chip on it.

our dealer in munich, justs calls it

CompuShack FASTLine PCI 10/100Mbit/s DEC Chip 32 euro

under linux just load the tuplic.o module.

Quoted 4 lines

Processor: speeds probably don't matter too much (my Cisco 3640 router
with 4 T1s has a 100Mhz processor, though it's RISC and has optimized
IOS) but faster processors have faster FSB as well
Memory: 128 MB probably enough to deal with 100Mb?

not the amount of ram that is important, it's the memory throughoutput , as I can remember rambus is there better than ddr-ram.

ps: we only buy pcs with 512mb ram and 80gb hd, as it doesn't make much difference and someday you'll may need it ;-)

Quoted 2 lines

HD: Obviously you want everything in memory, but if you're doing much
logging you might get a solid-state disk.

and only write in chunks, not each entry alone and not in sync mode ;-)

Quoted 6 lines

I've done a little comparison testing of prebuilt firewall routers with a few little DLink/Sonicwall/Netgear boxes vs. an Athlon running IPCop, but I'm sure someone has done better hardware tests than mine. I'm open to any info. If I get enough for a good summary perhaps it could be added to the HOWTO.
Thanks.

look at the pci performace of the chipset, there are big differences

- --
Regards,
Robert
- ----------------
Robert Penz
robert.penz AT outertech.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.6 (GNU/Linux)
Comment: For info see http://www.gnupg.org

iD8DBQE+QY2T8tTsQqJDUBMRAgF4AJ9dUUU3oXTRIqs/XhnClT1dZ8lshQCgn9i4 jZnLT2lPOnrCfRDF7mWqutkŠTL
-----END PGP SIGNATURE-----

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Joshua Daniel Franklin

Joshua,

Quoted 6 lines · Joshua Daniel Franklin

I've searched the list archives and haven't found any information on this.

I realize that many users are routing in a home or small office environment but I think there is also a place for "enterprise" routing. But knowing how to configure the software is only part of a low-latency router--you also need good hardware.

Yes, but sometimes software in conjunction with how you using the hardware. Not one or the other. However as I will mention below I have a dinosaur that screams.

However I totally agree with you on the "enterprise" aspect. They stand to gain the most. I just won't say that to my buddies that are engineers over at Cisco.

Quoted 2 lines

Are there any thoughts on good configurations?
NICs: I've seen several mentions of the Intel eepro NICs. Are they best?

I prefer Intel cards. Most of my nics are Intel Pro100 S adapters using Intel's e100 driver and I couldn't be happier. However some prefer some of Intel's other drivers that can be fully compiled into the kernel. Personally I prefer my drivers to be loaded by the kernel, and not part of. Everything else I do compile into the kernel.

It just so happens I also have also have a Linksys LNE100TX on a picky machine that will not accept the Intel's? It uses the tulip driver, and I have never been able to force duplex and speed on that card. It wants to remain in auto-negotiate mode? Luckily the machine is not a critical one. Just a spare machine used for fun and headaches. Since others say that tulip is a good driver I will assume that nic is a piece of s***.

Another chipset I absolutely hate is anything from National Semiconductor using the 83815 chipset and the dp83815 driver.

Another one that I have never been able to force duplex and speed.

Now another really cool thing about Intel nics I like is IANS. Look into it, as there is much you can do with it.

Quoted 6 lines

Processor: speeds probably don't matter too much (my Cisco 3640 router
with 4 T1s has a 100Mhz processor, though it's RISC and has optimized IOS) but faster processors have faster FSB as well
Memory: 128 MB probably enough to deal with 100Mb?
HD: Obviously you want everything in memory, but if you're doing much
logging you might get a solid-state disk.

I would think RAM, the type of RAM and the bus speed to mean more than the proc. I would imagine 128 to be plenty, depending on how much space is used for your root file system and how much is left over to be used as memory. Although I doubt you could go wrong with more memory.

FYI, while my network is much smaller with a smaller load, I have seen some pretty substantial differences in my Linux gear, and my dedicated networking devices.

I have a load balancing (sort of) Linux router as my core router. It an old machine that boots off a zip disk and runs entirely out of RAM. 75mhz Pentium, with 32mb RAM, 16 for file system, 16 for memory. Ancient RAM. Maybe on a good day 66mhz bus?

All tests so far show that the latency of packets going through it is on average half that of the latency of packets going through either one of my Netopia routers, or my Cicso 827.

The Linux router responds twice as fast when being pinged. So there could definitely be some gains. Although there could also be some draw backs. That depends on your situation.

Quoted 3 lines

I've done a little comparison testing of prebuilt firewall routers with a few little DLink/Sonicwall/Netgear boxes vs. an Athlon running IPCop, but I'm sure someone has done better hardware tests than mine.

That would not be me. ;)

Signature · 22 lines
Sincerely,
William L. Thomson Jr.
Obsidian-Studios, Inc.
439 Amber Way
Petaluma, Ca. 94952
Phone  707.766.9509
Fax    707.766.8989
http://www.obsidian-studios.com
-- 
Sincerely,
William L. Thomson Jr.
Support Group
Obsidian-Studios Inc.
439 Amber Way
Petaluma, Ca. 94952
Phone  707.766.9509
Fax    707.766.8989
http://www.obsidian-studios.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/