2.4.20 htb3 oops
I have arranged a serial console with logging to a terminal client, so next time it happens I will have the output from the panic.
For the record:
One of the machines crashed again this night at 11.30 p.m. (local time). I noticed that the MRTG graph looks a bit odd:
http://hem.wasadata.net/goran/mrtg.png
The total limit is set to12Mbit, as you probably can see if you check the ruleset in my first post. Even about 2-4 hours before the crash the graph shows two network traffic "spikes". The first one tops at about 22Mbps of outgoing traffic on the interface and the second one tops 28Mbps of incoming traffic.
Could this have anything to do with the crash?
Many Thanks,
Göran
----- Original Message -----
From: Abraham van der Merwe <[email protected]>
To: Göran Runfeldt <[email protected]>
Cc: <[email protected]>
Sent: Monday, March 03, 2003 5:29 PM
Subject: Re: [LARTC] 2.4.20 htb3 oops
Hi G?ran!
Unfortunately that is not going to help much since you can't figure out from the information below where in the code it crashes. Next time, please copy the entire kernel panic (including stack trace) and run it through ksymoops or look up the symbols in vmlinux.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hep
Quoted 8 lines · Göran Runfeldt
I have arranged a serial console with logging to a terminal client, so next time it happens I will have the output from the panic.
For the record:
One of the machines crashed again this night at 11.30 p.m. (local time). I noticed that the MRTG graph looks a bit odd:
http://hem.wasadata.net/goran/mrtg.png
Quoted 6 lines
The total limit is set to12Mbit, as you probably can see if you check the ruleset in my first post. Even about 2-4 hours before the crash the graph shows two network traffic "spikes". The first one tops at about 22Mbps of outgoing traffic on the interface and the second one tops 28Mbps of incoming traffic.
Could this have anything to do with the crash?
Any solution to the problems describe above? Im currently looking into building a new kernel 2.4.20 with HTB compiled as module in a production enviroment (2,5mbits average, 6-10mbits/peak). I wont use it if its broken though?
Signature · 14 lines
Venlig hilsen/Kind regards Thomas Kirk ARKENA tlf/phone +04570233456 thomas(at)arkena(dot)com Http://www.arkena.com Oh, give me a home, Where the buffalo roam, And I'll show you a house with a really messy kitchen. _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 8 lines
Any solution to the problems describe above? Im currently looking into building a new kernel 2.4.20 with HTB compiled as module in a production enviroment (2,5mbits average, 6-10mbits/peak). I wont use it if its broken though?
Unfortunately we have not yet come to a solution when it comes to our problems.
We have had the machines running for more than five days now, without any HTB qdisc/classes loaded. This confirms that this is a problem with HTB. I have activated the rules again in hope of getting a useful crash dump.
I do not know if anyone else has or will have this problem. All I know is that we have the problem over here.
Göran
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/