policy routing problem
hello list subscribers, i may have been too cocky in my previous posts regarding this policy routing problem of mine. (my old posts in further down).
the problem that i cannot reach any defined network from the router still exists. i though that would be solved when adding "from interface-address, use routing table 'all'". well, it didnt.
what i can conclude, with some help from tcpdump, from this is that the router can see the routing table when trying to reach a defined network.
the routing table looks pretty much like this: "network a could be reached via router x". my router does send away a arp request to router x in order to send the packet through it, and router x does indeed reply, so everything tcpdump shows is these two packets, nothing more.
'ping a' on the router returns:
root@ibus-router:~# ping 172.16.1.2 PING 172.16.1.2 (172.16.1.2): 56 octets data sendto: Network is unreachable ping: sent 64 octets to 172.16.1.2, ret=-1
i have googled on this but without any meaningful results.
i was also concerned with the fact that only adding the interface address in the rules would be a problem, and it is. the arp reply from router x will be routed according to table 'main' and thus not reach the origin address. so i simpy added router x's address to the rules and told it to use table 'all'. i still cannot reach network a from the router.
the thing i seem to think is the most difficult to understand here is that route lookup is correct, otherwise the arp request wouldnt be sent, but the packet never leaves the router.
this is how i see it:
1. router is requested by me to ping network a
2. router looks in the RPDB to see which routing table to use
3. RPDB says "use table 'all'"
4. router looks after a route to network a in routing table 'all'
5. router finds a route to network a and understands that it has to send it via router x
6. router checks arp cache, doesnt see anything for router x
7. router sends out a arp request to router x
8. router x answers with a arp reply
(this is where nothing happends)
9. router _should_ compose a packet and send it to router x
ip route flush cache is not a problem.
any insight on this would be helpful. thank you for your time and for reading this far.
best regards,
tomas bonnedahl
Quoted 83 lines · Tomas Bonnedahl
hello again list. i have another solution to this that has some advantages over my last post.
when dealing with packets and their 'coming-back' i choosed to add routes to these networks in table 'main', instead i can create two more rules (a total of four rules altogether) that looks like the first two but uses the to parameter unstead of the from. (they'll just say "packets that is going to x, use table 'all'").
-tomas bonnedahl
Quoted 70 lines · Tomas Bonnedahl
i have some additional information regarding this issue with policy routing.
on the router that has policy routing implemented, read further down for more information on my gols, three ethernet interfaces exists.
since the routing table 'main' just consists of a route to 192.168.1/24 with a prohihbit 0/0, you cannot from the router reach a network that is located on some of the other interfaces than 192.168.1/24 exists on. this is because the src address in the packet will be the address of that interface which the packet will exit. according to the rules that exists in the RPDB, that address will use the routing table 'main' which, in turn, does not have a route to that network.
the solution to this would be to:
1. make (two) rules which says "if the src address of a packet is the adress of an interface, use table 'all'". (also note that im using the /32 address)
2. add, in routing table 'main', routes to these /32 addresses.the first part here is used so that a packet could be _sent_ away correct, the second part is used so that a packets can come _back_ correct.
im sure martin have some insight in this, perhaps a simpler solution?
indeed, i did not think of this when implementing policy routing since i was only concerned with networks and not the router itself.
i hope this will help someone struggeling with policy routing.
best regards,
tomas bonnedahlQuoted 37 lines · Tomas Bonnedahl
hello list (and martin) ;x
i have now composed my final(?) policy routing design.
the goals i had when beginning with this, for you that have not follow mine and martins thread, was to 1) only let 192.168.1/24 to see all routes,
2) not route between defined networks, except to and from 192.168.1/24 and 3) not defined networks should only be able to reach 192.168.1/24.this might sound simple. it wasnt for me.
the solution i came up with, after days and days of thinking (and patience) was this:
two routing tables, one called "ALL" that, suprisingly, held routes to all networks defined and a default route to internet. the other called "main", just for ease, that held one route to 192.168.1/24 and had a default prohibit.
the one rule that exists just says "if src = 192.168.1/24 use table ALL". of course there is an additional rule, the standard one that says "from all lookup main" with a number of 32766.
so, for you that doesnt understand my poor english, literally every network that passes, except from 192.168.1/24, will use the main table that just holds the route to 192.168.1/24 and the prohibit one.
this so simple, something just has to be wrong. feel free to englighten me.
please flame.
best regards,
tomas bonnedahl
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 8 lines
Quoted 4 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
i think i may know what the problem can be here.
the order of what happends here is crucial, if the router wants to know what interface the packet is supposed to exit on and hence use that address as source, it needs to do a lookup in the routing table. while this is processing, the router cannot contribute a src address to the RPDB, thus the rule "from router, lookup 'main'" will not match.
what will match is the rule "from all use 'main'". but 'main' doesnt hold this route.
though this does not explain the arp packets being sent between the router and router x.
argh, can someone please explain this to me?
regards,
tomas bonnedahl
Quoted 140 lines · Tomas Bonnedahl
hello list subscribers, i may have been too cocky in my previous posts regarding this policy routing problem of mine. (my old posts in further down).
the problem that i cannot reach any defined network from the router still exists. i though that would be solved when adding "from interface-address, use routing table 'all'". well, it didnt.
what i can conclude, with some help from tcpdump, from this is that the router can see the routing table when trying to reach a defined network.
the routing table looks pretty much like this: "network a could be reached via router x". my router does send away a arp request to router x in order to send the packet through it, and router x does indeed reply, so everything tcpdump shows is these two packets, nothing more.
'ping a' on the router returns:
root@ibus-router:~# ping 172.16.1.2 PING 172.16.1.2 (172.16.1.2): 56 octets data sendto: Network is unreachable ping: sent 64 octets to 172.16.1.2, ret=-1i have googled on this but without any meaningful results.
i was also concerned with the fact that only adding the interface address in the rules would be a problem, and it is. the arp reply from router x will be routed according to table 'main' and thus not reach the origin address. so i simpy added router x's address to the rules and told it to use table 'all'. i still cannot reach network a from the router.
the thing i seem to think is the most difficult to understand here is that route lookup is correct, otherwise the arp request wouldnt be sent, but the packet never leaves the router.
this is how i see it:
1. router is requested by me to ping network a
2. router looks in the RPDB to see which routing table to use
3. RPDB says "use table 'all'"
4. router looks after a route to network a in routing table 'all'
5. router finds a route to network a and understands that it has to send it via router x
6. router checks arp cache, doesnt see anything for router x
7. router sends out a arp request to router x
8. router x answers with a arp reply
(this is where nothing happends)
9. router _should_ compose a packet and send it to router xip route flush cache is not a problem.
any insight on this would be helpful. thank you for your time and for reading this far.
best regards,
tomas bonnedahlQuoted 87 lines · Tomas Bonnedahl
hello again list. i have another solution to this that has some advantages over my last post.
when dealing with packets and their 'coming-back' i choosed to add routes to these networks in table 'main', instead i can create two more rules (a total of four rules altogether) that looks like the first two but uses the to parameter unstead of the from. (they'll just say "packets that is going to x, use table 'all'").
-tomas bonnedahl
Quoted 74 lines · Tomas Bonnedahl
i have some additional information regarding this issue with policy routing.
on the router that has policy routing implemented, read further down for more information on my gols, three ethernet interfaces exists.
since the routing table 'main' just consists of a route to 192.168.1/24 with a prohihbit 0/0, you cannot from the router reach a network that is located on some of the other interfaces than 192.168.1/24 exists on. this is because the src address in the packet will be the address of that interface which the packet will exit. according to the rules that exists in the RPDB, that address will use the routing table 'main' which, in turn, does not have a route to that network.
the solution to this would be to:
1. make (two) rules which says "if the src address of a packet is the adress of an interface, use table 'all'". (also note that im using the /32 address)
2. add, in routing table 'main', routes to these /32 addresses.the first part here is used so that a packet could be _sent_ away correct, the second part is used so that a packets can come _back_ correct.
im sure martin have some insight in this, perhaps a simpler solution?
indeed, i did not think of this when implementing policy routing since i was only concerned with networks and not the router itself.
i hope this will help someone struggeling with policy routing.
best regards,
tomas bonnedahlQuoted 29 lines · Tomas Bonnedahl
hello list (and martin) ;x
i have now composed my final(?) policy routing design.
the goals i had when beginning with this, for you that have not follow mine and martins thread, was to 1) only let 192.168.1/24 to see all routes,
2) not route between defined networks, except to and from 192.168.1/24 and 3) not defined networks should only be able to reach 192.168.1/24.this might sound simple. it wasnt for me.
the solution i came up with, after days and days of thinking (and patience) was this:
two routing tables, one called "ALL" that, suprisingly, held routes to all networks defined and a default route to internet. the other called "main", just for ease, that held one route to 192.168.1/24 and had a default prohibit.
the one rule that exists just says "if src = 192.168.1/24 use table ALL". of course there is an additional rule, the standard one that says "from all lookup main" with a number of 32766.
so, for you that doesnt understand my poor english, literally every network that passes, except from 192.168.1/24, will use the main table that just holds the route to 192.168.1/24 and the prohibit one.
this so simple, something just has to be wrong. feel free to englighten me.
Quoted 8 lines
please flame.
best regards,
tomas bonnedahl
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 8 lines
Quoted 4 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
hello martin, i was sitting here and waiting for your answer, thank you ;x
(for ease in the migration i use table 'main' with all routes and table 'test' with only routes to 192.168.1/24 and prohibit 0/0.)
root@ibus-router:~# ip rule show 0: from all lookup local 31000: from 172.16.1.2 to 195.43.36.55 lookup main 31100: from 195.43.36.55 to 172.16.1.2 lookup main 32000: from 192.168.1.0/24 lookup main 32100: from 192.168.4.0/24 lookup main 32200: from 192.168.2.0/24 lookup main 32300: from all to 192.168.4.1 lookup main 32400: from all to 192.168.2.2 lookup main 32500: from all lookup test 32766: from all lookup main 32767: from all lookup default
root@ibus-router:~# ip route show table main 192.168.4.0/24 dev eth2 scope link 192.168.2.0/24 dev eth0 scope link 192.168.1.0/24 dev eth1 scope link 10.47.17.0/24 via 192.168.2.1 dev eth0 172.16.1.0/24 via 192.168.4.2 dev eth2 10.46.23.0/24 via 192.168.2.1 dev eth0 192.168.75.0/24 via 192.168.2.1 dev eth0 10.100.0.0/16 via 192.168.2.1 dev eth0 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev eth0
root@ibus-router:~# ip route show table test 192.168.1.0/24 dev eth1 scope link 127.0.0.0/8 dev lo scope link prohibit default
things i like to clarify:
1. rules 31000 and 31100 is just so that one address on a defined network can reach an address on the internet, and that works perfect.
2. rules 32100-32400 is supposed to be so that the router can reach defined networks, this does not work.
3. the reason of having so many routes in table main is just plain stupid when the default is the same as there "via..". i will change this in a near future but i added the networks so that it would be more clear what i was doing.
some ascii art over the network:
internet --------------------------| fw | -- some defined networks over ipsec
192.168.2.1/24
|
|
192.168.2.2/24
voip 192.168.4.2/24 ------ 192.168.4.1/24| router |192.168.1.1 -- LAN (192.168.1/24)i hope you understand, please mail back if there is some more information you would like.
thanks,
tomas
Quoted 178 lines · Martin A. Brown
Tomas,
I'd like to look at your problem, but need a few more details.
Would you post the output of "ip rule show" and "ip route show" "ip route show table all" (and any other tables.
I like your sequence of 8 events....that help me understand your problem....
Thank you,
-Martin
: i think i may know what the problem can be here.
:
: the order of what happends here is crucial, if the router wants to know
: what interface the packet is supposed to exit on and hence use that
: address as source, it needs to do a lookup in the routing table. while
: this is processing, the router cannot contribute a src address to the
: RPDB, thus the rule "from router, lookup 'main'" will not match.
:
: what will match is the rule "from all use 'main'". but 'main' doesnt
: hold this route.
:
: though this does not explain the arp packets being sent between the router and router x. :
:
: argh, can someone please explain this to me?
:
: regards,
: tomas bonnedahl
:
: On Wed, Mar 12, 2003 at 05:55:27PM +0100, Tomas Bonnedahl wrote:
: > hello list subscribers, i may have been too cocky in my previous posts regarding this : > policy routing problem of mine. (my old posts in further down).
: >
: > the problem that i cannot reach any defined network from the router still exists.
: > i though that would be solved when adding "from interface-address, use routing table : > 'all'". well, it didnt.
: >
: > what i can conclude, with some help from tcpdump, from this is that the router can
: > see the routing table when trying to reach a defined network.
: >
: > the routing table looks pretty much like this: "network a could be reached via router x". : > my router does send away a arp request to router x in order to send the packet through it, and : > router x does indeed reply, so everything tcpdump shows is these two packets, nothing more. : >
: > 'ping a' on the router returns:
: >
: > root@ibus-router:~# ping 172.16.1.2
: > PING 172.16.1.2 (172.16.1.2): 56 octets data
: > sendto: Network is unreachable
: > ping: sent 64 octets to 172.16.1.2, ret=-1
: >
: > i have googled on this but without any meaningful results.
: >
: > i was also concerned with the fact that only adding the interface address in the rules : > would be a problem, and it is. the arp reply from router x will be routed according to table : > 'main' and thus not reach the origin address. so i simpy added router x's address to the rules and : > told it to use table 'all'. i still cannot reach network a from the router.
: >
: > the thing i seem to think is the most difficult to understand here is that route lookup is : > correct, otherwise the arp request wouldnt be sent, but the packet never leaves the router. : >
: > this is how i see it:
: > 1. router is requested by me to ping network a
: > 2. router looks in the RPDB to see which routing table to use
: > 3. RPDB says "use table 'all'"
: > 4. router looks after a route to network a in routing table 'all'
: > 5. router finds a route to network a and understands that it has to send it via router x : > 6. router checks arp cache, doesnt see anything for router x
: > 7. router sends out a arp request to router x
: > 8. router x answers with a arp reply
: > (this is where nothing happends)
: > 9. router _should_ compose a packet and send it to router x
: >
: > ip route flush cache is not a problem.
: >
: > any insight on this would be helpful. thank you for your time and for reading this far. : >
: >
: > best regards,
: > tomas bonnedahl
: >
: >
: > On Tue, Mar 11, 2003 at 06:07:03PM +0100, Tomas Bonnedahl wrote:
: > > hello again list. i have another solution to this that has some
: > > advantages over my last post.
: > >
: > > when dealing with packets and their 'coming-back' i choosed to add routes
: > > to these networks in table 'main', instead i can create two more rules (a
: > > total of four rules altogether) that looks like the first two but uses
: > > the to parameter unstead of the from. (they'll just say "packets that is going
: > > to x, use table 'all'").
: > >
: > >
: > > -tomas bonnedahl
: > >
: > > On Tue, Mar 11, 2003 at 05:32:51PM +0100, Tomas Bonnedahl wrote:
: > > > i have some additional information regarding this issue with policy routing.
: > > >
: > > > on the router that has policy routing implemented, read further down for
: > > > more information on my gols, three ethernet interfaces exists.
: > > >
: > > > since the routing table 'main' just consists of a route to 192.168.1/24
: > > > with a prohihbit 0/0, you cannot from the router reach a network
: > > > that is located on some of the other interfaces than 192.168.1/24 exists
: > > > on. this is because the src address in the packet will be the address of
: > > > that interface which the packet will exit. according to the rules that exists
: > > > in the RPDB, that address will use the routing table 'main' which, in turn,
: > > > does not have a route to that network.
: > > >
: > > > the solution to this would be to:
: > > > 1. make (two) rules which says "if the src address of a packet is the adress
: > > > of an interface, use table 'all'". (also note that im using the /32 address)
: > > > 2. add, in routing table 'main', routes to these /32 addresses.
: > > >
: > > > the first part here is used so that a packet could be _sent_ away correct, the
: > > > second part is used so that a packets can come _back_ correct.
: > > >
: > > > im sure martin have some insight in this, perhaps a simpler solution?
: > > >
: > > > indeed, i did not think of this when implementing policy routing since i was
: > > > only concerned with networks and not the router itself.
: > > >
: > > > i hope this will help someone struggeling with policy routing.
: > > >
: > > >
: > > > best regards,
: > > > tomas bonnedahl
: > > >
: > > > On Thu, Mar 06, 2003 at 04:31:42PM +0100, Tomas Bonnedahl wrote:
: > > > > hello list (and martin) ;x
: > > > >
: > > > > i have now composed my final(?) policy routing design.
: > > > >
: > > > > the goals i had when beginning with this, for you that have not follow
: > > > > mine and martins thread, was to 1) only let 192.168.1/24 to see all routes,
: > > > > 2) not route between defined networks, except to and from 192.168.1/24 and 3) not : > > > > defined networks should only be able to reach 192.168.1/24.
: > > > >
: > > > > this might sound simple. it wasnt for me.
: > > > >
: > > > > the solution i came up with, after days and days of thinking (and patience) was : > > > > this:
: > > > >
: > > > > two routing tables, one called "ALL" that, suprisingly, held routes to all networks defined : > > > > and a default route to internet. the other called "main", just for ease, that held one route to : > > > > 192.168.1/24 and had a default prohibit.
: > > > >
: > > > > the one rule that exists just says "if src = 192.168.1/24 use table ALL". of course there is : > > > > an additional rule, the standard one that says "from all lookup main" with a number of 32766. : > > > >
: > > > > so, for you that doesnt understand my poor english, literally every network that passes, except : > > > > from 192.168.1/24, will use the main table that just holds the route to 192.168.1/24 and the : > > > > prohibit one.
: > > > >
: > > > >
: > > > > this so simple, something just has to be wrong. feel free to englighten me.
: > > > >
: > > > >
: > > > > please flame.
: > > > >
: > > > > best regards,
: > > > > tomas bonnedahl
: > > > > _______________________________________________
: > > > > LARTC mailing list / [email protected]
: > > > > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
: > > > >
: > > > _______________________________________________
: > > > LARTC mailing list / [email protected]
: > > > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
: > > >
: > > _______________________________________________
: > > LARTC mailing list / [email protected]
: > > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
: > >
Quoted 13 lines
: > _______________________________________________
: > LARTC mailing list / [email protected]
: > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
: >
: _______________________________________________
: LARTC mailing list / [email protected]
: http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
:Signature · 1 line
Martin A. Brown --- SecurePipe, Inc. --- [email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi Tomas,
: hello martin, i was sitting here and waiting for your answer, thank you : ;x
I hope you didn't sit there waiting for this answer!
: (for ease in the migration i use table 'main' with all routes and table : 'test' with only routes to 192.168.1/24 and prohibit 0/0.) :
: root@ibus-router:~# ip rule show
: 0: from all lookup local : 31000: from 172.16.1.2 to 195.43.36.55 lookup main : 31100: from 195.43.36.55 to 172.16.1.2 lookup main : 32000: from 192.168.1.0/24 lookup main : 32100: from 192.168.4.0/24 lookup main : 32200: from 192.168.2.0/24 lookup main : 32300: from all to 192.168.4.1 lookup main : 32400: from all to 192.168.2.2 lookup main : 32500: from all lookup test : 32766: from all lookup main : 32767: from all lookup default : : root@ibus-router:~# ip route show table main : 192.168.4.0/24 dev eth2 scope link : 192.168.2.0/24 dev eth0 scope link : 192.168.1.0/24 dev eth1 scope link
: 10.47.17.0/24 via 192.168.2.1 dev eth0
: 172.16.1.0/24 via 192.168.4.2 dev eth2
: 10.46.23.0/24 via 192.168.2.1 dev eth0
: 192.168.75.0/24 via 192.168.2.1 dev eth0
: 10.100.0.0/16 via 192.168.2.1 dev eth0
: 127.0.0.0/8 dev lo scope link
: default via 192.168.2.1 dev eth0
:
: root@ibus-router:~# ip route show table test
: 192.168.1.0/24 dev eth1 scope link
: 127.0.0.0/8 dev lo scope link
: prohibit default
:
: things i like to clarify:
: 1. rules 31000 and 31100 is just so that one address on a defined network can reach an
: address on the internet, and that works perfect.
Looks perfect.
: 2. rules 32100-32400 is supposed to be so that the router can reach
: defined networks, this does not work.
This may be part of the "which comes first, the chicken or the egg" scenario you alluded to in your previous mail. I'm still trying to wrap my mind around the intertwined relationship between source address selection and route selection. I can't answer your implied question about why this doesn't work, nor can I answer your previous question about the ARP queries which never have a following ethernet frame with IP payload.
Maybe one of the people more familiar with the kernel source code can help out here.
: 3. the reason of having so many routes in table main is just plain stupid
: when the default is the same as there "via..". i will change this in : a near future but i added the networks so that it would be more : clear what i was doing.
Clarity appreciated.
: some ascii art over the network:
How about some modified ASCII art! Everybody loves ASCII....
0/0 internet -----+ +-------------+ +---- defined networks ipsec
\| fw |/ 10.47.17.0/24
+-------------+ 10.46.23.0/24
192.168.2.1/24 10.100.0.0/16
| 192.168.75.0/24
|
192.168.2.2/24
+-------------+
192.168.4.1/24 /| linux router|\ 192.168.1.1/24
/ +-------------+ +--- LAN
192.168.4.2/24 /
+------------+
| voip |
+------------+
|
+-- 172.16.1.0/24This is what I'm able to gather from your routes and diagram, and you, sir, have a garden of networks.
I think what you want to do on "linux router" is to try the following (idiomatic) RPDB entry.
# ip rule add iif lo table all # -- or table main in above case
I know it seems a very simple answer, to a complex question, but I hope it will work for you.
By the way, Tomas, did you know that you can have rule types in the RPDB, e.g.,
# ip rule add blackhole from 192.168.4.2 to 10.0.0.0/8 # ip rule add prohibit from 10.47.17.0/24 to 172.16.1.0/24 # ip rule add unreachable from 192.168.75.0/24 to 192.168.4.0/24
OK, I know that tidbit doesn't help you in your current troubles, but I was hoping that the "iif lo" trick might help.
-Martin
Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 1 line · Martin A. Brown
Hi Tomas,
hello again.
Quoted 1 line
I hope you didn't sit there waiting for this answer!
this time no. ;)
Quoted 9 lines
: things i like to clarify:
: 1. rules 31000 and 31100 is just so that one address on a defined network can reach an
: address on the internet, and that works perfect.Looks perfect.
: 2. rules 32100-32400 is supposed to be so that the router can reach
: defined networks, this does not work.
Quoted 6 lines
This may be part of the "which comes first, the chicken or the egg" scenario you alluded to in your previous mail. I'm still trying to wrap my mind around the intertwined relationship between source address selection and route selection. I can't answer your implied question about why this doesn't work, nor can I answer your previous question about the ARP queries which never have a following ethernet frame with IP payload.
exactly my thought too with the "chicken or egg". i have looked at the iproute2 src code and also the kernel route.c code but since im not that good of a programmer i couldnt make anything out of it.
i may be stupid here, the arp quierys were sent when i was trying to ping the voIP network, but it _could_ have come from legatime traffic from the lan (the works) so the arp request didnt necessarily had to come in conjunction with my ping. im not sure but when we have now looked further into this, it seems possible that it was not from ping but from other traffic.
Quoted 2 lines
Maybe one of the people more familiar with the kernel source code can help out here.
yes. though im not sure anyone still reads this thread anymore, if anyone ever did. ;/
Quoted 21 lines
: some ascii art over the network:
How about some modified ASCII art! Everybody loves ASCII....
0/0 internet -----+ +-------------+ +---- defined networks ipsec \| fw |/ 10.47.17.0/24 +-------------+ 10.46.23.0/24 192.168.2.1/24 10.100.0.0/16 | 192.168.75.0/24 | 192.168.2.2/24 +-------------+ 192.168.4.1/24 /| linux router|\ 192.168.1.1/24 / +-------------+ +--- LAN 192.168.4.2/24 / +------------+ | voip | +------------+ | +-- 172.16.1.0/24
Quoted 2 lines
This is what I'm able to gather from your routes and diagram, and you, sir, have a garden of networks.
indeed true. you figured it out and made a much better outline than me.
Quoted 4 lines
I think what you want to do on "linux router" is to try the following (idiomatic) RPDB entry.
# ip rule add iif lo table all # -- or table main in above case
hm. i do not have the possibility to check this right now, but i will do it as soon as possible. but i have to tell you, i really dont see what this "means" or will change. just that everything that exits (and enters?) on the loopback if will use table all?
Quoted 2 lines
I know it seems a very simple answer, to a complex question, but I hope it will work for you.
well, so do i ;)
Quoted 6 lines
By the way, Tomas, did you know that you can have rule types in the RPDB, e.g.,
# ip rule add blackhole from 192.168.4.2 to 10.0.0.0/8 # ip rule add prohibit from 10.47.17.0/24 to 172.16.1.0/24 # ip rule add unreachable from 192.168.75.0/24 to 192.168.4.0/24
yes, i knew that. i choosed prohibit since the blackhole just drops them on the floor and let the client time out.
Quoted 2 lines
OK, I know that tidbit doesn't help you in your current troubles, but I was hoping that the "iif lo" trick might help.
ill check later today and ill mail back to you as soon as possible afterwards.
thank you martin
regards,
tomas
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hello..
I Use mandrake 9.1 with a custom kernel. Policy routing etc. all routing options selected while compile the kernel (2.4.22)..
System is a PC and contain 4 ethernet.
eth0, a local subnet. 192.168.0.1
eth1, a ADSL modem. pppoe run this interface and ppp0 already up. Interface numbered as 10.0.0.1 for access modem, and ppp0 masqueraded for outgoing connections (with $IPT -A POST.. -o ppp0 -j MASQUERADE)
eth2, connect a FR line with a router and address 195.174.43.34 eth3, connect a DMZ with 212.174.154.128/25
Other hand, we use a /28 block for local subnet. eth2 masquerade packets from local lan to using iptables ... DNAT.
ADSL line newly connected, 2048/512 kbps.
Only FR line router defined as default gw.
This system currently working fine, but don't use ADSL..
I want this reason:
All http request use ADSL line.
OR
Only a machine from DMZ (its a proxy server) use this ADSL line..
I read HOWTO and other sources, and test this commands:
echo 200 http >>/etc/iproute2/rttables (!?)
ip rule add fwmark 10001 table http
ip route add default via 81.215.8.1 table http ip route flush cache
iptables -t mangle -A PREROUTING -p tcp --dport 80 \
-j MARK --set-mark 10001
For this state, policy routing don't any effect. ppp0 TX/RX Values same always.
I try this rule.
ip rule add from 212.174.154.219 table http
Wow... This machine can't reach internet for this reason :(( No routing..
I try, cut-edit-paste HOWTO lines. Create table john etc.. But same result :((
I'm confused. You can help me ?
Excuse me for poor english :(
Thanks..
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi, i'm a stupid :))
Sorry, i forget first policy: RTFM..
Quoted 1 line · On Mon, 8 Dec 2003 20:21:06 +0200 Serdar KÖYLÜ <[email protected]> wrote:
ip rule add fwmark 10001 table http
ip uses hexadecimal notation. This number really 0x10001
Quoted 4 lines
ip route add default via 81.215.8.1 table http ip route flush cache
iptables -t mangle -A PREROUTING -p tcp --dport 80 \
-j MARK --set-mark 10001
but, iptables uses radix decimal.
I try "--set-mark 0x10001" and it's work fine..
Quoted 5 lines
ip rule add from 212.174.154.219 table http
Wow... This machine can't reach internet for this reason :(( No routing..
But this reason don't resolved.. Why ?
Thanks..
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/