Skip to contentSkip to conversation

ip routing problems in 2.4.20

LARTC Ard van Breemen 3 participants 6 messages May 5, 2003 – May 6, 2003

lore
Share & tools
lore
#0 lore raw

Hi,
Has anybody noticed that when:
ip addr add 192.168.0.1/32 dev eth0
ip route add 192.168.0.2/32 dev eth0

The system will not respond to arprequests from 192.168.0.2, even when rp_filter=0, proxy_arp=1, etc...

I will investigate it further at another time, but this has caused me a lot of headaches... Grrr...

Signature · 8 lines
mail          up  170+00:33,     7 users,  load 0.16, 0.22, 0.17
mistar1       up   28+18:37,    17 users,  load 0.22, 0.08, 0.04
Let your government know you value your freedom: sign the petition:
http://petition.eurolinux.org

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 4 lines · Ard van Breemen

Hi,
Has anybody noticed that when:
ip addr add 192.168.0.1/32 dev eth0
ip route add 192.168.0.2/32 dev eth0

/32? this would be a subnetmask with one host per subnet - so how could the host communicate with a router in it's own subnet? not at all.

it seems to me this doesn't make much sense. maybe i just haven't got the point.

greetings, ulric

Signature · 6 lines
ulrich schwarz, computing center, university of ulm, germany


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Ard van Breemen
Quoted 8 lines · ulrich schwarz
Quoted 4 lines · Ard van Breemen

Hi,
Has anybody noticed that when:
ip addr add 192.168.0.1/32 dev eth0
ip route add 192.168.0.2/32 dev eth0

/32? this would be a subnetmask with one host per subnet - so how could the host communicate with a router in it's own subnet? not at all.

The use of whatever ip address to bind an interface to the ip stack should not have any consequences to the arp behaviour if rp_filter=0. If I said:
ip addr add 127.0.0.1/32 dev eth0
ip link set up eth0
echo 0 > /proc/sys/net/ipv4/conf/eth0/rp_filter

it should answer any arp request for any of it's ip addresses. Adding a route to a device only makes sure that you can make rp_filter=1.
At least that used to be the behaviour before 2.4.20. I've tested a lot of this stuff, and it is used in a lot of places (not only by me). It would hurt a lot of people if it does not work any more.

Quoted 2 lines

it seems to me this doesn't make much sense. maybe i just haven't got the point.

Split a /24 in a lot of smaller subnets on a firewall with > 50 interfaces.

Signature · 8 lines
mail          up  170+01:42,     8 users,  load 0.08, 0.14, 0.20
mistar1       up   28+19:46,    17 users,  load 0.02, 0.01, 0.00
Let your government know you value your freedom: sign the petition:
http://petition.eurolinux.org

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to Ard van Breemen

Hello,

Quoted 4 lines · Ard van Breemen

Hi,
Has anybody noticed that when:
ip addr add 192.168.0.1/32 dev eth0
ip route add 192.168.0.2/32 dev eth0

It should respond after "ip route flush cache",
you are missing something, I assume eth0 is not down.

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Ard van Breemen
Quoted 8 lines · Julian Anastasov
Quoted 4 lines · Ard van Breemen

Hi,
Has anybody noticed that when:
ip addr add 192.168.0.1/32 dev eth0
ip route add 192.168.0.2/32 dev eth0

It should respond after "ip route flush cache",

Grrrr, thanks Julian.

Quoted 1 line

you are missing something, I assume eth0 is not down.

Correct. This was just the educational example...
Pfff, I thought I was going insane.... I had a 2.4.18 kernel talking to a 2.4.20 kernel, except that the 2.4.20 kernel did not reply on the arps... Now to find something soft to bounce my head against (I already have the headache, so I don't want it to hurt extra...).

Eh, just curious in how arp depends on routing... I've already seen how neigh/gc_thresh[123] can influence the reachability of a host, and that the routing cache can lock entries in the neigh table while they are being flushed, filling up the neigh table etc...

Signature · 8 lines
mail          up  171+00:12,     7 users,  load 0.08, 0.20, 0.16
mistar1       up   29+18:16,    17 users,  load 0.02, 0.04, 0.00
Let your government know you value your freedom: sign the petition:
http://petition.eurolinux.org

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#5 lore raw
In reply to Ard van Breemen

Hello,

Quoted 5 lines · Ard van Breemen

Eh, just curious in how arp depends on routing... I've already seen how neigh/gc_thresh[123] can influence the reachability of a host, and that the routing cache can lock entries in the neigh table while they are being flushed, filling up the neigh table etc...

When ARP packet is received the ARP code uses "input routing"
lookup (which can return cached entry) to determine what IP is resolved. The result can be "local delivery", "forward", etc but there are additional conditions that determine whether we reply to this probe. In short, ARP follows the IPv4 routing with additional checks.

In your case I assume we already have cached
entry and without flushing it we can not provide actual/valid lookup result. The rule is that if you care, after adding new route you have to flush the cache. After adding IP addresses the flush is automatically performed from the kernel but it is not true for the routes.

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/