Skip to contentSkip to conversation

Artificial latency

LARTC Ryan Agler 2 participants 4 messages Jun 7, 2003 – Jun 10, 2003

lore
Share & tools
lore

Ryan Agler

author
#0 lore raw

I have a situation where I would like to introduce an artificial delay of 100 milliseconds to incoming UDP traffic to a particular client. Here is my setup:

                 +-------+          +-----------+
                 | Linux |          |           |
'Internet'---eth1| NAT   |eth0===|192.168.1.4|
                 |       |          |           |
                 +-------+          +-----------+

Note I'm not looking to restrict the RATE or SPEED at all, just to add a DELAY, and only to incoming UDP packets coming in from the Internet destined for 192.168.1.4. I have kernel 2.4.20 with all the latest and greatest tc, htb patches, etc.

Can anyone help??

Thanks much,
+Ryan

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

hi ryan,

i had asked a similar question a while back, and stef recommended the following:

http://snad.ncsl.nist.gov/itg/nistnet

make sure to read the faq!

cheers

charles

Quoted 17 lines · Ryan Agler

I have a situation where I would like to introduce an artificial delay of 100 milliseconds to incoming UDP traffic to a particular client. Here is my setup:

                 +-------+          +-----------+
                 | Linux |          |           |
'Internet'---eth1| NAT   |eth0===|192.168.1.4|
                 |       |          |           |
                 +-------+          +-----------+

Note I'm not looking to restrict the RATE or SPEED at all, just to add a DELAY, and only to incoming UDP packets coming in from the Internet destined for 192.168.1.4. I have kernel 2.4.20 with all the latest and greatest tc, htb patches, etc.

Can anyone help??

Quoted 7 lines

Thanks much,
+Ryan

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#2 lore raw
In reply to Ryan Agler

Hi Charles,

Thanks for your response! I followed your advice and installed the nistnet kernel module, and after a lot of wrestling it worked.

Ill explain why I need a delay to incoming UDP traffic -- 192.168.1.4 is a Cisco ATA-186 Analog Telephone Adaptor, which lets me hook up a normal phone/fax machine and place calls over the Internet. It turns out that there is a slight asymmetric delay, i.e. the time between when I speak into the phone and its heard by the person I call is longer than the time between her speaking and me hearing it. This is fine for voice, but intolerable to my fax machine. So, I used the nistnet module to delay incoming UDP packets to 192.168.1.4 by 300 milliseconds, and got the 'symmetric' delay I was seeking and faxes are working!

I am wondering if anyone out there can think of another delaying solution
using a qdisc?? I had many problems getting the nistnet module installed;
it refused to coexist with an lt_serial module that allows my faxmodem to work, and causes sporadic fits with my kernel.

Any advice is appreciated!

Thanks,
+Ryan

-----Original Message-----
From: Charles Shick [mailto:[email protected]]
Sent: Sunday, June 08, 2003 4:12 AM
To: Ryan Agler
Subject: Re: [LARTC] Artificial latency

hi ryan,

i had asked a similar question a while back, and stef recommended the following:

http://snad.ncsl.nist.gov/itg/nistnet

make sure to read the faq!

cheers

charles

Quoted 2 lines · Ryan Agler

I have a situation where I would like to introduce an artificial delay of 100 milliseconds to incoming UDP traffic to a particular client. Here is

my

Quoted 10 lines

setup:

                 +-------+          +-----------+
                 | Linux |          |           |
'Internet'---eth1| NAT   |eth0===|192.168.1.4|
                 |       |          |           |
                 +-------+          +-----------+

Note I'm not looking to restrict the RATE or SPEED at all, just to add a DELAY, and only to incoming UDP packets coming in from the Internet

destined

Quoted 1 line

for 192.168.1.4. I have kernel 2.4.20 with all the latest and greatest

tc,

Quoted 11 lines

htb patches, etc.

Can anyone help??

Thanks much,
+Ryan

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Ryan Agler

hello ryan,

Quoted 3 lines

So, I used the nistnet module to delay incoming UDP packets to 192.168.1.4 by 300 milliseconds, and got the 'symmetric' delay I was seeking and faxes are working!

good news, alhtough I am curious how you are connected to the internet? also, did you check with cisco?

Quoted 2 lines

I am wondering if anyone out there can think of another delaying solution using a qdisc??

i am not aware but would also be interested -- please do post back should you find anything ...

Quoted 3 lines

I had many problems getting the nistnet module installed;
it refused to coexist with an lt_serial module that allows my faxmodem to work, and causes sporadic fits with my kernel.

yes, i experienced similar issues, but managed to get it stable for some very simple testing -- i need to do more.

cheerio

charles

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/