Skip to contentSkip to conversation

borrowing+priority, help req

LARTC [email protected] 2 participants 2 messages Jul 24, 2003 – Jul 28, 2003

lore
Share & tools
lore
#0 lore raw

Hi!

I'm new to this list :) I have a problem (or misunderstanding) trying to set up the very basic example: giving priority to outgoing traffic from a host (on 100Mbit Ethernet) towards a subset of nodes based on their IP address (not on QoS flags), while allowing others to use all 'leftover' bandwidth.

I have tried with htb and cbq qdiscs as well and neither seems to be doing what I want. :) Here is my CBQ setup:

tc qdisc add dev eth1 root handle 1:0 cbq bandwidth 100Mbit \

	 rate 100Mbit avpkt 1000 cell 8

tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 100Mbit rate 100Mbit \
weight 1Mbit prio 8 allot 1514 cell 8 maxburst 20 avpkt 1000 bounded
tc class add dev eth1 parent 1:1 classid 1:3 cbq bandwidth 100Mbit rate 80Mbit \
weight 0.8Mbit prio 5 allot 1514 cell 8 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:4 cbq bandwidth 100Mbit rate 20Mbit \
weight 0.2Mbit prio 5 allot 1514 cell 8 maxburst 20 avpkt 1000
tc qdisc add dev eth1 parent 1:3 handle 30: sfq
tc qdisc add dev eth1 parent 1:4 handle 40: sfq
tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match \

	ip dst 10.0.0.0/16 flowid 1:3
tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match \
	ip dst 10.1.0.0/16 flowid 1:4

What this simply does for me is that when both IP ranges start 'fighting' for bandwidth they get about 50% each while as I understood (? :) from the HOWTO they should have got a 8:2 ratio.
If I make one of 1:3 or 1:4 'bounded', the other is able to borrow its bandwidth, but not the other way around (no surprise).

I tried the prio qdisc too:

tc qdisc add dev eth1 root handle 1: prio
tc qdisc add dev eth1 parent 1:1 handle 10: sfq perturb 10 tc qdisc add dev eth1 parent 1:2 handle 20: sfq perturb 10 tc qdisc add dev eth1 parent 1:3 handle 30: sfq perturb 10 tc filter add dev eth1 parent 1: protocol ip prio 1 u32 match \

	ip dst 10.1.0.0/16 flowid 1:3
tc filter add dev eth1 parent 1: protocol ip prio 1 u32 match \
	 ip dst 10.0.0.0/16 flowid 1:1

which seems to have 'no effect' as well (50% bandwidth goes to both parties).

The packets indeed make it to the right class/qdisc according to tc -s. Measurements were taken using iptables counters.

Could you help me (either by pointing out where I don't understand something or providing a working example)?

Thanks a lot in advance,
Andras
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 44 lines · On Thursday 24 July 2003 09:19, [email protected] wrote:

Hi!

I'm new to this list :) I have a problem (or misunderstanding) trying to set up the very basic example: giving priority to outgoing traffic from a host (on 100Mbit Ethernet) towards a subset of nodes based on their IP address (not on QoS flags), while allowing others to use all 'leftover' bandwidth.

I have tried with htb and cbq qdiscs as well and neither seems to be doing what I want. :) Here is my CBQ setup:

tc qdisc add dev eth1 root handle 1:0 cbq bandwidth 100Mbit \

	 rate 100Mbit avpkt 1000 cell 8

tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 100Mbit rate 100Mbit \ weight 1Mbit prio 8 allot 1514 cell 8 maxburst 20 avpkt 1000 bounded tc class add dev eth1 parent 1:1 classid 1:3 cbq bandwidth 100Mbit rate 80Mbit \ weight 0.8Mbit prio 5 allot 1514 cell 8 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:4 cbq bandwidth 100Mbit rate 20Mbit \ weight 0.2Mbit prio 5 allot 1514 cell 8 maxburst 20 avpkt 1000 tc qdisc add dev eth1 parent 1:3 handle 30: sfq
tc qdisc add dev eth1 parent 1:4 handle 40: sfq
tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match \

	ip dst 10.0.0.0/16 flowid 1:3
tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match \
	ip dst 10.1.0.0/16 flowid 1:4

What this simply does for me is that when both IP ranges start 'fighting' for bandwidth they get about 50% each while as I understood (? :) from the HOWTO they should have got a 8:2 ratio.
If I make one of 1:3 or 1:4 'bounded', the other is able to borrow its bandwidth, but not the other way around (no surprise).

I tried the prio qdisc too:

tc qdisc add dev eth1 root handle 1: prio
tc qdisc add dev eth1 parent 1:1 handle 10: sfq perturb 10 tc qdisc add dev eth1 parent 1:2 handle 20: sfq perturb 10 tc qdisc add dev eth1 parent 1:3 handle 30: sfq perturb 10 tc filter add dev eth1 parent 1: protocol ip prio 1 u32 match \

	ip dst 10.1.0.0/16 flowid 1:3
tc filter add dev eth1 parent 1: protocol ip prio 1 u32 match \
	 ip dst 10.0.0.0/16 flowid 1:1
Quoted 8 lines

which seems to have 'no effect' as well (50% bandwidth goes to both parties).

The packets indeed make it to the right class/qdisc according to tc -s. Measurements were taken using iptables counters.

Could you help me (either by pointing out where I don't understand something or providing a working example)?

See docum.org for examples.
You can try to shape your total bandwidth to 95mbit. So YOU are the
bottleneck and not the network.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/