ARP Help (was - [LARTC] snooping - plan B)
Thanks for the help from the list so far. It's now reduced to an ARP problem.
host0
192.168.253.1----snoopy(eth0 192.168.253.254)
Now ping 192.168.253.2 and get snoopy to respond. This can be done with netfilter (but not, apparently with ip).
iptables -A PREROUTING -t nat -p icmp -d 192.168.253.2 -j DNAT --to 192.168.253.254/sbin/arp -i eth0 -Ds 192.168.253.2 eth0 pub
gets you a "host unreachable" from 192.168.253.1
BUT if on host0 you:
/sbin/arp -s 192.168.253.2 HWADDR
then ping goes through.
Help from ARP experts (or others!) much appreciated.
Jim
Quoted 98 lines · Martin A. Brown
Jim,
First, let me say that I may not have caught all of your plan...but here
goes....If you really wish to modify application layer data, shouldn't you be looking at divert sockets [1], tun/tap usage [2], or optimally home-grown
code?: OK, assuming this to be impossible. Let's try the ARP approach. I : want to set up eth0 with ip 192.168.3.1 nat all packet addressed to : 192.168.1.1 to 192.168.3.1 and ARP the address of 192.168.1.1 into : eth0. I still have some problems, any suggestions appreciated. : Here's what I've tried (along with many variations):
Hmmmmm.... I haven't ever tried to do exactly what you seem to suggest
here, but this may be an interesting approach. If you are going to use
NAT to solve your problem, you can try NATting each host into the other.: arp -i eth0 -Ds 192.168.1.1 eth0 pub
: ip route add nat 192.168.1.1 via 192.168.3.1
: ip rule add from 192.168.3.1 nat 192.168.1.1[ Note: I'm using the IP ranges you suggested in a prior mail. ]
host-0 +--------+ host-1
192.168.253.1 <--> eth0 <-- snoopy --> eth1 <--> 192.168.253.2+--------+Assuming that you want host-0 to reach host-1, but only through snoopy,
and you don't want to alter any network addressing on either host-0 or host-1:# ip route add 192.168.253.1 dev eth0 # ip route add 192.168.253.2 dev eth1 # ip route add nat 192.168.253.102 via 192.168.253.2 iif eth0 # ip rule add nat 192.168.253.102 from 192.168.253.2 iif eth1 # ip route add nat 192.168.253.101 via 192.168.253.1 iif eth1 # ip rule add nat 192.168.253.101 from 192.168.253.1 iif eth0The nat route entry in the local routing table will take care of the ARP
advertising for you, so any packets from host-0 addressed to 192.168.253.102 should end up on 192.168.253.2, but with a source address
of 192.168.253.101.So, a packet from host-0 to host-1 will look like this....
host-0 side of snoopy host-1 side of
Source: 192.168.253.1 192.168.253.101
Dest: 192.168.253.102 192.168.253.2To me, this looks terribly convoluted and rather messy, not to mention that I have never tried it! Nonetheless, I think this should work, provided that the nat IPs you choose are not in use anywhere else in your
192.168.253.0/24 network.: this alone is not sufficient, so I've tried adding routes for : 192.168.1.1
: ip route add 192.168.1.1 dev eth0
: and so forth. I haven't yet been successful and would apprciate
any
: help.Now, if I might make another recommendation....
Take a look at bridging [3]. This project has been maturing very nicely,
and there have been very happy rumbles from people using the linux bridging code. With the help of IP mode [4], you may get the control you
desire. Also look at the bridge + firewall documentation [5] and make sure to fetch the br+nf patches if you are using a 2.4 kernel [6].Good luck,
-Martin
[1] http://152.45.4.41/~divert/index.shtml [2] http://vtun.sourceforge.net/tun/ [3] http://bridge.sourceforge.net/ [4] http://www.ssi.bg/~ja/bridging.txt [5] http://ebtables.sourceforge.net/br_fw_ia/br_fw_ia.html [6] http://sourceforge.net/projects/ebtables/--
Martin A. Brown --- SecurePipe, Inc. --- [email protected]
Signature · 6 lines
Jim Redman (505) 662 5156 x85 http://www.ergotech.com _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Jim,
I must be uncommonly dense, because I still haven't a clue what you are trying to do. I'll take one last stab at it, though.
: host0
: 192.168.253.1----snoopy(eth0 192.168.253.254)
:
: Now ping 192.168.253.2 and get snoopy to respond. This can be done : with netfilter (but not, apparently with ip).
Accurate, as far as I know.
: iptables -A PREROUTING -t nat -p icmp -d 192.168.253.2 -j DNAT --to 192.168.253.254
Sure.
: /sbin/arp -i eth0 -Ds 192.168.253.2 eth0 pub : gets you a "host unreachable" from 192.168.253.1
Have you tried this?
arp -s 192.168.253.2 -i eth0 -D eth0 pub
Sadly, /sbin/arp (at least on my test boxen) seems to be persnickety about the order of arguments and options.
: BUT if on host0 you:
: /sbin/arp -s 192.168.253.2 HWADDR
:
: then ping goes through.
: Help from ARP experts (or others!) much appreciated.
If you really wish to get your hands dirty with ARP, you can always have ultimate control with "ip arp", a kernel + iproute2 patch.
Bonne chance,
-Martin
Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/