Bandwidth Monitor
Anybody knows about one bandwidth meter to use in Bering. This is a script i built, it's works wel, but it's not very nice!!! =P
#!/bin/bash
# Bandwidth Monitor
device=eth0
bytes=grep $device /proc/net/dev | cut -f 2 -d : | cut -d ' ' -f 2 kbytes=expr $bytes / 1024
actual=$kbytes
i=1
x=0
total=0
while [ $i -le 2 ]
do
x=`expr $x + 1`
bytes=`grep $device /proc/net/dev | cut -f 2 -d : | cut -d ' ' -f 2`
kbytes=`expr $bytes / 1024`
valor=`expr $kbytes - $actual`
actual=$kbytes
if [ $x = 5 ]
then
x=2
total=$promedio
fi
total=`expr $total + $valor`
promedio=`expr $total / $x`
echo actual: [$valor Kb/s] - promedio: [$promedio Kb/s]
sleep 1done
Best regards.
Sebastián A. Aresca
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi,
Have a look at
http://ldp.kernelnotes.de/HOWTO/Querying-libiptc-HOWTO/bmeter.html
Best regards,
Leonardo Balliache
Quoted 38 lines · you
Anybody knows about one bandwidth meter to use in Bering. This is a script i built, it's works wel, but it's not very nice!!! =P
#!/bin/bash
# Bandwidth Monitor
device=eth0
bytes=
grep $device /proc/net/dev | cut -f 2 -d : | cut -d ' ' -f 2kbytes=expr $bytes / 1024
actual=$kbytesi=1
x=0
total=0
while [ $i -le 2 ]
dox=`expr $x + 1` bytes=`grep $device /proc/net/dev | cut -f 2 -d : | cut -d ' ' -f 2` kbytes=`expr $bytes / 1024` valor=`expr $kbytes - $actual` actual=$kbytes if [ $x = 5 ] then x=2 total=$promedio fi total=`expr $total + $valor` promedio=`expr $total / $x` echo actual: [$valor Kb/s] - promedio: [$promedio Kb/s] sleep 1done
Quoted 7 lines
Best regards.
Sebastián A. Aresca
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Practical QoS
http://opalsoft.net/qos
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 1 line · On Fri, 1 Aug 2003, [iso-8859-1] Sebastián Aresca wrote:
Anybody knows about one bandwidth meter to use in Bering.
You might want give nanotop a try. It shows a line like this:
CPU: [=- ] MEM: 8.8MB LAN: 1.0kB/s(RX) 454.00B/s(TX) 0(ERR
Dynamically built and stripped, the executable file size is about 5k.
The home page:
http://floppyfw.wojci.dk/nanotop.phtml
Cheers,
Cristian
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/