Skip to contentSkip to conversation

Question about subclasses and filters

LARTC Tilman Giese 2 participants 2 messages Aug 3, 2003

lore
Share & tools
lore
#0 lore raw

Hi,

unfortunately I did not get any response to my last message, so let me describe my problem in detail.

I am setting up a router that is responsible for four different offices like shown below:

                |--- Office 1 (192.168.100.242)
                |
   __________   |--- Office 2 (192.168.100.243)
---| Router |---|
   ----------   |--- Office 3 (192.168.100.244)
                |
                |--- Office 4 ------- 192.168.100.245
                                 |
                                 |--- 192.168.100.246
                                 |
                                 |--- 192.168.100.247

Each office should have one fourth of the available bandwidth, but can borrow bandwidth if necessary. 192.168.0.246 in Office 4 is something special. This server should have a maximum of one fourth.

Therefore I created the following classes:

# queuing discipline
tc qdisc add dev eth1 root handle 1: cbq bandwidth 2MBit allot 1514 cell 
8 avpkt 1000 mpu 64
# root class
tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 2MBit rate 
2MBit allot 1514 cell 8 weight 200KBit prio 5 maxburst 20 avpkt 1000
# offices
tc class add dev eth1 parent 1:1 classid 1:2 cbq bandwidth 2MBit rate 
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:3 cbq bandwidth 2MBit rate 
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:4 cbq bandwidth 2MBit rate 
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:5 cbq bandwidth 2MBit rate 
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000

# Special treatment for 192.168.100.246
tc qdisc add dev eth1 parent 1:5 handle 2: cbq bandwidth 512KBit allot 1514 cell 8 avpkt 1000 mpu 64
tc class add dev eth1 parent 2:0 classid 2:1 cbq bandwidth 512KBit rate 512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000 tc class add dev eth1 parent 2:1 classid 2:2 cbq bandwidth 512KBit rate 128KBit allot 1514 cell 8 weight 12KBit prio 5 maxburst 20 avpkt 1000

Then I added the following filters:

tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.242 flowid 1:2
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.243 flowid 1:3
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.244 flowid 1:4
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.245 flowid 1:5
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.247 flowid 1:5

# Special treatment for 192.168.100.246
tc filter add dev eth1 parent 2:0 prio 5 protocol ip u32 tc filter add dev eth1 parent 2:0 prio 5 protocol ip u32 match ip dst 192.168.100.246 flowid 2:2

Everything okay up to here. But then I looked ar the following:

# tc -s class show dev eth1

class cbq 2: root rate 512Kbit (bounded,isolated) prio no-transmit
Sent 261534164 bytes 433080 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 12499 undertime 0
class cbq 2:1 parent 2: rate 512Kbit prio 5
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 12499 undertime 0
class cbq 2:2 parent 2:1 rate 128Kbit prio 5
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.13741e+06 undertime 0
class cbq 1: root rate 2Mbit (bounded,isolated) prio no-transmit
Sent 142271650091 bytes 210353356 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 3124 undertime 0
class cbq 1:1 parent 1: rate 2Mbit prio no-transmit
Sent 2136522126 bytes 2961604 pkts (dropped 0, overlimits 0)
borrowed 432995 overactions 0 avgidle 3124 undertime 0
class cbq 1:2 parent 1:1 rate 512Kbit prio 5
Sent 6450824 bytes 12703 pkts (dropped 0, overlimits 0)
borrowed 7022 overactions 0 avgidle 282608 undertime 0
class cbq 1:3 parent 1:1 rate 512Kbit prio 5
Sent 1846942719 bytes 2448726 pkts (dropped 0, overlimits 0)
borrowed 420044 overactions 0 avgidle 284352 undertime 0
class cbq 1:4 parent 1:1 rate 512Kbit prio 5
Sent 21594419 bytes 67095 pkts (dropped 0, overlimits 0)
borrowed 5312 overactions 0 avgidle 284352 undertime 0
class cbq 1:5 parent 1:1 leaf 2: rate 512Kbit prio 5
Sent 261534164 bytes 433080 pkts (dropped 0, overlimits 0)
borrowed 617 overactions 0 avgidle 284352 undertime 0

Now I have two questions.

1. Why is the package count of class 2:0 equal to the one of class 1:5?
2. Why are there no packets in class 2:2 and 2:1 respectively?

It would be nice if someone could help me or show me a place where I can find an answer to my questions.

Thanks in advance.

Tilman Giese

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 103 lines · Tilman Giese

Hi,

unfortunately I did not get any response to my last message, so let me describe my problem in detail.

I am setting up a router that is responsible for four different offices

like shown below:

                |--- Office 1 (192.168.100.242)
   __________   |--- Office 2 (192.168.100.243)
---| Router |---|
   ----------   |--- Office 3 (192.168.100.244)
                |--- Office 4 ------- 192.168.100.245
                |
                                 |--- 192.168.100.246
                                 |
                                 |--- 192.168.100.247

Each office should have one fourth of the available bandwidth, but can borrow bandwidth if necessary. 192.168.0.246 in Office 4 is something special. This server should have a maximum of one fourth.

Therefore I created the following classes:

# queuing discipline
tc qdisc add dev eth1 root handle 1: cbq bandwidth 2MBit allot 1514 cell
8 avpkt 1000 mpu 64
# root class
tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 2MBit rate
2MBit allot 1514 cell 8 weight 200KBit prio 5 maxburst 20 avpkt 1000
# offices
tc class add dev eth1 parent 1:1 classid 1:2 cbq bandwidth 2MBit rate
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:3 cbq bandwidth 2MBit rate
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:4 cbq bandwidth 2MBit rate
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000
tc class add dev eth1 parent 1:1 classid 1:5 cbq bandwidth 2MBit rate
512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000

# Special treatment for 192.168.100.246
tc qdisc add dev eth1 parent 1:5 handle 2: cbq bandwidth 512KBit allot 1514 cell 8 avpkt 1000 mpu 64
tc class add dev eth1 parent 2:0 classid 2:1 cbq bandwidth 512KBit rate 512KBit allot 1514 cell 8 weight 50KBit prio 5 maxburst 20 avpkt 1000 tc class add dev eth1 parent 2:1 classid 2:2 cbq bandwidth 512KBit rate 128KBit allot 1514 cell 8 weight 12KBit prio 5 maxburst 20 avpkt 1000

Then I added the following filters:

tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.242 flowid 1:2
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.243 flowid 1:3
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.244 flowid 1:4
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.245 flowid 1:5
tc filter add dev eth1 parent 1:0 prio 5 protocol ip u32 match ip dst 192.168.100.247 flowid 1:5

# Special treatment for 192.168.100.246
tc filter add dev eth1 parent 2:0 prio 5 protocol ip u32 tc filter add dev eth1 parent 2:0 prio 5 protocol ip u32 match ip dst 192.168.100.246 flowid 2:2

Everything okay up to here. But then I looked ar the following:

# tc -s class show dev eth1

class cbq 2: root rate 512Kbit (bounded,isolated) prio no-transmit
Sent 261534164 bytes 433080 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 12499 undertime 0
class cbq 2:1 parent 2: rate 512Kbit prio 5
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 12499 undertime 0
class cbq 2:2 parent 2:1 rate 128Kbit prio 5
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.13741e+06 undertime 0
class cbq 1: root rate 2Mbit (bounded,isolated) prio no-transmit
Sent 142271650091 bytes 210353356 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 3124 undertime 0
class cbq 1:1 parent 1: rate 2Mbit prio no-transmit
Sent 2136522126 bytes 2961604 pkts (dropped 0, overlimits 0)
borrowed 432995 overactions 0 avgidle 3124 undertime 0
class cbq 1:2 parent 1:1 rate 512Kbit prio 5
Sent 6450824 bytes 12703 pkts (dropped 0, overlimits 0)
borrowed 7022 overactions 0 avgidle 282608 undertime 0
class cbq 1:3 parent 1:1 rate 512Kbit prio 5
Sent 1846942719 bytes 2448726 pkts (dropped 0, overlimits 0)
borrowed 420044 overactions 0 avgidle 284352 undertime 0
class cbq 1:4 parent 1:1 rate 512Kbit prio 5
Sent 21594419 bytes 67095 pkts (dropped 0, overlimits 0)
borrowed 5312 overactions 0 avgidle 284352 undertime 0
class cbq 1:5 parent 1:1 leaf 2: rate 512Kbit prio 5
Sent 261534164 bytes 433080 pkts (dropped 0, overlimits 0)
borrowed 617 overactions 0 avgidle 284352 undertime 0

Quoted 3 lines

Now I have two questions.

1. Why is the package count of class 2:0 equal to the one of class 1:5?

Because all packets entering class 1:5 are queued in the qdisc attached to that class. And that qdisc is 2:0.

Quoted 1 line

2. Why are there no packets in class 2:2 and 2:1 respectively?

You have a filter that puts packets from 2:0 to 2:2 if the dst address is X.X.X.246. But you never put these packets in the 2:0 qdisc ... So you have to add that filter to 1:0 and not to 2:0.

And some other remarks. Bandwidth is the real NIC bandwidth. So 10mbit or 100mbit. And you have to bound class 1:1 so the child classes can share the bandwidth.
And why do you add the qdisc 2:0? You can do this also with classes. A cbq qdisc to a cbq class is never a good idea.

Quoted 2 lines

It would be nice if someone could help me or show me a place where I can find an answer to my questions.

http://www.docum.org

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/