CBQ_bandwidth
Hi Stef,
Reffering to page < http://www.docum.org/stef.coene/qos/faq/cache/7.html
Quoted 1 line
I found a para as follows,
" CBQ is not always as accurate as it should be. See docum.org on the test page for some tests with bounded classes. The algorithm used by cbq is very "link sensitive". It calculates the link idle time and for that it needs the real link bandwidth, average packet size and some other parameters. But there calculations are not always accurate. So it's possible that you will get inaccurate results if you use CBQ to limit the traffic in a class. "
Here Iam slightly confused with real link bandwidth, Can I understand that while creating CBQ we need interface bandwidth (ethtool, mii-diag) and and while assigning the classes real link bandwidth is required. An example will definately help me. Can you pls suggest a way to find real link bandwidth....? As ethtool and mii-diag will only get the interface bandwidth.
Regards
-Raghu
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 14 lines · Raghuveer
Hi Stef,
Reffering to page < http://www.docum.org/stef.coene/qos/faq/cache/7.html
Quoted 1 line
I found a para as follows,
" CBQ is not always as accurate as it should be. See docum.org on the test page for some tests with bounded classes. The algorithm used by cbq is very "link sensitive". It calculates the link idle time and for that it needs the real link bandwidth, average packet size and some other parameters. But there calculations are not always accurate. So it's possible that you will get inaccurate results if you use CBQ to limit the traffic in a class. "
Quoted 6 lines
Here Iam slightly confused with real link bandwidth, Can I understand that while creating CBQ we need interface bandwidth (ethtool, mii-diag) and and while assigning the classes real link bandwidth is required. An example will definately help me. Can you pls suggest a way to find real link bandwidth....? As ethtool and mii-diag will only get the interface bandwidth.
The bandwidth parameter is the real link bandwidth like ethtook or mii-diag will show you.
If you want to limit all traffic to the link bandwidth, you have to create a class that's bounded and with rate = link bandwidth. You can create non-bounded sub classes but the bandwidth will be limit by the bounded class to the link bandwidth.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 25 lines · Stef Coene
Quoted 14 lines · Raghuveer
Hi Stef,
Reffering to page < http://www.docum.org/stef.coene/qos/faq/cache/7.html
Quoted 1 line
I found a para as follows,
" CBQ is not always as accurate as it should be. See docum.org on the test page for some tests with bounded classes. The algorithm used by cbq is very "link sensitive". It calculates the link idle time and for that it needs the real link bandwidth, average packet size and some other parameters. But there calculations are not always accurate. So it's possible that you will get inaccurate results if you use CBQ to limit the traffic in a class. "
Quoted 8 lines
Here Iam slightly confused with real link bandwidth, Can I understand that while creating CBQ we need interface bandwidth (ethtool, mii-diag) and and while assigning the classes real link bandwidth is required. An example will definately help me. Can you pls suggest a way to find real link bandwidth....? As ethtool and mii-diag will only get the interface bandwidth.
Quoted 8 lines
The bandwidth parameter is the real link bandwidth like ethtook or mii-diag will show you.
If you want to limit all traffic to the link bandwidth, you have to create a class that's bounded and with rate = link bandwidth. You can create non-bounded sub classes but the bandwidth will be limit by the bounded class to the link bandwidth.
What is confusing me is, there is a bandwidth provided by ISP (512Kbits) and one ethernet capacity(100Mbits), so which one can we call as real link bandwidth. What is NIC bandwidth....is it ethernet bandwidth or ISP bandwidth....?
Lan------->eth1-----------eth0---------->Internet
Now at eth0 I have ethernet device bandwidth as 100Mbits and my ISP provides 512Kbits bandwidth. so if I want to do egress traffic control at both eth0 and eth1, what bandwidth I should consider...? My eth1 ethernet device bandwidth is 100Mbits.
Regards
-Raghu
Quoted 4 lines
Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 9 lines · Raghuveer
What is confusing me is, there is a bandwidth provided by ISP (512Kbits) and one ethernet capacity(100Mbits), so which one can we call as real link bandwidth. What is NIC bandwidth....is it ethernet bandwidth or ISP bandwidth....?
Lan------->eth1-----------eth0---------->InternetNow at eth0 I have ethernet device bandwidth as 100Mbits and my ISP provides 512Kbits bandwidth. so if I want to do egress traffic control at both eth0 and eth1, what bandwidth I should consider...? My eth1 ethernet device bandwidth is 100Mbits.
What bout this :
for all cbq commands : bandwidth 100mbit
eth0
cbq qdisc
cbq class rate = 512kbit, bounded
cbq class 1, rate < 512kbit
cbq class ..., rate < 512kbit
cbq class x, rate < 512kbit
So all traffic from class 1 ... x togehter is bounded to 512kbit.
eth1
cbq qdisc
cbq class rate = 100mbit, bounded
cbq class 1, rate 512kbit bounded
cbq class 10, rate < 512kbit
cbq class ..., rate < 512kbit
cbq class x, rate < 512kbit
cbq class 2, rate 99,5Mbit
cbq class 20, rate < 99,5Mbit
cbq class ..., rate < 99,5Mbit
cbq class x, rate < 99,5Mbit
Class 1 is for all traffic from internet -> LAN
Class 2 is for all traffic from shaper -> LAN
And if you really want to be sure it's working, you should take 500kbit. So YOU are the bottleneck and in control of the link and not the modem.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 37 lines · Stef Coene
Quoted 11 lines · Raghuveer
What is confusing me is, there is a bandwidth provided by ISP (512Kbits) and one ethernet capacity(100Mbits), so which one can we call as real link bandwidth. What is NIC bandwidth....is it ethernet bandwidth or ISP bandwidth....?
Lan------->eth1-----------eth0---------->Internet
Now at eth0 I have ethernet device bandwidth as 100Mbits and my ISP provides 512Kbits bandwidth. so if I want to do egress traffic control at both eth0 and eth1, what bandwidth I should consider...? My eth1 ethernet device bandwidth is 100Mbits.What bout this :
for all cbq commands : bandwidth 100mbit
eth0
cbq qdisc
cbq class rate = 512kbit, bounded
cbq class 1, rate < 512kbit
cbq class ..., rate < 512kbit
cbq class x, rate < 512kbit
So all traffic from class 1 ... x togehter is bounded to 512kbit.eth1
cbq qdisc
cbq class rate = 100mbit, bounded
cbq class 1, rate 512kbit bounded
cbq class 10, rate < 512kbit
cbq class ..., rate < 512kbit
cbq class x, rate < 512kbit
cbq class 2, rate 99,5Mbit
cbq class 20, rate < 99,5Mbit
cbq class ..., rate < 99,5Mbit
cbq class x, rate < 99,5Mbit
Quoted 7 lines
Class 1 is for all traffic from internet -> LAN
Class 2 is for all traffic from shaper -> LANAnd if you really want to be sure it's working, you should take 500kbit. So YOU are the bottleneck and in control of the link and not the modem.
Thanks alot Stef, Its very clear to me now.
If I have ADSL with different incoming and outgoing rates. For egress shaping at WAN(eth0) interface, Whether should I use outgoing rates or combined rates (incomming + outgoing). Will it make any big difference if I use combined rates in an asymmetric link like cabel modem, ADSL etc.
Regards
-Raghu
Quoted 4 lines
Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 5 lines · Raghuveer
Thanks alot Stef, Its very clear to me now.
If I have ADSL with different incoming and outgoing rates. For egress shaping at WAN(eth0) interface, Whether should I use outgoing rates or combined rates (incomming + outgoing). Will it make any big difference if I use combined rates in an asymmetric link like cabel modem, ADSL etc.
At eth0, you should take outgoing rates. And this can be assymetric from incoming rates. Why not ?
I didn't knew your incoming and outgoing rates so I just took 512kbit for incoming and outgoing.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 10 lines · Stef Coene
Quoted 7 lines · Raghuveer
Thanks alot Stef, Its very clear to me now.
If I have ADSL with different incoming and outgoing rates. For egress shaping at WAN(eth0) interface, Whether should I use outgoing rates or combined rates (incomming + outgoing). Will it make any big difference if I use combined rates in an asymmetric link like cabel modem, ADSL etc.
Quoted 6 lines
At eth0, you should take outgoing rates. And this can be assymetric from incoming rates. Why not ?
I didn't knew your incoming and outgoing rates so I just took 512kbit for incoming and outgoing.
How can I get the incomming and outgoing rates seperately ...?
Regards
-Raghu
Quoted 4 lines
Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 8 lines · Raghuveer
Quoted 7 lines · Stef Coene
Quoted 5 lines · Raghuveer
Thanks alot Stef, Its very clear to me now.
If I have ADSL with different incoming and outgoing rates. For egress shaping at WAN(eth0) interface, Whether should I use outgoing rates or combined rates (incomming + outgoing). Will it make any big difference if I use combined rates in an asymmetric link like cabel modem, ADSL etc.
Quoted 6 lines
Quoted 4 lines
At eth0, you should take outgoing rates. And this can be assymetric from incoming rates. Why not ?
I didn't knew your incoming and outgoing rates so I just took 512kbit for incoming and outgoing.How can I get the incomming and outgoing rates seperately ...?
What do you mean? How to configure htb or how to get these numbers from you ISP?
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 22 lines · Stef Coene
Quoted 19 lines · Raghuveer
Quoted 16 lines · Stef Coene
Quoted 7 lines · Raghuveer
Thanks alot Stef, Its very clear to me now.
If I have ADSL with different incoming and outgoing rates. For egress shaping at WAN(eth0) interface, Whether should I use outgoing rates or combined rates (incomming + outgoing). Will it make any big difference if I use combined rates in an asymmetric link like cabel modem, ADSL etc.At eth0, you should take outgoing rates. And this can be assymetric from incoming rates. Why not ?
I didn't knew your incoming and outgoing rates so I just took 512kbit for incoming and outgoing.
Quoted 6 lines
Quoted 3 lines
How can I get the incomming and outgoing rates seperately ...?
What do you mean? How to configure htb or how to get these numbers from you ISP?
Actually I wanted to know whether is there any way to get the incoming and outgoing rates using some tool.
Regards
-Raghu
Quoted 5 lines
Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 2 lines · Raghuveer
Actually I wanted to know whether is there any way to get the incoming and outgoing rates using some tool.
The rate is (most of the time) limited in the modem. And there is no way you can find this. You can try to upload / download a file to / from a fast ftp server and monitor the bandwidth you get, but that's not very accurate. Even if you don't know the bandwidth, you can shape the traffic.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/