Skip to contentSkip to conversation

Linux router configuration??

LARTC Blu 8 participants 9 messages Sep 25, 2003 – Oct 1, 2003

lore
Share & tools
lore

Blu

author
#0 lore raw

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do? Thanks.

#1 lore raw
Quoted 3 lines · Blu

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do?

That's a pretty vague question, so I'll give you a vague answer:

Get any linux distribution and do a minimum install. Setup the network cards and interfaces. setup the routes and/or routing daemons (setup the firewalling)

In the popular distros, most of these steps are done for you in the install.

good luck.

Signature · 11 lines
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Damion de Soto - Software Engineer  email:     [email protected]
SnapGear ---                           ph:         +61 7 3435 2809
  | Custom Embedded Solutions          fax:         +61 7 3891 3630
  | and Security Appliances            web: http://www.snapgear.com
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  ---  Free Embedded Linux Distro at   http://www.snapgear.org  ---

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Blu

I'll be a tad more helpful, but not much. Setting up a linux firewall/router is pretty specific to your network layout/configuration. You probably will be better off checking these links and going from there:

General Linux setup/config documentation:
http://www.tldp.org

This document is a bit dated in that it doesnt include iptables as one of the firewalling software options, but it still is better than nothing.
http://www.tldp.org/HOWTO/Firewall-HOWTO.html

The HOWTO at http://www.lartc.org is good too (hehe, had to give kudos)

Hope it helps!
Derek

Quoted 12 lines · Damion de Soto
Quoted 3 lines · Blu

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do?

That's a pretty vague question, so I'll give you a vague answer:

Get any linux distribution and do a minimum install. Setup the network cards and interfaces. setup the routes and/or routing daemons (setup the firewalling)

Quoted 4 lines

In the popular distros, most of these steps are done for you in the install.

good luck.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Blu

www.netfilter.org has up to date Kernel 2.4 firewall concepts. The links are also pretty good at describing how everything works if you can't find what you need at the site itself.

-----Original Message-----
From: Derek [mailto:[email protected]]
Sent: Thursday, September 25, 2003 4:40 PM
To: Blu
Cc: [email protected]
Subject: Re: [LARTC] Linux router configuration??

I'll be a tad more helpful, but not much. Setting up a linux firewall/router
is pretty specific to your network layout/configuration. You probably will be
better off checking these links and going from there:

General Linux setup/config documentation:
http://www.tldp.org

This document is a bit dated in that it doesnt include iptables as one of the
firewalling software options, but it still is better than nothing.
http://www.tldp.org/HOWTO/Firewall-HOWTO.html

The HOWTO at http://www.lartc.org is good too (hehe, had to give kudos)

Hope it helps!
Derek

Quoted 2 lines · Damion de Soto
Quoted 1 line · Blu

Good morning at all, thanks for previous help, but I have another

ask. I

Quoted 1 line
Quoted 1 line

have a few experience of Linux world's, and I need to configure a

Linux

Quoted 9 lines
Quoted 1 line

PC as router, what are the steps? What do I do?

That's a pretty vague question, so I'll give you a vague answer:

Get any linux distribution and do a minimum install. Setup the network cards and interfaces. setup the routes and/or routing daemons (setup the firewalling)

Quoted 4 lines

In the popular distros, most of these steps are done for you in the install.

good luck.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Blu

I am going to assume you want the most basic router, just two interfaces.

1.) Make sure both network cards have been detected.
ifconfig eth0
ifconfig eth1
2.) Set up each interface on its own network, make sure the interface has been activated, you can use ifconfig for this. 3.) issue the command
echo 1 > /proc/sys/net/ipv4/ip_forward
to enable ip fowarding, w/o this the kernel will not send packets between interfaces
4.) set the clients behind the router to point to the internal ip of your router

Any changes made to the system will have to be initialized during the boot process.

Of course if you have ip addresses that you would like to nat/masq behind the router, you will have to use iptables.

You really should be more specific on your needs.

Good luck.

Quoted 2 lines

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do? Thanks.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#5 lore raw
In reply to Blu
Quoted 4 lines · Blu

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do? Thanks.

what you could do is.
go to http://leaf.sf.net

this is a router/firewall on a floppy disk system, that also can boot from hd, flash, cd, or whatever.

it's dead easy to setup. reboots very quickly. and only uses media on boot so you wont wear out you'r floppy, hd, cd whatever on constant spinning.

best regards

Signature · 5 lines
Ronny Aasen <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#6 lore raw
In reply to Blu
Quoted 6 lines · Ryan Johnson

I am going to assume you want the most basic router, just two interfaces.

1.) Make sure both network cards have been detected. ifconfig eth0
ifconfig eth1

Can I have both the network cards in the same n/w...? Becoz If I try to use both NIC's with the same n/w, running <$ route -n> we can see either eth1 or eth0 repeated twice. Pls let me know where is the problem..?

Regards
-Raghu

Quoted 17 lines

2.) Set up each interface on its own network, make sure the interface has been activated, you can use ifconfig for this. 3.) issue the command
echo 1 > /proc/sys/net/ipv4/ip_forward
to enable ip fowarding, w/o this the kernel will not send packets between interfaces
4.) set the clients behind the router to point to the internal ip of your router

Any changes made to the system will have to be initialized during the boot process.

Of course if you have ip addresses that you would like to nat/masq behind the router, you will have to use iptables.

You really should be more specific on your needs.

Good luck.

Quoted 11 lines
Quoted 4 lines

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do? Thanks.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#7 lore raw
In reply to Blu
Quoted 3 lines · Raghuveer

Can I have both the network cards in the same n/w...? Becoz If I try to use both NIC's with the same n/w, running <$ route -n> we can see either eth1 or eth0 repeated twice. Pls let me know where is the problem..?

you don't need to do this. just add both IP addresses to the same NIC, viz ;

ip address add 192.168.0.254/24 dev eth0
ip address add 10.128.254.254/16 dev eth0

and proceed as usual. The subnet routes are added automatically.

/steve

#8 lore raw
In reply to Blu
Quoted 7 lines · Ryan Johnson

Could you send me the output of route -n?

Your two network cards should not be in the same network, if they are, it is not a rotuer. The whole purpose of a router is a gateway for clients on a network to get to another network that they (clients) do not know how to reach.

Ryan

Anyway thanks Ryan, I just wanted to confirm from you, whether we can have two NIC's in a m/c connected to a same network. Output of route -n is :-

Destination Gateway Genmask Flags Metric
Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U
0 0 0 eth1
192.168.1.0 0.0.0.0 255.255.255.0 U 0
0 0 eth1
127.0.0.0 0.0.0.0 255.0.0.0 U
0 0 0 lo
0.0.0.0 192.168.1.2 0.0.0.0 UG
0 0 0 eth0

what I was expecting was:-

Destination Gateway Genmask Flags Metric
Ref Use Iface
192.168.1.0 0.0.0.0 255.255.255.0 U
0 0 0 eth0
192.168.1.0 0.0.0.0 255.255.255.0 U 0
0 0 eth1
127.0.0.0 0.0.0.0 255.0.0.0 U
0 0 0 lo
0.0.0.0 192.168.1.2 0.0.0.0 UG
0 0 0 eth0

Regards
-Raghu

Quoted 65 lines
Quoted 61 lines
Quoted 8 lines · Ryan Johnson

I am going to assume you want the most basic router, just two interfaces.

1.) Make sure both network cards have been detected. ifconfig eth0
ifconfig eth1

Can I have both the network cards in the same n/w...? Becoz If I try to use both NIC's with the same n/w, running <$ route -n> we can see either eth1 or eth0 repeated twice. Pls let me know where is the problem..?

Regards
-Raghu

Quoted 25 lines

2.) Set up each interface on its own network, make sure the interface has been activated, you can use ifconfig for this. 3.) issue the command
echo 1 > /proc/sys/net/ipv4/ip_forward
to enable ip fowarding, w/o this the kernel will not send packets between interfaces
4.) set the clients behind the router to point to the internal ip of your router

Any changes made to the system will have to be initialized during the boot process.

Of course if you have ip addresses that you would like to nat/masq behind the router, you will have to use iptables.

You really should be more specific on your needs.

Good luck.

Quoted 6 lines

Good morning at all, thanks for previous help, but I have another ask. I have a few experience of Linux world's, and I need to configure a Linux PC as router, what are the steps? What do I do? Thanks.

Quoted 8 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Signature · 12 lines
****** This email is confidential and is intended for the original recipient(s)
only. If you have erroneously received this mail, please delete it immediately
and notify the sender. Unauthorized copying, disclosure or distribution of the
material in this mail is prohibited. Views expressed in this mail are those of
the individual sender and do not bind Gsec1 Limited. or its subsidiary, unless
the sender has done so expressly with due authority of Gsec1.******
 


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/