Skip to contentSkip to conversation

Two uplink provides with debian ( woody ) - problem to insert route in a table

LARTC [email protected] 3 participants 3 messages Nov 5, 2003

lore
Share & tools
lore
#0 lore raw

Hello,

I'm trying to configure iproute2 with two providers in a Load balancing configuration according "Linux Advanced Routing & Traffic Control HOWTO".

I'm working with two links:
- static ip (adsl link - 256Kbps)
- dynamic ip (512kbps).

In my HedHat 7.2 everything works well, but in my debian (woody) something wrong is going on. First I have to create two tables, one for each provider. That's ok, but when I try to add an route to one of these tables, it goes to main table.

# ip route add default via $P1 table T1
looks OK, but the route goes to table main
# ip route add default via $P2 table T2
NOK, because it goes to table main too, not to table T2.

Any clues???

Thanks in advance,
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Try this

ip route $P1 default scope global nexthop via 10.129.30.1 dev eth0 weight 1 \
nexthop via 10.129.31.1 dev eth1 weight 1

Quoted 3 lines

Hello,

I'm trying to configure iproute2 with two providers in a Load balancing

configuration according "Linux Advanced Routing & Traffic Control HOWTO".

Quoted 6 lines

I'm working with two links:
- static ip (adsl link - 256Kbps)
- dynamic ip (512kbps).

In my HedHat 7.2 everything works well, but in my debian (woody) something

wrong is going on. First I have to create two tables, one for each provider. That's ok, but when I try to add an route to one of these tables, it goes to main table.

Quoted 7 lines
# ip route add default via $P1 table T1
looks OK, but the route goes to table main
# ip route add default via $P2 table T2
NOK, because it goes to table main too, not to table T2.
Quoted 7 lines

Any clues???

Thanks in advance,
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to [email protected]

Hi,
[email protected] wrote on 2003-11-05:

Quoted 4 lines

In my HedHat 7.2 everything works well, but in my debian (woody) something wrong is going on. First I have to create two tables, one for each provider. That's ok, but when I try to add an route to one of these tables, it goes to main table.

It sounds stupid, I know, but it happened to me before:

Do you have duplicate numeric ids in /etc/iproute2/rt_tables?

ciao,

Signature · 7 lines
[*Thomas  Themel*] [...] this quickly escalated into a Holy War with Emacs 
[extended contact] users on one side and Jeep Wrangler drivers on the other. 
[info provided in] It was hard to tell but I think Emacs came out as the better
[*message header*] utility vehicle.     - Casey West
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/