htb rate > 30mbit not working
Hello,
I tried to set shaper on my local lan with HTB and rate 60mbit I used linux-2.4.22 and tried with 2.4.23rc1 - all QoS and HTB related staff compiled like modules. In both kernels the rate did not reach more than 30mbit( 3MB/sec )
When I delete shaper I can reach 9MB/sec ( about 74mbit ) if I set shaper more than 25mbit the speed did not increase :)
I tried this with kernel 2.6.test9 and everything is OK shaper works on 60mbit - so I think this is problem of the current kernel
Any ideas ? :)
Signature · 7 lines
Regards, Svetlin Simeonov _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 5 lines
I tried to set shaper on my local lan with HTB and rate 60mbit I used linux-2.4.22 and tried with 2.4.23rc1 - all QoS and HTB related staff compiled like modules. In both kernels the rate did not reach more than 30mbit( 3MB/sec )
Quoted 7 lines
When I delete shaper I can reach 9MB/sec ( about 74mbit ) if I set shaper more than 25mbit the speed did not increase :)
I tried this with kernel 2.6.test9 and everything is OK shaper works on 60mbit - so I think this is problem of the current kernel
Any ideas ? :)
Well there are two new things I can think of in 2.6 vs 2.4. One is that the HZ constant is bigger which peraps can make latencies in the kernel smaller... but I don't know if HZ has any influence on HTB performance.
Also 2.6 has NAPI, a new API for network card drivers that modifies the drivers behaviour to better reflect the usage. Its interupt driven on lighter loads, but "poll"-ing based on higher load.
Anyway you can run 2.6 its not that bad.
Signature · 5 lines
Damjan Georgievski jabberID: [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 2 lines · Damjan
Anyway you can run 2.6 its not that bad.
There was a report some time ago about HTB not shaping to the specified bandwidth in 2.6.x when traffics consists of small-sized packages. See:
http://bugzilla.kernel.org/show_bug.cgi?ide7
This supposed bug has yet to be acknowledged by some developers.
Signature · 5 lines
Jose Luis Domingo Lopez Linux Registered User #189436 Debian Linux Sid (Linux 2.6.0-test9-mm2) _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hello again,
I tested it with MTU 128 and it works fine :) ... for now I will set it with 2.6 kernel
Thanks a lot :)
on Wednesday, November 12, 2003, 12:49:01 AM, ste napisali
SS> Hello,
SS> I tried to set shaper on my local lan with HTB and rate 60mbit SS> I used linux-2.4.22 and tried with 2.4.23rc1 - all QoS and HTB related SS> staff compiled like modules. In both kernels the rate did not reach SS> more than 30mbit( 3MB/sec )
SS> When I delete shaper I can reach 9MB/sec ( about 74mbit ) SS> if I set shaper more than 25mbit the speed did not increase :)
SS> I tried this with kernel 2.6.test9 and everything is OK shaper works SS> on 60mbit - so I think this is problem of the current kernel
SS> Any ideas ? :)
Signature · 7 lines
Regards, Svetlin Simeonov _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/