How to route and queue, based on iptables marked packets, at the same time?
Hi
I want to do some routing an queuing stuff, but I am not sure if this will work.
I have 3 connections on my router:
- eth0 which points to my LAN
- eth1 which point to the Internet over a 2Mbit connection
- eth2/ppp0 which is a DSL connection and points to the Internet, too.
The reason for the two Internet connections is that the 2Mbit connection is fast but expensive, I have to pay the traffic. The DSL connection is flat fee but slow, 384 k/bit up and 64 k/bit downstream.
Both connections do masquerading with their public IPs.
What I want to do is to route some services over the DSL connection, like e-mail traffic. The default route should be the 2Mbit connection.
AFAIK I can't use ip rules to set up routing policies based on the TCP-port, so I want to mark the traffic with iptables, to set the routs. My problem is, that I currently use this to prioritise my traffic and to order them into different HTB and SFQ queues.
I found this graphic in the LARTC HOWTO:
+------------+ +---------+ +-------------+
Packet -| PREROUTING |- routing--| FORWARD |----+-| POSTROUTING |- Packets
input +------------+ decision +---------+ | +-------------+ out
| |
+-------+ +--------+
| INPUT |-Local process -| OUTPUT |
+-------+ +--------+My question is can I mark the packets once in the FORWARD and OUTPUT chain to influence the routing decision, and mark them again in the PORSTROUTING chain to influence the queuing? Where is the decision how to route?
My routing configuration:
# Routing table for the 2MBit interface
$IP route add "$EXT_2M_NET" dev "$EXT_2M_IF" src "$EXT_2M_IP" table "$EXT_2M_RT" $IP route add default via "$EXT_2M_ROUTER" table "$EXT_2M_RT"
$IP route add "$EXT_2M_NET" dev "$EXT_2M_IF" src "$EXT_2M_IP"
# Routing table for the DSL interface
$IP route add "$EXT_DSL_NET" dev "$EXT_DSL_IF" src "$EXT_DSL_IP" table "$EXT_DSL_RT" $IP route add default via "$EXT_DSL_ROUTE"R table "$EXT_DSL_RT"
$IP route add "$EXT_DSL_NET" dev "$EXT_DSL_IF" src "$EXT_DSL_IP"
# Routing rules
$IP rule add from "$EXT_2M_IP" table "$EXT_2M_RT" $IP rule add from "$EXT_DSL_IP" table "$EXT_DSL_RT"
$IP rule add fwmark 10 table "$EXT_2M_RT"
$IP rule add fwmark 20 table "$EXT_DSL_RT"
$IP route add "$INT_NET" dev "$INT_IF" table "$EXT_2M_RT" $IP route add "$EXT_DSL_NET" dev "$EXT_DSL_IF" table "$EXT_2M_RT" $IP route add 127.0.0.0/8 dev lo table "$EXT_2M_RT"
$IP route add "$INT_NET" dev "$INT_IF" table "$EXT_DSL_RT" $IP route add "$EXT_2M_NET" dev "$EXT_2M_IF" table "$EXT_DSL_RT" $IP route add 127.0.0.0/8 dev lo table "$EXT_DSL_RT"
$IP route add default via "$EXT_2M_IP"
thx,
Jan GerritsenÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿË™¨¥Šx%ŠË,SùšŠYšŸ÷lõ¯ç–m§ÿÿ™¨¥™©ÿvÏZþy™¨¥™©ÿ–+-ŠwèþV«µÁÎY3ÿ†Ûiÿÿåj»\þŠà
Witaj Jan,
W Twoim li�cie datowanym 4 grudnia 2003 (13:01:51) moΏna przeczytaζ:
Yes, you can. You can do marking in output and it will make a difference in routing. Just use the -mangle- tables.
Checked and verified. I use it.
JG> Hi
JG> I want to do some routing an queuing stuff, but I am not sure if this JG> will work.
JG> I have 3 connections on my router:
JG> - eth0 which points to my LAN
JG> - eth1 which point to the Internet over a 2Mbit connection JG> - eth2/ppp0 which is a DSL connection and points to the Internet, too.
JG> The reason for the two Internet connections is that the 2Mbit connection JG> is fast but expensive, I have to pay the traffic. The DSL connection is JG> flat fee but slow, 384 k/bit up and 64 k/bit downstream.
JG> Both connections do masquerading with their public IPs.
JG> What I want to do is to route some services over the DSL connection, like JG> e-mail traffic. The default route should be the 2Mbit connection.
JG> AFAIK I can't use ip rules to set up routing policies based on the TCP-port, JG> so I want to mark the traffic with iptables, to set the routs. JG> My problem is, that I currently use this to prioritise my traffic and to JG> order them into different HTB and SFQ queues.
JG> I found this graphic in the LARTC HOWTO:
JG> +------------+ +---------+ +-------------+ JG> Packet -| PREROUTING |- routing--| FORWARD |----+-| POSTROUTING |- Packets JG> input +------------+ decision +---------+ | +-------------+ out JG> | | JG> +-------+ +--------+ JG> | INPUT |-Local process -| OUTPUT | JG> +-------+ +--------+
JG> My question is can I mark the packets once in the FORWARD and OUTPUT chain JG> to influence the routing decision, and mark them again in the PORSTROUTING JG> chain to influence the queuing? Where is the decision how to route?
JG> My routing configuration:
JG> # Routing table for the 2MBit interface
JG> $IP route add "$EXT_2M_NET" dev "$EXT_2M_IF" src "$EXT_2M_IP" table "$EXT_2M_RT" JG> $IP route add default via "$EXT_2M_ROUTER" table "$EXT_2M_RT"
JG> $IP route add "$EXT_2M_NET" dev "$EXT_2M_IF" src "$EXT_2M_IP"
JG> # Routing table for the DSL interface
JG> $IP route add "$EXT_DSL_NET" dev "$EXT_DSL_IF" src JG> "$EXT_DSL_IP" table "$EXT_DSL_RT"
JG> $IP route add default via "$EXT_DSL_ROUTE"R table "$EXT_DSL_RT" JG> $IP route add "$EXT_DSL_NET" dev "$EXT_DSL_IF" src "$EXT_DSL_IP"
JG> # Routing rules
JG> $IP rule add from "$EXT_2M_IP" table "$EXT_2M_RT" JG> $IP rule add from "$EXT_DSL_IP" table "$EXT_DSL_RT"
JG> $IP rule add fwmark 10 table "$EXT_2M_RT"
JG> $IP rule add fwmark 20 table "$EXT_DSL_RT"
JG> $IP route add "$INT_NET" dev "$INT_IF" table "$EXT_2M_RT" JG> $IP route add "$EXT_DSL_NET" dev "$EXT_DSL_IF" table "$EXT_2M_RT" JG> $IP route add 127.0.0.0/8 dev lo table "$EXT_2M_RT"
JG> $IP route add "$INT_NET" dev "$INT_IF" table "$EXT_DSL_RT" JG> $IP route add "$EXT_2M_NET" dev "$EXT_2M_IF" table "$EXT_DSL_RT" JG> $IP route add 127.0.0.0/8 dev lo table "$EXT_DSL_RT"
JG> $IP route add default via "$EXT_2M_IP"
JG> thx,
JG> Jan
JG> Gerritsen�����������������������������������ΛΒ™¨¥�x%�Λ,Sω��Y��χlυ―η–m§��™¨¥™©�vΟZώy™¨¥™©�–+-�wθώV«µΑΞY3�†Ϋi��εj»\ώ�ΰ
Signature · 3 lines
Pozdrowienia, Robert mailto:[email protected] �����������������������������������ΛΒ™¨¥�x%�Λ,Sω��Y��χlυ―η–m§��™¨¥™©�vΟZώy™¨¥™©�–+-�wθώV«µΑΞY3�†Ϋi��εj»\ώ�ΰ
Hi,
Quoted 4 lines
Yes, you can. You can do marking in output and it will make a difference in routing. Just use the -mangle- tables.
Checked and verified. I use it.
Can I mark the packets in the POSTROUTING table again to influence the queuing?
thx,
Jan Gerritsen
ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿË™¨¥Šx%ŠË,SùšŠYšŸ÷lõ¯ç–m§ÿÿ™¨¥™©ÿvÏZşy™¨¥™©ÿ–+-ŠwèşV«µÁÎY3ÿ†Ûiÿÿåj»\şŠà