Skip to contentSkip to conversation

Simulation with Packet Lost and Packet Delays

LARTC Tony Yat-Tung Cheung 3 participants 4 messages Dec 21, 2003 – Dec 24, 2003

lore
Share & tools
lore
#0 lore raw

Hi All,

I would like to be able to simulate network congestion and delay on tcp/udp connections between two hosts. I would need to simulate packet lost and packet delay.

I think I would need to use a Linux box with two network cards to act as a pass-through ethernet bridge. Is it the case? Does this how-to guide provides good information in this area?

Thank you very much! Any advice will be much appreciated.

Best Regards,
Tony Cheung

#1 lore raw
Quoted 9 lines · Tony Yat-Tung Cheung

Hi All,

I would like to be able to simulate network congestion and delay on tcp/udp connections between two hosts. I would need to simulate packet lost and packet delay.

I think I would need to use a Linux box with two network cards to act as a pass-through ethernet bridge. Is it the case? Does this how-to guide provides good information in this area?

http://snad.ncsl.nist.gov/itg/nistnet/

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw

Re: [LARTC] Simulation with Packet Lost and Packet Delays (How to

In reply to Tony Yat-Tung Cheung
Quoted 16 lines

From: Stef Coene <[email protected]>
To: [email protected],
Tony Yat-Tung Cheung <[email protected]>, [email protected]
Subject: Re: [LARTC] Simulation with Packet Lost and Packet Delays
Date: Mon, 22 Dec 2003 17:03:27 +0100

Quoted 6 lines · Tony Yat-Tung Cheung

Hi All,

I would like to be able to simulate network congestion and delay on tcp/udp connections between two hosts. I would need to simulate packet lost and packet delay.

Quoted 10 lines
Quoted 5 lines

I think I would need to use a Linux box with two network cards to act as a pass-through ethernet bridge. Is it the case? Does this how-to guide provides good information in this area?

http://snad.ncsl.nist.gov/itg/nistnet/

Stef

Hi Stef and others,

Thanks. The NISTNET looks like a very decent package. I have tried it briefly on a Red Hat 7.2 and it seems to work fine.

I have another basic question and I would if anyone could help me out.

Basically, I am trying a setup a Linux router between two local subnets, 192.168.0.1/24 and 192.168.1.1/24. My Linux box has two ethernet cards, eth0 has IP address 192.168.0.1 (subnet mask 255.255.255.0) and eth1 has IP address 192.168.1.1 (subnet mask: 255.255.255.0). Now I wish my Linux box to be able to route traffic between eth0 and eth1.

I have modified '/etc/sysctl.conf' to,

# Controls IP packet forwarding
net.ipv4.ip_forward = 1

However, it doesn't seem to work right now. Is there anything else I need to do? I wish to set it up quickly and would appreciate any advice!

Thank you.

Best Regards,
Tony Cheung

#3 lore raw

Re: [LARTC] Simulation with Packet Lost and Packet Delays (How toset

In reply to Tony Yat-Tung Cheung

Did you try a traceroute from subnet so you can see where fails because if you a linux box with two nics,
eth0: 192.168.0.1/24 and eth1: 192.168.1.1/24, behind the linux computer A: 192.168.0.2/24 gw 192.168.0.1, computer B: 192.168.1.2/24 gw 192.168.1.1, you must be able to ping from a to b or vice-versa unless if you set a rule to not do it. Check it out and return.

[]´s
Anderson

Quoted 4 lines
Quoted 4 lines

From: Stef Coene <[email protected]>
To: [email protected],
Tony Yat-

Tung Cheung <[email protected]>, [email protected]. nl

Quoted 1 line
Quoted 1 line

Subject: Re: [LARTC] Simulation with Packet Lost and P

acket Delays

Quoted 3 lines
Quoted 3 lines

Date: Mon, 22 Dec 2003 17:03:27 +0100

On Sunday 21 December 2003 16:31, Tony Yat-

Quoted 5 lines · Tung Cheung
Quoted 5 lines
Quoted 5 lines

Hi All,

I would like to be able to simulate network congestio

n and delay on

Quoted 1 line
Quoted 1 line
Quoted 1 line

tcp/udp connections between two hosts. I would need t

o simulate packet

Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

lost and packet delay.

I think I would need to use a Linux box with two netw

ork cards to act as

Quoted 1 line
Quoted 1 line
Quoted 1 line

a pass-

through ethernet bridge. Is it the case? Does this how- to guide

Quoted 11 lines
Quoted 8 lines
Quoted 3 lines

provides good information in this area?

http://snad.ncsl.nist.gov/itg/nistnet/

Stef

Hi Stef and others,

Thanks. The NISTNET looks like a very decent package. I

have tried it

Quoted 3 lines

briefly on a Red Hat 7.2 and it seems to work fine.

I have another basic question and I would if anyone cou

ld help me out.

Quoted 2 lines

Basically, I am trying a setup a Linux router between t

wo local subnets,

Quoted 1 line

192.168.0.1/24 and 192.168.1.1/24. My Linux box has two

ethernet cards,

Quoted 1 line

eth0 has IP address 192.168.0.1 (subnet mask 255.255.25

5.0) and eth1 has

Quoted 1 line

IP address 192.168.1.1 (subnet mask: 255.255.255.0). No

w I wish my Linux

Quoted 8 lines

box to be able to route traffic between eth0 and eth1.

I have modified '/etc/sysctl.conf' to,

# Controls IP packet forwarding
net.ipv4.ip_forward = 1

However, it doesn't seem to work right now. Is there an

ything else I

Quoted 1 line

need to do? I wish to set it up quickly and would appre

ciate any advice!

Quoted 10 lines

Thank you.

Best Regards,
Tony Cheung

__________________________________________________________________________
Acabe com aquelas janelinhas que pulam na sua tela. AntiPop-up UOL - É grátis!
http://antipopup.uol.com.br/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/