Skip to contentSkip to conversation

IP Aliasing with "IP"?

LARTC billy [email protected] 3 participants 5 messages Jan 30, 2001

lore
Share & tools
lore

billy [email protected]

author
#0 lore raw

<PRE>Can I do something like this?

old way:

ifconfig eth1 192.168.101.1 netmask 255.255.255.0 up route add -net 192.168.101.0 netmask 255.255.255.0 eth1 ifconfig eth1:0 192.168.101.1 netmask 255.255.255.0 up route add -net 192.168.101.0 netmask 255.255.255.0 eth1:0

thanks

</PRE>

#1 lore raw

<PRE>On Tue, Jan 30, 2001 at 05:50:01PM -0300, billy wrote:
&gt;<i>
</I>&gt;<i> Can I do something like this?
</I>&gt;<i>
</I>&gt;<i> old way:
</I>&gt;<i>
</I>&gt;<i> ifconfig eth1 192.168.101.1 netmask 255.255.255.0 up </I>&gt;<i> route add -net 192.168.101.0 netmask 255.255.255.0 eth1 </I>&gt;<i> ifconfig eth1:0 192.168.101.1 netmask 255.255.255.0 up </I>&gt;<i> route add -net 192.168.101.0 netmask 255.255.255.0 eth1:0 </I>
ip addr add dev eth0 192.168.101.1 etc etc should work

Signature · 6 lines
PowerDNS                     Versatile DNS Services  
Trilab                       The Technology People   
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet


</PRE>
author
#2 lore raw
In reply to billy [email protected]

<PRE>On Tuesday 30 January 2001 17:51, you wrote:
&gt;<i> On Tue, Jan 30, 2001 at 05:50:01PM -0300, billy wrote:
</I>&gt;<i> &gt; Can I do something like this?
</I>&gt;<i> &gt;
</I>&gt;<i> &gt; old way:
</I>&gt;<i> &gt;
</I>&gt;<i> &gt; ifconfig eth1 192.168.101.1 netmask 255.255.255.0 up </I>&gt;<i> &gt; route add -net 192.168.101.0 netmask 255.255.255.0 eth1 </I>&gt;<i> &gt; ifconfig eth1:0 192.168.101.1 netmask 255.255.255.0 up </I>&gt;<i> &gt; route add -net 192.168.101.0 netmask 255.255.255.0 eth1:0 </I>&gt;<i>
</I>&gt;<i> ip addr add dev eth0 192.168.101.1 etc etc should work </I>

OK, but what about eth0:0, the alias ? if I do something like:

# ip addr add dev eth0:0 192.168.101.1 etc etc

I get an error:

cannot find device &quot;eth0:0&quot;

but I can create eth0:0 with ifconfig, but &quot;ip link show&quot; does not show me the interfaces, but with &quot;ip route show&quot; I see all of the eth0:x as only eth0.

# ip route show
200.51.164.128/29 dev eth0  proto kernel  scope link  src 200.51.164.131
192.168.101.0/24 dev eth0  proto kernel  scope link  src 192.168.101.1
192.168.102.0/24 dev eth0  proto kernel  scope link  src 192.168.102.1
127.0.0.0/8 dev lo  scope link
default via 200.51.164.134 dev eth0                                           
#

is this ok? I haev to create the &quot;virtual&quot; interfaces with ifconfig or do I have a way with ip?

thanks billy

</PRE>

#3 lore raw
In reply to billy [email protected]

<PRE>On Tue, Jan 30, 2001 at 06:08:00PM -0300, billy wrote:

&gt;<i> OK, but what about eth0:0, the alias ? if I do something like:
</I>
Those 0:0 names are just imagined by ifconfig :-) iproute2 reflects reality.

&gt;<i> is this ok? I haev to create the &quot;virtual&quot; interfaces with ifconfig or do I </I>&gt;<i> have a way with ip?
</I>
ip adds IP addresses to your physical interface - which is better than inventing 'new' interfaces.

Regards,

bert hubert

Signature · 6 lines
PowerDNS                     Versatile DNS Services  
Trilab                       The Technology People   
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet


</PRE>
#4 lore raw
In reply to billy [email protected]

<PRE>On/Dnia Tue, Jan 30, 2001 at 06:08:00PM -0300, billy wrote/napisa³(a) &gt;<i> &gt; ip addr add dev eth0 192.168.101.1 etc etc should work
</I>&gt;<i> OK, but what about eth0:0, the alias ? if I do something like:
</I>&gt;<i> # ip addr add dev eth0:0 192.168.101.1 etc etc
</I>&gt;<i> I get an error:
</I>&gt;<i> cannot find device &quot;eth0:0&quot;
</I>[<A HREF="mailto:root@arm">root@arm</A> misiek]# ip addr add 1.1.1.1 dev eth0 label eth0:qpa [<A HREF="mailto:root@arm">root@arm</A> misiek]# ifconfig | grep qpa
eth0:qpa Link encap:Ethernet HWaddr 00:E0:7D:8A:4C:79

&gt;<i> but I can create eth0:0 with ifconfig, but &quot;ip link show&quot; does not show me </I>&gt;<i> the interfaces, but with &quot;ip route show&quot; I see all of the eth0:x as only eth0. </I>&gt;<i>
</I>&gt;<i> is this ok? I haev to create the &quot;virtual&quot; interfaces with ifconfig or do I </I>&gt;<i> have a way with ip?
</I>It's ok. Routing is to real device, not to so called ,,aliases''.

Signature · 5 lines
Arkadiusz Mi¶kiewicz, AM2-6BONE    [ PLD GNU/Linux IPv6 ]
<A HREF="http://www.t17.ds.pwr.wroc.pl/~misiek/ipv6/">http://www.t17.ds.pwr.wroc.pl/~misiek/ipv6/</A>   [ enabled ]


</PRE>