Skip to contentSkip to conversation

pointopoint flag

LARTC mike stjohn 4 participants 8 messages Mar 22, 2001 – Mar 25, 2001

lore
Share & tools
lore
#1 lore raw

the pointtopoint flag is something typical for the medium used. E.g. ethernet is by nature a broadcast medium and thus not pointtopoint. PPP, as its name says,is a point to point protocol. So this is (or should be) not configurable, unless you are trying some weird setups.

Guy

Quoted 6 lines · mike stjohn

how do you set the pointopoint flag using ip command?

is it an automatic setting when ip is configuring a ppp link | or am I missing something in the ip-cref.

Quoted 8 lines

thanks

msj

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#2 lore raw
In reply to mike stjohn
Quoted 4 lines · Guy Van Den Bergh

the pointtopoint flag is something typical for the medium used. E.g. ethernet is by nature a broadcast medium and thus not pointtopoint. PPP, as its name says,is a point to point protocol. So this is (or should be) not configurable, unless you are trying some weird setups.

You CAN use Ethernet in a point-to-point configuration, by the way. Saves some IP adresses.

Regards,

bert

Signature · 7 lines
http://www.PowerDNS.com      Versatile DNS Services  
Trilab                       The Technology People   
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
#3 lore raw
In reply to mike stjohn
Quoted 4 lines · bert hubert

You CAN use Ethernet in a point-to-point configuration, by the way. Saves some IP adresses.

How do you that? PPPoE (PPP over Ethernet)? This is more like ppp emulation over ethernet. And thus this introduces protocol overhead.

What do you mean by this? I'm puzzled.

Guy

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#4 lore raw
In reply to mike stjohn
Quoted 12 lines · bert hubert
Quoted 7 lines · Guy Van Den Bergh
Quoted 2 lines

You CAN use Ethernet in a point-to-point configuration, by the way. Saves some IP adresses.

How do you that? PPPoE (PPP over Ethernet)? This is more like ppp emulation over ethernet. And thus this introduces protocol overhead.

What do you mean by this? I'm puzzled.

Quoted 6 lines

It's still ethernet. But instead of assigning a /30 with 4 IP addresses, you just route to your device. Not rocket science, just saves IP addresses.

Regards,

bert hubert

But you require the next hop to do proxy arp if you would like this to work!
And certainly this is not a point-to-point configuration of ethernet. If you route to your device instead of your nexthop the kernel is going to send an arp request for de destination address, and if the destination is not on the lan, some router on the lan has to do proxy arp on behalf of the destination. Otherwise your packets will be dropped. The kernel still thinks the lan is a broadcast medium.

I believe this is a lot more complicated than "just routing to your device"!

Even if you have a crossconnect cable between two hosts or routers, the medium inbetween is still broadcast and not point-to-point.

I know this discussion is going way too far into semantics, but as far as I know there is no such thing as point-to-point mode of ethernet.

Guy

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#5 lore raw
In reply to mike stjohn
Quoted 7 lines · Guy Van Den Bergh
Quoted 2 lines

You CAN use Ethernet in a point-to-point configuration, by the way. Saves some IP adresses.

How do you that? PPPoE (PPP over Ethernet)? This is more like ppp emulation over ethernet. And thus this introduces protocol overhead.

What do you mean by this? I'm puzzled.

It's still ethernet. But instead of assigning a /30 with 4 IP addresses, you just route to your device. Not rocket science, just saves IP addresses.

Regards,

bert hubert

Signature · 7 lines
http://www.PowerDNS.com      Versatile DNS Services  
Trilab                       The Technology People   
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
#6 lore raw
In reply to mike stjohn
Quoted 6 lines · Guy Van Den Bergh

But you require the next hop to do proxy arp if you would like this to work!
And certainly this is not a point-to-point configuration of ethernet. If you route to your device instead of your nexthop the kernel is going to send an arp request for de destination address, and if the destination is not on the lan, some router on the lan has to do proxy arp on behalf of the destination. Otherwise your packets will be dropped. The kernel still thinks the lan is a broadcast medium.

Quoted 6 lines

I believe this is a lot more complicated than "just routing to your device"!

Even if you have a crossconnect cable between two hosts or routers, the medium inbetween is still broadcast and not point-to-point.

I know this discussion is going way too far into semantics, but as far as I know there is no such thing as point-to-point mode of ethernet.

You can disable arp and set static arp entries. Do that, plus a crossover cable and full-duplex, and I'd have a very hard time calling your ethernet anything but point-to-point. :)

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#7 lore raw
In reply to mike stjohn
Quoted 6 lines · Gregory Maxwell
Quoted 4 lines · Guy Van Den Bergh

Even if you have a crossconnect cable between two hosts or routers, the medium inbetween is still broadcast and not point-to-point.

Quoted 6 lines
Quoted 1 line

I know this discussion is going way too far into semantics, but as far as I know there is no such thing as point-to-point mode of ethernet.

You can disable arp and set static arp entries. Do that, plus a crossover cable and full-duplex, and I'd have a very hard time calling your ethernet anything but point-to-point. :)

The point was that it is a lot more complex than simply adding a route to the device instead of to the nexthop.
Let's remember that ethernet is by nature a broadcast medium and if you want it to behave like a point-to-point link you will have to be careful. Adding static arp entries has some drawbacks which you do not have on real point-to-point links.
In the end you are still trying to let a broadcast medium behave like a point-to-point link. Nothing more and nothing less.

Guy

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/