Skip to contentSkip to conversation

urgent help needed in iproute2+tc

LARTC Ravikanth Samprathi 2 participants 3 messages Apr 10, 2001 – Apr 19, 2001

lore
Share & tools
lore
#0 lore raw

Hi all,
I am running linux-2.4.0 with
3 interfaces - eth0, eth1, and eth2.

eth0 is the outgoing WAN interface. eth1 and eth2 are the internal LAN interfaces. eth1 and eth2 belong to a bridge group br0. eth1 is connected to a voice-over-ip phone. eth2 is connected to a pc.

so, the setup is

                       ------------------------------
	            |                             |
voip-phone --->| eth1  --->               |
	            |	  br0   eth0 -|---WAN
lan-pc ---------->| eth2 ---->               |
                       ------------------------------

voip-phone can talk with lan-pc through-the-bridge-group.
voip phone can also talk with any other phone in the outside-world-through-the-WAN.

I need to setup QoS so that all packets from voip-phone (that is destined to either eth1, eth2 or to eth0) are provided with high-priority-low-delay service. voip-phone can be on any lan-interface (eth1 or eth2). The only thing that can be surely said about the voip-phone is that it will have only a particular set of ip addresses ranging from 171.72.233.100 to 171.72.233.200.

To implement this, i downloaded the iproute2+tc tool version iproute2-2.2.4-now-ss991023.tar.gz and went through the README files.

Can somebody please help me in writing the commands? That will
be of great help.

Thanking you in advance,
ravi

--------------------------------------------------->
Ravi Samprathi work:(408)853-8038
Cisco Systems res :(408)988-2268
Empowering the Internet Generation <---------------------------------------------------

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#1 lore raw

Hi Ravi,

First you must know what port is used on voip.
To check the correct port of voip, you can use Etherreal, tcpdump or Sniffer.
I guess it is the same as H.323 on MS NetMeeting used with UDP port 1720. Port 1720 = 0x06B8.

In here we use priority and simple FIFO queuing. Both queuing are used in ordinary Cisco Routers.
Below is the commands:

------------------------------
###### To control eth0 ######
#Create Priority queuing (minimum 3 bands)
tc qdisc add dev eth0 root handle 1: prio bands 3 priomap 0 1 2

#Create FIFO queuing and attach to priority queuing tc qdisc add dev eth0 parent 1:1 handle 2: pfifo limit 1024 tc qdisc add dev eth0 parent 1:2 handle 3: pfifo limit 1024 tc qdisc add dev eth0 parent 1:3 handle 4: pfifo limit 1024

#Installing a u32 classifier for the traffic
#In Cisco router 'tc filter' command has same function as access-list tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 divisor 1

# Filter UDP traffic which has destination port 1720 (0x06B8) and direct
# this traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth0 parent 1:0 prio 1 u32 match udp src 0x06B8 0xffff \
flowid 1:1
# Filter UDP traffic which has source port 1720 (0x06B8) and direct this
# traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth0 parent 1:0 prio 1 u32 match udp dst 0x06B8 0xffff \
flowid 1:1

###### To control eth1 ######
#Create Priority queuing (minimum 3 bands)
tc qdisc add dev eth1 root handle 1: prio bands 3 priomap 0 1 2

#Create FIFO queuing and attach to priority queuing tc qdisc add dev eth1 parent 1:1 handle 2: pfifo limit 1024 tc qdisc add dev eth1 parent 1:2 handle 3: pfifo limit 1024 tc qdisc add dev eth1 parent 1:3 handle 4: pfifo limit 1024

#Installing a u32 classifier for the traffic
#In Cisco router 'tc filter' command has same function as access-list tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 divisor 1

# Filter UDP traffic which has destination port 1720 (0x06B8) and direct
# this traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth1 parent 1:0 prio 1 u32 match udp src 0x06B8 0xffff \
flowid 1:1
# Filter UDP traffic which has source port 1720 (0x06B8) and direct this
# traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth1 parent 1:0 prio 1 u32 match udp dst 0x06B8 0xffff \
flowid 1:1

###### To control eth2 ######
#Create Priority queuing (minimum 3 bands)
tc qdisc add dev eth2 root handle 1: prio bands 3 priomap 0 1 2

#Create FIFO queuing and attach to priority queuing tc qdisc add dev eth2 parent 1:1 handle 2: pfifo limit 1024 tc qdisc add dev eth2 parent 1:2 handle 3: pfifo limit 1024 tc qdisc add dev eth2 parent 1:3 handle 4: pfifo limit 1024

#Installing a u32 classifier for the traffic
#In Cisco router 'tc filter' command has same function as access-list tc filter add dev eth2 parent 1:0 protocol ip prio 1 u32 divisor 1

# Filter UDP traffic which has destination port 1720 (0x06B8) and direct
# this traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth2 parent 1:0 prio 1 u32 match udp src 0x06B8 0xffff \
flowid 1:1
# Filter UDP traffic which has source port 1720 (0x06B8) and direct this
# traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth2 parent 1:0 prio 1 u32 match udp dst 0x06B8 0xffff \
flowid 1:1
------------------------------

I haven't tried it before. Let me know it can work or not.

Regards,

Quoted 9 lines

Date: Tue, 10 Apr 2001 16:23:43 -0700
To: [email protected]
From: Ravikanth Samprathi <[email protected]>
Subject: [LARTC] urgent help needed in iproute2+tc

Hi all,
I am running linux-2.4.0 with
3 interfaces - eth0, eth1, and eth2.

Quoted 7 lines

eth0 is the outgoing WAN interface. eth1 and eth2 are the internal LAN interfaces. eth1 and eth2 belong to a bridge group br0. eth1 is connected to a voice-over-ip phone. eth2 is connected to a pc.

so, the setup is

                        ------------------------------
                        |                            |
         voip-phone --->| eth1  --->                 |
                        |   br0                eth0 -|---WAN
      lan-pc ---------->| eth2 ---->                 |
                        ------------------------------
Quoted 29 lines

voip-phone can talk with lan-pc through-the-bridge-group.
voip phone can also talk with any other phone in the outside-world-through-the-WAN.

I need to setup QoS so that all packets from voip-phone (that is destined to either eth1, eth2 or to eth0) are provided with high-priority-low-delay service. voip-phone can be on any lan-interface (eth1 or eth2). The only thing that can be surely said about the voip-phone is that it will have only a particular set of ip addresses ranging from 171.72.233.100 to 171.72.233.200.

To implement this, i downloaded the iproute2+tc tool version iproute2-2.2.4-now-ss991023.tar.gz
and went through the README files.

Can somebody please help me in
writing the commands? That will
be of great help.

Thanking you in advance,
ravi

Quoted 9 lines

--------------------------------------------------->
Ravi Samprathi work:(408)853-8038
Cisco Systems res :(408)988-2268
Empowering the Internet Generation <---------------------------------------------------

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#2 lore raw
In reply to Ravikanth Samprathi

Hi,
One more requirement is the following:-
All the packets from the voip source (with a particular ip address, with a particular source, arriving on a particular interface) must have the TOS byte changed to the
value 0x06,
can u let me know how to do this please?
Thenx in Advance.
ravi

Quoted 151 lines · Junus Junarto D

Hi Ravi,

First you must know what port is used on voip.
To check the correct port of voip, you can use Etherreal, tcpdump or Sniffer.
I guess it is the same as H.323 on MS NetMeeting used with UDP port 1720. Port 1720 = 0x06B8.

In here we use priority and simple FIFO queuing. Both queuing are used in ordinary Cisco Routers.
Below is the commands:

------------------------------
###### To control eth0 ######
#Create Priority queuing (minimum 3 bands)
tc qdisc add dev eth0 root handle 1: prio bands 3 priomap 0 1 2

#Create FIFO queuing and attach to priority queuing tc qdisc add dev eth0 parent 1:1 handle 2: pfifo limit 1024 tc qdisc add dev eth0 parent 1:2 handle 3: pfifo limit 1024 tc qdisc add dev eth0 parent 1:3 handle 4: pfifo limit 1024

#Installing a u32 classifier for the traffic
#In Cisco router 'tc filter' command has same function as access-list tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 divisor 1

# Filter UDP traffic which has destination port 1720 (0x06B8) and direct
# this traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth0 parent 1:0 prio 1 u32 match udp src 0x06B8 0xffff \
flowid 1:1
# Filter UDP traffic which has source port 1720 (0x06B8) and direct this
# traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth0 parent 1:0 prio 1 u32 match udp dst 0x06B8 0xffff \
flowid 1:1

###### To control eth1 ######
#Create Priority queuing (minimum 3 bands)
tc qdisc add dev eth1 root handle 1: prio bands 3 priomap 0 1 2

#Create FIFO queuing and attach to priority queuing tc qdisc add dev eth1 parent 1:1 handle 2: pfifo limit 1024 tc qdisc add dev eth1 parent 1:2 handle 3: pfifo limit 1024 tc qdisc add dev eth1 parent 1:3 handle 4: pfifo limit 1024

#Installing a u32 classifier for the traffic
#In Cisco router 'tc filter' command has same function as access-list tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 divisor 1

# Filter UDP traffic which has destination port 1720 (0x06B8) and direct
# this traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth1 parent 1:0 prio 1 u32 match udp src 0x06B8 0xffff \
flowid 1:1
# Filter UDP traffic which has source port 1720 (0x06B8) and direct this
# traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth1 parent 1:0 prio 1 u32 match udp dst 0x06B8 0xffff \
flowid 1:1

###### To control eth2 ######
#Create Priority queuing (minimum 3 bands)
tc qdisc add dev eth2 root handle 1: prio bands 3 priomap 0 1 2

#Create FIFO queuing and attach to priority queuing tc qdisc add dev eth2 parent 1:1 handle 2: pfifo limit 1024 tc qdisc add dev eth2 parent 1:2 handle 3: pfifo limit 1024 tc qdisc add dev eth2 parent 1:3 handle 4: pfifo limit 1024

#Installing a u32 classifier for the traffic
#In Cisco router 'tc filter' command has same function as access-list tc filter add dev eth2 parent 1:0 protocol ip prio 1 u32 divisor 1

# Filter UDP traffic which has destination port 1720 (0x06B8) and direct
# this traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth2 parent 1:0 prio 1 u32 match udp src 0x06B8 0xffff \
flowid 1:1
# Filter UDP traffic which has source port 1720 (0x06B8) and direct this
# traffic to class 1:1 (FIFO priority 1)
tc filter add dev eth2 parent 1:0 prio 1 u32 match udp dst 0x06B8 0xffff \
flowid 1:1
------------------------------

I haven't tried it before. Let me know it can work or not.

Regards,

Quoted 9 lines

Date: Tue, 10 Apr 2001 16:23:43 -0700
To: [email protected]
From: Ravikanth Samprathi <[email protected]>
Subject: [LARTC] urgent help needed in iproute2+tc

Hi all,
I am running linux-2.4.0 with
3 interfaces - eth0, eth1, and eth2.

Quoted 7 lines

eth0 is the outgoing WAN interface. eth1 and eth2 are the internal LAN interfaces. eth1 and eth2 belong to a bridge group br0. eth1 is connected to a voice-over-ip phone. eth2 is connected to a pc.

so, the setup is

                        ------------------------------
                        |                            |
         voip-phone --->| eth1  --->                 |
                        |   br0                eth0 -|---WAN
      lan-pc ---------->| eth2 ---->                 |
                        ------------------------------
Quoted 29 lines

voip-phone can talk with lan-pc through-the-bridge-group.
voip phone can also talk with any other phone in the outside-world-through-the-WAN.

I need to setup QoS so that all packets from voip-phone (that is destined to either eth1, eth2 or to eth0) are provided with high-priority-low-delay service. voip-phone can be on any lan-interface (eth1 or eth2). The only thing that can be surely said about the voip-phone is that it will have only a particular set of ip addresses ranging from 171.72.233.100 to 171.72.233.200.

To implement this, i downloaded the iproute2+tc tool version iproute2-2.2.4-now-ss991023.tar.gz
and went through the README files.

Can somebody please help me in
writing the commands? That will
be of great help.

Thanking you in advance,
ravi

Quoted 9 lines

--------------------------------------------------->
Ravi Samprathi work:(408)853-8038
Cisco Systems res :(408)988-2268
Empowering the Internet Generation <---------------------------------------------------

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://ds9a.nl/2.4Routing/

--------------------------------------------------->
Ravi Samprathi work:(408)853-8038
Cisco Systems res :(408)988-2268
Empowering the Internet Generation <---------------------------------------------------

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/