Skip to contentSkip to conversation

why the bandwidth is not follow my config??????

LARTC Juergen 3 participants 4 messages May 4, 2001 – May 7, 2001

lore
Share & tools
lore

Juergen

author
#0 lore raw

I try to use iproute to control my bandwidth less than 3MB, but something happen. list below is my config

--------------------------------------------------------------------------------

tc qdisc add dev eth1 root handle 20: cbq bandwidth 10Mbit avpkt 1000

tc class add dev eth1 parent 20:0 classid 20:1 cbq bandwidth 10Mbit rate \
1Mbit allot 1514 weight 100Kbit prio 8 maxburst 20 avpkt 1000 bounded

tc class add dev eth1 parent 20:1 classid 20:2 cbq bandwidth 10Mbit rate \
3Mbit allot 1514 weight 200Kbit prio 5 maxburst 20 avpkt 1000 bounded

tc filter add dev eth1 parent 20:0 protocol ip prio 100 u32 match ip src \
192.168.0.1 flowid 20:1

tc filter add dev eth1 parent 20:0 protocol ip prio 25 u32 match ip src \
192.168.0.2 flowid 20:2

--------------------------------------------------------------------------------

I use download file to test this function. But the really situation about the bandwidth is ... 1MB(20:1) is 1.5Mbit
3MB(20:2)is 4.6Mbit
Have anyone met this kind of problem before????? And how to solve this problem?????

#1 lore raw

I just did the tests and these are my results : (I use ttcp to test) for class 20:1 = 71.90 KB/sec (575.2Kbit/sec)
for class 20:2 = 134.05 KB/sec (1072.4Kbit/s)

The numbers are not correct, but I think it's just CBQ that's not very accurate when you use the bounded paramter. I got the same results when I use everywhere prio8 and put class 20:2 on qdisc 20:0. So it's a CBQ accuracy problem.

Signature · 3 lines
Staf

More QOS info : http://users.belgacom.net/staf/
Quoted 20 lines

Juergen wrote:

I try to use iproute to control my bandwidth less than 3MB, but something happen.
list below is my config
----------------------------------------------------------------------
tc qdisc add dev eth1 root handle 20: cbq bandwidth 10Mbit avpkt 1000

tc class add dev eth1 parent 20:0 classid 20:1 cbq bandwidth 10Mbit rate \
1Mbit allot 1514 weight 100Kbit prio 8 maxburst 20 avpkt 1000 bounded

tc class add dev eth1 parent 20:1 classid 20:2 cbq bandwidth 10Mbit rate \
3Mbit allot 1514 weight 200Kbit prio 5 maxburst 20 avpkt 1000 bounded

tc filter add dev eth1 parent 20:0 protocol ip prio 100 u32 match ip src \
192.168.0.1 flowid 20:1

Quoted 10 lines

tc filter add dev eth1 parent 20:0 protocol ip prio 25 u32 match ip src \
192.168.0.2 flowid 20:2
----------------------------------------------------------------------
I use download file to test this function.
But the really situation about the bandwidth is ... 1MB(20:1) is 1.5Mbit
3MB(20:2)is 4.6Mbit
Have anyone met this kind of problem before?????
And how to solve this problem?????

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#2 lore raw
In reply to Juergen

Do you think this "anomaly" might be a consequence not choosing the average size correctly? Have you done some tests with a higher avgpkt value?

I suppose CBQ does packet per packet handling, assuming the average packet size is what you specified on the command line. But what if the real average packet size is bigger?

Guy

Quoted 8 lines · Stef Coene

I just did the tests and these are my results : (I use ttcp to test) for class 20:1 = 71.90 KB/sec (575.2Kbit/sec)
for class 20:2 = 134.05 KB/sec (1072.4Kbit/s)

The numbers are not correct, but I think it's just CBQ that's not very accurate when you use the bounded paramter. I got the same results when I use everywhere prio8 and put class 20:2 on qdisc 20:0. So it's a CBQ accuracy problem.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#3 lore raw
In reply to Juergen
Quoted 4 lines · Guy Van Den Bergh

Do you think this "anomaly" might be a consequence not choosing the average size correctly? Have you done some tests with a higher avgpkt value?

Could be. The problem is there is allmost no documentation on how to choose these numbers and what they change.

That's why I'm doing a lot of tests. It's possible that some of the strange results I got could be explained by a bad choice of parameters, but I have no other choice than doing another bunge of tests and to change the average size. That's how I finally figured out what you can do with the weight parameter and how you have to choose the different rates for the classes. Now I'm trying to figure out how youc an use the isolated keyword. The results will be published on my website.

Signature · 7 lines
Staf

More QOS info : http://users.belgacom.net/staf/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/