Marking returned MASQ'ed packets (ingress, TC, etc.)
Hi Folks,
I'm using a 2.4.x kernel and TC from the iproute2 package so that I can limit traffic through my gateway. I'm using this to mark packets when they leave the LAN:
/sbin/ipchains -A forward -j MASQ -i eth0 -s 192.168.1.0/24 -d 0.0.0.0/0 -m 1
When the packets return, I need to have them marked again so that the ingress filter will limit the bandwidth in the opposite direction.
The only way I have found to do this, is to mark EVERY packet like this:
/sbin/ipchains -A input -i eth0 -s 0.0.0.0/0 -d 12.10.109.52/32 -m 1
This works, but what I would really like to do, is mark the 192.168.1.0/24 packets instead (after they have been "un-masq'ed", so that I can limit bandwidth on each interface in the gateway box.
Is this possible?
Thanks,
Barton
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 3 lines
Please describe your network topology.
Sure, it's a basic masq setup with 1 external (WAN) and 2 internal (LAN) interfaces
|------------------------------------------|
| <-> eth1/192.168.241.1 | <->
192.168.241.0 LAN
Internet <-> | eth0/12.10.109.52
|
| <-> eth2/192.168.242.1 | <->192.168.242.0 LAN
|------------------------------------------|
Gateway Computer w/ 2 NICs
I want to limit the upstream (to the internet) of both eth1 and eth2 to 128kbps.
I want to limit the downstream (from the internet) of eth1 to 128kbps and 256kbps on eth2.
I can limit the upstream of both interfaces with this:
tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10Mbit avpkt 1000
cell 8
tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit
rate \
10Mbit weight 1Mbit prio 8 allot 1514 cell 8 maxburst 100 avpkt
1000
tc class add dev eth0 parent 1:1 classid 1:10 cbq bandwidth 10Mbit
rate \
128Kbit weight 12Kbit prio 5 allot 1514 cell 8 maxburst 20 avpkt
1000 bounded
tc qdisc add dev eth0 parent 1:10 tbf rate 128Kbit buffer 10Kb/8
limit 15Kb mtu 1500
tc filter add dev eth0 parent 1:0 protocol ip prio 100 handle 1 fw
classid 1:10
I can limit the downstream with this:
tc qdisc add dev eth0 handle ffff:0 ingress
tc filter add dev eth0 parent ffff:0 protocol ip prio 5 handle 1 fw \
police rate 128kbit burst 128kbit mtu 1500 drop
What I think I need is a separate filter for eth1 and eth2 that looks for different marks (handles?) Therefore, I need to mark packets coming through eth0 to eth1 with a 0x1 and from eth0 to eth2 with a 0x2 and filter accordingly (I think).
Quoted 22 lines
Quoted 22 lines
Hi Folks,
I'm using a 2.4.x kernel and TC from the iproute2 package so that I can limit traffic through my gateway. I'm using this to mark packets when they leave the LAN:
/sbin/ipchains-A forward -j MASQ -i eth0 -s 192.168.1.0/24 -d 0.0.0.0/0 -m 1When the packets return, I need to have them marked again so that the ingress filter will limit the bandwidth in the opposite direction.
The only way I have found to do this, is to mark EVERY packet like this:
/sbin/ipchains-A input -i eth0 -s 0.0.0.0/0 -d 12.10.109.52/32 -m 1This works, but what I would really like to do, is mark the 192.168.1.0/24 packets instead (after they have been "un-masq'ed", so that I can limit bandwidth on each interface in the gateway box.
Is this possible?
Quoted 9 lines
Quoted 7 lines
Thanks,
Barton
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:Quoted 1 line
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
On Tue, 12 Jun 2001, Barton Hodges wrote:
(Your ASCII drawing was rather screwed up, maybe too wide?)
Quoted 4 lines
I can limit the downstream with this:
tc qdisc add dev eth0 handle ffff:0 ingress
Quoted 8 lines
tc filter add dev eth0 parent ffff:0 protocol ip prio 5 handle 1 fw \
police rate 128kbit burst 128kbit mtu 1500 dropWhat I think I need is a separate filter for eth1 and eth2 that looks for different marks (handles?) Therefore, I need to mark packets coming through eth0 to eth1 with a
0x1and from eth0 to eth2 with a0x2and filter accordingly (I think).
I'm not sure I understand what you want, but I assume you want to limit the downstream from internet to the two internal masqu'ed subnets. With two extra conditions:
1 - internal traffic has priority (from subnet to subnet)
2 - internet downstream is equally divided between the subnets
First of all, I don't know how condition 2 can be met. I hope someone else can correct me.
For the rest, I propose the following setup:
1 - create for each internal interface a low and a high priority class
with low rates (unbounded)
2 - don't mark incoming packets from the external interface, but use the
u32 filter and match with the source address
3 - if the packet comes from a internal subnet, redirect it to the hi-prio
class, otherwise send it to the low-prio class
This might not be ideal, just an idea.
Signature · 8 lines
GnuPG public key: http://win-www.uia.ac.be/u/s965817/pub.key fingerprint = A3C4 DE50 712D 4FA8 C564 4D96 5E06 C9CC ECFA 19C5 Please edit the quoted text. _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/