Unnumbered
Hi,
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.
PSIkappa
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 5 lines · M.F. PSIkappa
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.
If I understand the ip unnumbered command correctly it allows you to share a single IP address on multiple interfaces. This is trivial on Linux: just add the same IP address to each of the interfaces with ip addr add
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
Doei, Arthur.
Signature · 8 lines
/\ / | [email protected] | Work like you don't need the money /__\ / | A friend is someone with whom | Love like you have never been hurt / \/__ | you can dare to be yourself | Dance like there's nobody watching _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 9 lines · Arthur van Leeuwen
Quoted 5 lines · M.F. PSIkappa
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.
Quoted 6 lines
If I understand the ip unnumbered command correctly it allows you to share a single IP address on multiple interfaces. This is trivial on Linux: just add the same IP address to each of the interfaces with ip addr add
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
Quoted 1 line
Doei, Arthur.
PSIkappa
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 18 lines · M.F. PSIkappa
Quoted 9 lines · Arthur van Leeuwen
Quoted 5 lines · M.F. PSIkappa
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.Quoted 6 lines
If I understand the ip unnumbered command correctly it allows you to share a single IP address on multiple interfaces. This is trivial on Linux: just add the same IP address to each of the interfaces with ip addr add
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
Quoted 8 lines
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
What is the difference with
192.168.0.1/24 [linux] 192.168.0.1 ------- 192.168.2.1 [linux] 192.168.2.1/24
if I may be so bold to ask? Yes, the routing effects may be different, and I mentioned that might be a problem, but the unnumbered thing looks like a cisco-specific hack...
Doei, Arthur.
Signature · 8 lines
/\ / | [email protected] | Work like you don't need the money /__\ / | A friend is someone with whom | Love like you have never been hurt / \/__ | you can dare to be yourself | Dance like there's nobody watching _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 22 lines · Arthur van Leeuwen
Quoted 13 lines
Quoted 6 lines
Quoted 5 lines
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.Quoted 6 lines
If I understand the ip unnumbered command correctly it allows you to share a single IP address on multiple interfaces. This is trivial on Linux: just add the same IP address to each of the interfaces with ip addr add
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
Quoted 8 lines
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
Quoted 7 lines
What is the difference with
192.168.0.1/24 [linux] 192.168.0.1 ------- 192.168.2.1 [linux] 192.168.2.1/24
if I may be so bold to ask? Yes, the routing effects may be different, and I mentioned that might be a problem, but the unnumbered thing looks like a cisco-specific hack...
Difference is in traceroute. Unnumbered is invisible, if I assign IP I see it in traceroute, but I can make hack that make this connection invisible, but it's rfc break ...
Yes, it's cisco specific hack.
Quoted 1 line
Doei, Arthur.
PSIkappa
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 11 lines · M.F. PSIkappa
Quoted 2 lines
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
So, in effect, you're changing the behaviour of your (level 3) port to a level 2 port, i.e., a switch, and add some filtering features to it, or am I missing something?
In that case, you might get away by configuring the two pairs of ports as ethernet bridge ports, and only assign IP-addresses to the two outer interfaces as in the diagram above.
Not sure whether all shaping and firewalling tricks will work in that case though. Anyone got a comment on that?
Regards,
Signature · 8 lines
Q_. Jasper Spaans <[email protected]> `~\ http://jsp.ds9a.nl/ Mr /\ Tel/Fax: +31-84-8749842 Zap Move '.sig' for great justice! _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 29 lines · Arthur van Leeuwen
Quoted 18 lines · M.F. PSIkappa
Quoted 9 lines · Arthur van Leeuwen
Quoted 5 lines · M.F. PSIkappa
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.Quoted 6 lines
If I understand the ip unnumbered command correctly it allows you to share a single IP address on multiple interfaces. This is trivial on Linux: just add the same IP address to each of the interfaces with ip addr add
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
Quoted 8 lines
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
Quoted 7 lines
What is the difference with
192.168.0.1/24 [linux] 192.168.0.1 ------- 192.168.2.1 [linux] 192.168.2.1/24
if I may be so bold to ask? Yes, the routing effects may be different, and I mentioned that might be a problem, but the unnumbered thing looks like a cisco-specific hack...
Sorry, it doesnt look so -- as far as i know unnumbered interfaces (PtoP connections) are supported by a number of vendors. Having a possibility to create unnumbered links under Linux would be nice, imho.
Quoted 12 lines
Doei, Arthur.
Signature · 8 lines
/\ / | [email protected] | Work like you don't need the money /__\ / | A friend is someone with whom | Love like you have never been hurt / \/__ | you can dare to be yourself | Dance like there's nobody watching _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Signature · 8 lines
Dmytro O. Redchuk http://www.popnet.kiev.ua System Administrator Phone: (380).44.495.26.05 PopNet Kommunikation Kiew Fax : (380).44.495.26.02 _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 28 lines · M.F. PSIkappa
Quoted 26 lines · Arthur van Leeuwen
Quoted 13 lines
Quoted 6 lines
Quoted 5 lines
it's posibility to make something similar to Cisco unnumber on Linux ? E. g.
interface Serial0
ip unnumbered Ethernet0
I don't want to assign to interface private IP.Quoted 6 lines
If I understand the ip unnumbered command correctly it allows you to share a single IP address on multiple interfaces. This is trivial on Linux: just add the same IP address to each of the interfaces with ip addr add
The routing effects I cannot correctly comment on, as I'm not sufficiently versed in IOS to fully grasp the effects of ip unnumbered
Quoted 8 lines
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
What is the difference with
192.168.0.1/24 [linux] 192.168.0.1 ------- 192.168.2.1 [linux] 192.168.2.1/24
Quoted 7 lines
Quoted 3 lines
if I may be so bold to ask? Yes, the routing effects may be different, and I mentioned that might be a problem, but the unnumbered thing looks like a cisco-specific hack...
Difference is in traceroute. Unnumbered is invisible, if I assign IP I see it in traceroute, but I can make hack that make this connection invisible, but it's rfc break ...
Ah, but iptable's mangle module will let you play around with the TTL field of packets being forwarded through a linux box. Yes, it takes some more configuring, but the behaviour can be duplicated. And that is not considered a hack. Besides, ever heard of masquerading? That is nowhere near RFC compliance... and should theoretically be impossible, if I'm to believe Jos Vos (one of the first implementers).
Doei, Arthur.
Signature · 8 lines
/\ / | [email protected] | Work like you don't need the money /__\ / | A friend is someone with whom | Love like you have never been hurt / \/__ | you can dare to be yourself | Dance like there's nobody watching _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 13 lines · M.F. PSIkappa
Quoted 13 lines
Quoted 8 lines
No, it's incorrect, unnumberd allow you to connect 2 router without IP adresses.
192.168.0.1/24 [cisco]unnumbered-----unnumberd[cisco] 192.168.2.1/24
It's special case of point-to-point connection. In linux if I make point-to-point connection I have to assign any IP on both endpoint of connection.
What is the difference with
192.168.0.1/24 [linux] 192.168.0.1 ------- 192.168.2.1 [linux] 192.168.2.1/24
Quoted 7 lines
Quoted 3 lines
if I may be so bold to ask? Yes, the routing effects may be different, and I mentioned that might be a problem, but the unnumbered thing looks like a cisco-specific hack...
Difference is in traceroute. Unnumbered is invisible, if I assign IP I see it in traceroute, but I can make hack that make this connection invisible, but it's rfc break ...
This is correct, in the workings... But I don't think it really breaks the RFC's...
Anyways this is the diffrence:
All networks prefixed with "10.0"...
Numbered:
----- 10.0.1.1/24 [[[Linux Box]]] 10.0.0.100/24 -----Ethernet----- 10.0.2.1/24 [[[Linux Box]]] 10.0.0.200/24 -----
Unnumbered:
----- 10.0.1.1/24 [[[Linux Box]]] -----P to P----- [[[Linux Box]]] 10.0.0.200/24 -----
As you can see, the unnumbered is a Point to Point connection, and acts more like a "bridge"...
Actually, if you want to do an Unnumbered connection with two Ethernet Interfaces, thats exactly how I would set it up... as a Bridge. Either that or use PPPoE and that should be able to do something simular.
Quoted 1 line
Yes, it's cisco specific hack.
No this is not true... Alot of the Point to Point (IE: Dial-Up, ISDN) type Internet Connections use Unnumbered Connections. There are a large number of companies that support these type of connections.
--Greg.
-------------------------------------
Greg Varga
Owner: Digital Realities
http://www.digital.realities.com
604.576.2219
Lead Programmer of MUTAG
http://www.bvcompuworks.com/mutag
Network Administrator
-------------------------------------
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 2 lines · Greg Varga
This is correct, in the workings... But I don't think it really breaks the RFC's...
It has nothing to do with the RFC's.
Quoted 20 lines
Anyways this is the diffrence:
All networks prefixed with "10.0"...
Numbered:
----- 10.0.1.1/24 [[[Linux Box]]] 10.0.0.100/24 -----Ethernet----- 10.0.2.1/24 [[[Linux Box]]] 10.0.0.200/24 -----Unnumbered:
----- 10.0.1.1/24 [[[Linux Box]]] -----P to P----- [[[Linux Box]]] 10.0.0.200/24 -----As you can see, the unnumbered is a Point to Point connection, and acts more like a "bridge"...
Actually, if you want to do an Unnumbered connection with two Ethernet Interfaces, thats exactly how I would set it up... as a Bridge. Either that or use PPPoE and that should be able to do something simular.
Quoted 5 lines
Quoted 1 line
Yes, it's cisco specific hack.
No this is not true... Alot of the Point to Point (IE: Dial-Up, ISDN) type Internet Connections use Unnumbered Connections. There are a large number of companies that support these type of connections.
You are correct, Greg. Unnumbered interfaces are (mostly) ptp interfaces. When setting up a ptp interface you should usually use one /30 in a traditional way. Now, for a ptp connection there is only one IP entity at the other end and it doesn't have to be one out of a /30. Any IP address will do. That's why they usually use the loopback IP (or the IP of another interface) to identify the Unnumbered interface.
I'm not sure how this can be done with linux. But I think that pppd program does not require you to waste one /30 for the link. The server side can send one /32 to the client side and announce another IP (eg, the IP of its ethernet interface) as the peer IP of the ppp link. At least this is what's happening when you dial in to a NAS.
Ramin
Quoted 2 lines
--Greg.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/