Skip to contentSkip to conversation

2.4.4 stability on Lions

Linux-ia64 Michael Madore 7 participants 14 messages May 22, 2001 – May 23, 2001

lore
Share & tools
lore
#0 lore raw

Hi,

Has anyone seem any instability with the 2.4.4 kernel + David's patch on Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups after a short time. Usually I get a totally black screen. I'm going to try 2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203
#1 lore raw

I have been running the SuSE 7.2 beta (2.4.4) on a Lion for about a week now. I don't remember what BIOS I have but I'll find out.

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 1:19 PM
To: [email protected]
Subject: [Linux-ia64] 2.4.4 stability on Lions

Hi,

Has anyone seem any instability with the 2.4.4 kernel + David's patch on Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups after a short time. Usually I get a totally black screen. I'm going to try 2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
#2 lore raw
In reply to Michael Madore
Quoted 10 lines

Has anyone seem any instability with the 2.4.4 kernel + David's patch on
Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups
after a short time. Usually I get a totally black screen. I'm going to try
2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

I had one lockup after about 18 hours of heavy stress copy-and-compare and NIC traffic last night.
4P C0, Lion B2 board set, BIOS 80. Black screen, no magic sysrq. I'm trying to reproduce it now.

Under normal light loads I haven't seen any issues.

Thanks,
Matt

--
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux

#3 lore raw
In reply to Michael Madore

I just noticed that the machine locked up on me while sitting at the EFI shell prompt. I've downloaded BIOS 76 (latest available on Quad) and I'll see if that makes any difference.

Quoted 26 lines · On Tue, May 22, 2001 at 04:06:30PM -0500, [email protected] wrote:
Quoted 10 lines

Has anyone seem any instability with the 2.4.4 kernel + David's patch on
Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups
after a short time. Usually I get a totally black screen. I'm going to try
2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

I had one lockup after about 18 hours of heavy stress copy-and-compare and NIC traffic last night.
4P C0, Lion B2 board set, BIOS 80. Black screen, no magic sysrq. I'm trying to reproduce it now.

Under normal light loads I haven't seen any issues.

Thanks,
Matt

--
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux

Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203
#4 lore raw
In reply to Michael Madore

While it is true you should always use the latest BIOS that matches your processor stepping ( in this case 76 ). The solution to your problem is to alter your SCSI host adapter settings to operate > 4GB. If you can use the SCSI FastUtil the setting to change is found under host adapter settings.
Hope this helps.

Don Wiegrefe
Soft Sur/ Lion Hardware/BIOS Support

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 2:58 PM
To: [email protected]
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

I just noticed that the machine locked up on me while sitting at the EFI shell prompt. I've downloaded BIOS 76 (latest available on Quad) and I'll see if that makes any difference.

Quoted 26 lines · On Tue, May 22, 2001 at 04:06:30PM -0500, [email protected] wrote:
Quoted 10 lines

Has anyone seem any instability with the 2.4.4 kernel + David's patch on
Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups
after a short time. Usually I get a totally black screen. I'm going to try
2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

I had one lockup after about 18 hours of heavy stress copy-and-compare and NIC traffic last night.
4P C0, Lion B2 board set, BIOS 80. Black screen, no magic sysrq. I'm trying to reproduce it now.

Under normal light loads I haven't seen any issues.

Thanks,
Matt

--
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux

Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
#5 lore raw
In reply to Michael Madore

Hmmm, I'll check that out. I know that the adapter settings were originally set to > 4GB. Not sure how they would have been altered.

Quoted 59 lines · Don J

While it is true you should always use the latest BIOS that matches your processor stepping ( in this case 76 ). The solution to your problem is to alter your SCSI host adapter settings to operate > 4GB. If you can use the SCSI FastUtil the setting to change is found under host adapter settings.
Hope this helps.

Don Wiegrefe
Soft Sur/ Lion Hardware/BIOS Support

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 2:58 PM
To: [email protected]
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

I just noticed that the machine locked up on me while sitting at the EFI shell prompt. I've downloaded BIOS 76 (latest available on Quad) and I'll see if that makes any difference.

Quoted 26 lines · On Tue, May 22, 2001 at 04:06:30PM -0500, [email protected] wrote:
Quoted 10 lines

Has anyone seem any instability with the 2.4.4 kernel + David's patch on
Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups
after a short time. Usually I get a totally black screen. I'm going to try
2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

I had one lockup after about 18 hours of heavy stress copy-and-compare and NIC traffic last night.
4P C0, Lion B2 board set, BIOS 80. Black screen, no magic sysrq. I'm trying to reproduce it now.

Under normal light loads I haven't seen any issues.

Thanks,
Matt

--
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux

Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203
#6 lore raw
In reply to Michael Madore
Quoted 5 lines

The solution to your problem is to
alter your SCSI host adapter settings to operate > 4GB. If you can use the
SCSI FastUtil the setting to change is found under host adapter settings.

The Linux qla1280 v3.23 driver as distributed in the IA-64 patch *always* sets a 64-bit dma_mask if running on a 64-bit processor. The NVRAM bit isn't read as the switch anymore.

#if BITS_PER_LONG > 32
    /* Enable 64bit addressing for OS/System combination supporting it   */
    /* actual NVRAM bit is: nv->cntr_flags_1.enable_64bit_addressing     */
    /* but we will ignore it and use BITS_PER_LONG macro to setup for    */
    /* 64 or 32 bit access of host memory in all x86/ia-64/Alpha systems */
    ha->flags.enable_64bit_addressing = 1;
#else
    ha->flags.enable_64bit_addressing = 0;

#endif

#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,3,18)
    if (ha->flags.enable_64bit_addressing) {
      printk("[[[ qla1x160: 64 Bit PCI Addressing Enabled ]]]\n");
#if BITS_PER_LONG > 32
           /* Update our PCI device dma_mask for full 64 bit mask */
           //ha->pdev->dma_mask = (pci_dma_t) 0xffffffffffffffffull;
           ha->pdev->dma_mask =  0xffffffffffffffff;
#endif
    }

#endif

Jes cleaned this up a bit with his patch:

+ pci_set_dma_mask(ha->pdev, (dma_addr_t)~0ULL);

Thanks,
Matt

Signature · 4 lines
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux
Quoted 82 lines

-----Original Message-----
From: Wiegrefe, Don J [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 5:34 PM
To: 'Michael Madore'; [email protected]
Cc: [email protected]
Subject: RE: [Linux-ia64] 2.4.4 stability on Lions

While it is true you should always use the latest BIOS that matches your
processor stepping ( in this case 76 ). The solution to your problem is to
alter your SCSI host adapter settings to operate > 4GB. If you can use the
SCSI FastUtil the setting to change is found under host adapter settings.
Hope this helps.

Don Wiegrefe
Soft Sur/ Lion Hardware/BIOS Support

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 2:58 PM
To: [email protected]
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

I just noticed that the machine locked up on me while sitting at the EFI
shell prompt. I've downloaded BIOS 76 (latest available on Quad) and I'll
see if that makes any difference.

Quoted 11 lines · On Tue, May 22, 2001 at 04:06:30PM -0500, [email protected] wrote:
Quoted 10 lines

Has anyone seem any instability with the 2.4.4 kernel + David's patch on
Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups
after a short time. Usually I get a totally black screen. I'm going to try
2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

Quoted 1 line

I had one lockup after about 18 hours of heavy stress

copy-and-compare and

Quoted 2 lines

NIC traffic last night.
4P C0, Lion B2 board set, BIOS 80. Black screen, no magic

sysrq. I'm

Quoted 12 lines

trying to reproduce it now.

Under normal light loads I haven't seen any issues.

Thanks,
Matt

--
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux

Signature · 15 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64


_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
#7 lore raw
In reply to Michael Madore

Turns out that my upgrade to C0 processors reset my SCSI controller to 32 bit addressing. I've set it back to 64 bit and now everything seems to be working ok.

Well, almost everything. I still have the problem with the onboard e100 network adapter. This is the problem where transferring certain files via nfs causes nfs to die. I don't know if there was ever a resolution to this.

Quoted 132 lines · On Tue, May 22, 2001 at 08:34:13PM -0500, [email protected] wrote:
Quoted 5 lines

The solution to your problem is to
alter your SCSI host adapter settings to operate > 4GB. If you can use the
SCSI FastUtil the setting to change is found under host adapter settings.

The Linux qla1280 v3.23 driver as distributed in the IA-64 patch *always* sets a 64-bit dma_mask if running on a 64-bit processor. The NVRAM bit isn't read as the switch anymore.

#if BITS_PER_LONG > 32
    /* Enable 64bit addressing for OS/System combination supporting it   */
    /* actual NVRAM bit is: nv->cntr_flags_1.enable_64bit_addressing     */
    /* but we will ignore it and use BITS_PER_LONG macro to setup for    */
    /* 64 or 32 bit access of host memory in all x86/ia-64/Alpha systems */
    ha->flags.enable_64bit_addressing = 1;
#else
    ha->flags.enable_64bit_addressing = 0;

#endif

#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,3,18)
    if (ha->flags.enable_64bit_addressing) {
      printk("[[[ qla1x160: 64 Bit PCI Addressing Enabled ]]]\n");
#if BITS_PER_LONG > 32
           /* Update our PCI device dma_mask for full 64 bit mask */
           //ha->pdev->dma_mask = (pci_dma_t) 0xffffffffffffffffull;
           ha->pdev->dma_mask =  0xffffffffffffffff;
#endif
    }

#endif

Jes cleaned this up a bit with his patch:

+ pci_set_dma_mask(ha->pdev, (dma_addr_t)~0ULL);

Thanks,
Matt

Signature · 4 lines
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux
Quoted 82 lines

-----Original Message-----
From: Wiegrefe, Don J [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 5:34 PM
To: 'Michael Madore'; [email protected]
Cc: [email protected]
Subject: RE: [Linux-ia64] 2.4.4 stability on Lions

While it is true you should always use the latest BIOS that matches your
processor stepping ( in this case 76 ). The solution to your problem is to
alter your SCSI host adapter settings to operate > 4GB. If you can use the
SCSI FastUtil the setting to change is found under host adapter settings.
Hope this helps.

Don Wiegrefe
Soft Sur/ Lion Hardware/BIOS Support

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Tuesday, May 22, 2001 2:58 PM
To: [email protected]
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

I just noticed that the machine locked up on me while sitting at the EFI
shell prompt. I've downloaded BIOS 76 (latest available on Quad) and I'll
see if that makes any difference.

Quoted 11 lines · On Tue, May 22, 2001 at 04:06:30PM -0500, [email protected] wrote:
Quoted 10 lines

Has anyone seem any instability with the 2.4.4 kernel + David's patch on
Lions? I have been running it successfully on a 2P C0 Big Sur with BIOS
103. On a 4P C0 Lion with BIOS 73, however, I consistantly get lockups
after a short time. Usually I get a totally black screen. I'm going to try
2.4.3 and see if I still see the same problem. 2.4.2 seem to work fine.

Quoted 1 line

I had one lockup after about 18 hours of heavy stress

copy-and-compare and

Quoted 2 lines

NIC traffic last night.
4P C0, Lion B2 board set, BIOS 80. Black screen, no magic

sysrq. I'm

Quoted 12 lines

trying to reproduce it now.

Under normal light loads I haven't seen any issues.

Thanks,
Matt

--
Matt Domsch
Sr. Software Engineer
Dell Linux Solutions
www.dell.com/linux

Signature · 15 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64


_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203
#8 lore raw
In reply to Michael Madore
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line · Michael Madore

Michael> Well, almost everything. I still have the problem with the Michael> onboard e100 network adapter. This is the problem where Michael> transferring certain files via nfs causes nfs to die.

Die or "get stuck"? It shouldn't die.

	--david
#9 lore raw
In reply to Michael Madore

What I meant to say was it gets violently ill. ;-)

You are correct, it "get's stuck" It is the same problem that was discussed on the list in February.

Quoted 9 lines · David Mosberger
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line · Michael Madore

Michael> Well, almost everything. I still have the problem with the Michael> onboard e100 network adapter. This is the problem where Michael> transferring certain files via nfs causes nfs to die.

Die or "get stuck"? It shouldn't die.

	--david
Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203
#10 lore raw
In reply to Michael Madore

Mike,

A workaround should be implemented and I will need to investigate on this. In the mean time you can use an add-on Intel 10/100 ethernet card and this problem is not present.

Thanks,
Asit

Quoted 38 lines

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Wednesday, May 23, 2001 11:23 AM
To: David Mosberger
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

What I meant to say was it gets violently ill. ;-)

You are correct, it "get's stuck" It is the same problem that was discussed
on the list in February.

Quoted 1 line · David Mosberger
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

On Wed, 23 May 2001 09:43:10 -0700, Michael Madore

Quoted 2 lines · <[email protected]> said:

Michael> Well, almost everything. I still have the

problem with the

Quoted 6 lines

Michael> onboard e100 network adapter. This is the problem where Michael> transferring certain files via nfs causes nfs to die.

Die or "get stuck"? It shouldn't die.

	--david
Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
#11 lore raw
In reply to Michael Madore

Thanks Asit. Is there a way to temporarily disable the on board NIC? Our installer always defaults to eth0 for network installs. As luck would have it, the e100 modules get loaded before our add in 3com.

Quoted 54 lines · Asit K

Mike,

A workaround should be implemented and I will need to investigate on this. In the mean time you can use an add-on Intel 10/100 ethernet card and this problem is not present.

Thanks,
Asit

Quoted 18 lines

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Wednesday, May 23, 2001 11:23 AM
To: David Mosberger
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

What I meant to say was it gets violently ill. ;-)

You are correct, it "get's stuck" It is the same problem that was discussed
on the list in February.

Quoted 1 line · David Mosberger
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

On Wed, 23 May 2001 09:43:10 -0700, Michael Madore

Quoted 1 line · <[email protected]> said:
Quoted 20 lines
Quoted 1 line

Michael> Well, almost everything. I still have the

problem with the

Quoted 6 lines

Michael> onboard e100 network adapter. This is the problem where Michael> transferring certain files via nfs causes nfs to die.

Die or "get stuck"? It shouldn't die.

	--david
Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64

Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203
#12 lore raw
In reply to Michael Madore
Quoted 6 lines

Thanks Asit. Is there a way to temporarily disable the on board NIC? Our
installer always defaults to eth0 for network installs. As luck would have
it, the e100 modules get loaded before our add in 3com.

If you build a kernel with the 3com driver linked in (not a module), and don't configure in the e100, it should work. I just did that with a Tulip card and it's working.

David

Quoted 84 lines

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Wednesday, May 23, 2001 1:54 PM
To: Mallick, Asit K
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

Thanks Asit. Is there a way to temporarily disable the on board NIC? Our
installer always defaults to eth0 for network installs. As luck would have
it, the e100 modules get loaded before our add in 3com.

Quoted 3 lines · Asit K

Mike,

A workaround should be implemented and I will need to

investigate on this.

Quoted 1 line

In the mean time you can use an add-on Intel 10/100

ethernet card and this

Quoted 27 lines

problem is not present.

Thanks,
Asit

Quoted 21 lines

-----Original Message-----
From: Michael Madore [mailto:[email protected]]
Sent: Wednesday, May 23, 2001 11:23 AM
To: David Mosberger
Cc: [email protected]
Subject: Re: [Linux-ia64] 2.4.4 stability on Lions

What I meant to say was it gets violently ill. ;-)

You are correct, it "get's stuck" It is the same problem that was discussed
on the list in February.

Quoted 1 line · David Mosberger
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

On Wed, 23 May 2001 09:43:10 -0700, Michael Madore

Quoted 2 lines · <[email protected]> said:

Michael> Well, almost everything. I still have the

problem with the

Quoted 1 line

Michael> onboard e100 network adapter. This is the

problem where

Quoted 23 lines
Quoted 17 lines
Quoted 5 lines

Michael> transferring certain files via nfs causes nfs to die.

Die or "get stuck"? It shouldn't die.

	--david
Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64

Signature · 9 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203

_______________________________________________
Linux-IA64 mailing list
[email protected]
http://lists.linuxia64.org/lists/listinfo/linux-ia64
#13 lore raw
In reply to Michael Madore

Unfortunately, this is for an install CD, so I can't statically link in a driver.

Quoted 12 lines · David G
Quoted 6 lines

Thanks Asit. Is there a way to temporarily disable the on board NIC? Our
installer always defaults to eth0 for network installs. As luck would have
it, the e100 modules get loaded before our add in 3com.

If you build a kernel with the 3com driver linked in (not a module), and don't configure in the e100, it should work. I just did that with a Tulip card and it's working.

David

Signature · 4 lines
Mike Madore
Senior Software Engineer
TurboLinux, Inc.
(650)228-5203