SB16
Hi all,
I am still having problems with configuring my SB16 sound card. I am using Slakware with kernal 2.0.30. I compile the kernal with
Sound ? M
support for /dev/dsp and /dev/audio ? Y
Other I put N. I use the isapnptools_1.17 to configure, I read the
manual, readme, and HOW-TO, tring a few times. Still unable to setup my sound card.
(One thing good with Windows'95, the driver is really easy to
install, linux must improve with these)
Nottingham said that my dirver(Sound Driver:3.5.4-960630) is the old
one, will this old one work with SB16? Or how could I get the new sound driver?
The below that show on my Linux:-
% isapnp /etc/isapnp.conf
Board 1 has Identity d7 00 00 15 f5 24 00 8c 0e: CTL0024 Serial No 5621 [checksum d7]
CTL0024/5621[0]{Audio }: Ports 0x220 0x330 0x388; IRQ5 DMA1
DMA5 --- Enabled OK
% insmod sound
(I did check sound module was not loaded before this)
% lsmod
Module: #pages: Used by:
sound 10 0
ppp 5 0 slip 2 0 slhc 2 [ppp slip] 0 lp 2 0
BUT
% cat /dev/sndstat
Sound Driver:3.5.4-960630 (Tue Mar 2 05:22:12 SGT 1999 root,
Config options: 0
Installed drivers:
Card config:
Audio devices:
Synth devices: NOT ENABLED IN CONFIG
Midi devices: NOT ENABLED IN CONFIG
Timers:
Mixers:
So I can't use the device, what is going wrong?
Quoted 9 lines
Hi all,
I am still having problems with configuring my SB16 sound card. I am using Slakware with kernal 2.0.30. I compile the kernal with
Sound ? M
support for/dev/dspand/dev/audio? YOther I put N.
You must also enable Sound Blaster support!
While you do that I suggest that you also enable the sequencer part and be able to play MIDI files.
Consider upgrading to a more recent kernel (2.2.x).
Itai
Quoted 19 lines · On Thu, 13 May 1999 [email protected] wrote:
Hi all,
I am still having problems with configuring my SB16 sound card. I am using Slakware with kernal 2.0.30. I compile the kernal with
Sound ? M
support for/dev/dspand/dev/audio? YOther I put N. I use the isapnptools_1.17 to configure, I read the
manual, readme, and HOW-TO, tring a few times. Still unable to setup my sound card.(One thing good with Windows'95, the driver is really easy to
install, linux must improve with these)Nottingham said that my dirver(Sound Driver:3.5.4-960630) is the old
one, will this old one work with SB16? Or how could I get the new sound driver?
Quoted 8 lines
The below that show on my Linux:-
% isapnp
/etc/isapnp.confBoard 1 has Identity d7 00 00 15 f5 24 00 8c 0e: CTL0024 Serial No 5621 [checksum d7]
CTL0024/5621[0]{Audio }: Ports0x2200x3300x388; IRQ5 DMA1
DMA5 --- Enabled OK
I had bios probs with this part. Usually it would tell me the device wasn't available or some such. I moved to a different irq and the probs went away.
options sb io=0x220 irq=9 dma=1 dma16=5 mpu_io=0x330
Nothing else was at 5, but I couldn't use it for sound.
ciao,
der.hans
Quoted 27 lines
% insmod sound
(I did check sound module was not loaded before this)% lsmod
Module: #pages: Used by:
sound 10 0ppp 5 0 slip 2 0 slhc 2 [ppp slip] 0 lp 2 0BUT
% cat/dev/sndstatSound Driver:3.5.4-960630 (Tue Mar 2 05:22:12 SGT 1999 root,
Config options: 0
Installed drivers:
Card config:
Audio devices:
Synth devices: NOT ENABLED IN CONFIG
Quoted 9 lines
Midi devices: NOT ENABLED IN CONFIG
Timers:
Mixers:
So I can't use the device, what is going wrong?
# +++++++++++=================+++++++++++ #
# [email protected] # # http://home.pages.de/~lufthans/ # # I've got a photographic memory, # # but I'm lousy photographer. - der.hans #
# ======+++++++++++++++++++++++++++++++++====== #
Quoted 2 lines · On Thu, May 13, 1999 at 11:48:20AM +0800, [email protected] wrote:
(One thing good with Windows'95, the driver is really easy to
install, linux must improve with these)
Then you could have choosen a more user-friendly distribution than Slackware.
The ALSA project has also improved the simplicity of configuration (including isapnp autoconfiguration).
-Michele