Skip to contentSkip to conversation

AWE64 ISA PnP Midi pbm

DISCUSSION Soulier, Frederic 1 participant 1 message Jun 4, 1999 Sound

lore
Share & tools
lore
#0 lore raw
Quoted 8 lines · Paco

Hi Frederic
Could you please send me a copy of your /etc/isapnp.conf? There may be some info missing from there.

The AWE64 has a hardware bug that causes it to not report all of the necessary isapnp information. In particular, the wave table of the AWE64 doesn't get initialized properly.
-Paco

Here is my /etc/isapnp.conf
If you do not get it correctly I can try to send it as an attachment.

# $Id: pnpdump.c,v 1.17 1998/11/10 22:45:04 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK #
# For details of this file format, see isapnp.conf(5) #
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR #
# Trying port address 0203
# Board 1 has serial identifier b0 1f 81 7f 99 c7 00 8c 0e

# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier b0 1f 81 7f 99 c7 00 8c 0e)
# Vendor Id CTL00c7, Serial Number 528580505, checksum 0xB0.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative AWE64 PnP<--
# Vendor defined tag: 73 02 45 02
#
# Logical device id CTL0045
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00c7/528580505 (LD 0
# ANSI string -->Audio<--

# Multiple choice time, choose one only !

# Start dependent functions: priority preferred
# IRQ 7.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 7 (MODE +E)))
# First DMA channel 1.

#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
#       Next DMA channel 5.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
(DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 1 bytes
#             Number of IO addresses required: 16
(IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
(IO 1 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4

(IO 2 (SIZE 4) (BASE 0x0388))
# End dependent functions
(NAME "CTL00c7/528580505[0]{Audio }")
(ACT Y)))
#
# Logical device id CTL0022
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00c7/528580505 (LD 2
# ANSI string -->WaveTable<--

# Multiple choice time, choose one only !

# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines

#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0620
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4

(IO 0 (SIZE 4) (BASE 0x0620))

# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines

#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0680
#             IO base alignment 32 bytes
#             Number of IO addresses required: 4

(IO 1 (SIZE 4) (BASE 0x0A20))

# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines

#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0680
#             IO base alignment 32 bytes
#             Number of IO addresses required: 4

(IO 2 (SIZE 4) (BASE 0x0E20))

# End dependent functions
# Vendor defined tag: 75 01 03 46 ca 8a
(NAME "CTL00c7/528580505[2]{WaveTable }")
(ACT Y)))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

Ciao
Fred