Reducing "noise" from output
Hi, Bryan.
I wanted to ask you what kernel/distribution/drivers you are using. I also have the AWE64 in my box, but I have no problems with hiss. I *do* use the line-out instead of the speaker-out, so that may have something to do with it, but it seems unlikely.
-Paco
Quoted 8 lines · Bryan Scaringe
Hello all,
I have a SB-AWE64, and it works fine under Linux, but I was
wondering if there is any way to reduce the noise from the speaker-output. It sounds like a tape hiss, only less so.Thanks,
Bryan
It might be due to power connections and other connections in close proximity to the card, and/or the cord for the speakerOut. If the main power cord to the computer must cross the outputs, put them at a 90 degree angle to the power cord. or better yet, dont cross them at all. 110, or 220 power cords have a large magnetic field that generates noise on speaker cords.
Quoted 14 lines
Hi, Bryan.
I wanted to ask you what
kernel/distribution/driversyou are using. I also have the AWE64 in my box, but I have no problems with hiss. I *do* use the line-out instead of the speaker-out, so that may have something to do with it, but it seems unlikely.-Paco
Quoted 3 lines · Bryan Scaringe
Hello all,
I have a SB-AWE64, and it works fine under Linux, but I was wondering if there is any way to reduce the noise from the
speaker-output.
Quoted 7 lines
Quoted 5 lines
It sounds like a tape hiss, only less so.
Thanks,
Bryan
Yep. The hiss is gone using line-out. I guess this next question may be a bit off topic, but here goes:
speaker-out is considerably louder at a given volume level than line-out. speaker-out also seems to have better quality bass. line-out however, seems to be much cleaner, lacking the hiss.
So: What is the difference between line-out and speaker-out, specificly from a functional standpoint. Is line-out expected to be sent to an amplifier that will control bass/treble/vol? Is this why line-out is less responsive to bass/treble changes using "aumix" than speaker-out?
Thanks,
Bryan
Quoted 22 lines
Hi, Bryan.
I wanted to ask you what
kernel/distribution/driversyou are using. I also have the AWE64 in my box, but I have no problems with hiss. I *do* use the line-out instead of the speaker-out, so that may have something to do with it, but it seems unlikely.-Paco
Quoted 8 lines · Bryan Scaringe
Hello all,
I have a SB-AWE64, and it works fine under Linux, but I was
wondering if there is any way to reduce the noise from the speaker-output. It sounds like a tape hiss, only less so.Thanks,
Bryan
Quoted 3 lines · Bryan Scaringe
So: What is the difference between line-out and speaker-out, specificly from a functional standpoint. Is line-out expected to be sent to an amplifier that will control bass/treble/vol?
Exactly. For line-out, you have minimal control over the amplitude of the signal. "Line-level" voltage is (I believe) 2.2V, peak-to-peak. Volume control of line-out allows you to change this peak-to-peak value, but not significantly.
Line-out signals are meant to go to another device which will control the bass/treble/volume. (ie, your stereo)
Speaker-out signals are amplified *on-the-card* and provide enough juice to power speakers themselves. This on-card amplification may be the cause of your hiss. (I'm not too sure if the on-card amplifiers are very high-quality on an AWE64.)
Quoted 2 lines
Is this why line-out is less responsive to bass/treble changes using "aumix" than speaker-out?
BINGO! Bass and treble controls function just like the volume control for line-out; they *do* cause changes in the signal, but not significant ones. You can think of bass and treble controls as "turning up the volume" of the low or high EQ bands.
regards,
Chad "Paco" Walker