OMAP3:zoom2: Add support for OMAP3 Zoom2 board
Subsystems (3)
PATCH v4 1/3 OMAP3:zoom2: Add support for OMAP3 Zoom2 board
From: Vikram Pandita <[email protected]>
This patch creates the minimal OMAP3 Zoom2 board support.
Signed-off-by Mikkel Christensen <[email protected]>
Signed-off-by Vikram Pandita <[email protected]>
Acked-by Kevin Hilman <[email protected]>
--- arch/arm/mach-omap2/board-zoom-debugboard.c | 160 +++++++++++++++++++++++++++ arch/arm/mach-omap2/board-zoom2.c | 110 ++++++++++++++++++ 2 files changed, 270 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-omap2/board-zoom-debugboard.c create mode 100644 arch/arm/mach-omap2/board-zoom2.c
arch/arm/mach-omap2/board-zoom-debugboard.c new file +160 -0
@@ -0,0 +1,160 @@ +/* +* Copyright (C) 2009 Texas Instruments Inc. +* Mikkel Christensen <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/serial_8250.h> +#include <linux/smsc911x.h> + +#include <mach/gpio.h> +#include <mach/gpmc.h> + +#define ZOOM2_SMSC911X_CS 7 +#define ZOOM2_SMSC911X_GPIO 158 +#define ZOOM2_QUADUART_CS 3 +#define ZOOM2_QUADUART_GPIO 102 +#define QUART_CLK 1843200 +#define DEBUG_BASE 0x08000000 +#define ZOOM2_ETHR_START DEBUG_BASE + +static struct resource zoom2_smsc911x_resources[] = { + [0 ] = { + .start =ZOOM2_ETHR_START , + .end =ZOOM2_ETHR_START +SZ_4K , + .flags =IORESOURCE_MEM , + }, + [1 ] = { + .flags =IORESOURCE_IRQ |IORESOURCE_IRQ_LOWLEVEL , + }, +}; + +static struct smsc911x_platform_config zoom2_smsc911x_config = { + .irq_polarity =SMSC911X_IRQ_POLARITY_ACTIVE_LOW , + .irq_type =SMSC911X_IRQ_TYPE_OPEN_DRAIN , + .flags =SMSC911X_USE_32BIT , + .phy_interface =PHY_INTERFACE_MODE_MII , +}; + +static struct platform_device zoom2_smsc911x_device = { + .name ="smsc911x" , + .id =-1 , + .num_resources =ARRAY_SIZE (zoom2_smsc911x_resources), + .resource = zoom2_smsc911x_resources, + .dev = { + .platform_data = &zoom2_smsc911x_config, + }, +}; + +static inline void __init zoom2_init_smsc911x (void ) +{ +int eth_cs; +unsigned long cs_mem_base; +int eth_gpio =0 ; + + eth_cs =ZOOM2_SMSC911X_CS ; + +if (gpmc_cs_request (eth_cs,SZ_16M , &cs_mem_base) <0 ) { +printk (KERN_ERR "Failed to request GPMC mem for smsc911x\n" ); +return ; + } + + zoom2_smsc911x_resources[0 ].start = cs_mem_base +0x0 ; + zoom2_smsc911x_resources[0 ].end = cs_mem_base +0xff ; + + eth_gpio =ZOOM2_SMSC911X_GPIO ; + + zoom2_smsc911x_resources[1 ].start =OMAP_GPIO_IRQ (eth_gpio); + +if (gpio_request (eth_gpio,"smsc911x irq" ) <0 ) { +printk (KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n" , + eth_gpio); +return ; + } +gpio_direction_input (eth_gpio); +} + +static struct plat_serial8250_port serial_platform_data[] = { + { + .mapbase =0x10000000 , + .irq =OMAP_GPIO_IRQ (102 ), + .flags =UPF_BOOT_AUTOCONF |UPF_IOREMAP |UPF_SHARE_IRQ , + .iotype =UPIO_MEM , + .regshift =1 , + .uartclk =QUART_CLK , + }, { + .flags =0 + } +}; + +static struct platform_device zoom2_debugboard_serial_device = { + .name ="serial8250" , + .id =PLAT8250_DEV_PLATFORM1 , + .dev = { + .platform_data = serial_platform_data, + }, +}; + +static inline void __init zoom2_init_quaduart (void ) +{ +int quart_cs; +unsigned long cs_mem_base; +int quart_gpio =0 ; + + quart_cs =ZOOM2_QUADUART_CS ; + +if (gpmc_cs_request (quart_cs,SZ_1M , &cs_mem_base) <0 ) { +printk (KERN_ERR "Failed to request GPMC mem" +"for Quad UART(TL16CP754C)\n" ); +return ; + } + + quart_gpio =ZOOM2_QUADUART_GPIO ; + +if (gpio_request (quart_gpio,"TL16CP754C GPIO" ) <0 ) { +printk (KERN_ERR "Failed to request GPIO%d for TL16CP754C\n" , + quart_gpio); +return ; + } +gpio_direction_input (quart_gpio); +} + +static inline int omap_zoom2_debugboard_detect (void ) +{ +int debug_board_detect =0 ; + + debug_board_detect =ZOOM2_SMSC911X_GPIO ; + +if (gpio_request (debug_board_detect,"Zoom2 debug board detect" ) <0 ) { +printk (KERN_ERR "Failed to request GPIO%d for Zoom2 debug" +"board detect\n" , debug_board_detect); +return 0 ; + } +gpio_direction_input (debug_board_detect); + +if (!gpio_get_value (debug_board_detect)) { +gpio_free (debug_board_detect); +return 0 ; + } +return 1 ; +} + +static struct platform_device *zoom2_devices[]__initdata = { + &zoom2_smsc911x_device, + &zoom2_debugboard_serial_device, +}; + +int __init omap_zoom2_debugboard_init (void ) +{ +if (!omap_zoom2_debugboard_detect ()) +return 0 ; + +zoom2_init_smsc911x (); +zoom2_init_quaduart (); +return platform_add_devices (zoom2_devices,ARRAY_SIZE (zoom2_devices)); +}
arch/arm/mach-omap2/board-zoom2.c new file +110 -0
110 lines not on this page · raw message
Signature · 1 line
1.6.0.3.613.g9f8f13
Tony Lindgren
maintainerPATCH v4 1/3 OMAP3:zoom2: Add support for OMAP3 Zoom2 board
This patch has been applied to the linux-omap
by youw fwiendly patch wobot.
Initial commit ID (Likely to change): 4e1030fe8519ba6d6e82a36e1b7a8ca23f78b079
PatchWorks
http://patchwork.kernel.org/patch/25135/
Git (Likely to change, and takes a while to get mirrored)
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=4e1030fe8519ba6d6e82a36e1b7a8ca23f78b079