usb patches accepted by Greg

index 5eb9318..1927fa9 100644
@@ -2134,7 +2134,7 @@ static int __init musb_probe(struct platform_device *pdev)
 	if (!iomem || irq == 0)
 		return -ENODEV;
 
-	base = ioremap(iomem->start, iomem->end - iomem->start + 1);
+	base = ioremap(iomem->start, resource_size(iomem));
 	if (!base) {
 		dev_err(dev, "ioremap failed\n");
 		return -ENOMEM;

index 1927fa9..91c31f2 100644
@@ -1696,7 +1696,7 @@ musb_vbus_store(struct device *dev, struct device_attribute *attr,
 	unsigned long	val;
 
 	if (sscanf(buf, "%lu", &val) < 1) {
-		printk(KERN_ERR "Invalid VBUS timeout ms value\n");
+		dev_err(dev, "Invalid VBUS timeout ms value\n");
 		return -EINVAL;
 	}
 

@@ -1746,7 +1746,7 @@ musb_srp_store(struct device *dev, struct device_attribute *attr,
 
 	if (sscanf(buf, "%hu", &srp) != 1
 			|| (srp != 1)) {
-		printk(KERN_ERR "SRP: Value must be 1\n");
+		dev_err(dev, "SRP: Value must be 1\n");
 		return -EINVAL;
 	}
 

index 91c31f2..52295bc 100644
@@ -1759,6 +1759,19 @@ static DEVICE_ATTR(srp, 0644, NULL, musb_srp_store);
 
 #endif /* CONFIG_USB_GADGET_MUSB_HDRC */
 
+static struct attribute *musb_attributes[] = {
+	&dev_attr_mode.attr,
+	&dev_attr_vbus.attr,
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
+	&dev_attr_srp.attr,
+#endif
+	NULL
+};
+
+static const struct attribute_group musb_attr_group = {
+	.attrs = musb_attributes,
+};
+
 #endif	/* sysfs */
 
 /* Only used to provide driver mode change events */

@@ -1833,11 +1846,7 @@ static void musb_free(struct musb *musb)
 	 */
 
 #ifdef CONFIG_SYSFS
-	device_remove_file(musb->controller, &dev_attr_mode);
-	device_remove_file(musb->controller, &dev_attr_vbus);
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
-	device_remove_file(musb->controller, &dev_attr_srp);
-#endif
+	sysfs_remove_group(&musb->controller->kobj, &musb_attr_group);
 #endif
 
 #ifdef CONFIG_USB_GADGET_MUSB_HDRC

@@ -2079,12 +2088,7 @@ bad_config:
 	}
 
 #ifdef CONFIG_SYSFS
-	status = device_create_file(dev, &dev_attr_mode);
-	status = device_create_file(dev, &dev_attr_vbus);
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
-	status = device_create_file(dev, &dev_attr_srp);
-#endif /* CONFIG_USB_GADGET_MUSB_HDRC */
-	status = 0;
+	status = sysfs_create_group(&musb->controller->kobj, &musb_attr_group);
 #endif
 	if (status)
 		goto fail2;

@@ -2092,13 +2096,6 @@ bad_config:
 	return 0;
 
 fail2:
-#ifdef CONFIG_SYSFS
-	device_remove_file(musb->controller, &dev_attr_mode);
-	device_remove_file(musb->controller, &dev_attr_vbus);
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
-	device_remove_file(musb->controller, &dev_attr_srp);
-#endif
-#endif
 	musb_platform_exit(musb);
 fail:
 	dev_err(musb->controller,

index 52295bc..b7e2d1b 100644
@@ -1314,9 +1314,6 @@ enum { MUSB_CONTROLLER_MHDRC, MUSB_CONTROLLER_HDRC, };
  */
 static int __init musb_core_init(u16 musb_type, struct musb *musb)
 {
-#ifdef MUSB_AHB_ID
-	u32 data;
-#endif
 	u8 reg;
 	char *type;
 	char aInfo[90], aRevision[32], aDate[12];

@@ -1332,19 +1329,11 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb)
 		strcat(aInfo, ", dyn FIFOs");
 	if (reg & MUSB_CONFIGDATA_MPRXE) {
 		strcat(aInfo, ", bulk combine");
-#ifdef C_MP_RX
 		musb->bulk_combine = true;
-#else
-		strcat(aInfo, " (X)");		/* no driver support */
-#endif
 	}
 	if (reg & MUSB_CONFIGDATA_MPTXE) {
 		strcat(aInfo, ", bulk split");
-#ifdef C_MP_TX
 		musb->bulk_split = true;
-#else
-		strcat(aInfo, " (X)");		/* no driver support */
-#endif
 	}
 	if (reg & MUSB_CONFIGDATA_HBRXE) {
 		strcat(aInfo, ", HB-ISO Rx");

@@ -1360,20 +1349,7 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb)
 	printk(KERN_DEBUG "%s: ConfigData=0x%02x (%s)\n",
 			musb_driver_name, reg, aInfo);
 
-#ifdef MUSB_AHB_ID
-	data = musb_readl(mbase, 0x404);
-	sprintf(aDate, "%04d-%02x-%02x", (data & 0xffff),
-		(data >> 16) & 0xff, (data >> 24) & 0xff);
-	/* FIXME ID2 and ID3 are unused */
-	data = musb_readl(mbase, 0x408);
-	printk(KERN_DEBUG "ID2=%lx\n", (long unsigned)data);
-	data = musb_readl(mbase, 0x40c);
-	printk(KERN_DEBUG "ID3=%lx\n", (long unsigned)data);
-	reg = musb_readb(mbase, 0x400);
-	musb_type = ('M' == reg) ? MUSB_CONTROLLER_MHDRC : MUSB_CONTROLLER_HDRC;
-#else
 	aDate[0] = 0;
-#endif
 	if (MUSB_CONTROLLER_MHDRC == musb_type) {
 		musb->is_multipoint = 1;
 		type = "M";

index 03d5090..2ac0e6f 100644
@@ -412,21 +412,13 @@ struct musb {
 	unsigned		hb_iso_rx:1;	/* high bandwidth iso rx? */
 	unsigned		hb_iso_tx:1;	/* high bandwidth iso tx? */
 
-#ifdef C_MP_TX
-	unsigned bulk_split:1;
+	unsigned		bulk_split:1;
 #define	can_bulk_split(musb,type) \
-		(((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_split)
-#else
-#define	can_bulk_split(musb, type)	0
-#endif
+	(((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_split)
 
-#ifdef C_MP_RX
-	unsigned bulk_combine:1;
+	unsigned		bulk_combine:1;
 #define	can_bulk_combine(musb,type) \
-		(((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_combine)
-#else
-#define	can_bulk_combine(musb, type)	0
-#endif
+	(((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_combine)
 
 #ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	/* is_suspended means USB B_PERIPHERAL suspend */

index b7e2d1b..c489326 100644
@@ -1095,6 +1095,36 @@ static struct fifo_cfg __initdata mode_4_cfg[] = {
 { .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, },
 };
 
+/* mode 5 - fits in 8KB */
+static struct fifo_cfg __initdata mode_5_cfg[] = {
+{ .hw_ep_num =  1, .style = FIFO_TX,   .maxpacket = 512, },
+{ .hw_ep_num =  1, .style = FIFO_RX,   .maxpacket = 512, },
+{ .hw_ep_num =  2, .style = FIFO_TX,   .maxpacket = 512, },
+{ .hw_ep_num =  2, .style = FIFO_RX,   .maxpacket = 512, },
+{ .hw_ep_num =  3, .style = FIFO_TX,   .maxpacket = 512, },
+{ .hw_ep_num =  3, .style = FIFO_RX,   .maxpacket = 512, },
+{ .hw_ep_num =  4, .style = FIFO_TX,   .maxpacket = 512, },
+{ .hw_ep_num =  4, .style = FIFO_RX,   .maxpacket = 512, },
+{ .hw_ep_num =  5, .style = FIFO_TX,   .maxpacket = 512, },
+{ .hw_ep_num =  5, .style = FIFO_RX,   .maxpacket = 512, },
+{ .hw_ep_num =  6, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num =  6, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num =  7, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num =  7, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num =  8, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num =  8, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num =  9, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num =  9, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num = 10, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num = 10, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num = 11, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num = 11, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num = 12, .style = FIFO_TX,   .maxpacket = 32, },
+{ .hw_ep_num = 12, .style = FIFO_RX,   .maxpacket = 32, },
+{ .hw_ep_num = 13, .style = FIFO_RXTX, .maxpacket = 512, },
+{ .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, },
+{ .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, },
+};
 
 /*
  * configure a fifo; for non-shared endpoints, this may be called

@@ -1210,6 +1240,10 @@ static int __init ep_config_from_table(struct musb *musb)
 		cfg = mode_4_cfg;
 		n = ARRAY_SIZE(mode_4_cfg);
 		break;
+	case 5:
+		cfg = mode_5_cfg;
+		n = ARRAY_SIZE(mode_5_cfg);
+		break;
 	}
 
 	printk(KERN_DEBUG "%s: setup fifo_mode %d\n",

index 1299d92..613f95a 100644
@@ -55,6 +55,10 @@
 		    MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_ADDRESS), \
 		    addr)
 
+#define musb_read_hsdma_count(mbase, bchannel)	\
+	musb_readl(mbase,	\
+		   MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_COUNT))
+
 #define musb_write_hsdma_count(mbase, bchannel, len) \
 	musb_writel(mbase, \
 		    MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_COUNT), \

@@ -96,6 +100,19 @@ static inline void musb_write_hsdma_addr(void __iomem *mbase,
 		((u16)(((u32) dma_addr >> 16) & 0xFFFF)));
 }
 
+static inline u32 musb_read_hsdma_count(void __iomem *mbase, u8 bchannel)
+{
+	u32 count = musb_readw(mbase,
+		MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_COUNT_HIGH));
+
+	count = count << 16;
+
+	count |= musb_readw(mbase,
+		MUSB_HSDMA_CHANNEL_OFFSET(bchannel, MUSB_HSDMA_COUNT_LOW));
+
+	return count;
+}
+
 static inline void musb_write_hsdma_count(void __iomem *mbase,
 				u8 bchannel, u32 len)
 {

index a237550..2fa7d5c 100644
@@ -250,20 +250,39 @@ static irqreturn_t dma_controller_irq(int irq, void *private_data)
 	u8 bchannel;
 	u8 int_hsdma;
 
-	u32 addr;
+	u32 addr, count;
 	u16 csr;
 
 	spin_lock_irqsave(&musb->lock, flags);
 
 	int_hsdma = musb_readb(mbase, MUSB_HSDMA_INTR);
-	if (!int_hsdma)
-		goto done;
 
 #ifdef CONFIG_BLACKFIN
 	/* Clear DMA interrupt flags */
 	musb_writeb(mbase, MUSB_HSDMA_INTR, int_hsdma);
 #endif
 
+	if (!int_hsdma) {
+		DBG(2, "spurious DMA irq\n");
+
+		for (bchannel = 0; bchannel < MUSB_HSDMA_CHANNELS; bchannel++) {
+			musb_channel = (struct musb_dma_channel *)
+					&(controller->channel[bchannel]);
+			channel = &musb_channel->channel;
+			if (channel->status == MUSB_DMA_STATUS_BUSY) {
+				count = musb_read_hsdma_count(mbase, bchannel);
+
+				if (count == 0)
+					int_hsdma |= (1 << bchannel);
+			}
+		}
+
+		DBG(2, "int_hsdma = 0x%x\n", int_hsdma);
+
+		if (!int_hsdma)
+			goto done;
+	}
+
 	for (bchannel = 0; bchannel < MUSB_HSDMA_CHANNELS; bchannel++) {
 		if (int_hsdma & (1 << bchannel)) {
 			musb_channel = (struct musb_dma_channel *)

index 74c4c36..c3fdd6d 100644
@@ -1771,6 +1771,9 @@ static int musb_schedule(
 	int			best_end, epnum;
 	struct musb_hw_ep	*hw_ep = NULL;
 	struct list_head	*head = NULL;
+	u8			toggle;
+	u8			txtype;
+	struct urb		*urb = next_urb(qh);
 
 	/* use fixed hardware for control and bulk */
 	if (qh->type == USB_ENDPOINT_XFER_CONTROL) {

@@ -1809,6 +1812,27 @@ static int musb_schedule(
 		diff -= (qh->maxpacket * qh->hb_mult);
 
 		if (diff >= 0 && best_diff > diff) {
+
+			/*
+			 * Mentor controller has a bug in that if we schedule
+			 * a BULK Tx transfer on an endpoint that had earlier
+			 * handled ISOC then the BULK transfer has to start on
+			 * a zero toggle.  If the BULK transfer starts on a 1
+			 * toggle then this transfer will fail as the mentor
+			 * controller starts the Bulk transfer on a 0 toggle
+			 * irrespective of the programming of the toggle bits
+			 * in the TXCSR register.  Check for this condition
+			 * while allocating the EP for a Tx Bulk transfer.  If
+			 * so skip this EP.
+			 */
+			hw_ep = musb->endpoints + epnum;
+			toggle = usb_gettoggle(urb->dev, qh->epnum, !is_in);
+			txtype = (musb_readb(hw_ep->regs, MUSB_TXTYPE)
+					>> 4) & 0x3;
+			if (!is_in && (qh->type == USB_ENDPOINT_XFER_BULK) &&
+				toggle && (txtype == USB_ENDPOINT_XFER_ISOC))
+				continue;
+
 			best_diff = diff;
 			best_end = epnum;
 		}

index a44a450..3c69a76 100644
@@ -1191,8 +1191,13 @@ irqreturn_t cppi_interrupt(int irq, void *dev_id)
 
 		bd = tx_ch->head;
 
+		/*
+		 * If Head is null then this could mean that a abort interrupt
+		 * that needs to be acknowledged.
+		 */
 		if (NULL == bd) {
 			DBG(1, "null BD\n");
+			tx_ram->tx_complete = 0;
 			continue;
 		}
 

@@ -1412,15 +1417,6 @@ static int cppi_channel_abort(struct dma_channel *channel)
 
 	if (cppi_ch->transmit) {
 		struct cppi_tx_stateram __iomem *tx_ram;
-		int			enabled;
-
-		/* mask interrupts raised to signal teardown complete.  */
-		enabled = musb_readl(tibase, DAVINCI_TXCPPI_INTENAB_REG)
-				& (1 << cppi_ch->index);
-		if (enabled)
-			musb_writel(tibase, DAVINCI_TXCPPI_INTCLR_REG,
-					(1 << cppi_ch->index));
-
 		/* REVISIT put timeouts on these controller handshakes */
 
 		cppi_dump_tx(6, cppi_ch, " (teardown)");

@@ -1435,7 +1431,6 @@ static int cppi_channel_abort(struct dma_channel *channel)
 		do {
 			value = musb_readl(&tx_ram->tx_complete, 0);
 		} while (0xFFFFFFFC != value);
-		musb_writel(&tx_ram->tx_complete, 0, 0xFFFFFFFC);
 
 		/* FIXME clean up the transfer state ... here?
 		 * the completion routine should get called with

@@ -1448,23 +1443,15 @@ static int cppi_channel_abort(struct dma_channel *channel)
 		musb_writew(regs, MUSB_TXCSR, value);
 		musb_writew(regs, MUSB_TXCSR, value);
 
-		/* While we scrub the TX state RAM, ensure that we clean
-		 * up any interrupt that's currently asserted:
+		/*
 		 * 1. Write to completion Ptr value 0x1(bit 0 set)
 		 *    (write back mode)
-		 * 2. Write to completion Ptr value 0x0(bit 0 cleared)
-		 *    (compare mode)
-		 * Value written is compared(for bits 31:2) and when
-		 * equal, interrupt is deasserted.
+		 * 2. Wait for abort interrupt and then put the channel in
+		 *    compare mode by writing 1 to the tx_complete register.
 		 */
 		cppi_reset_tx(tx_ram, 1);
-		musb_writel(&tx_ram->tx_complete, 0, 0);
-
-		/* re-enable interrupt */
-		if (enabled)
-			musb_writel(tibase, DAVINCI_TXCPPI_INTENAB_REG,
-					(1 << cppi_ch->index));
-
+		cppi_ch->head = 0;
+		musb_writel(&tx_ram->tx_complete, 0, 1);
 		cppi_dump_tx(5, cppi_ch, " (done teardown)");
 
 		/* REVISIT tx side _should_ clean up the same way

index ad26e65..bcee133 100644
@@ -30,7 +30,6 @@ void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
 	void __iomem *fifo = hw_ep->fifo;
 	void __iomem *epio = hw_ep->regs;
 	u8 epnum = hw_ep->epnum;
-	u16 dma_reg = 0;
 
 	prefetch((u8 *)src);
 

@@ -42,15 +41,17 @@ void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
 	dump_fifo_data(src, len);
 
 	if (!ANOMALY_05000380 && epnum != 0) {
-		flush_dcache_range((unsigned int)src,
-			(unsigned int)(src + len));
+		u16 dma_reg;
+
+		flush_dcache_range((unsigned long)src,
+			(unsigned long)(src + len));
 
 		/* Setup DMA address register */
-		dma_reg = (u16) ((u32) src & 0xFFFF);
+		dma_reg = (u32)src;
 		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
 		SSYNC();
 
-		dma_reg = (u16) (((u32) src >> 16) & 0xFFFF);
+		dma_reg = (u32)src >> 16;
 		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
 		SSYNC();
 

@@ -79,12 +80,9 @@ void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
 		SSYNC();
 
 		if (unlikely((unsigned long)src & 0x01))
-			outsw_8((unsigned long)fifo, src,
-				len & 0x01 ? (len >> 1) + 1 : len >> 1);
+			outsw_8((unsigned long)fifo, src, (len + 1) >> 1);
 		else
-			outsw((unsigned long)fifo, src,
-				len & 0x01 ? (len >> 1) + 1 : len >> 1);
-
+			outsw((unsigned long)fifo, src, (len + 1) >> 1);
 	}
 }
 /*

@@ -94,19 +92,19 @@ void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
 {
 	void __iomem *fifo = hw_ep->fifo;
 	u8 epnum = hw_ep->epnum;
-	u16 dma_reg = 0;
 
 	if (ANOMALY_05000467 && epnum != 0) {
+		u16 dma_reg;
 
-		invalidate_dcache_range((unsigned int)dst,
-			(unsigned int)(dst + len));
+		invalidate_dcache_range((unsigned long)dst,
+			(unsigned long)(dst + len));
 
 		/* Setup DMA address register */
-		dma_reg = (u16) ((u32) dst & 0xFFFF);
+		dma_reg = (u32)dst;
 		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
 		SSYNC();
 
-		dma_reg = (u16) (((u32) dst >> 16) & 0xFFFF);
+		dma_reg = (u32)dst >> 16;
 		bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
 		SSYNC();
 

index c489326..bd14e81 100644
@@ -557,6 +557,69 @@ static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
 		handled = IRQ_HANDLED;
 	}
 
+
+	if (int_usb & MUSB_INTR_SUSPEND) {
+		DBG(1, "SUSPEND (%s) devctl %02x power %02x\n",
+				otg_state_string(musb), devctl, power);
+		handled = IRQ_HANDLED;
+
+		switch (musb->xceiv->state) {
+#ifdef	CONFIG_USB_MUSB_OTG
+		case OTG_STATE_A_PERIPHERAL:
+			/* We also come here if the cable is removed, since
+			 * this silicon doesn't report ID-no-longer-grounded.
+			 *
+			 * We depend on T(a_wait_bcon) to shut us down, and
+			 * hope users don't do anything dicey during this
+			 * undesired detour through A_WAIT_BCON.
+			 */
+			musb_hnp_stop(musb);
+			usb_hcd_resume_root_hub(musb_to_hcd(musb));
+			musb_root_disconnect(musb);
+			musb_platform_try_idle(musb, jiffies
+					+ msecs_to_jiffies(musb->a_wait_bcon
+						? : OTG_TIME_A_WAIT_BCON));
+
+			break;
+#endif
+		case OTG_STATE_B_IDLE:
+			if (!musb->is_active)
+				break;
+		case OTG_STATE_B_PERIPHERAL:
+			musb_g_suspend(musb);
+			musb->is_active = is_otg_enabled(musb)
+					&& musb->xceiv->gadget->b_hnp_enable;
+			if (musb->is_active) {
+#ifdef	CONFIG_USB_MUSB_OTG
+				musb->xceiv->state = OTG_STATE_B_WAIT_ACON;
+				DBG(1, "HNP: Setting timer for b_ase0_brst\n");
+				mod_timer(&musb->otg_timer, jiffies
+					+ msecs_to_jiffies(
+							OTG_TIME_B_ASE0_BRST));
+#endif
+			}
+			break;
+		case OTG_STATE_A_WAIT_BCON:
+			if (musb->a_wait_bcon != 0)
+				musb_platform_try_idle(musb, jiffies
+					+ msecs_to_jiffies(musb->a_wait_bcon));
+			break;
+		case OTG_STATE_A_HOST:
+			musb->xceiv->state = OTG_STATE_A_SUSPEND;
+			musb->is_active = is_otg_enabled(musb)
+					&& musb->xceiv->host->b_hnp_enable;
+			break;
+		case OTG_STATE_B_HOST:
+			/* Transition to B_PERIPHERAL, see 6.8.2.6 p 44 */
+			DBG(1, "REVISIT: SUSPEND as B_HOST\n");
+			break;
+		default:
+			/* "should not happen" */
+			musb->is_active = 0;
+			break;
+		}
+	}
+
 	if (int_usb & MUSB_INTR_CONNECT) {
 		struct usb_hcd *hcd = musb_to_hcd(musb);
 

@@ -625,10 +688,61 @@ b_host:
 	}
 #endif	/* CONFIG_USB_MUSB_HDRC_HCD */
 
+	if ((int_usb & MUSB_INTR_DISCONNECT) && !musb->ignore_disconnect) {
+		DBG(1, "DISCONNECT (%s) as %s, devctl %02x\n",
+				otg_state_string(musb),
+				MUSB_MODE(musb), devctl);
+		handled = IRQ_HANDLED;
+
+		switch (musb->xceiv->state) {
+#ifdef CONFIG_USB_MUSB_HDRC_HCD
+		case OTG_STATE_A_HOST:
+		case OTG_STATE_A_SUSPEND:
+			usb_hcd_resume_root_hub(musb_to_hcd(musb));
+			musb_root_disconnect(musb);
+			if (musb->a_wait_bcon != 0 && is_otg_enabled(musb))
+				musb_platform_try_idle(musb, jiffies
+					+ msecs_to_jiffies(musb->a_wait_bcon));
+			break;
+#endif	/* HOST */
+#ifdef CONFIG_USB_MUSB_OTG
+		case OTG_STATE_B_HOST:
+			/* REVISIT this behaves for "real disconnect"
+			 * cases; make sure the other transitions from
+			 * from B_HOST act right too.  The B_HOST code
+			 * in hnp_stop() is currently not used...
+			 */
+			musb_root_disconnect(musb);
+			musb_to_hcd(musb)->self.is_b_host = 0;
+			musb->xceiv->state = OTG_STATE_B_PERIPHERAL;
+			MUSB_DEV_MODE(musb);
+			musb_g_disconnect(musb);
+			break;
+		case OTG_STATE_A_PERIPHERAL:
+			musb_hnp_stop(musb);
+			musb_root_disconnect(musb);
+			/* FALLTHROUGH */
+		case OTG_STATE_B_WAIT_ACON:
+			/* FALLTHROUGH */
+#endif	/* OTG */
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
+		case OTG_STATE_B_PERIPHERAL:
+		case OTG_STATE_B_IDLE:
+			musb_g_disconnect(musb);
+			break;
+#endif	/* GADGET */
+		default:
+			WARNING("unhandled DISCONNECT transition (%s)\n",
+				otg_state_string(musb));
+			break;
+		}
+	}
+
 	/* mentor saves a bit: bus reset and babble share the same irq.
 	 * only host sees babble; only peripheral sees bus reset.
 	 */
 	if (int_usb & MUSB_INTR_RESET) {
+		handled = IRQ_HANDLED;
 		if (is_host_capable() && (devctl & MUSB_DEVCTL_HM) != 0) {
 			/*
 			 * Looks like non-HS BABBLE can be ignored, but

@@ -641,7 +755,7 @@ b_host:
 				DBG(1, "BABBLE devctl: %02x\n", devctl);
 			else {
 				ERR("Stopping host session -- babble\n");
-				musb_writeb(mbase, MUSB_DEVCTL, 0);
+				musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
 			}
 		} else if (is_peripheral_capable()) {
 			DBG(1, "BUS RESET as %s\n", otg_state_string(musb));

@@ -686,29 +800,7 @@ b_host:
 					otg_state_string(musb));
 			}
 		}
-
-		handled = IRQ_HANDLED;
 	}
-	schedule_work(&musb->irq_work);
-
-	return handled;
-}
-
-/*
- * Interrupt Service Routine to record USB "global" interrupts.
- * Since these do not happen often and signify things of
- * paramount importance, it seems OK to check them individually;
- * the order of the tests is specified in the manual
- *
- * @param musb instance pointer
- * @param int_usb register contents
- * @param devctl
- * @param power
- */
-static irqreturn_t musb_stage2_irq(struct musb *musb, u8 int_usb,
-				u8 devctl, u8 power)
-{
-	irqreturn_t handled = IRQ_NONE;
 
 #if 0
 /* REVISIT ... this would be for multiplexing periodic endpoints, or

@@ -755,117 +847,7 @@ static irqreturn_t musb_stage2_irq(struct musb *musb, u8 int_usb,
 	}
 #endif
 
-	if ((int_usb & MUSB_INTR_DISCONNECT) && !musb->ignore_disconnect) {
-		DBG(1, "DISCONNECT (%s) as %s, devctl %02x\n",
-				otg_state_string(musb),
-				MUSB_MODE(musb), devctl);
-		handled = IRQ_HANDLED;
-
-		switch (musb->xceiv->state) {
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
-		case OTG_STATE_A_HOST:
-		case OTG_STATE_A_SUSPEND:
-			usb_hcd_resume_root_hub(musb_to_hcd(musb));
-			musb_root_disconnect(musb);
-			if (musb->a_wait_bcon != 0 && is_otg_enabled(musb))
-				musb_platform_try_idle(musb, jiffies
-					+ msecs_to_jiffies(musb->a_wait_bcon));
-			break;
-#endif	/* HOST */
-#ifdef CONFIG_USB_MUSB_OTG
-		case OTG_STATE_B_HOST:
-			/* REVISIT this behaves for "real disconnect"
-			 * cases; make sure the other transitions from
-			 * from B_HOST act right too.  The B_HOST code
-			 * in hnp_stop() is currently not used...
-			 */
-			musb_root_disconnect(musb);
-			musb_to_hcd(musb)->self.is_b_host = 0;
-			musb->xceiv->state = OTG_STATE_B_PERIPHERAL;
-			MUSB_DEV_MODE(musb);
-			musb_g_disconnect(musb);
-			break;
-		case OTG_STATE_A_PERIPHERAL:
-			musb_hnp_stop(musb);
-			musb_root_disconnect(musb);
-			/* FALLTHROUGH */
-		case OTG_STATE_B_WAIT_ACON:
-			/* FALLTHROUGH */
-#endif	/* OTG */
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
-		case OTG_STATE_B_PERIPHERAL:
-		case OTG_STATE_B_IDLE:
-			musb_g_disconnect(musb);
-			break;
-#endif	/* GADGET */
-		default:
-			WARNING("unhandled DISCONNECT transition (%s)\n",
-				otg_state_string(musb));
-			break;
-		}
-
-		schedule_work(&musb->irq_work);
-	}
-
-	if (int_usb & MUSB_INTR_SUSPEND) {
-		DBG(1, "SUSPEND (%s) devctl %02x power %02x\n",
-				otg_state_string(musb), devctl, power);
-		handled = IRQ_HANDLED;
-
-		switch (musb->xceiv->state) {
-#ifdef	CONFIG_USB_MUSB_OTG
-		case OTG_STATE_A_PERIPHERAL:
-			/* We also come here if the cable is removed, since
-			 * this silicon doesn't report ID-no-longer-grounded.
-			 *
-			 * We depend on T(a_wait_bcon) to shut us down, and
-			 * hope users don't do anything dicey during this
-			 * undesired detour through A_WAIT_BCON.
-			 */
-			musb_hnp_stop(musb);
-			usb_hcd_resume_root_hub(musb_to_hcd(musb));
-			musb_root_disconnect(musb);
-			musb_platform_try_idle(musb, jiffies
-					+ msecs_to_jiffies(musb->a_wait_bcon
-						? : OTG_TIME_A_WAIT_BCON));
-			break;
-#endif
-		case OTG_STATE_B_PERIPHERAL:
-			musb_g_suspend(musb);
-			musb->is_active = is_otg_enabled(musb)
-					&& musb->xceiv->gadget->b_hnp_enable;
-			if (musb->is_active) {
-#ifdef	CONFIG_USB_MUSB_OTG
-				musb->xceiv->state = OTG_STATE_B_WAIT_ACON;
-				DBG(1, "HNP: Setting timer for b_ase0_brst\n");
-				mod_timer(&musb->otg_timer, jiffies
-					+ msecs_to_jiffies(
-							OTG_TIME_B_ASE0_BRST));
-#endif
-			}
-			break;
-		case OTG_STATE_A_WAIT_BCON:
-			if (musb->a_wait_bcon != 0)
-				musb_platform_try_idle(musb, jiffies
-					+ msecs_to_jiffies(musb->a_wait_bcon));
-			break;
-		case OTG_STATE_A_HOST:
-			musb->xceiv->state = OTG_STATE_A_SUSPEND;
-			musb->is_active = is_otg_enabled(musb)
-					&& musb->xceiv->host->b_hnp_enable;
-			break;
-		case OTG_STATE_B_HOST:
-			/* Transition to B_PERIPHERAL, see 6.8.2.6 p 44 */
-			DBG(1, "REVISIT: SUSPEND as B_HOST\n");
-			break;
-		default:
-			/* "should not happen" */
-			musb->is_active = 0;
-			break;
-		}
-		schedule_work(&musb->irq_work);
-	}
-
+	schedule_work(&musb->irq_work);
 
 	return handled;
 }

@@ -1597,11 +1579,6 @@ irqreturn_t musb_interrupt(struct musb *musb)
 		ep_num++;
 	}
 
-	/* finish handling "global" interrupts after handling fifos */
-	if (musb->int_usb)
-		retval |= musb_stage2_irq(musb,
-				musb->int_usb, devctl, power);
-
 	return retval;
 }
 

index bd14e81..4c8962f 100644
@@ -1341,8 +1341,10 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb)
 	reg = musb_read_configdata(mbase);
 
 	strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8");
-	if (reg & MUSB_CONFIGDATA_DYNFIFO)
+	if (reg & MUSB_CONFIGDATA_DYNFIFO) {
 		strcat(aInfo, ", dyn FIFOs");
+		musb->dyn_fifo = true;
+	}
 	if (reg & MUSB_CONFIGDATA_MPRXE) {
 		strcat(aInfo, ", bulk combine");
 		musb->bulk_combine = true;

index 2ac0e6f..eaa0114 100644
@@ -411,6 +411,7 @@ struct musb {
 
 	unsigned		hb_iso_rx:1;	/* high bandwidth iso rx? */
 	unsigned		hb_iso_tx:1;	/* high bandwidth iso tx? */
+	unsigned		dyn_fifo:1;	/* dynamic FIFO supported? */
 
 	unsigned		bulk_split:1;
 #define	can_bulk_split(musb,type) \

index 4c8962f..074d380 100644
@@ -2031,6 +2031,7 @@ bad_config:
 	/* host side needs more setup */
 	if (is_host_enabled(musb)) {
 		struct usb_hcd	*hcd = musb_to_hcd(musb);
+		u8 busctl;
 
 		otg_set_host(musb->xceiv, &hcd->self);
 

@@ -2038,6 +2039,13 @@ bad_config:
 			hcd->self.otg_port = 1;
 		musb->xceiv->host = &hcd->self;
 		hcd->power_budget = 2 * (plat->power ? : 250);
+
+		/* program PHY to use external vBus if required */
+		if (plat->extvbus) {
+			busctl = musb_readb(musb->mregs, MUSB_ULPI_BUSCONTROL);
+			busctl |= MUSB_ULPI_USE_EXTVBUS;
+			musb_writeb(musb->mregs, MUSB_ULPI_BUSCONTROL, busctl);
+		}
 	}
 
 	/* For the host-only role, we can activate right away.

index 473a94e..9a8621a 100644
@@ -72,6 +72,10 @@
 #define MUSB_DEVCTL_HR		0x02
 #define MUSB_DEVCTL_SESSION	0x01
 
+/* MUSB ULPI VBUSCONTROL */
+#define MUSB_ULPI_USE_EXTVBUS	0x01
+#define MUSB_ULPI_USE_EXTVBUSIND 0x02
+
 /* TESTMODE */
 #define MUSB_TEST_FORCE_HOST	0x80
 #define MUSB_TEST_FIFO_ACCESS	0x40

@@ -246,6 +250,7 @@
 
 /* REVISIT: vctrl/vstatus: optional vendor utmi+phy register at 0x68 */
 #define MUSB_HWVERS		0x6C	/* 8 bit */
+#define MUSB_ULPI_BUSCONTROL	0x70	/* 8 bit */
 
 #define MUSB_EPINFO		0x78	/* 8 bit */
 #define MUSB_RAMINFO		0x79	/* 8 bit */

index d437556..4b7f8fa 100644
@@ -76,6 +76,9 @@ struct musb_hdrc_platform_data {
 	/* (HOST or OTG) msec/2 after VBUS on till power good */
 	u8		potpgt;
 
+	/* (HOST or OTG) program PHY for external Vbus */
+	unsigned	extvbus:1;
+
 	/* Power the device on or off */
 	int		(*set_power)(int state);
 

index 74d07f4..2460f0d 100644
@@ -681,6 +681,7 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev)
 	iounmap(omap->tll_base);
 	iounmap(omap->uhh_base);
 	usb_put_hcd(hcd);
+	kfree(omap);
 
 	return 0;
 }

index 2460f0d..17e4ceb 100644
@@ -37,6 +37,7 @@
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/gpio.h>
+#include <linux/regulator/consumer.h>
 #include <plat/usb.h>
 
 /*

@@ -178,6 +179,11 @@ struct ehci_hcd_omap {
 	void __iomem		*uhh_base;
 	void __iomem		*tll_base;
 	void __iomem		*ehci_base;
+
+	/* Regulators for USB PHYs.
+	 * Each PHY can have a seperate regulator.
+	 */
+	struct regulator        *regulator[OMAP3_HS_USB_PORTS];
 };
 
 /*-------------------------------------------------------------------------*/

@@ -546,6 +552,8 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 
 	int irq = platform_get_irq(pdev, 0);
 	int ret = -ENODEV;
+	int i;
+	char supply[7];
 
 	if (!pdata) {
 		dev_dbg(&pdev->dev, "missing platform_data\n");

@@ -613,6 +621,21 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 		goto err_tll_ioremap;
 	}
 
+	/* get ehci regulator and enable */
+	for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
+		if (omap->port_mode[i] != EHCI_HCD_OMAP_MODE_PHY) {
+			omap->regulator[i] = NULL;
+			continue;
+		}
+		snprintf(supply, sizeof(supply), "hsusb%d", i);
+		omap->regulator[i] = regulator_get(omap->dev, supply);
+		if (IS_ERR(omap->regulator[i]))
+			dev_dbg(&pdev->dev,
+			"failed to get ehci port%d regulator\n", i);
+		else
+			regulator_enable(omap->regulator[i]);
+	}
+
 	ret = omap_start_ehc(omap, hcd);
 	if (ret) {
 		dev_dbg(&pdev->dev, "failed to start ehci\n");

@@ -641,6 +664,12 @@ err_add_hcd:
 	omap_stop_ehc(omap, hcd);
 
 err_start:
+	for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
+		if (omap->regulator[i]) {
+			regulator_disable(omap->regulator[i]);
+			regulator_put(omap->regulator[i]);
+		}
+	}
 	iounmap(omap->tll_base);
 
 err_tll_ioremap:

@@ -674,10 +703,17 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev)
 {
 	struct ehci_hcd_omap *omap = platform_get_drvdata(pdev);
 	struct usb_hcd *hcd = ehci_to_hcd(omap->ehci);
+	int i;
 
 	usb_remove_hcd(hcd);
 	omap_stop_ehc(omap, hcd);
 	iounmap(hcd->regs);
+	for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
+		if (omap->regulator[i]) {
+			regulator_disable(omap->regulator[i]);
+			regulator_put(omap->regulator[i]);
+		}
+	}
 	iounmap(omap->tll_base);
 	iounmap(omap->uhh_base);
 	usb_put_hcd(hcd);

index e13c770..1c86809 100644
@@ -648,7 +648,7 @@ void dma_controller_destroy(struct dma_controller *c)
 		}
 	}
 
-	if (!tusb_dma->multichannel && tusb_dma && tusb_dma->ch >= 0)
+	if (tusb_dma && !tusb_dma->multichannel && tusb_dma->ch >= 0)
 		omap_free_dma(tusb_dma->ch);
 
 	kfree(tusb_dma);