ipath - driver submission for 2.6.17
PATCH 1/1 ipath - driver submission for 2.6.17
This is a submission of the ipath driver for inclusion in 2.6.17. Roland, if this looks good to you, please apply.
Changes since the last round of review comments from Roland:
- Support for PathScale userland SMA dropped
- Passes sparse with CF=-D__CHECK_ENDIAN__
- Builds cleanly on ia64
- A few other little fixes here and there
If you have any comments or suggestions, please let me know.
The ipath driver is a driver for PathScale InfiniPath host channel adapters (HCAs) based on the HT-400 and PE-800 chips, including the InfiniPath HT-460, the small form factor InfiniPath HT-460, the InfiniPath HT-470 and the Linux Networx LS/X.
The core driver manages the hardware, and provides a fast memory-mapped interface to the hardware for userspace networking applications. Our implementation of the Infiniband protocols and integration into the kernel's Infiniband stack is written as a layer on top of the core driver.
PATCH 1/1 ipath - core device driver
The ipath driver is a low-level driver for PathScale InfiniPath host channel adapters (HCAs) based on the HT-400 and PE-800 chips, including the InfiniPath HT-460, the small form factor InfiniPath HT-460, the InfiniPath HT-470 and the Linux Networx LS/X.
The ipath_driver.c file contains much of the low-level device handling code.
drivers/infiniband/hw/ipath/ipath_driver.c new file +1983 -0
@@ -0,0 +1,1983 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include <linux/spinlock.h> +#include <linux/idr.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/vmalloc.h> + +#include "ipath_kernel.h" +#include "ips_common.h" +#include "ipath_layer.h" + +static void ipath_update_pio_bufs (struct ipath_devdata *); + +const char *ipath_get_unit_name (int unit) +{ +static char iname[16 ]; +snprintf (iname,sizeof iname,"infinipath%u" , unit); +return iname; +} + +EXPORT_SYMBOL_GPL (ipath_get_unit_name); + +#define DRIVER_LOAD_MSG "PathScale " IPATH_DRV_NAME " loaded: " +#define PFX IPATH_DRV_NAME ": " + +/* +* The size has to be longer than this string, so we can append +* board/chip information to it in the init code. +*/ +const char ipath_core_version[] =IPATH_IDSTR "\n" ; + +static struct idr unit_table; +DEFINE_SPINLOCK (ipath_devs_lock); +LIST_HEAD (ipath_dev_list); + +wait_queue_head_t ipath_sma_state_wait; + +unsigned ipath_debug = __IPATH_INFO; + +module_param_named (debug, ipath_debug, uint,S_IWUSR |S_IRUGO ); +MODULE_PARM_DESC (debug,"mask for debug prints" ); +EXPORT_SYMBOL_GPL (ipath_debug); + +MODULE_LICENSE ("GPL" ); +MODULE_AUTHOR ("PathScale <[email protected]>" ); +MODULE_DESCRIPTION ("Pathscale InfiniPath driver" ); + +const char *ipath_ibcstatus_str[] = { +"Disabled" , +"LinkUp" , +"PollActive" , +"PollQuiet" , +"SleepDelay" , +"SleepQuiet" , +"LState6" ,/* unused */ +"LState7" ,/* unused */ +"CfgDebounce" , +"CfgRcvfCfg" , +"CfgWaitRmt" , +"CfgIdle" , +"RecovRetrain" , +"LState0xD" ,/* unused */ +"RecovWaitRmt" , +"RecovIdle" , +}; + +/* +* These variables are initialized in the chip-specific files +* but are defined here. +*/ +u16 ipath_gpio_sda_num, ipath_gpio_scl_num; +u64 ipath_gpio_sda, ipath_gpio_scl; +u64 infinipath_i_bitsextant; +ipath_err_t infinipath_e_bitsextant, infinipath_hwe_bitsextant; +u32 infinipath_i_rcvavail_mask, infinipath_i_rcvurg_mask; + +static void __devexit ipath_remove_one(struct pci_dev *); +static int __devinit ipath_init_one (struct pci_dev *, +const struct pci_device_id *); + +/* Only needed for registration, nothing else needs this info */ +#define PCI_VENDOR_ID_PATHSCALE 0x1fc1 +#define PCI_DEVICE_ID_INFINIPATH_HT 0xd +#define PCI_DEVICE_ID_INFINIPATH_PE800 0x10 + +static const struct pci_device_id ipath_pci_tbl[] = { + {PCI_DEVICE (PCI_VENDOR_ID_PATHSCALE , +PCI_DEVICE_ID_INFINIPATH_HT )}, + {PCI_DEVICE (PCI_VENDOR_ID_PATHSCALE , +PCI_DEVICE_ID_INFINIPATH_PE800 )}, +}; + +MODULE_DEVICE_TABLE (pci, ipath_pci_tbl); + +static struct pci_driver ipath_driver = { + .name =IPATH_DRV_NAME , + .probe = ipath_init_one, + .remove =__devexit_p (ipath_remove_one), + .id_table = ipath_pci_tbl, +}; + +/* +* This is where port 0's rcvhdrtail register is written back; we also +* want nothing else sharing the cache line, so make it a cache line +* in size. Used for all units. +*/ +volatile __le64 *ipath_port0_rcvhdrtail; +dma_addr_t ipath_port0_rcvhdrtail_dma; +static int port0_rcvhdrtail_refs; + +static inline void read_bars (struct ipath_devdata *dd,struct pci_dev *dev, +u32 *bar0,u32 *bar1) +{ +int ret; + + ret =pci_read_config_dword (dev,PCI_BASE_ADDRESS_0 , bar0); +if (ret) +ipath_dev_err (dd,"failed to read bar0 before enable: " +"error %d\n" , -ret); + + ret =pci_read_config_dword (dev,PCI_BASE_ADDRESS_1 , bar1); +if (ret) +ipath_dev_err (dd,"failed to read bar1 before enable: " +"error %d\n" , -ret); + +ipath_dbg ("Read bar0 %x bar1 %x\n" , *bar0, *bar1); +} + +static void ipath_free_devdata (struct pci_dev *pdev, +struct ipath_devdata *dd) +{ +unsigned long flags; + +pci_set_drvdata (pdev,NULL ); + +if (dd->ipath_unit !=-1 ) { +spin_lock_irqsave (&ipath_devs_lock, flags); +idr_remove (&unit_table, dd->ipath_unit); +list_del (&dd->ipath_list); +spin_unlock_irqrestore (&ipath_devs_lock, flags); + } +dma_free_coherent (&pdev->dev,sizeof (*dd), dd, dd->ipath_dma_addr); +} + +static struct ipath_devdata *ipath_alloc_devdata (struct pci_dev *pdev) +{ +unsigned long flags; +struct ipath_devdata *dd; +dma_addr_t dma_addr; +int ret; + +if (!idr_pre_get (&unit_table,GFP_KERNEL )) { + dd =ERR_PTR (-ENOMEM ); + goto bail; + } + + dd =dma_alloc_coherent (&pdev->dev,sizeof (*dd), &dma_addr, +GFP_KERNEL ); + +if (!dd) { + dd =ERR_PTR (-ENOMEM ); + goto bail; + } + + dd->ipath_dma_addr = dma_addr; + dd->ipath_unit =-1 ; + +spin_lock_irqsave (&ipath_devs_lock, flags); + + ret =idr_get_new (&unit_table, dd, &dd->ipath_unit); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME + ": Could not allocate unit ID: error %d\n", -ret); +ipath_free_devdata (pdev, dd); + dd =ERR_PTR (ret); + goto bail_unlock; + } + + dd->pcidev = pdev; +pci_set_drvdata (pdev, dd); + +list_add (&dd->ipath_list, &ipath_dev_list); + +bail_unlock: +spin_unlock_irqrestore (&ipath_devs_lock, flags); + +bail: +return dd; +} + +static inline struct ipath_devdata *__ipath_lookup (int unit) +{ +return idr_find (&unit_table, unit); +} + +struct ipath_devdata *ipath_lookup (int unit) +{ +struct ipath_devdata *dd; +unsigned long flags; + +spin_lock_irqsave (&ipath_devs_lock, flags); + dd =__ipath_lookup (unit); +spin_unlock_irqrestore (&ipath_devs_lock, flags); + +return dd; +} + +int ipath_count_units (int *npresentp,int *nupp,u32 *maxportsp) +{ +int nunits, npresent, nup; +struct ipath_devdata *dd; +unsigned long flags; +u32 maxports; + + nunits = npresent = nup = maxports =0 ; + +spin_lock_irqsave (&ipath_devs_lock, flags); + +list_for_each_entry (dd, &ipath_dev_list, ipath_list) { + nunits++; +if ((dd->ipath_flags &IPATH_PRESENT ) && dd->ipath_kregbase) + npresent++; +if (dd->ipath_lid && + !(dd->ipath_flags & (IPATH_DISABLED |IPATH_LINKDOWN + |IPATH_LINKUNK ))) + nup++; +if (dd->ipath_cfgports > maxports) + maxports = dd->ipath_cfgports; + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + +if (npresentp) + *npresentp = npresent; +if (nupp) + *nupp = nup; +if (maxportsp) + *maxportsp = maxports; + +return nunits; +} + +static int init_port0_rcvhdrtail (struct pci_dev *pdev) +{ +int ret; + +mutex_lock (&ipath_mutex); + +if (!ipath_port0_rcvhdrtail) { + ipath_port0_rcvhdrtail = +dma_alloc_coherent (&pdev->dev, +IPATH_PORT0_RCVHDRTAIL_SIZE , + &ipath_port0_rcvhdrtail_dma, +GFP_KERNEL ); + +if (!ipath_port0_rcvhdrtail) { + ret = -ENOMEM ; + goto bail; + } + } + port0_rcvhdrtail_refs++; + ret =0 ; + +bail: +mutex_unlock (&ipath_mutex); + +return ret; +} + +static void cleanup_port0_rcvhdrtail (struct pci_dev *pdev) +{ +mutex_lock (&ipath_mutex); + +if (!--port0_rcvhdrtail_refs) { +dma_free_coherent (&pdev->dev,IPATH_PORT0_RCVHDRTAIL_SIZE , + (void *) ipath_port0_rcvhdrtail, + ipath_port0_rcvhdrtail_dma); + ipath_port0_rcvhdrtail =NULL ; + } + +mutex_unlock (&ipath_mutex); +} + +/* +* These next two routines are placeholders in case we don't have per-arch +* code for controlling write combining. If explicit control of write +* combining is not available, performance will probably be awful. +*/ + +int __attribute__((weak))ipath_enable_wc (struct ipath_devdata *dd) +{ +return -EOPNOTSUPP ; +} + +void __attribute__((weak))ipath_disable_wc (struct ipath_devdata *dd) +{ +} + +static int __devinit ipath_init_one (struct pci_dev *pdev, +const struct pci_device_id *ent) +{ +int ret, len, j; +struct ipath_devdata *dd; +unsigned long long addr; +u32 bar0 =0 , bar1 =0 ; +u8 rev; + + ret =init_port0_rcvhdrtail (pdev); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME +": Could not allocate port0_rcvhdrtail: error %d\n" , + -ret); + goto bail; + } + + dd =ipath_alloc_devdata (pdev); +if (IS_ERR (dd)) { + ret =PTR_ERR (dd); + printk(KERN_ERR IPATH_DRV_NAME + ": Could not allocate devdata: error %d\n", -ret); + goto bail_rcvhdrtail; + } + +ipath_cdbg (VERBOSE ,"initializing unit #%u\n" , dd->ipath_unit); + +read_bars (dd, pdev, &bar0, &bar1); + + ret =pci_enable_device (pdev); +if (ret) { +/* This can happen iff: +* +* We did a chip reset, and then failed to reprogram the +* BAR, or the chip reset due to an internal error. We then +* unloaded the driver and reloaded it. +* +* Both reset cases set the BAR back to initial state. For +* the latter case, the AER sticky error bit at offset 0x718 +* should be set, but the Linux kernel doesn't yet know +* about that, it appears. If the original BAR was retained +* in the kernel data structures, this may be OK. +*/ +ipath_dev_err (dd,"enable unit %d failed: error %d\n" , + dd->ipath_unit, -ret); + goto bail_devdata; + } + addr =pci_resource_start (pdev,0 ); + len =pci_resource_len (pdev,0 ); +ipath_cdbg (VERBOSE ,"regbase (0) %llx len %d irq %x, vend %x/%x " +"driver_data %lx\n" , addr, len, pdev->irq, ent->vendor, + ent->device, ent->driver_data); + +read_bars (dd, pdev, &bar0, &bar1); + +if (!bar1 && !(bar0 & ~0xf )) { +if (addr) { +dev_info (&pdev->dev,"BAR is 0 (probable RESET), " +"rewriting as %llx\n" , addr); + ret =pci_write_config_dword ( + pdev,PCI_BASE_ADDRESS_0 , addr); +if (ret) { +ipath_dev_err (dd,"rewrite of BAR0 " +"failed: err %d\n" , -ret); + goto bail_disable; + } + ret =pci_write_config_dword ( + pdev,PCI_BASE_ADDRESS_1 , addr >>32 ); +if (ret) { +ipath_dev_err (dd,"rewrite of BAR1 " +"failed: err %d\n" , -ret); + goto bail_disable; + } + }else { +ipath_dev_err (dd,"BAR is 0 (probable RESET), " +"not usable until reboot\n" ); + ret = -ENODEV ; + goto bail_disable; + } + } + + ret =pci_request_regions (pdev,IPATH_DRV_NAME ); +if (ret) { +dev_info (&pdev->dev,"pci_request_regions unit %u fails: " +"err %d\n" , dd->ipath_unit, -ret); + goto bail_disable; + } + + ret =pci_set_dma_mask (pdev,DMA_64BIT_MASK ); +if (ret) { +dev_info (&pdev->dev,"pci_set_dma_mask unit %u " +"fails: %d\n" , dd->ipath_unit, ret); + goto bail_regions; + } + +pci_set_master (pdev); + +/* +* Save BARs to rewrite after device reset. Save all 64 bits of +* BAR, just in case. +*/ + dd->ipath_pcibar0 = addr; + dd->ipath_pcibar1 = addr >>32 ; + dd->ipath_deviceid = ent->device;/* save for later use */ + dd->ipath_vendorid = ent->vendor; + +/* setup the chip-specific functions, as early as possible. */ +switch (ent->device) { +case PCI_DEVICE_ID_INFINIPATH_HT : +ipath_init_ht400_funcs (dd); +break ; +case PCI_DEVICE_ID_INFINIPATH_PE800 : +ipath_init_pe800_funcs (dd); +break ; +default : +ipath_dev_err (dd,"Found unknown PathScale deviceid 0x%x, " +"failing\n" , ent->device); +return -ENODEV ; + } + +for (j =0 ; j <6 ; j++) { +if (!pdev->resource[j].start) +continue ; +ipath_cdbg (VERBOSE ,"BAR %d start %lx, end %lx, len %lx\n" , + j, pdev->resource[j].start, + pdev->resource[j].end, +pci_resource_len (pdev, j)); + } + +if (!addr) { +ipath_dev_err (dd,"No valid address in BAR 0!\n" ); + ret = -ENODEV ; + goto bail_regions; + } + + dd->ipath_deviceid = ent->device;/* save for later use */ + dd->ipath_vendorid = ent->vendor; + + ret =pci_read_config_byte (pdev,PCI_REVISION_ID , &rev); +if (ret) { +ipath_dev_err (dd,"Failed to read PCI revision ID unit " +"%u: err %d\n" , dd->ipath_unit, -ret); + goto bail_regions;/* shouldn't ever happen */ + } + dd->ipath_pcirev = rev; + + dd->ipath_kregbase =ioremap_nocache (addr, len); + +if (!dd->ipath_kregbase) { +ipath_dbg ("Unable to map io addr %llx to kvirt, failing\n" , + addr); + ret = -ENOMEM ; + goto bail_iounmap; + } + dd->ipath_kregend = (u64 __iomem *) + ((void __iomem *)dd->ipath_kregbase + len); + dd->ipath_physaddr = addr;/* used for io_remap, etc. */ +/* for user mmap */ + dd->ipath_kregvirt = (u64 __iomem *)phys_to_virt (addr); +ipath_cdbg (VERBOSE ,"mapped io addr %llx to kregbase %p " +"kregvirt %p\n" , addr, dd->ipath_kregbase, + dd->ipath_kregvirt); + +/* +* clear ipath_flags here instead of in ipath_init_chip as it is set +* by ipath_setup_htconfig. +*/ + dd->ipath_flags =0 ; + +if (dd->ipath_f_bus (dd, pdev)) +ipath_dev_err (dd,"Failed to setup config space; " +"continuing anyway\n" ); + +/* +* set up our interrupt handler; SA_SHIRQ probably not needed, +* since MSI interrupts shouldn't be shared but won't hurt for now. +* check 0 irq after we return from chip-specific bus setup, since +* that can affect this due to setup +*/ +if (!pdev->irq) +ipath_dev_err (dd,"irq is 0, BIOS error? Interrupts won't " +"work\n" ); +else { + ret =request_irq (pdev->irq, ipath_intr,SA_SHIRQ , +IPATH_DRV_NAME , dd); +if (ret) { +ipath_dev_err (dd,"Couldn't setup irq handler, " +"irq=%u: %d\n" , pdev->irq, ret); + goto bail_iounmap; + } + } + + ret =ipath_init_chip (dd,0 );/* do the chip-specific init */ +if (ret) + goto bail_iounmap; + + ret =ipath_enable_wc (dd); + +if (ret) { +ipath_dev_err (dd,"Write combining not enabled " +"(err %d): performance may be poor\n" , + -ret); + ret =0 ; + } + +ipath_device_create_group (&pdev->dev, dd); +ipathfs_add_device (dd); +ipath_user_add (dd); +ipath_layer_add (dd); + + goto bail; + +bail_iounmap: +iounmap ((volatile void __iomem *) dd->ipath_kregbase); + +bail_regions: +pci_release_regions (pdev); + +bail_disable: +pci_disable_device (pdev); + +bail_devdata: +ipath_free_devdata (pdev, dd); + +bail_rcvhdrtail: +cleanup_port0_rcvhdrtail (pdev); + +bail: +return ret; +} + +static void __devexit ipath_remove_one(struct pci_dev *pdev) +{ +struct ipath_devdata *dd; + +ipath_cdbg (VERBOSE ,"removing, pdev=%p\n" , pdev); +if (!pdev) +return ; + + dd =pci_get_drvdata (pdev); +ipath_layer_del (dd); +ipath_user_del (dd); +ipathfs_remove_device (dd); +ipath_device_remove_group (&pdev->dev, dd); +ipath_cdbg (VERBOSE ,"Releasing pci memory regions, dd %p, " +"unit %u\n" , dd, (u32 ) dd->ipath_unit); +if (dd->ipath_kregbase) { +ipath_cdbg (VERBOSE ,"Unmapping kregbase %p\n" , + dd->ipath_kregbase); +iounmap ((volatile void __iomem *) dd->ipath_kregbase); + dd->ipath_kregbase =NULL ; + } +pci_release_regions (pdev); +ipath_cdbg (VERBOSE ,"calling pci_disable_device\n" ); +pci_disable_device (pdev); + +ipath_free_devdata (pdev, dd); +cleanup_port0_rcvhdrtail (pdev); +} + +/* general driver use */ +DEFINE_MUTEX (ipath_mutex); + +static DEFINE_SPINLOCK (ipath_pioavail_lock); + +/** +* ipath_disarm_piobufs - cancel a range of PIO buffers +* @dd: the infinipath device +* @first: the first PIO buffer to cancel +* @cnt: the number of PIO buffers to cancel +* +* cancel a range of PIO buffers, used when they might be armed, but +* not triggered. Used at init to ensure buffer state, and also user +* process close, in case it died while writing to a PIO buffer +* Also after errors. +*/ +void ipath_disarm_piobufs (struct ipath_devdata *dd,unsigned first, +unsigned cnt) +{ +unsigned i, last = first + cnt; +u64 sendctrl, sendorig; + +ipath_cdbg (PKT ,"disarm %u PIObufs first=%u\n" , cnt, first); + sendorig = dd->ipath_sendctrl |INFINIPATH_S_DISARM ; +for (i = first; i < last; i++) { + sendctrl = sendorig | + (i <<INFINIPATH_S_DISARMPIOBUF_SHIFT ); +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, + sendctrl); + } + +/* +* Write it again with current value, in case ipath_sendctrl changed +* while we were looping; no critical bits that would require +* locking. +* +* Write a 0, and then the original value, reading scratch in +* between. This seems to avoid a chip timing race that causes +* pioavail updates to memory to stop. +*/ +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, +0 ); + sendorig =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, + dd->ipath_sendctrl); +} + +/** +* ipath_wait_linkstate - wait for an IB link state change to occur +* @dd: the infinipath device +* @state: the state to wait for +* @msecs: the number of milliseconds to wait +* +* wait up to msecs milliseconds for IB link state change to occur for +* now, take the easy polling route. Currently used only by +* ipath_layer_set_linkstate. Returns 0 if state reached, otherwise +* -ETIMEDOUT state can have multiple states set, for any of several +* transitions. +*/ +int ipath_wait_linkstate (struct ipath_devdata *dd,u32 state,int msecs) +{ + dd->ipath_sma_state_wanted = state; +wait_event_interruptible_timeout (ipath_sma_state_wait, + (dd->ipath_flags & state), +msecs_to_jiffies (msecs)); + dd->ipath_sma_state_wanted =0 ; + +if (!(dd->ipath_flags & state)) { +u64 val; +ipath_cdbg (SMA ,"Didn't reach linkstate %s within %u ms\n" , +/* test INIT ahead of DOWN, both can be set */ + (state &IPATH_LINKINIT ) ?"INIT" : + ((state &IPATH_LINKDOWN ) ?"DOWN" : + ((state &IPATH_LINKARMED ) ?"ARM" :"ACTIVE" )), + msecs); + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_ibcstatus); +ipath_cdbg (VERBOSE ,"ibcc=%llx ibcstatus=%llx (%s)\n" , + (unsigned long long )ipath_read_kreg64 ( + dd, dd->ipath_kregs->kr_ibcctrl), + (unsigned long long ) val, + ipath_ibcstatus_str[val &0xf ]); + } +return (dd->ipath_flags & state) ?0 : -ETIMEDOUT ; +} + +void ipath_decode_err (char *buf,size_t blen,ipath_err_t err) +{ + *buf ='\0' ; +if (err &INFINIPATH_E_RHDRLEN ) +strlcat (buf,"rhdrlen " , blen); +if (err &INFINIPATH_E_RBADTID ) +strlcat (buf,"rbadtid " , blen); +if (err &INFINIPATH_E_RBADVERSION ) +strlcat (buf,"rbadversion " , blen); +if (err &INFINIPATH_E_RHDR ) +strlcat (buf,"rhdr " , blen); +if (err &INFINIPATH_E_RLONGPKTLEN ) +strlcat (buf,"rlongpktlen " , blen); +if (err &INFINIPATH_E_RSHORTPKTLEN ) +strlcat (buf,"rshortpktlen " , blen); +if (err &INFINIPATH_E_RMAXPKTLEN ) +strlcat (buf,"rmaxpktlen " , blen); +if (err &INFINIPATH_E_RMINPKTLEN ) +strlcat (buf,"rminpktlen " , blen); +if (err &INFINIPATH_E_RFORMATERR ) +strlcat (buf,"rformaterr " , blen); +if (err &INFINIPATH_E_RUNSUPVL ) +strlcat (buf,"runsupvl " , blen); +if (err &INFINIPATH_E_RUNEXPCHAR ) +strlcat (buf,"runexpchar " , blen); +if (err &INFINIPATH_E_RIBFLOW ) +strlcat (buf,"ribflow " , blen); +if (err &INFINIPATH_E_REBP ) +strlcat (buf,"EBP " , blen); +if (err &INFINIPATH_E_SUNDERRUN ) +strlcat (buf,"sunderrun " , blen); +if (err &INFINIPATH_E_SPIOARMLAUNCH ) +strlcat (buf,"spioarmlaunch " , blen); +if (err &INFINIPATH_E_SUNEXPERRPKTNUM ) +strlcat (buf,"sunexperrpktnum " , blen); +if (err &INFINIPATH_E_SDROPPEDDATAPKT ) +strlcat (buf,"sdroppeddatapkt " , blen); +if (err &INFINIPATH_E_SDROPPEDSMPPKT ) +strlcat (buf,"sdroppedsmppkt " , blen); +if (err &INFINIPATH_E_SMAXPKTLEN ) +strlcat (buf,"smaxpktlen " , blen); +if (err &INFINIPATH_E_SMINPKTLEN ) +strlcat (buf,"sminpktlen " , blen); +if (err &INFINIPATH_E_SUNSUPVL ) +strlcat (buf,"sunsupVL " , blen); +if (err &INFINIPATH_E_SPKTLEN ) +strlcat (buf,"spktlen " , blen); +if (err &INFINIPATH_E_INVALIDADDR ) +strlcat (buf,"invalidaddr " , blen); +if (err &INFINIPATH_E_RICRC ) +strlcat (buf,"CRC " , blen); +if (err &INFINIPATH_E_RVCRC ) +strlcat (buf,"VCRC " , blen); +if (err &INFINIPATH_E_RRCVEGRFULL ) +strlcat (buf,"rcvegrfull " , blen); +if (err &INFINIPATH_E_RRCVHDRFULL ) +strlcat (buf,"rcvhdrfull " , blen); +if (err &INFINIPATH_E_IBSTATUSCHANGED ) +strlcat (buf,"ibcstatuschg " , blen); +if (err &INFINIPATH_E_RIBLOSTLINK ) +strlcat (buf,"riblostlink " , blen); +if (err &INFINIPATH_E_HARDWARE ) +strlcat (buf,"hardware " , blen); +if (err &INFINIPATH_E_RESET ) +strlcat (buf,"reset " , blen); +} + +/** +* get_rhf_errstring - decode RHF errors +* @err: the err number +* @msg: the output buffer +* @len: the length of the output buffer +* +* only used one place now, may want more later +*/ +static void get_rhf_errstring (u32 err,char *msg,size_t len) +{ +/* if no errors, and so don't need to check what's first */ + *msg ='\0' ; + +if (err &INFINIPATH_RHF_H_ICRCERR ) +strlcat (msg,"icrcerr " , len); +if (err &INFINIPATH_RHF_H_VCRCERR ) +strlcat (msg,"vcrcerr " , len); +if (err &INFINIPATH_RHF_H_PARITYERR ) +strlcat (msg,"parityerr " , len); +if (err &INFINIPATH_RHF_H_LENERR ) +strlcat (msg,"lenerr " , len); +if (err &INFINIPATH_RHF_H_MTUERR ) +strlcat (msg,"mtuerr " , len); +if (err &INFINIPATH_RHF_H_IHDRERR ) +/* infinipath hdr checksum error */ +strlcat (msg,"ipathhdrerr " , len); +if (err &INFINIPATH_RHF_H_TIDERR ) +strlcat (msg,"tiderr " , len); +if (err &INFINIPATH_RHF_H_MKERR ) +/* bad port, offset, etc. */ +strlcat (msg,"invalid ipathhdr " , len); +if (err &INFINIPATH_RHF_H_IBERR ) +strlcat (msg,"iberr " , len); +if (err &INFINIPATH_RHF_L_SWA ) +strlcat (msg,"swA " , len); +if (err &INFINIPATH_RHF_L_SWB ) +strlcat (msg,"swB " , len); +} + +/** +* ipath_get_egrbuf - get an eager buffer +* @dd: the infinipath device +* @bufnum: the eager buffer to get +* @err: unused +* +* must only be called if ipath_pd[port] is known to be allocated +*/ +static inline void *ipath_get_egrbuf (struct ipath_devdata *dd,u32 bufnum, +int err) +{ +return dd->ipath_port0_skbs ? + (void *)dd->ipath_port0_skbs[bufnum]->data :NULL ; +} + +/** +* ipath_alloc_skb - allocate an skb and buffer with possible constraints +* @dd: the infinipath device +* @gfp_mask: the sk_buff SFP mask +*/ +struct sk_buff *ipath_alloc_skb (struct ipath_devdata *dd, +gfp_t gfp_mask) +{ +struct sk_buff *skb; +u32 len; + +/* +* Only fully supported way to handle this is to allocate lots +* extra, align as needed, and then do skb_reserve(). That wastes +* a lot of memory... I'll have to hack this into infinipath_copy +* also. +*/ + +/* +* We need 4 extra bytes for unaligned transfer copying +*/ +if (dd->ipath_flags &IPATH_4BYTE_TID ) { +/* we need a 4KB multiple alignment, and there is no way +* to do it except to allocate extra and then skb_reserve +* enough to bring it up to the right alignment. +*/ + len = dd->ipath_ibmaxlen +4 + (1 <<11 ) -1 ; + } +else + len = dd->ipath_ibmaxlen +4 ; + skb =__dev_alloc_skb (len, gfp_mask); +if (!skb) { +ipath_dev_err (dd,"Failed to allocate skbuff, length %u\n" , + len); + goto bail; + } +if (dd->ipath_flags &IPATH_4BYTE_TID ) { +u32 una = ((1 <<11 ) -1 ) & (unsigned long )(skb->data +4 ); +if (una) +skb_reserve (skb,4 + (1 <<11 ) - una); +else +skb_reserve (skb,4 ); + }else +skb_reserve (skb,4 ); + +bail: +return skb; +} + +/** +* ipath_rcv_layer - receive a packet for the layered (ethernet) driver +* @dd: the infinipath device +* @etail: the sk_buff number +* @tlen: the total packet length +* @hdr: the ethernet header +* +* Separate routine for better overall optimization +*/ +static void ipath_rcv_layer (struct ipath_devdata *dd,u32 etail, +u32 tlen,struct ether_header *hdr) +{ +u32 elen; +u8 pad, *bthbytes; +struct sk_buff *skb, *nskb; + +if (dd->ipath_port0_skbs && hdr->sub_opcode ==OPCODE_ENCAP ) { +/* +* Allocate a new sk_buff to replace the one we give +* to the network stack. +*/ + nskb =ipath_alloc_skb (dd,GFP_ATOMIC ); +if (!nskb) { +/* count OK packets that we drop */ + ipath_stats.sps_krdrops++; +return ; + } + + bthbytes = (u8 *) hdr->bth; + pad = (bthbytes[1 ] >>4 ) &3 ; +/* +CRC32 */ + elen = tlen - (sizeof (*hdr) + pad +sizeof (u32)); + + skb = dd->ipath_port0_skbs[etail]; + dd->ipath_port0_skbs[etail] = nskb; +skb_put (skb, elen); + + dd->ipath_f_put_tid (dd, etail + (u64 __iomem *) + ((char __iomem *) dd->ipath_kregbase + + dd->ipath_rcvegrbase),0 , +virt_to_phys (nskb->data)); + +__ipath_layer_rcv (dd, hdr, skb); + +/* another ether packet received */ + ipath_stats.sps_ether_rpkts++; + } +else if (hdr->sub_opcode ==OPCODE_LID_ARP ) +__ipath_layer_rcv_lid (dd, hdr); +} + +/* +* ipath_kreceive - receive a packet +* @dd: the infinipath device +* +* called from interrupt handler for errors or receive interrupt +*/ +void ipath_kreceive (struct ipath_devdata *dd) +{ +u64 *rc; +void *ebuf; +const u32 rsize = dd->ipath_rcvhdrentsize;/* words */ +const u32 maxcnt = dd->ipath_rcvhdrcnt * rsize;/* words */ +u32 etail =-1 , l, hdrqtail; +struct ips_message_header *hdr; +u32 eflags, i, etype, tlen, pkttot =0 ; +static u64 totcalls;/* stats, may eventually remove */ +char emsg[128 ]; + +if (!dd->ipath_hdrqtailptr) { +ipath_dev_err (dd, +"hdrqtailptr not set, can't do receives\n" ); + goto bail; + } + +/* There is already a thread processing this queue. */ +if (test_and_set_bit (0 , &dd->ipath_rcv_pending)) + goto bail; + +if (dd->ipath_port0head == + (u32 )le64_to_cpu (*dd->ipath_hdrqtailptr)) + goto done; + +gotmore: +/* +* read only once at start. If in flood situation, this helps +* performance slightly. If more arrive while we are processing, +* we'll come back here and do them +*/ + hdrqtail = (u32 )le64_to_cpu (*dd->ipath_hdrqtailptr); + +for (i =0 , l = dd->ipath_port0head; l != hdrqtail; i++) { +u32 qp; +u8 *bthbytes; + + rc = (u64 *) (dd->ipath_pd[0 ]->port_rcvhdrq + (l <<2 )); + hdr = (struct ips_message_header *)&rc[1 ]; +/* +* could make a network order version of IPATH_KD_QP, and +* do the obvious shift before masking to speed this up. +*/ + qp =ntohl (hdr->bth[1 ]) &0xffffff ; + bthbytes = (u8 *) hdr->bth; + + eflags =ips_get_hdr_err_flags ((__le32 *) rc); + etype =ips_get_rcv_type ((__le32 *) rc); +/* total length */ + tlen =ips_get_length_in_bytes ((__le32 *) rc); + ebuf =NULL ; +if (etype !=RCVHQ_RCV_TYPE_EXPECTED ) { +/* +* it turns out that the chips uses an eager buffer +* for all non-expected packets, whether it "needs" +* one or not. So always get the index, but don't +* set ebuf (so we try to copy data) unless the +* length requires it. +*/ + etail =ips_get_index ((__le32 *) rc); +if (tlen >sizeof (*hdr) || + etype ==RCVHQ_RCV_TYPE_NON_KD ) + ebuf =ipath_get_egrbuf (dd, etail,0 ); + } + +/* +* both tiderr and ipathhdrerr are set for all plain IB +* packets; only ipathhdrerr should be set. +*/ + +if (etype !=RCVHQ_RCV_TYPE_NON_KD && etype != +RCVHQ_RCV_TYPE_ERROR &&ips_get_ipath_ver ( + hdr->iph.ver_port_tid_offset) != +IPS_PROTO_VERSION ) { +ipath_cdbg (PKT ,"Bad InfiniPath protocol version " +"%x\n" , etype); + } + +if (eflags & ~(INFINIPATH_RHF_H_TIDERR | +INFINIPATH_RHF_H_IHDRERR )) { +get_rhf_errstring (eflags, emsg,sizeof emsg); +ipath_cdbg (PKT ,"RHFerrs %x hdrqtail=%x typ=%u " +"tlen=%x opcode=%x egridx=%x: %s\n" , + eflags, l, etype, tlen, bthbytes[0 ], +ips_get_index ((__le32 *) rc), emsg); + }else if (etype ==RCVHQ_RCV_TYPE_NON_KD ) { +int ret =__ipath_verbs_rcv (dd, rc +1 , + ebuf, tlen); +if (ret == -ENODEV ) +ipath_cdbg (VERBOSE , +"received IB packet, " +"not SMA (QP=%x)\n" , qp); + }else if (etype ==RCVHQ_RCV_TYPE_EAGER ) { +if (qp ==IPATH_KD_QP && + bthbytes[0 ] == ipath_layer_rcv_opcode && + ebuf) +ipath_rcv_layer (dd, etail, tlen, + (struct ether_header *)hdr); +else +ipath_cdbg (PKT ,"typ %x, opcode %x (eager, " +"qp=%x), len %x; ignored\n" , + etype, bthbytes[0 ], qp, tlen); + } +else if (etype ==RCVHQ_RCV_TYPE_EXPECTED ) +ipath_dbg ("Bug: Expected TID, opcode %x; ignored\n" , +be32_to_cpu (hdr->bth[0 ]) &0xff ); +else if (eflags & (INFINIPATH_RHF_H_TIDERR | +INFINIPATH_RHF_H_IHDRERR )) { +/* +* This is a type 3 packet, only the LRH is in the +* rcvhdrq, the rest of the header is in the eager +* buffer. +*/ +u8 opcode; +if (ebuf) { + bthbytes = (u8 *) ebuf; + opcode = *bthbytes; + } +else + opcode =0 ; +get_rhf_errstring (eflags, emsg,sizeof emsg); +ipath_dbg ("Err %x (%s), opcode %x, egrbuf %x, " +"len %x\n" , eflags, emsg, opcode, etail, + tlen); + }else { +/* +* error packet, type of error unknown. +* Probably type 3, but we don't know, so don't +* even try to print the opcode, etc. +*/ +ipath_dbg ("Error Pkt, but no eflags! egrbuf %x, " +"len %x\nhdrq@%lx;hdrq+%x rhf: %llx; " +"hdr %llx %llx %llx %llx %llx\n" , + etail, tlen, (unsigned long ) rc, l, + (unsigned long long ) rc[0 ], + (unsigned long long ) rc[1 ], + (unsigned long long ) rc[2 ], + (unsigned long long ) rc[3 ], + (unsigned long long ) rc[4 ], + (unsigned long long ) rc[5 ]); + } + l += rsize; +if (l >= maxcnt) + l =0 ; +/* +* update for each packet, to help prevent overflows if we +* have lots of packets. +*/ + (void )ipath_write_ureg (dd, ur_rcvhdrhead, + dd->ipath_rhdrhead_intr_off | l,0 ); +if (etype !=RCVHQ_RCV_TYPE_EXPECTED ) + (void )ipath_write_ureg (dd, ur_rcvegrindexhead, + etail,0 ); + } + + pkttot += i; + + dd->ipath_port0head = l; + +if (hdrqtail != (u32 )le64_to_cpu (*dd->ipath_hdrqtailptr)) +/* more arrived while we handled first batch */ + goto gotmore; + +if (pkttot > ipath_stats.sps_maxpkts_call) + ipath_stats.sps_maxpkts_call = pkttot; + ipath_stats.sps_port0pkts += pkttot; + ipath_stats.sps_avgpkts_call = + ipath_stats.sps_port0pkts / ++totcalls; + +done: +clear_bit (0 , &dd->ipath_rcv_pending); +smp_mb__after_clear_bit (); + +bail:; +} + +/** +* ipath_update_pio_bufs - update shadow copy of the PIO availability map +* @dd: the infinipath device +* +* called whenever our local copy indicates we have run out of send buffers +* NOTE: This can be called from interrupt context by some code +* and from non-interrupt context by ipath_getpiobuf(). +*/ + +static void ipath_update_pio_bufs (struct ipath_devdata *dd) +{ +unsigned long flags; +int i; +const unsigned piobregs = (unsigned )dd->ipath_pioavregs; + +/* If the generation (check) bits have changed, then we update the +* busy bit for the corresponding PIO buffer. This algorithm will +* modify positions to the value they already have in some cases +* (i.e., no change), but it's faster than changing only the bits +* that have changed. +* +* We would like to do this atomicly, to avoid spinlocks in the +* critical send path, but that's not really possible, given the +* type of changes, and that this routine could be called on +* multiple cpu's simultaneously, so we lock in this routine only, +* to avoid conflicting updates; all we change is the shadow, and +* it's a single 64 bit memory location, so by definition the update +* is atomic in terms of what other cpu's can see in testing the +* bits. The spin_lock overhead isn't too bad, since it only +* happens when all buffers are in use, so only cpu overhead, not +* latency or bandwidth is affected. +*/ +#define _IPATH_ALL_CHECKBITS 0x5555555555555555ULL +if (!dd->ipath_pioavailregs_dma) { +ipath_dbg ("Update shadow pioavail, but regs_dma NULL!\n" ); +return ; + } +if (ipath_debug & __IPATH_VERBDBG) { +/* only if packet debug and verbose */ +volatile __le64 *dma = dd->ipath_pioavailregs_dma; +unsigned long *shadow = dd->ipath_pioavailshadow; + +ipath_cdbg (PKT ,"Refill avail, dma0=%llx shad0=%lx, " +"d1=%llx s1=%lx, d2=%llx s2=%lx, d3=%llx " +"s3=%lx\n" , + (unsigned long long )le64_to_cpu (dma[0 ]), + shadow[0 ], + (unsigned long long )le64_to_cpu (dma[1 ]), + shadow[1 ], + (unsigned long long )le64_to_cpu (dma[2 ]), + shadow[2 ], + (unsigned long long )le64_to_cpu (dma[3 ]), + shadow[3 ]); +if (piobregs >4 ) +ipath_cdbg ( +PKT ,"2nd group, dma4=%llx shad4=%lx, " +"d5=%llx s5=%lx, d6=%llx s6=%lx, " +"d7=%llx s7=%lx\n" , + (unsigned long long )le64_to_cpu (dma[4 ]), + shadow[4 ], + (unsigned long long )le64_to_cpu (dma[5 ]), + shadow[5 ], + (unsigned long long )le64_to_cpu (dma[6 ]), + shadow[6 ], + (unsigned long long )le64_to_cpu (dma[7 ]), + shadow[7 ]); + } +spin_lock_irqsave (&ipath_pioavail_lock, flags); +for (i =0 ; i < piobregs; i++) { +u64 pchbusy, pchg, piov, pnew; +/* +* Chip Errata: bug 6641; even and odd qwords>3 are swapped +*/ +if (i >3 ) { +if (i &1 ) + piov =le64_to_cpu ( + dd->ipath_pioavailregs_dma[i -1 ]); +else + piov =le64_to_cpu ( + dd->ipath_pioavailregs_dma[i +1 ]); + }else + piov =le64_to_cpu (dd->ipath_pioavailregs_dma[i]); + pchg = _IPATH_ALL_CHECKBITS & + ~(dd->ipath_pioavailshadow[i] ^ piov); + pchbusy = pchg <<INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT ; +if (pchg && (pchbusy & dd->ipath_pioavailshadow[i])) { + pnew = dd->ipath_pioavailshadow[i] & ~pchbusy; + pnew |= piov & pchbusy; + dd->ipath_pioavailshadow[i] = pnew; + } + } +spin_unlock_irqrestore (&ipath_pioavail_lock, flags); +} + +/** +* ipath_setrcvhdrsize - set the receive header size +* @dd: the infinipath device +* @rhdrsize: the receive header size +* +* called from user init code, and also layered driver init +*/ +int ipath_setrcvhdrsize (struct ipath_devdata *dd,unsigned rhdrsize) +{ +int ret =0 ; + +if (dd->ipath_flags &IPATH_RCVHDRSZ_SET ) { +if (dd->ipath_rcvhdrsize != rhdrsize) { +dev_info (&dd->pcidev->dev, +"Error: can't set protocol header " +"size %u, already %u\n" , + rhdrsize, dd->ipath_rcvhdrsize); + ret = -EAGAIN ; + }else +ipath_cdbg (VERBOSE ,"Reuse same protocol header " +"size %u\n" , dd->ipath_rcvhdrsize); + }else if (rhdrsize > (dd->ipath_rcvhdrentsize - + (sizeof (u64) /sizeof (u32)))) { +ipath_dbg ("Error: can't set protocol header size %u " +"(> max %u)\n" , rhdrsize, + dd->ipath_rcvhdrentsize - + (u32) (sizeof (u64) /sizeof (u32))); + ret = -EOVERFLOW ; + }else { + dd->ipath_flags |=IPATH_RCVHDRSZ_SET ; + dd->ipath_rcvhdrsize = rhdrsize; +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvhdrsize, + dd->ipath_rcvhdrsize); +ipath_cdbg (VERBOSE ,"Set protocol header size to %u\n" , + dd->ipath_rcvhdrsize); + } +return ret; +} + +/** +* ipath_getpiobuf - find an available pio buffer +* @dd: the infinipath device +* @pbufnum: the buffer number is placed here +* +* do appropriate marking as busy, etc. +* returns buffer number if one found (>=0), negative number is error. +* Used by ipath_sma_send_pkt and ipath_layer_send +*/ +u32 __iomem *ipath_getpiobuf (struct ipath_devdata *dd,u32 * pbufnum) +{ +int i, j, starti, updated =0 ; +unsigned piobcnt, iter; +unsigned long flags; +unsigned long *shadow = dd->ipath_pioavailshadow; +u32 __iomem *buf; + + piobcnt = (unsigned )(dd->ipath_piobcnt2k + + dd->ipath_piobcnt4k); + starti = dd->ipath_lastport_piobuf; + iter = piobcnt - starti; +if (dd->ipath_upd_pio_shadow) { +/* +* Minor optimization. If we had no buffers on last call, +* start out by doing the update; continue and do scan even +* if no buffers were updated, to be paranoid +*/ +ipath_update_pio_bufs (dd); +/* we scanned here, don't do it at end of scan */ + updated =1 ; + i = starti; + }else + i = dd->ipath_lastpioindex; + +rescan: +/* +* while test_and_set_bit() is atomic, we do that and then the +* change_bit(), and the pair is not. See if this is the cause +* of the remaining armlaunch errors. +*/ +spin_lock_irqsave (&ipath_pioavail_lock, flags); +for (j =0 ; j < iter; j++, i++) { +if (i >= piobcnt) + i = starti; +/* +* To avoid bus lock overhead, we first find a candidate +* buffer, then do the test and set, and continue if that +* fails. +*/ +if (test_bit ((2 * i) +1 , shadow) || +test_and_set_bit ((2 * i) +1 , shadow)) +continue ; +/* flip generation bit */ +change_bit (2 * i, shadow); +break ; + } +spin_unlock_irqrestore (&ipath_pioavail_lock, flags); + +if (j == iter) { +volatile __le64 *dma = dd->ipath_pioavailregs_dma; + +/* +* first time through; shadow exhausted, but may be real +* buffers available, so go see; if any updated, rescan +* (once) +*/ +if (!updated) { +ipath_update_pio_bufs (dd); + updated =1 ; + i = starti; + goto rescan; + } + dd->ipath_upd_pio_shadow =1 ; +/* +* not atomic, but if we lose one once in a while, that's OK +*/ + ipath_stats.sps_nopiobufs++; +if (!(++dd->ipath_consec_nopiobuf %100000 )) { +ipath_dbg ( +"%u pio sends with no bufavail; dmacopy: " +"%llx %llx %llx %llx; shadow: " +"%lx %lx %lx %lx\n" , + dd->ipath_consec_nopiobuf, + (unsigned long long )le64_to_cpu (dma[0 ]), + (unsigned long long )le64_to_cpu (dma[1 ]), + (unsigned long long )le64_to_cpu (dma[2 ]), + (unsigned long long )le64_to_cpu (dma[3 ]), + shadow[0 ], shadow[1 ], shadow[2 ], + shadow[3 ]); +/* +* 4 buffers per byte, 4 registers above, cover rest +* below +*/ +if ((dd->ipath_piobcnt2k + dd->ipath_piobcnt4k) > + (sizeof (shadow[0 ]) *4 *4 )) +ipath_dbg ("2nd group: dmacopy: %llx %llx " +"%llx %llx; shadow: %lx %lx " +"%lx %lx\n" , + (unsigned long long ) +le64_to_cpu (dma[4 ]), + (unsigned long long ) +le64_to_cpu (dma[5 ]), + (unsigned long long ) +le64_to_cpu (dma[6 ]), + (unsigned long long ) +le64_to_cpu (dma[7 ]), + shadow[4 ], shadow[5 ], + shadow[6 ], shadow[7 ]); + } + buf =NULL ; + goto bail; + } + +if (updated) +/* +* ran out of bufs, now some (at least this one we just +* got) are now available, so tell the layered driver. +*/ +__ipath_layer_intr (dd,IPATH_LAYER_INT_SEND_CONTINUE ); + +/* +* set next starting place. Since it's just an optimization, +* it doesn't matter who wins on this, so no locking +*/ + dd->ipath_lastpioindex = i +1 ; +if (dd->ipath_upd_pio_shadow) + dd->ipath_upd_pio_shadow =0 ; +if (dd->ipath_consec_nopiobuf) + dd->ipath_consec_nopiobuf =0 ; +if (i < dd->ipath_piobcnt2k) + buf = (u32 __iomem *) (dd->ipath_pio2kbase + + i * dd->ipath_palign); +else + buf = (u32 __iomem *) + (dd->ipath_pio4kbase + + (i - dd->ipath_piobcnt2k) * dd->ipath_4kalign); +ipath_cdbg (VERBOSE ,"Return piobuf%u %uk @ %p\n" , + i, (i < dd->ipath_piobcnt2k) ?2 :4 , buf); +if (pbufnum) + *pbufnum = i; + +bail: +return buf; +} + +/** +* ipath_create_rcvhdrq - create a receive header queue +* @dd: the infinipath device +* @pd: the port data +* +* this *must* be physically contiguous memory, and for now, +* that limits it to what kmalloc can do. +*/ +int ipath_create_rcvhdrq (struct ipath_devdata *dd, +struct ipath_portdata *pd) +{ +int ret =0 , amt; + + amt =ALIGN (dd->ipath_rcvhdrcnt * dd->ipath_rcvhdrentsize * +sizeof (u32),PAGE_SIZE ); +if (!pd->port_rcvhdrq) { +/* +* not using REPEAT isn't viable; at 128KB, we can easily +* fail this. The problem with REPEAT is we can block here +* "forever". There isn't an inbetween, unfortunately. We +* could reduce the risk by never freeing the rcvhdrq except +* at unload, but even then, the first time a port is used, +* we could delay for some time... +*/ +gfp_t gfp_flags =GFP_USER | __GFP_COMP; + + pd->port_rcvhdrq =dma_alloc_coherent ( + &dd->pcidev->dev, amt, &pd->port_rcvhdrq_phys, + gfp_flags); + +if (!pd->port_rcvhdrq) { +ipath_dev_err (dd,"attempt to allocate %d bytes " +"for port %u rcvhdrq failed\n" , + amt, pd->port_port); + ret = -ENOMEM ; + goto bail; + } + + pd->port_rcvhdrq_size = amt; + +ipath_cdbg (VERBOSE ,"%d pages at %p (phys %lx) size=%lu " +"for port %u rcvhdr Q\n" , + amt >>PAGE_SHIFT , pd->port_rcvhdrq, + (unsigned long ) pd->port_rcvhdrq_phys, + (unsigned long ) pd->port_rcvhdrq_size, + pd->port_port); + }else { +/* +* clear for security, sanity, and/or debugging, each +* time we reuse +*/ +memset (pd->port_rcvhdrq,0 , amt); + } + +/* +* tell chip each time we init it, even if we are re-using previous +* memory (we zero it at process close) +*/ +ipath_cdbg (VERBOSE ,"writing port %d rcvhdraddr as %lx\n" , + pd->port_port, (unsigned long ) pd->port_rcvhdrq_phys); +ipath_write_kreg_port (dd, dd->ipath_kregs->kr_rcvhdraddr, + pd->port_port, pd->port_rcvhdrq_phys); + + ret =0 ; +bail: +return ret; +} + +int ipath_waitfor_complete (struct ipath_devdata *dd,ipath_kreg reg_id, +u64 bits_to_wait_for,u64 * valp) +{ +unsigned long timeout; +u64 lastval, val; +int ret; + + lastval =ipath_read_kreg64 (dd, reg_id); +/* wait a ridiculously long time */ + timeout = jiffies +msecs_to_jiffies (5 ); +do { + val =ipath_read_kreg64 (dd, reg_id); +/* set so they have something, even on failures. */ + *valp = val; +if ((val & bits_to_wait_for) == bits_to_wait_for) { + ret =0 ; +break ; + } +if (val != lastval) +ipath_cdbg (VERBOSE ,"Changed from %llx to %llx, " +"waiting for %llx bits\n" , + (unsigned long long ) lastval, + (unsigned long long ) val, + (unsigned long long ) bits_to_wait_for); +cond_resched (); +if (time_after (jiffies, timeout)) { +ipath_dbg ("Didn't get bits %llx in register 0x%x, " +"got %llx\n" , + (unsigned long long ) bits_to_wait_for, + reg_id, (unsigned long long ) *valp); + ret = -ENODEV ; +break ; + } + }while (1 ); + +return ret; +} + +/** +* ipath_waitfor_mdio_cmdready - wait for last command to complete +* @dd: the infinipath device +* +* Like ipath_waitfor_complete(), but we wait for the CMDVALID bit to go +* away indicating the last command has completed. It doesn't return data +*/ +int ipath_waitfor_mdio_cmdready (struct ipath_devdata *dd) +{ +unsigned long timeout; +u64 val; +int ret; + +/* wait a ridiculously long time */ + timeout = jiffies +msecs_to_jiffies (5 ); +do { + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_mdio); +if (!(val &IPATH_MDIO_CMDVALID )) { + ret =0 ; +break ; + } +cond_resched (); +if (time_after (jiffies, timeout)) { +ipath_dbg ("CMDVALID stuck in mdio reg? (%llx)\n" , + (unsigned long long ) val); + ret = -ENODEV ; +break ; + } + }while (1 ); + +return ret; +} + +void ipath_set_ib_lstate (struct ipath_devdata *dd,int which) +{ +static const char *what[4 ] = { + [0 ] ="DOWN" , + [INFINIPATH_IBCC_LINKCMD_INIT ] ="INIT" , + [INFINIPATH_IBCC_LINKCMD_ARMED ] ="ARMED" , + [INFINIPATH_IBCC_LINKCMD_ACTIVE ] ="ACTIVE" + }; +ipath_cdbg (SMA ,"Trying to move unit %u to %s, current ltstate " +"is %s\n" , dd->ipath_unit, + what[(which >>INFINIPATH_IBCC_LINKCMD_SHIFT ) & +INFINIPATH_IBCC_LINKCMD_MASK ], + ipath_ibcstatus_str[ + (ipath_read_kreg64 + (dd, dd->ipath_kregs->kr_ibcstatus) >> +INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT ) & +INFINIPATH_IBCS_LINKTRAININGSTATE_MASK ]); + +ipath_write_kreg (dd, dd->ipath_kregs->kr_ibcctrl, + dd->ipath_ibcctrl | which); +} + +/** +* ipath_read_kreg64_port - read a device's per-port 64-bit kernel register +* @dd: the infinipath device +* @regno: the register number to read +* @port: the port containing the register +* +* Registers that vary with the chip implementation constants (port) +* use this routine. +*/ +u64 ipath_read_kreg64_port (const struct ipath_devdata *dd,ipath_kreg regno, +unsigned port) +{ +u16 where; + +if (port < dd->ipath_portcnt && + (regno == dd->ipath_kregs->kr_rcvhdraddr || + regno == dd->ipath_kregs->kr_rcvhdrtailaddr)) + where = regno + port; +else + where =-1 ; + +return ipath_read_kreg64 (dd, where); +} + +/** +* ipath_write_kreg_port - write a device's per-port 64-bit kernel register +* @dd: the infinipath device +* @regno: the register number to write +* @port: the port containing the register +* @value: the value to write +* +* Registers that vary with the chip implementation constants (port) +* use this routine. +*/ +void ipath_write_kreg_port (const struct ipath_devdata *dd,ipath_kreg regno, +unsigned port,u64 value) +{ +u16 where; + +if (port < dd->ipath_portcnt && + (regno == dd->ipath_kregs->kr_rcvhdraddr || + regno == dd->ipath_kregs->kr_rcvhdrtailaddr)) + where = regno + port; +else + where =-1 ; + +ipath_write_kreg (dd, where, value); +} + +/** +* ipath_shutdown_device - shut down a device +* @dd: the infinipath device +* +* This is called to make the device quiet when we are about to +* unload the driver, and also when the device is administratively +* disabled. It does not free any data structures. +* Everything it does has to be setup again by ipath_init_chip(dd,1) +*/ +void ipath_shutdown_device (struct ipath_devdata *dd) +{ +u64 val; + +ipath_dbg ("Shutting down the device\n" ); + + dd->ipath_flags |=IPATH_LINKUNK ; + dd->ipath_flags &= ~(IPATH_INITTED |IPATH_LINKDOWN | +IPATH_LINKINIT |IPATH_LINKARMED | +IPATH_LINKACTIVE ); + *dd->ipath_statusp &= ~(IPATH_STATUS_IB_CONF | +IPATH_STATUS_IB_READY ); + +/* mask interrupts, but not errors */ +ipath_write_kreg (dd, dd->ipath_kregs->kr_intmask,0ULL ); + + dd->ipath_rcvctrl =0 ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); + +/* +* gracefully stop all sends allowing any in progress to trickle out +* first. +*/ +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl,0ULL ); +/* flush it */ + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); +/* +* enough for anything that's going to trickle out to have actually +* done so. +*/ +udelay (5 ); + +/* +* abort any armed or launched PIO buffers that didn't go. (self +* clearing). Will cause any packet currently being transmitted to +* go out with an EBP, and may also cause a short packet error on +* the receiver. +*/ +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, +INFINIPATH_S_ABORT ); + +ipath_set_ib_lstate (dd,INFINIPATH_IBCC_LINKINITCMD_DISABLE << +INFINIPATH_IBCC_LINKINITCMD_SHIFT ); + +/* +* we are shutting down, so tell the layered driver. We don't do +* this on just a link state change, much like ethernet, a cable +* unplug, etc. doesn't change driver state +*/ +ipath_layer_intr (dd,IPATH_LAYER_INT_IF_DOWN ); + +/* disable IBC */ + dd->ipath_control &= ~INFINIPATH_C_LINKENABLE ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_control, + dd->ipath_control); + +/* +* clear SerdesEnable and turn the leds off; do this here because +* we are unloading, so don't count on interrupts to move along +* Turn the LEDs off explictly for the same reason. +*/ + dd->ipath_f_quiet_serdes (dd); + dd->ipath_f_setextled (dd,0 ,0 ); + +if (dd->ipath_stats_timer_active) { +del_timer_sync (&dd->ipath_stats_timer); + dd->ipath_stats_timer_active =0 ; + } + +/* +* clear all interrupts and errors, so that the next time the driver +* is loaded or device is enabled, we know that whatever is set +* happened while we were unloaded +*/ +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrclear, + ~0ULL & ~INFINIPATH_HWE_MEMBISTFAILED ); +ipath_write_kreg (dd, dd->ipath_kregs->kr_errorclear,-1LL ); +ipath_write_kreg (dd, dd->ipath_kregs->kr_intclear,-1LL ); +} + +/** +* ipath_free_pddata - free a port's allocated data +* @dd: the infinipath device +* @port: the port +* @freehdrq: free the port data structure if true +* +* when closing, free up any allocated data for a port, if the +* reference count goes to zero +* Note: this also optionally frees the portdata itself! +* Any changes here have to be matched up with the reinit case +* of ipath_init_chip(), which calls this routine on reinit after reset. +*/ +void ipath_free_pddata (struct ipath_devdata *dd,u32 port,int freehdrq) +{ +struct ipath_portdata *pd = dd->ipath_pd[port]; + +if (!pd) +return ; +if (freehdrq) +/* +* only clear and free portdata if we are going to also +* release the hdrq, otherwise we leak the hdrq on each +* open/close cycle +*/ + dd->ipath_pd[port] =NULL ; +if (freehdrq && pd->port_rcvhdrq) { +ipath_cdbg (VERBOSE ,"free closed port %d rcvhdrq @ %p " +"(size=%lu)\n" , pd->port_port, pd->port_rcvhdrq, + (unsigned long ) pd->port_rcvhdrq_size); +dma_free_coherent (&dd->pcidev->dev, pd->port_rcvhdrq_size, + pd->port_rcvhdrq, pd->port_rcvhdrq_phys); + pd->port_rcvhdrq =NULL ; + } +if (port && pd->port_rcvegrbuf) { +/* always free this */ +if (pd->port_rcvegrbuf) { +unsigned e; + +for (e =0 ; e < pd->port_rcvegrbuf_chunks; e++) { +void *base = pd->port_rcvegrbuf[e]; +size_t size = pd->port_rcvegrbuf_size; + +ipath_cdbg (VERBOSE ,"egrbuf free(%p, %lu), " +"chunk %u/%u\n" , base, + (unsigned long ) size, + e, pd->port_rcvegrbuf_chunks); +dma_free_coherent ( + &dd->pcidev->dev, size, base, + pd->port_rcvegrbuf_phys[e]); + } +vfree (pd->port_rcvegrbuf); + pd->port_rcvegrbuf =NULL ; +vfree (pd->port_rcvegrbuf_phys); + pd->port_rcvegrbuf_phys =NULL ; + } + pd->port_rcvegrbuf_chunks =0 ; + }else if (port ==0 && dd->ipath_port0_skbs) { +unsigned e; +struct sk_buff **skbs = dd->ipath_port0_skbs; + + dd->ipath_port0_skbs =NULL ; +ipath_cdbg (VERBOSE ,"free closed port %d ipath_port0_skbs " +"@ %p\n" , pd->port_port, skbs); +for (e =0 ; e < dd->ipath_rcvegrcnt; e++) +if (skbs[e]) +dev_kfree_skb (skbs[e]); +vfree (skbs); + } +if (freehdrq) { +kfree (pd->port_tid_pg_list); +kfree (pd); + } +} + +int __init infinipath_init (void ) +{ +int ret; + + ipath_dbg(KERN_INFO DRIVER_LOAD_MSG "%s", ipath_core_version); + +/* +* These must be called before the driver is registered with +* the PCI subsystem. + */ + idr_init(&unit_table); +if (!idr_pre_get (&unit_table,GFP_KERNEL )) { + ret = -ENOMEM ; + goto bail; + } + + ret =pci_register_driver (&ipath_driver); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME + ": Unable to register driver: error %d\n", -ret); + goto bail_unit; + } + + ret =ipath_driver_create_group (&ipath_driver.driver); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME ": Unable to create driver " + "sysfs entries: error %d\n", -ret); + goto bail_pci; + } + + ret =ipath_init_ipathfs (); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME ": Unable to create " + "ipathfs: error %d\n", -ret); + goto bail_group; + } + + goto bail; + +bail_group: +ipath_driver_remove_group (&ipath_driver.driver); + +bail_pci: +pci_unregister_driver (&ipath_driver); + +bail_unit: +idr_destroy (&unit_table); + +bail: +return ret; +} + +static void cleanup_device (struct ipath_devdata *dd) +{ +int port; + +ipath_shutdown_device (dd); + +if (*dd->ipath_statusp &IPATH_STATUS_CHIP_PRESENT ) { +/* can't do anything more with chip; needs re-init */ + *dd->ipath_statusp &= ~IPATH_STATUS_CHIP_PRESENT ; +if (dd->ipath_kregbase) { +/* +* if we haven't already cleaned up before these are +* to ensure any register reads/writes "fail" until +* re-init +*/ + dd->ipath_kregbase =NULL ; + dd->ipath_kregvirt =NULL ; + dd->ipath_uregbase =0 ; + dd->ipath_sregbase =0 ; + dd->ipath_cregbase =0 ; + dd->ipath_kregsize =0 ; + } +ipath_disable_wc (dd); + } + +if (dd->ipath_pioavailregs_dma) { +dma_free_coherent (&dd->pcidev->dev,PAGE_SIZE , + (void *) dd->ipath_pioavailregs_dma, + dd->ipath_pioavailregs_phys); + dd->ipath_pioavailregs_dma =NULL ; + } + +if (dd->ipath_pageshadow) { +struct page **tmpp = dd->ipath_pageshadow; +int i, cnt =0 ; + +ipath_cdbg (VERBOSE ,"Unlocking any expTID pages still " +"locked\n" ); +for (port =0 ; port < dd->ipath_cfgports; port++) { +int port_tidbase = port * dd->ipath_rcvtidcnt; +int maxtid = port_tidbase + dd->ipath_rcvtidcnt; +for (i = port_tidbase; i < maxtid; i++) { +if (!tmpp[i]) +continue ; +ipath_release_user_pages (&tmpp[i],1 ); + tmpp[i] =NULL ; + cnt++; + } + } +if (cnt) { + ipath_stats.sps_pageunlocks += cnt; +ipath_cdbg (VERBOSE ,"There were still %u expTID " +"entries locked\n" , cnt); + } +if (ipath_stats.sps_pagelocks || + ipath_stats.sps_pageunlocks) +ipath_cdbg (VERBOSE ,"%llu pages locked, %llu " +"unlocked via ipath_m{un}lock\n" , + (unsigned long long ) + ipath_stats.sps_pagelocks, + (unsigned long long ) + ipath_stats.sps_pageunlocks); + +ipath_cdbg (VERBOSE ,"Free shadow page tid array at %p\n" , + dd->ipath_pageshadow); +vfree (dd->ipath_pageshadow); + dd->ipath_pageshadow =NULL ; + } + +/* +* free any resources still in use (usually just kernel ports) +* at unload +*/ +for (port =0 ; port < dd->ipath_cfgports; port++) +ipath_free_pddata (dd, port,1 ); +kfree (dd->ipath_pd); +/* +* debuggability, in case some cleanup path tries to use it +* after this +*/ + dd->ipath_pd =NULL ; +} + +static void __exit infinipath_cleanup(void) +{ +struct ipath_devdata *dd, *tmp; +unsigned long flags; + +ipath_exit_ipathfs (); + +ipath_driver_remove_group (&ipath_driver.driver); + +spin_lock_irqsave (&ipath_devs_lock, flags); + +/* +* turn off rcv, send, and interrupts for all ports, all drivers +* should also hard reset the chip here? +* free up port 0 (kernel) rcvhdr, egr bufs, and eventually tid bufs +* for all versions of the driver, if they were allocated +*/ +list_for_each_entry_safe (dd, tmp, &ipath_dev_list, ipath_list) { +spin_unlock_irqrestore (&ipath_devs_lock, flags); + +if (dd->ipath_kregbase) +cleanup_device (dd); + +if (dd->pcidev) { +if (dd->pcidev->irq) { +ipath_cdbg (VERBOSE , +"unit %u free_irq of irq %x\n" , + dd->ipath_unit, dd->pcidev->irq); +free_irq (dd->pcidev->irq, dd); + }else +ipath_dbg ("irq is 0, not doing free_irq " +"for unit %u\n" , dd->ipath_unit); + dd->pcidev =NULL ; + } + +/* +* we check for NULL here, because it's outside the kregbase +* check, and we need to call it after the free_irq. Thus +* it's possible that the function pointers were never +* initialized. +*/ +if (dd->ipath_f_cleanup) +/* clean up chip-specific stuff */ + dd->ipath_f_cleanup (dd); + +spin_lock_irqsave (&ipath_devs_lock, flags); + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + +ipath_cdbg (VERBOSE ,"Unregistering pci driver\n" ); +pci_unregister_driver (&ipath_driver); + +idr_destroy (&unit_table); +} + +/** +* ipath_reset_device - reset the chip if possible +* @unit: the device to reset +* +* Whether or not reset is successful, we attempt to re-initialize the chip +* (that is, much like a driver unload/reload). We clear the INITTED flag +* so that the various entry points will fail until we reinitialize. For +* now, we only allow this if no user ports are open that use chip resources +*/ +int ipath_reset_device (int unit) +{ +int ret, i; +struct ipath_devdata *dd =ipath_lookup (unit); + +if (!dd) { + ret = -ENODEV ; + goto bail; + } + +dev_info (&dd->pcidev->dev,"Reset on unit %u requested\n" , unit); + +if (!dd->ipath_kregbase || !(dd->ipath_flags &IPATH_PRESENT )) { +dev_info (&dd->pcidev->dev,"Invalid unit number %u or " +"not initialized or not present\n" , unit); + ret = -ENXIO ; + goto bail; + } + +if (dd->ipath_pd) +for (i =1 ; i < dd->ipath_portcnt; i++) { +if (dd->ipath_pd[i] && dd->ipath_pd[i]->port_cnt) { +ipath_dbg ("unit %u port %d is in use " +"(PID %u cmd %s), can't reset\n" , + unit, i, + dd->ipath_pd[i]->port_pid, + dd->ipath_pd[i]->port_comm); + ret = -EBUSY ; + goto bail; + } + } + + dd->ipath_flags &= ~IPATH_INITTED ; + ret = dd->ipath_f_reset (dd); +if (ret !=1 ) +ipath_dbg ("reset was not successful\n" ); +ipath_dbg ("Trying to reinitialize unit %u after reset attempt\n" , + unit); + ret =ipath_init_chip (dd,1 ); +if (ret) +ipath_dev_err (dd,"Reinitialize unit %u after " +"reset failed with %d\n" , unit, ret); +else +dev_info (&dd->pcidev->dev,"Reinitialized unit %u after " +"resetting\n" , unit); + +bail: +return ret; +} + +module_init (infinipath_init); +module_exit (infinipath_cleanup);
PATCH 1/1 ipath - misc driver support code
In reply to Bryan O'SullivanEEPROM support, interrupt handling, statistics gathering, and write combining management for x86_64.
A note regarding i2c: The Atmel EEPROM hardware we use looks like an i2c device electrically, but is not i2c compliant at all from a functional perspective. We tried using the kernel's i2c support to talk to it, but failed.
Normal i2c devices have a single 7-bit or 10-bit i2c address that they respond to. Valid 7-bit addresses range from 0x03 to 0x77. Addresses 0x00 to 0x02 and 0x78 to 0x7F are special reserved addresses (e.g. 0x00 is the "general call" address.) The Atmel device, on the other hand, responds to ALL addresses. It's designed to be the only device on a given i2c bus. A given i2c device address corresponds to the memory address within the i2c device itself.
At least one reason why the linux core i2c stuff won't work for this is that it prohibits access to reserved addresses like 0x00, which are really valid addresses on the Atmel devices.
drivers/infiniband/hw/ipath/ipath_eeprom.c new file +613 -0
@@ -0,0 +1,613 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/vmalloc.h> + +#include "ipath_kernel.h" + +/* +* InfiniPath I2C driver for a serial eeprom. This is not a generic +* I2C interface. For a start, the device we're using (Atmel AT24C11) +* doesn't work like a regular I2C device. It looks like one +* electrically, but not logically. Normal I2C devices have a single +* 7-bit or 10-bit I2C address that they respond to. Valid 7-bit +* addresses range from 0x03 to 0x77. Addresses 0x00 to 0x02 and 0x78 +* to 0x7F are special reserved addresses (e.g. 0x00 is the "general +* call" address.) The Atmel device, on the other hand, responds to ALL +* 7-bit addresses. It's designed to be the only device on a given I2C +* bus. A 7-bit address corresponds to the memory address within the +* Atmel device itself. +* +* Also, the timing requirements mean more than simple software +* bitbanging, with readbacks from chip to ensure timing (simple udelay +* is not enough). +* +* This all means that accessing the device is specialized enough +* that using the standard kernel I2C bitbanging interface would be +* impossible. For example, the core I2C eeprom driver expects to find +* a device at one or more of a limited set of addresses only. It doesn't +* allow writing to an eeprom. It also doesn't provide any means of +* accessing eeprom contents from within the kernel, only via sysfs. +*/ + +enum i2c_type { + i2c_line_scl =0 , + i2c_line_sda +}; + +enum i2c_state { + i2c_line_low =0 , + i2c_line_high +}; + +#define READ_CMD 1 +#define WRITE_CMD 0 + +static int eeprom_init; + +/* +* The gpioval manipulation really should be protected by spinlocks +* or be converted to use atomic operations. +*/ + +/** +* i2c_gpio_set - set a GPIO line +* @dd: the infinipath device +* @line: the line to set +* @new_line_state: the state to set +* +* Returns 0 if the line was set to the new state successfully, non-zero +* on error. +*/ +static int i2c_gpio_set (struct ipath_devdata *dd, +enum i2c_type line, +enum i2c_state new_line_state) +{ +u64 read_val, write_val, mask, *gpioval; + + gpioval = &dd->ipath_gpio_out; + read_val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_extctrl); +if (line == i2c_line_scl) + mask = ipath_gpio_scl; +else + mask = ipath_gpio_sda; + +if (new_line_state == i2c_line_high) +/* tri-state the output rather than force high */ + write_val = read_val & ~mask; +else +/* config line to be an output */ + write_val = read_val | mask; +ipath_write_kreg (dd, dd->ipath_kregs->kr_extctrl, write_val); + +/* set high and verify */ +if (new_line_state == i2c_line_high) + write_val =0x1UL ; +else + write_val =0x0UL ; + +if (line == i2c_line_scl) { + write_val <<= ipath_gpio_scl_num; + *gpioval = *gpioval & ~(1UL << ipath_gpio_scl_num); + *gpioval |= write_val; + }else { + write_val <<= ipath_gpio_sda_num; + *gpioval = *gpioval & ~(1UL << ipath_gpio_sda_num); + *gpioval |= write_val; + } +ipath_write_kreg (dd, dd->ipath_kregs->kr_gpio_out, *gpioval); + +return 0 ; +} + +/** +* i2c_gpio_get - get a GPIO line state +* @dd: the infinipath device +* @line: the line to get +* @curr_statep: where to put the line state +* +* Returns 0 if the line was set to the new state successfully, non-zero +* on error. curr_state is not set on error. +*/ +static int i2c_gpio_get (struct ipath_devdata *dd, +enum i2c_type line, +enum i2c_state *curr_statep) +{ +u64 read_val, write_val, mask; +int ret; + +/* check args */ +if (curr_statep ==NULL ) { + ret =1 ; + goto bail; + } + + read_val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_extctrl); +/* config line to be an input */ +if (line == i2c_line_scl) + mask = ipath_gpio_scl; +else + mask = ipath_gpio_sda; + write_val = read_val & ~mask; +ipath_write_kreg (dd, dd->ipath_kregs->kr_extctrl, write_val); + read_val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_extstatus); + +if (read_val & mask) + *curr_statep = i2c_line_high; +else + *curr_statep = i2c_line_low; + + ret =0 ; + +bail: +return ret; +} + +/** +* i2c_wait_for_writes - wait for a write +* @dd: the infinipath device +* +* We use this instead of udelay directly, so we can make sure +* that previous register writes have been flushed all the way +* to the chip. Since we are delaying anyway, the cost doesn't +* hurt, and makes the bit twiddling more regular +*/ +static void i2c_wait_for_writes (struct ipath_devdata *dd) +{ + (void )ipath_read_kreg32 (dd, dd->ipath_kregs->kr_scratch); +} + +static void scl_out (struct ipath_devdata *dd,u8 bit) +{ +i2c_gpio_set (dd, i2c_line_scl, bit ? i2c_line_high : i2c_line_low); + +i2c_wait_for_writes (dd); +} + +static void sda_out (struct ipath_devdata *dd,u8 bit) +{ +i2c_gpio_set (dd, i2c_line_sda, bit ? i2c_line_high : i2c_line_low); + +i2c_wait_for_writes (dd); +} + +static u8 sda_in (struct ipath_devdata *dd,int wait) +{ +enum i2c_state bit; + +if (i2c_gpio_get (dd, i2c_line_sda, &bit)) +ipath_dbg ("get bit failed!\n" ); + +if (wait) +i2c_wait_for_writes (dd); + +return bit == i2c_line_high ?1U :0 ; +} + +/** +* i2c_ackrcv - see if ack following write is true +* @dd: the infinipath device +*/ +static int i2c_ackrcv (struct ipath_devdata *dd) +{ +u8 ack_received; + +/* AT ENTRY SCL = LOW */ +/* change direction, ignore data */ + ack_received =sda_in (dd,1 ); +scl_out (dd, i2c_line_high); + ack_received =sda_in (dd,1 ) ==0 ; +scl_out (dd, i2c_line_low); +return ack_received; +} + +/** +* wr_byte - write a byte, one bit at a time +* @dd: the infinipath device +* @data: the byte to write +* +* Returns 0 if we got the following ack, otherwise 1 +*/ +static int wr_byte (struct ipath_devdata *dd,u8 data) +{ +int bit_cntr; +u8 bit; + +for (bit_cntr =7 ; bit_cntr >=0 ; bit_cntr--) { + bit = (data >> bit_cntr) &1 ; +sda_out (dd, bit); +scl_out (dd, i2c_line_high); +scl_out (dd, i2c_line_low); + } +return (!i2c_ackrcv (dd)) ?1 :0 ; +} + +static void send_ack (struct ipath_devdata *dd) +{ +sda_out (dd, i2c_line_low); +scl_out (dd, i2c_line_high); +scl_out (dd, i2c_line_low); +sda_out (dd, i2c_line_high); +} + +/** +* i2c_startcmd - transmit the start condition, followed by address/cmd +* @dd: the infinipath device +* @offset_dir: direction byte +* +* (both clock/data high, clock high, data low while clock is high) +*/ +static int i2c_startcmd (struct ipath_devdata *dd,u8 offset_dir) +{ +int res; + +/* issue start sequence */ +sda_out (dd, i2c_line_high); +scl_out (dd, i2c_line_high); +sda_out (dd, i2c_line_low); +scl_out (dd, i2c_line_low); + +/* issue length and direction byte */ + res =wr_byte (dd, offset_dir); + +if (res) +ipath_cdbg (VERBOSE ,"No ack to complete start\n" ); + +return res; +} + +/** +* stop_cmd - transmit the stop condition +* @dd: the infinipath device +* +* (both clock/data low, clock high, data high while clock is high) +*/ +static void stop_cmd (struct ipath_devdata *dd) +{ +scl_out (dd, i2c_line_low); +sda_out (dd, i2c_line_low); +scl_out (dd, i2c_line_high); +sda_out (dd, i2c_line_high); +udelay (2 ); +} + +/** +* eeprom_reset - reset I2C communication +* @dd: the infinipath device +*/ + +static int eeprom_reset (struct ipath_devdata *dd) +{ +int clock_cycles_left =9 ; +u64 *gpioval = &dd->ipath_gpio_out; +int ret; + + eeprom_init =1 ; + *gpioval =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_gpio_out); +ipath_cdbg (VERBOSE ,"Resetting i2c eeprom; initial gpioout reg " +"is %llx\n" , (unsigned long long ) *gpioval); + +/* +* This is to get the i2c into a known state, by first going low, +* then tristate sda (and then tristate scl as first thing +* in loop) +*/ +scl_out (dd, i2c_line_low); +sda_out (dd, i2c_line_high); + +while (clock_cycles_left--) { +scl_out (dd, i2c_line_high); + +if (sda_in (dd,0 )) { +sda_out (dd, i2c_line_low); +scl_out (dd, i2c_line_low); + ret =0 ; + goto bail; + } + +scl_out (dd, i2c_line_low); + } + + ret =1 ; + +bail: +return ret; +} + +/** +* ipath_eeprom_read - receives bytes from the eeprom via I2C +* @dd: the infinipath device +* @eeprom_offset: address to read from +* @buffer: where to store result +* @len: number of bytes to receive +*/ + +int ipath_eeprom_read (struct ipath_devdata *dd,u8 eeprom_offset, +void *buffer,int len) +{ +/* compiler complains unless initialized */ +u8 single_byte =0 ; +int bit_cntr; +int ret; + +if (!eeprom_init) +eeprom_reset (dd); + + eeprom_offset = (eeprom_offset <<1 ) |READ_CMD ; + +if (i2c_startcmd (dd, eeprom_offset)) { +ipath_dbg ("Failed startcmd\n" ); +stop_cmd (dd); + ret =1 ; + goto bail; + } + +/* +* eeprom keeps clocking data out as long as we ack, automatically +* incrementing the address. +*/ +while (len-- >0 ) { +/* get data */ + single_byte =0 ; +for (bit_cntr =8 ; bit_cntr; bit_cntr--) { +u8 bit; +scl_out (dd, i2c_line_high); + bit =sda_in (dd,0 ); + single_byte |= bit << (bit_cntr -1 ); +scl_out (dd, i2c_line_low); + } + +/* send ack if not the last byte */ +if (len) +send_ack (dd); + + *((u8 *) buffer) = single_byte; + buffer++; + } + +stop_cmd (dd); + + ret =0 ; + +bail: +return ret; +} + +/** +* ipath_eeprom_write - writes data to the eeprom via I2C +* @dd: the infinipath device +* @eeprom_offset: where to place data +* @buffer: data to write +* @len: number of bytes to write +*/ +int ipath_eeprom_write (struct ipath_devdata *dd,u8 eeprom_offset, +const void *buffer,int len) +{ +u8 single_byte; +int sub_len; +const u8 *bp = buffer; +int max_wait_time, i; +int ret; + +if (!eeprom_init) +eeprom_reset (dd); + +while (len >0 ) { +if (i2c_startcmd (dd, (eeprom_offset <<1 ) |WRITE_CMD )) { +ipath_dbg ("Failed to start cmd offset %u\n" , + eeprom_offset); + goto failed_write; + } + + sub_len =min (len,4 ); + eeprom_offset += sub_len; + len -= sub_len; + +for (i =0 ; i < sub_len; i++) { +if (wr_byte (dd, *bp++)) { +ipath_dbg ("no ack after byte %u/%u (%u " +"total remain)\n" , i, sub_len, + len + sub_len - i); + goto failed_write; + } + } + +stop_cmd (dd); + +/* +* wait for write complete by waiting for a successful +* read (the chip replies with a zero after the write +* cmd completes, and before it writes to the eeprom. +* The startcmd for the read will fail the ack until +* the writes have completed. We do this inline to avoid +* the debug prints that are in the real read routine +* if the startcmd fails. +*/ + max_wait_time =100 ; +while (i2c_startcmd (dd,READ_CMD )) { +stop_cmd (dd); +if (!--max_wait_time) { +ipath_dbg ("Did not get successful read to " +"complete write\n" ); + goto failed_write; + } + } +/* now read the zero byte */ +for (i = single_byte =0 ; i <8 ; i++) { +u8 bit; +scl_out (dd, i2c_line_high); + bit =sda_in (dd,0 ); +scl_out (dd, i2c_line_low); + single_byte <<=1 ; + single_byte |= bit; + } +stop_cmd (dd); + } + + ret =0 ; + goto bail; + +failed_write: +stop_cmd (dd); + ret =1 ; + +bail: +return ret; +} + +static u8 flash_csum (struct ipath_flash *ifp,int adjust) +{ +u8 *ip = (u8 *) ifp; +u8 csum =0 , len; + +for (len =0 ; len < ifp->if_length; len++) + csum += *ip++; + csum -= ifp->if_csum; + csum = ~csum; +if (adjust) + ifp->if_csum = csum; + +return csum; +} + +/** +* ipath_get_guid - get the GUID from the i2c device +* @dd: the infinipath device +* +* When we add the multi-chip support, we will probably have to add +* the ability to use the number of guids field, and get the guid from +* the first chip's flash, to use for all of them. +*/ +void ipath_get_guid (struct ipath_devdata *dd) +{ +void *buf; +struct ipath_flash *ifp; +__be64 guid; +int len; +u8 csum, *bguid; +int t = dd->ipath_unit; +struct ipath_devdata *dd0 =ipath_lookup (0 ); + +if (t && dd0->ipath_nguid >1 && t <= dd0->ipath_nguid) { +u8 *bguid, oguid; + dd->ipath_guid = dd0->ipath_guid; + bguid = (u8 *) & dd->ipath_guid; + + oguid = bguid[7 ]; + bguid[7 ] += t; +if (oguid > bguid[7 ]) { +if (bguid[6 ] ==0xff ) { +if (bguid[5 ] ==0xff ) { +ipath_dev_err ( + dd, +"Can't set %s GUID from " +"base, wraps to OUI!\n" , +ipath_get_unit_name (t)); + dd->ipath_guid =0 ; + goto bail; + } + bguid[5 ]++; + } + bguid[6 ]++; + } + dd->ipath_nguid =1 ; + +ipath_dbg ("nguid %u, so adding %u to device 0 guid, " +"for %llx\n" , + dd0->ipath_nguid, t, + (unsigned long long )be64_to_cpu (dd->ipath_guid)); + goto bail; + } + + len = offsetof(struct ipath_flash , if_future); + buf =vmalloc (len); +if (!buf) { +ipath_dev_err (dd,"Couldn't allocate memory to read %u " +"bytes from eeprom for GUID\n" , len); + goto bail; + } + +if (ipath_eeprom_read (dd,0 , buf, len)) { +ipath_dev_err (dd,"Failed reading GUID from eeprom\n" ); + goto done; + } + ifp = (struct ipath_flash *)buf; + + csum =flash_csum (ifp,0 ); +if (csum != ifp->if_csum) { +dev_info (&dd->pcidev->dev,"Bad I2C flash checksum: " +"0x%x, not 0x%x\n" , csum, ifp->if_csum); + goto done; + } +if (*(__be64 *) ifp->if_guid ==0ULL || + *(__be64 *) ifp->if_guid ==__constant_cpu_to_be64 (-1LL )) { +ipath_dev_err (dd,"Invalid GUID %llx from flash; " +"ignoring\n" , + *(unsigned long long *) ifp->if_guid); +/* don't allow GUID if all 0 or all 1's */ + goto done; + } + +/* complain, but allow it */ +if (*(u64 *) ifp->if_guid ==0x100007511000000ULL ) +dev_info (&dd->pcidev->dev,"Warning, GUID %llx is " +"default, probably not correct!\n" , + *(unsigned long long *) ifp->if_guid); + + bguid = ifp->if_guid; +if (!bguid[0 ] && !bguid[1 ] && !bguid[2 ]) { +/* original incorrect GUID format in flash; fix in +* core copy, by shifting up 2 octets; don't need to +* change top octet, since both it and shifted are +* 0.. */ + bguid[1 ] = bguid[3 ]; + bguid[2 ] = bguid[4 ]; + bguid[3 ] = bguid[4 ] =0 ; + guid = *(__be64 *) ifp->if_guid; +ipath_cdbg (VERBOSE ,"Old GUID format in flash, top 3 zero, " +"shifting 2 octets\n" ); + }else + guid = *(__be64 *) ifp->if_guid; + dd->ipath_guid = guid; + dd->ipath_nguid = ifp->if_numguid; +memcpy (dd->ipath_serial, ifp->if_serial, +sizeof (ifp->if_serial)); +ipath_cdbg (VERBOSE ,"Initted GUID to %llx from eeprom\n" , + (unsigned long long )be64_to_cpu (dd->ipath_guid)); + +done: +vfree (buf); + +bail:; +}
drivers/infiniband/hw/ipath/ipath_intr.c new file +841 -0
841 lines not on this page · raw message
drivers/infiniband/hw/ipath/ipath_stats.c new file +303 -0
303 lines not on this page · raw message
drivers/infiniband/hw/ipath/ipath_wc_x86_64.c new file +157 -0
157 lines not on this page · raw message
PATCH 1/1 ipath - support for PCI Express devices
In reply to Bryan O'SullivanThis file contains routines and definitions specific to InfiniPath devices that have PCI Express interfaces.
drivers/infiniband/hw/ipath/ipath_pe800.c new file +1247 -0
@@ -0,0 +1,1247 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ +/* +* This file contains all of the code that is specific to the +* InfiniPath PE-800 chip. +*/ + +#include <linux/interrupt.h> +#include <linux/pci.h> +#include <linux/delay.h> + + +#include "ipath_kernel.h" +#include "ipath_registers.h" + +/* +* This file contains all the chip-specific register information and +* access functions for the PathScale PE800, the PCI-Express chip. +* +* This lists the InfiniPath PE800 registers, in the actual chip layout. +* This structure should never be directly accessed. +*/ +struct _infinipath_do_not_use_kernel_regs { +unsigned long long Revision; +unsigned long long Control; +unsigned long long PageAlign; +unsigned long long PortCnt; +unsigned long long DebugPortSelect; +unsigned long long Reserved0; +unsigned long long SendRegBase; +unsigned long long UserRegBase; +unsigned long long CounterRegBase; +unsigned long long Scratch; +unsigned long long Reserved1; +unsigned long long Reserved2; +unsigned long long IntBlocked; +unsigned long long IntMask; +unsigned long long IntStatus; +unsigned long long IntClear; +unsigned long long ErrorMask; +unsigned long long ErrorStatus; +unsigned long long ErrorClear; +unsigned long long HwErrMask; +unsigned long long HwErrStatus; +unsigned long long HwErrClear; +unsigned long long HwDiagCtrl; +unsigned long long MDIO; +unsigned long long IBCStatus; +unsigned long long IBCCtrl; +unsigned long long ExtStatus; +unsigned long long ExtCtrl; +unsigned long long GPIOOut; +unsigned long long GPIOMask; +unsigned long long GPIOStatus; +unsigned long long GPIOClear; +unsigned long long RcvCtrl; +unsigned long long RcvBTHQP; +unsigned long long RcvHdrSize; +unsigned long long RcvHdrCnt; +unsigned long long RcvHdrEntSize; +unsigned long long RcvTIDBase; +unsigned long long RcvTIDCnt; +unsigned long long RcvEgrBase; +unsigned long long RcvEgrCnt; +unsigned long long RcvBufBase; +unsigned long long RcvBufSize; +unsigned long long RxIntMemBase; +unsigned long long RxIntMemSize; +unsigned long long RcvPartitionKey; +unsigned long long Reserved3; +unsigned long long RcvPktLEDCnt; +unsigned long long Reserved4[8 ]; +unsigned long long SendCtrl; +unsigned long long SendPIOBufBase; +unsigned long long SendPIOSize; +unsigned long long SendPIOBufCnt; +unsigned long long SendPIOAvailAddr; +unsigned long long TxIntMemBase; +unsigned long long TxIntMemSize; +unsigned long long Reserved5; +unsigned long long PCIeRBufTestReg0; +unsigned long long PCIeRBufTestReg1; +unsigned long long Reserved51[6 ]; +unsigned long long SendBufferError; +unsigned long long SendBufferErrorCONT1; +unsigned long long Reserved6SBE[6 ]; +unsigned long long RcvHdrAddr0; +unsigned long long RcvHdrAddr1; +unsigned long long RcvHdrAddr2; +unsigned long long RcvHdrAddr3; +unsigned long long RcvHdrAddr4; +unsigned long long Reserved7RHA[11 ]; +unsigned long long RcvHdrTailAddr0; +unsigned long long RcvHdrTailAddr1; +unsigned long long RcvHdrTailAddr2; +unsigned long long RcvHdrTailAddr3; +unsigned long long RcvHdrTailAddr4; +unsigned long long Reserved8RHTA[11 ]; +unsigned long long Reserved9SW[8 ]; +unsigned long long SerdesConfig0; +unsigned long long SerdesConfig1; +unsigned long long SerdesStatus; +unsigned long long XGXSConfig; +unsigned long long IBPLLCfg; +unsigned long long Reserved10SW2[3 ]; +unsigned long long PCIEQ0SerdesConfig0; +unsigned long long PCIEQ0SerdesConfig1; +unsigned long long PCIEQ0SerdesStatus; +unsigned long long Reserved11; +unsigned long long PCIEQ1SerdesConfig0; +unsigned long long PCIEQ1SerdesConfig1; +unsigned long long PCIEQ1SerdesStatus; +unsigned long long Reserved12; +}; + +#define IPATH_KREG_OFFSET (field) (offsetof(struct \ + _infinipath_do_not_use_kernel_regs, field) / sizeof(u64)) +#define IPATH_CREG_OFFSET (field) (offsetof( \ + struct infinipath_counters, field) / sizeof(u64)) + +static const struct ipath_kregs ipath_pe_kregs = { + .kr_control =IPATH_KREG_OFFSET (Control), + .kr_counterregbase =IPATH_KREG_OFFSET (CounterRegBase), + .kr_debugportselect =IPATH_KREG_OFFSET (DebugPortSelect), + .kr_errorclear =IPATH_KREG_OFFSET (ErrorClear), + .kr_errormask =IPATH_KREG_OFFSET (ErrorMask), + .kr_errorstatus =IPATH_KREG_OFFSET (ErrorStatus), + .kr_extctrl =IPATH_KREG_OFFSET (ExtCtrl), + .kr_extstatus =IPATH_KREG_OFFSET (ExtStatus), + .kr_gpio_clear =IPATH_KREG_OFFSET (GPIOClear), + .kr_gpio_mask =IPATH_KREG_OFFSET (GPIOMask), + .kr_gpio_out =IPATH_KREG_OFFSET (GPIOOut), + .kr_gpio_status =IPATH_KREG_OFFSET (GPIOStatus), + .kr_hwdiagctrl =IPATH_KREG_OFFSET (HwDiagCtrl), + .kr_hwerrclear =IPATH_KREG_OFFSET (HwErrClear), + .kr_hwerrmask =IPATH_KREG_OFFSET (HwErrMask), + .kr_hwerrstatus =IPATH_KREG_OFFSET (HwErrStatus), + .kr_ibcctrl =IPATH_KREG_OFFSET (IBCCtrl), + .kr_ibcstatus =IPATH_KREG_OFFSET (IBCStatus), + .kr_intblocked =IPATH_KREG_OFFSET (IntBlocked), + .kr_intclear =IPATH_KREG_OFFSET (IntClear), + .kr_intmask =IPATH_KREG_OFFSET (IntMask), + .kr_intstatus =IPATH_KREG_OFFSET (IntStatus), + .kr_mdio =IPATH_KREG_OFFSET (MDIO ), + .kr_pagealign =IPATH_KREG_OFFSET (PageAlign), + .kr_partitionkey =IPATH_KREG_OFFSET (RcvPartitionKey), + .kr_portcnt =IPATH_KREG_OFFSET (PortCnt), + .kr_rcvbthqp =IPATH_KREG_OFFSET (RcvBTHQP), + .kr_rcvbufbase =IPATH_KREG_OFFSET (RcvBufBase), + .kr_rcvbufsize =IPATH_KREG_OFFSET (RcvBufSize), + .kr_rcvctrl =IPATH_KREG_OFFSET (RcvCtrl), + .kr_rcvegrbase =IPATH_KREG_OFFSET (RcvEgrBase), + .kr_rcvegrcnt =IPATH_KREG_OFFSET (RcvEgrCnt), + .kr_rcvhdrcnt =IPATH_KREG_OFFSET (RcvHdrCnt), + .kr_rcvhdrentsize =IPATH_KREG_OFFSET (RcvHdrEntSize), + .kr_rcvhdrsize =IPATH_KREG_OFFSET (RcvHdrSize), + .kr_rcvintmembase =IPATH_KREG_OFFSET (RxIntMemBase), + .kr_rcvintmemsize =IPATH_KREG_OFFSET (RxIntMemSize), + .kr_rcvtidbase =IPATH_KREG_OFFSET (RcvTIDBase), + .kr_rcvtidcnt =IPATH_KREG_OFFSET (RcvTIDCnt), + .kr_revision =IPATH_KREG_OFFSET (Revision), + .kr_scratch =IPATH_KREG_OFFSET (Scratch), + .kr_sendbuffererror =IPATH_KREG_OFFSET (SendBufferError), + .kr_sendctrl =IPATH_KREG_OFFSET (SendCtrl), + .kr_sendpioavailaddr =IPATH_KREG_OFFSET (SendPIOAvailAddr), + .kr_sendpiobufbase =IPATH_KREG_OFFSET (SendPIOBufBase), + .kr_sendpiobufcnt =IPATH_KREG_OFFSET (SendPIOBufCnt), + .kr_sendpiosize =IPATH_KREG_OFFSET (SendPIOSize), + .kr_sendregbase =IPATH_KREG_OFFSET (SendRegBase), + .kr_txintmembase =IPATH_KREG_OFFSET (TxIntMemBase), + .kr_txintmemsize =IPATH_KREG_OFFSET (TxIntMemSize), + .kr_userregbase =IPATH_KREG_OFFSET (UserRegBase), + .kr_serdesconfig0 =IPATH_KREG_OFFSET (SerdesConfig0), + .kr_serdesconfig1 =IPATH_KREG_OFFSET (SerdesConfig1), + .kr_serdesstatus =IPATH_KREG_OFFSET (SerdesStatus), + .kr_xgxsconfig =IPATH_KREG_OFFSET (XGXSConfig), + .kr_ibpllcfg =IPATH_KREG_OFFSET (IBPLLCfg), + +/* +* These should not be used directly via ipath_read_kreg64(), +* use them with ipath_read_kreg64_port() +*/ + .kr_rcvhdraddr =IPATH_KREG_OFFSET (RcvHdrAddr0), + .kr_rcvhdrtailaddr =IPATH_KREG_OFFSET (RcvHdrTailAddr0), + +/* This group is pe-800-specific; and used only in this file */ +/* The rcvpktled register controls one of the debug port signals, so +* a packet activity LED can be connected to it. */ + .kr_rcvpktledcnt =IPATH_KREG_OFFSET (RcvPktLEDCnt), + .kr_pcierbuftestreg0 =IPATH_KREG_OFFSET (PCIeRBufTestReg0), + .kr_pcierbuftestreg1 =IPATH_KREG_OFFSET (PCIeRBufTestReg1), + .kr_pcieq0serdesconfig0 =IPATH_KREG_OFFSET (PCIEQ0SerdesConfig0), + .kr_pcieq0serdesconfig1 =IPATH_KREG_OFFSET (PCIEQ0SerdesConfig1), + .kr_pcieq0serdesstatus =IPATH_KREG_OFFSET (PCIEQ0SerdesStatus), + .kr_pcieq1serdesconfig0 =IPATH_KREG_OFFSET (PCIEQ1SerdesConfig0), + .kr_pcieq1serdesconfig1 =IPATH_KREG_OFFSET (PCIEQ1SerdesConfig1), + .kr_pcieq1serdesstatus =IPATH_KREG_OFFSET (PCIEQ1SerdesStatus) +}; + +static const struct ipath_cregs ipath_pe_cregs = { + .cr_badformatcnt =IPATH_CREG_OFFSET (RxBadFormatCnt), + .cr_erricrccnt =IPATH_CREG_OFFSET (RxICRCErrCnt), + .cr_errlinkcnt =IPATH_CREG_OFFSET (RxLinkProblemCnt), + .cr_errlpcrccnt =IPATH_CREG_OFFSET (RxLPCRCErrCnt), + .cr_errpkey =IPATH_CREG_OFFSET (RxPKeyMismatchCnt), + .cr_errrcvflowctrlcnt =IPATH_CREG_OFFSET (RxFlowCtrlErrCnt), + .cr_err_rlencnt =IPATH_CREG_OFFSET (RxLenErrCnt), + .cr_errslencnt =IPATH_CREG_OFFSET (TxLenErrCnt), + .cr_errtidfull =IPATH_CREG_OFFSET (RxTIDFullErrCnt), + .cr_errtidvalid =IPATH_CREG_OFFSET (RxTIDValidErrCnt), + .cr_errvcrccnt =IPATH_CREG_OFFSET (RxVCRCErrCnt), + .cr_ibstatuschange =IPATH_CREG_OFFSET (IBStatusChangeCnt), + .cr_intcnt =IPATH_CREG_OFFSET (LBIntCnt), + .cr_invalidrlencnt =IPATH_CREG_OFFSET (RxMaxMinLenErrCnt), + .cr_invalidslencnt =IPATH_CREG_OFFSET (TxMaxMinLenErrCnt), + .cr_lbflowstallcnt =IPATH_CREG_OFFSET (LBFlowStallCnt), + .cr_pktrcvcnt =IPATH_CREG_OFFSET (RxDataPktCnt), + .cr_pktrcvflowctrlcnt =IPATH_CREG_OFFSET (RxFlowPktCnt), + .cr_pktsendcnt =IPATH_CREG_OFFSET (TxDataPktCnt), + .cr_pktsendflowcnt =IPATH_CREG_OFFSET (TxFlowPktCnt), + .cr_portovflcnt =IPATH_CREG_OFFSET (RxP0HdrEgrOvflCnt), + .cr_rcvebpcnt =IPATH_CREG_OFFSET (RxEBPCnt), + .cr_rcvovflcnt =IPATH_CREG_OFFSET (RxBufOvflCnt), + .cr_senddropped =IPATH_CREG_OFFSET (TxDroppedPktCnt), + .cr_sendstallcnt =IPATH_CREG_OFFSET (TxFlowStallCnt), + .cr_sendunderruncnt =IPATH_CREG_OFFSET (TxUnderrunCnt), + .cr_wordrcvcnt =IPATH_CREG_OFFSET (RxDwordCnt), + .cr_wordsendcnt =IPATH_CREG_OFFSET (TxDwordCnt), + .cr_unsupvlcnt =IPATH_CREG_OFFSET (TxUnsupVLErrCnt), + .cr_rxdroppktcnt =IPATH_CREG_OFFSET (RxDroppedPktCnt), + .cr_iblinkerrrecovcnt =IPATH_CREG_OFFSET (IBLinkErrRecoveryCnt), + .cr_iblinkdowncnt =IPATH_CREG_OFFSET (IBLinkDownedCnt), + .cr_ibsymbolerrcnt =IPATH_CREG_OFFSET (IBSymbolErrCnt) +}; + +/* kr_intstatus, kr_intclear, kr_intmask bits */ +#define INFINIPATH_I_RCVURG_MASK 0x1F +#define INFINIPATH_I_RCVAVAIL_MASK 0x1F + +/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */ +#define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x000000000000003fULL +#define INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT 0 +#define INFINIPATH_HWE_PCIEPOISONEDTLP 0x0000000010000000ULL +#define INFINIPATH_HWE_PCIECPLTIMEOUT 0x0000000020000000ULL +#define INFINIPATH_HWE_PCIEBUSPARITYXTLH 0x0000000040000000ULL +#define INFINIPATH_HWE_PCIEBUSPARITYXADM 0x0000000080000000ULL +#define INFINIPATH_HWE_PCIEBUSPARITYRADM 0x0000000100000000ULL +#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL +#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL +#define INFINIPATH_HWE_PCIE1PLLFAILED 0x0400000000000000ULL +#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL +#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL + +/* kr_extstatus bits */ +#define INFINIPATH_EXTS_FREQSEL 0x2 +#define INFINIPATH_EXTS_SERDESSEL 0x4 +#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000 +#define INFINIPATH_EXTS_MEMBIST_FOUND 0x0000000000008000 + +#define _IPATH_GPIO_SDA_NUM 1 +#define _IPATH_GPIO_SCL_NUM 0 + +#define IPATH_GPIO_SDA (1ULL << \ + (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) +#define IPATH_GPIO_SCL (1ULL << \ + (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) + +/** +* ipath_pe_handle_hwerrors - display hardware errors. +* @dd: the infinipath device +* @msg: the output buffer +* @msgl: the size of the output buffer +* +* Use same msg buffer as regular errors to avoid excessive stack +* use. Most hardware errors are catastrophic, but for right now, +* we'll print them and continue. We reuse the same message buffer as +* ipath_handle_errors() to avoid excessive stack usage. +*/ +void ipath_pe_handle_hwerrors (struct ipath_devdata *dd,char *msg, +size_t msgl) +{ +ipath_err_t hwerrs; +u32 bits, ctrl; +int isfatal =0 ; +char bitsmsg[64 ]; + + hwerrs =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_hwerrstatus); +if (!hwerrs) { +/* +* better than printing cofusing messages +* This seems to be related to clearing the crc error, or +* the pll error during init. +*/ +ipath_cdbg (VERBOSE ,"Called but no hardware errors set\n" ); +return ; + }else if (hwerrs == ~0ULL ) { +ipath_dev_err (dd,"Read of hardware error status failed " +"(all bits set); ignoring\n" ); +return ; + } + ipath_stats.sps_hwerrs++; + +/* Always clear the error status register, except MEMBISTFAIL, +* regardless of whether we continue or stop using the chip. +* We want that set so we know it failed, even across driver reload. +* We'll still ignore it in the hwerrmask. We do this partly for +* diagnostics, but also for support */ +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrclear, + hwerrs&~INFINIPATH_HWE_MEMBISTFAILED ); + + hwerrs &= dd->ipath_hwerrmask; + +/* +* make sure we get this much out, unless told to be quiet, +* or it's occurred within the last 5 seconds +*/ +if ((hwerrs & ~dd->ipath_lasthwerror) || + (ipath_debug & __IPATH_VERBDBG)) +dev_info (&dd->pcidev->dev,"Hardware error: hwerr=0x%llx " +"(cleared)\n" , (unsigned long long ) hwerrs); + dd->ipath_lasthwerror |= hwerrs; + +if (hwerrs & ~infinipath_hwe_bitsextant) +ipath_dev_err (dd,"hwerror interrupt with unknown errors " +"%llx set\n" , (unsigned long long ) + (hwerrs & ~infinipath_hwe_bitsextant)); + + ctrl =ipath_read_kreg32 (dd, dd->ipath_kregs->kr_control); +if (ctrl &INFINIPATH_C_FREEZEMODE ) { +if (hwerrs) { +/* +* if any set that we aren't ignoring only make the +* complaint once, in case it's stuck or recurring, +* and we get here multiple times +*/ +if (dd->ipath_flags &IPATH_INITTED ) { +ipath_dev_err (dd,"Fatal Error (freeze " +"mode), no longer usable\n" ); + isfatal =1 ; + } +/* +* Mark as having had an error for driver, and also +* for /sys and status word mapped to user programs. +* This marks unit as not usable, until reset +*/ + *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY ; + *dd->ipath_statusp |=IPATH_STATUS_HWERROR ; + dd->ipath_flags &= ~IPATH_INITTED ; + }else { +ipath_dbg ("Clearing freezemode on ignored hardware " +"error\n" ); + ctrl &= ~INFINIPATH_C_FREEZEMODE ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_control, + ctrl); + } + } + + *msg ='\0' ; + +if (hwerrs &INFINIPATH_HWE_MEMBISTFAILED ) { +strlcat (msg,"[Memory BIST test failed, PE-800 unusable]" , + msgl); +/* ignore from now on, so disable until driver reloaded */ + *dd->ipath_statusp |=IPATH_STATUS_HWERROR ; + dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } +if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK + <<INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT )) { + bits = (u32) ((hwerrs >> +INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT ) & +INFINIPATH_HWE_RXEMEMPARITYERR_MASK ); +snprintf (bitsmsg,sizeof bitsmsg,"[RXE Parity Errs %x] " , + bits); +strlcat (msg, bitsmsg, msgl); + } +if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK + <<INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT )) { + bits = (u32) ((hwerrs >> +INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT ) & +INFINIPATH_HWE_TXEMEMPARITYERR_MASK ); +snprintf (bitsmsg,sizeof bitsmsg,"[TXE Parity Errs %x] " , + bits); +strlcat (msg, bitsmsg, msgl); + } +if (hwerrs & (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK + <<INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT )) { + bits = (u32) ((hwerrs >> +INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT ) & +INFINIPATH_HWE_PCIEMEMPARITYERR_MASK ); +snprintf (bitsmsg,sizeof bitsmsg, +"[PCIe Mem Parity Errs %x] " , bits); +strlcat (msg, bitsmsg, msgl); + } +if (hwerrs &INFINIPATH_HWE_IBCBUSTOSPCPARITYERR ) +strlcat (msg,"[IB2IPATH Parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_IBCBUSFRSPCPARITYERR ) +strlcat (msg,"[IPATH2IB Parity]" , msgl); + +#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \ + INFINIPATH_HWE_COREPLL_RFSLIP ) + +if (hwerrs & _IPATH_PLL_FAIL) { +snprintf (bitsmsg,sizeof bitsmsg, +"[PLL failed (%llx), PE-800 unusable]" , + (unsigned long long ) hwerrs & _IPATH_PLL_FAIL); +strlcat (msg, bitsmsg, msgl); +/* ignore from now on, so disable until driver reloaded */ + dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL); +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + +if (hwerrs &INFINIPATH_HWE_SERDESPLLFAILED ) { +/* +* If it occurs, it is left masked since the eternal +* interface is unused +*/ + dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + +if (hwerrs &INFINIPATH_HWE_PCIEPOISONEDTLP ) +strlcat (msg,"[PCIe Poisoned TLP]" , msgl); +if (hwerrs &INFINIPATH_HWE_PCIECPLTIMEOUT ) +strlcat (msg,"[PCIe completion timeout]" , msgl); + +/* +* In practice, it's unlikely wthat we'll see PCIe PLL, or bus +* parity or memory parity error failures, because most likely we +* won't be able to talk to the core of the chip. Nonetheless, we +* might see them, if they are in parts of the PCIe core that aren't +* essential. +*/ +if (hwerrs &INFINIPATH_HWE_PCIE1PLLFAILED ) +strlcat (msg,"[PCIePLL1]" , msgl); +if (hwerrs &INFINIPATH_HWE_PCIE0PLLFAILED ) +strlcat (msg,"[PCIePLL0]" , msgl); +if (hwerrs &INFINIPATH_HWE_PCIEBUSPARITYXTLH ) +strlcat (msg,"[PCIe XTLH core parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_PCIEBUSPARITYXADM ) +strlcat (msg,"[PCIe ADM TX core parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_PCIEBUSPARITYRADM ) +strlcat (msg,"[PCIe ADM RX core parity]" , msgl); + +if (hwerrs &INFINIPATH_HWE_RXDSYNCMEMPARITYERR ) +strlcat (msg,"[Rx Dsync]" , msgl); +if (hwerrs &INFINIPATH_HWE_SERDESPLLFAILED ) +strlcat (msg,"[SerDes PLL]" , msgl); + +ipath_dev_err (dd,"%s hardware error\n" , msg); +if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) { +/* +* for /sys status file ; if no trailing } is copied, we'll +* know it was truncated. +*/ +snprintf (dd->ipath_freezemsg, dd->ipath_freezelen, +"{%s}" , msg); + } +} + +/** +* ipath_pe_boardname - fill in the board name +* @dd: the infinipath device +* @name: the output buffer +* @namelen: the size of the output buffer +* +* info is based on the board revision register +*/ +static int ipath_pe_boardname (struct ipath_devdata *dd,char *name, +size_t namelen) +{ +char *n =NULL ; +u8 boardrev = dd->ipath_boardrev; +int ret; + +switch (boardrev) { +case 0 : + n ="InfiniPath_Emulation" ; +break ; +case 1 : + n ="InfiniPath_PE-800-Bringup" ; +break ; +case 2 : + n ="InfiniPath_PE-880" ; +break ; +case 3 : + n ="InfiniPath_PE-850" ; +break ; +case 4 : + n ="InfiniPath_PE-860" ; +break ; +default : +ipath_dev_err (dd, +"Don't yet know about board with ID %u\n" , + boardrev); +snprintf (name, namelen,"Unknown_InfiniPath_PE-8xx_%u" , + boardrev); +break ; + } +if (n) +snprintf (name, namelen,"%s" , n); + +if (dd->ipath_majrev !=4 || dd->ipath_minrev !=1 ) { +ipath_dev_err (dd,"Unsupported PE-800 revision %u.%u!\n" , + dd->ipath_majrev, dd->ipath_minrev); + ret =1 ; + }else + ret =0 ; + +return ret; +} + +/** +* ipath_pe_init_hwerrors - enable hardware errors +* @dd: the infinipath device +* +* now that we have finished initializing everything that might reasonably +* cause a hardware error, and cleared those errors bits as they occur, +* we can enable hardware errors in the mask (potentially enabling +* freeze mode), and enable hardware errors as errors (along with +* everything else) in errormask +*/ +void ipath_pe_init_hwerrors (struct ipath_devdata *dd) +{ +ipath_err_t val; +u64 extsval; + + extsval =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_extstatus); + +if (!(extsval &INFINIPATH_EXTS_MEMBIST_ENDTEST )) +ipath_dev_err (dd,"MemBIST did not complete!\n" ); + + val = ~0ULL ;/* barring bugs, all hwerrors become interrupts, */ + +if (!dd->ipath_boardrev)// no PLL for Emulator + val &= ~INFINIPATH_HWE_SERDESPLLFAILED ; + +/* workaround bug 9460 in internal interface bus parity checking */ + val &= ~INFINIPATH_HWE_PCIEBUSPARITYRADM ; + + dd->ipath_hwerrmask = val; +} + +/** +* ipath_pe_bringup_serdes - bring up the serdes +* @dd: the infinipath device +*/ +int ipath_pe_bringup_serdes (struct ipath_devdata *dd) +{ +u64 val, tmp, config1; +int ret =0 , change =0 ; + +ipath_dbg ("Trying to bringup serdes\n" ); + +if (ipath_read_kreg64 (dd, dd->ipath_kregs->kr_hwerrstatus) & +INFINIPATH_HWE_SERDESPLLFAILED ) { +ipath_dbg ("At start, serdes PLL failed bit set " +"in hwerrstatus, clearing and continuing\n" ); +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrclear, +INFINIPATH_HWE_SERDESPLLFAILED ); + } + + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig0); + config1 =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig1); + +ipath_cdbg (VERBOSE ,"SerDes status config0=%llx config1=%llx, " +"xgxsconfig %llx\n" , (unsigned long long ) val, + (unsigned long long ) config1, (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_xgxsconfig)); + +/* +* Force reset on, also set rxdetect enable. Must do before reading +* serdesstatus at least for simulation, or some of the bits in +* serdes status will come back as undefined and cause simulation +* failures +*/ + val |=INFINIPATH_SERDC0_RESET_PLL |INFINIPATH_SERDC0_RXDETECT_EN + |INFINIPATH_SERDC0_L1PWR_DN ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, val); +/* be sure chip saw it */ + tmp =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); +udelay (5 );/* need pll reset set at least for a bit */ +/* +* after PLL is reset, set the per-lane Resets and TxIdle and +* clear the PLL reset and rxdetect (to get falling edge). +* Leave L1PWR bits set (permanently) +*/ + val &= ~(INFINIPATH_SERDC0_RXDETECT_EN |INFINIPATH_SERDC0_RESET_PLL + |INFINIPATH_SERDC0_L1PWR_DN ); + val |=INFINIPATH_SERDC0_RESET_MASK |INFINIPATH_SERDC0_TXIDLE ; +ipath_cdbg (VERBOSE ,"Clearing pll reset and setting lane resets " +"and txidle (%llx)\n" , (unsigned long long ) val); +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, val); +/* be sure chip saw it */ + tmp =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); +/* need PLL reset clear for at least 11 usec before lane +* resets cleared; give it a few more to be sure */ +udelay (15 ); + val &= ~(INFINIPATH_SERDC0_RESET_MASK |INFINIPATH_SERDC0_TXIDLE ); + +ipath_cdbg (VERBOSE ,"Clearing lane resets and txidle " +"(writing %llx)\n" , (unsigned long long ) val); +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, val); +/* be sure chip saw it */ + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); + + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_xgxsconfig); +if (((val >>INFINIPATH_XGXS_MDIOADDR_SHIFT ) & +INFINIPATH_XGXS_MDIOADDR_MASK ) !=3 ) { + val &= + ~(INFINIPATH_XGXS_MDIOADDR_MASK << +INFINIPATH_XGXS_MDIOADDR_SHIFT ); +/* MDIO address 3 */ + val |=3ULL <<INFINIPATH_XGXS_MDIOADDR_SHIFT ; + change =1 ; + } +if (val &INFINIPATH_XGXS_RESET ) { + val &= ~INFINIPATH_XGXS_RESET ; + change =1 ; + } +if (change) +ipath_write_kreg (dd, dd->ipath_kregs->kr_xgxsconfig, val); + + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig0); + +/* clear current and de-emphasis bits */ + config1 &= ~0x0ffffffff00ULL ; +/* set current to 20ma */ + config1 |=0x00000000000ULL ; +/* set de-emphasis to -5.68dB */ + config1 |=0x0cccc000000ULL ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig1, config1); + +ipath_cdbg (VERBOSE ,"done: SerDes status config0=%llx " +"config1=%llx, sstatus=%llx xgxs=%llx\n" , + (unsigned long long ) val, (unsigned long long ) config1, + (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesstatus), + (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_xgxsconfig)); + +if (!ipath_waitfor_mdio_cmdready (dd)) { +ipath_write_kreg ( + dd, dd->ipath_kregs->kr_mdio, +ipath_mdio_req (IPATH_MDIO_CMD_READ ,31 , +IPATH_MDIO_CTRL_XGXS_REG_8 ,0 )); +if (ipath_waitfor_complete (dd, dd->ipath_kregs->kr_mdio, +IPATH_MDIO_DATAVALID , &val)) +ipath_dbg ("Never got MDIO data for XGXS " +"status read\n" ); +else +ipath_cdbg (VERBOSE ,"MDIO Read reg8, " +"'bank' 31 %x\n" , (u32 ) val); + }else +ipath_dbg ("Never got MDIO cmdready for XGXS status read\n" ); + +return ret; +} + +/** +* ipath_pe_quiet_serdes - set serdes to txidle +* @dd: the infinipath device +* Called when driver is being unloaded +*/ +void ipath_pe_quiet_serdes (struct ipath_devdata *dd) +{ +u64 val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig0); + + val |=INFINIPATH_SERDC0_TXIDLE ; +ipath_dbg ("Setting TxIdleEn on serdes (config0 = %llx)\n" , + (unsigned long long ) val); +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, val); +} + +/* this is not yet needed on the PE800, so just return 0. */ +static int ipath_pe_intconfig (struct ipath_devdata *dd) +{ +return 0 ; +} + +/** +* ipath_setup_pe_setextled - set the state of the two external LEDs +* @dd: the infinipath device +* @lst: the L state +* @ltst: the LT state + +* These LEDs indicate the physical and logical state of IB link. +* For this chip (at least with recommended board pinouts), LED1 +* is Yellow (logical state) and LED2 is Green (physical state), +* +* Note: We try to match the Mellanox HCA LED behavior as best +* we can. Green indicates physical link state is OK (something is +* plugged in, and we can train). +* Amber indicates the link is logically up (ACTIVE). +* Mellanox further blinks the amber LED to indicate data packet +* activity, but we have no hardware support for that, so it would +* require waking up every 10-20 msecs and checking the counters +* on the chip, and then turning the LED off if appropriate. That's +* visible overhead, so not something we will do. +* +*/ +static void ipath_setup_pe_setextled (struct ipath_devdata *dd,u64 lst, +u64 ltst) +{ +u64 extctl; + +/* the diags use the LED to indicate diag info, so we leave +* the external LED alone when the diags are running */ +if (ipath_diag_inuse) +return ; + + extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON | +INFINIPATH_EXTC_LED2PRIPORT_ON ); + +if (ltst &INFINIPATH_IBCS_LT_STATE_LINKUP ) + extctl |=INFINIPATH_EXTC_LED2PRIPORT_ON ; +if (lst ==INFINIPATH_IBCS_L_STATE_ACTIVE ) + extctl |=INFINIPATH_EXTC_LED1PRIPORT_ON ; + dd->ipath_extctrl = extctl; +ipath_write_kreg (dd, dd->ipath_kregs->kr_extctrl, extctl); +} + +/** +* ipath_setup_pe_cleanup - clean up any per-chip chip-specific stuff +* @dd: the infinipath device +* +* This is called during driver unload. +* We do the pci_disable_msi here, not in generic code, because it +* isn't used for the HT-400. If we do end up needing pci_enable_msi +* at some point in the future for HT-400, we'll move the call back +* into the main init_one code. +*/ +static void ipath_setup_pe_cleanup (struct ipath_devdata *dd) +{ + dd->ipath_msi_lo =0 ;/* just in case unload fails */ +pci_disable_msi (dd->pcidev); +} + +/** +* ipath_setup_pe_config - setup PCIe config related stuff +* @dd: the infinipath device +* @pdev: the PCI device +* +* The pci_enable_msi() call will fail on systems with MSI quirks +* such as those with AMD8131, even if the device of interest is not +* attached to that device, (in the 2.6.13 - 2.6.15 kernels, at least, fixed +* late in 2.6.16). +* All that can be done is to edit the kernel source to remove the quirk +* check until that is fixed. +* We do not need to call enable_msi() for our HyperTransport chip (HT-400), +* even those it uses MSI, and we want to avoid the quirk warning, so +* So we call enable_msi only for the PE-800. If we do end up needing +* pci_enable_msi at some point in the future for HT-400, we'll move the +* call back into the main init_one code. +* We save the msi lo and hi values, so we can restore them after +* chip reset (the kernel PCI infrastructure doesn't yet handle that +* correctly). +*/ +static int ipath_setup_pe_config (struct ipath_devdata *dd, +struct pci_dev *pdev) +{ +int pos, ret; + + dd->ipath_msi_lo =0 ;/* used as a flag during reset processing */ + ret =pci_enable_msi (dd->pcidev); +if (ret) +ipath_dev_err (dd,"pci_enable_msi failed: %d, " +"interrupts may not work\n" , ret); +/* continue even if it fails, we may still be OK... */ + +if ((pos =pci_find_capability (dd->pcidev,PCI_CAP_ID_MSI ))) { +u16 control; +pci_read_config_dword (dd->pcidev, pos +PCI_MSI_ADDRESS_LO , + &dd->ipath_msi_lo); +pci_read_config_dword (dd->pcidev, pos +PCI_MSI_ADDRESS_HI , + &dd->ipath_msi_hi); +pci_read_config_word (dd->pcidev, pos +PCI_MSI_FLAGS , + &control); +/* now save the data (vector) info */ +pci_read_config_word (dd->pcidev, + pos + ((control &PCI_MSI_FLAGS_64BIT ) + ?12 :8 ), + &dd->ipath_msi_data); +ipath_cdbg (VERBOSE ,"Read msi data 0x%x from config offset " +"0x%x, control=0x%x\n" , dd->ipath_msi_data, + pos + ((control &PCI_MSI_FLAGS_64BIT ) ?12 :8 ), + control); +/* we save the cachelinesize also, although it doesn't +* really matter */ +pci_read_config_byte (dd->pcidev,PCI_CACHE_LINE_SIZE , + &dd->ipath_pci_cacheline); + }else +ipath_dev_err (dd,"Can't find MSI capability, " +"can't save MSI settings for reset\n" ); +if ((pos =pci_find_capability (dd->pcidev,PCI_CAP_ID_EXP ))) { +u16 linkstat; +pci_read_config_word (dd->pcidev, pos +PCI_EXP_LNKSTA , + &linkstat); + linkstat >>=4 ; + linkstat &=0x1f ; +if (linkstat !=8 ) +ipath_dev_err (dd,"PCIe width %u, " +"performance reduced\n" , linkstat); + } +else +ipath_dev_err (dd,"Can't find PCI Express " +"capability!\n" ); +return 0 ; +} + +static void ipath_init_pe_variables (void ) +{ +/* +* bits for selecting i2c direction and values, +* used for I2C serial flash +*/ + ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM; + ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM; + ipath_gpio_sda =IPATH_GPIO_SDA ; + ipath_gpio_scl =IPATH_GPIO_SCL ; + +/* variables for sanity checking interrupt and errors */ + infinipath_hwe_bitsextant = + (INFINIPATH_HWE_RXEMEMPARITYERR_MASK << +INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT ) | + (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK << +INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT ) | +INFINIPATH_HWE_PCIE1PLLFAILED | +INFINIPATH_HWE_PCIE0PLLFAILED | +INFINIPATH_HWE_PCIEPOISONEDTLP | +INFINIPATH_HWE_PCIECPLTIMEOUT | +INFINIPATH_HWE_PCIEBUSPARITYXTLH | +INFINIPATH_HWE_PCIEBUSPARITYXADM | +INFINIPATH_HWE_PCIEBUSPARITYRADM | +INFINIPATH_HWE_MEMBISTFAILED | +INFINIPATH_HWE_COREPLL_FBSLIP | +INFINIPATH_HWE_COREPLL_RFSLIP | +INFINIPATH_HWE_SERDESPLLFAILED | +INFINIPATH_HWE_IBCBUSTOSPCPARITYERR | +INFINIPATH_HWE_IBCBUSFRSPCPARITYERR ; + infinipath_i_bitsextant = + (INFINIPATH_I_RCVURG_MASK <<INFINIPATH_I_RCVURG_SHIFT ) | + (INFINIPATH_I_RCVAVAIL_MASK << +INFINIPATH_I_RCVAVAIL_SHIFT ) | +INFINIPATH_I_ERROR |INFINIPATH_I_SPIOSENT | +INFINIPATH_I_SPIOBUFAVAIL |INFINIPATH_I_GPIO ; + infinipath_e_bitsextant = +INFINIPATH_E_RFORMATERR |INFINIPATH_E_RVCRC | +INFINIPATH_E_RICRC |INFINIPATH_E_RMINPKTLEN | +INFINIPATH_E_RMAXPKTLEN |INFINIPATH_E_RLONGPKTLEN | +INFINIPATH_E_RSHORTPKTLEN |INFINIPATH_E_RUNEXPCHAR | +INFINIPATH_E_RUNSUPVL |INFINIPATH_E_REBP | +INFINIPATH_E_RIBFLOW |INFINIPATH_E_RBADVERSION | +INFINIPATH_E_RRCVEGRFULL |INFINIPATH_E_RRCVHDRFULL | +INFINIPATH_E_RBADTID |INFINIPATH_E_RHDRLEN | +INFINIPATH_E_RHDR |INFINIPATH_E_RIBLOSTLINK | +INFINIPATH_E_SMINPKTLEN |INFINIPATH_E_SMAXPKTLEN | +INFINIPATH_E_SUNDERRUN |INFINIPATH_E_SPKTLEN | +INFINIPATH_E_SDROPPEDSMPPKT |INFINIPATH_E_SDROPPEDDATAPKT | +INFINIPATH_E_SPIOARMLAUNCH |INFINIPATH_E_SUNEXPERRPKTNUM | +INFINIPATH_E_SUNSUPVL |INFINIPATH_E_IBSTATUSCHANGED | +INFINIPATH_E_INVALIDADDR |INFINIPATH_E_RESET | +INFINIPATH_E_HARDWARE ; + + infinipath_i_rcvavail_mask =INFINIPATH_I_RCVAVAIL_MASK ; + infinipath_i_rcvurg_mask =INFINIPATH_I_RCVURG_MASK ; +} + +/* setup the MSI stuff again after a reset. I'd like to just call +* pci_enable_msi() and request_irq() again, but when I do that, +* the MSI enable bit doesn't get set in the command word, and +* we switch to to a different interrupt vector, which is confusing, +* so I instead just do it all inline. Perhaps somehow can tie this +* into the PCIe hotplug support at some point +* Note, because I'm doing it all here, I don't call pci_disable_msi() +* or free_irq() at the start of ipath_setup_pe_reset(). +*/ +static int ipath_reinit_msi (struct ipath_devdata *dd) +{ +int pos; +u16 control; +int ret; + +if (!dd->ipath_msi_lo) { +dev_info (&dd->pcidev->dev,"Can't restore MSI config, " +"initial setup failed?\n" ); + ret =0 ; + goto bail; + } + +if (!(pos =pci_find_capability (dd->pcidev,PCI_CAP_ID_MSI ))) { +ipath_dev_err (dd,"Can't find MSI capability, " +"can't restore MSI settings\n" ); + ret =0 ; + goto bail; + } +ipath_cdbg (VERBOSE ,"Writing msi_lo 0x%x to config offset 0x%x\n" , + dd->ipath_msi_lo, pos +PCI_MSI_ADDRESS_LO ); +pci_write_config_dword (dd->pcidev, pos +PCI_MSI_ADDRESS_LO , + dd->ipath_msi_lo); +ipath_cdbg (VERBOSE ,"Writing msi_lo 0x%x to config offset 0x%x\n" , + dd->ipath_msi_hi, pos +PCI_MSI_ADDRESS_HI ); +pci_write_config_dword (dd->pcidev, pos +PCI_MSI_ADDRESS_HI , + dd->ipath_msi_hi); +pci_read_config_word (dd->pcidev, pos +PCI_MSI_FLAGS , &control); +if (!(control &PCI_MSI_FLAGS_ENABLE )) { +ipath_cdbg (VERBOSE ,"MSI control at off %x was %x, " +"setting MSI enable (%x)\n" , pos +PCI_MSI_FLAGS , + control, control |PCI_MSI_FLAGS_ENABLE ); + control |=PCI_MSI_FLAGS_ENABLE ; +pci_write_config_word (dd->pcidev, pos +PCI_MSI_FLAGS , + control); + } +/* now rewrite the data (vector) info */ +pci_write_config_word (dd->pcidev, pos + + ((control &PCI_MSI_FLAGS_64BIT ) ?12 :8 ), + dd->ipath_msi_data); +/* we restore the cachelinesize also, although it doesn't really +* matter */ +pci_write_config_byte (dd->pcidev,PCI_CACHE_LINE_SIZE , + dd->ipath_pci_cacheline); +/* and now set the pci master bit again */ +pci_set_master (dd->pcidev); + ret =1 ; + +bail: +return ret; +} + +/* This routine sleeps, so it can only be called from user context, not +* from interrupt context. If we need interrupt context, we can split +* it into two routines. +*/ +static int ipath_setup_pe_reset (struct ipath_devdata *dd) +{ +u64 val; +int i; +int ret; + +/* Use ERROR so it shows up in logs, etc. */ +ipath_dev_err (dd,"Resetting PE-800 unit %u\n" , + dd->ipath_unit); + val = dd->ipath_control |INFINIPATH_C_RESET ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_control, val); +mb (); + +for (i =1 ; i <=5 ; i++) { +int r; +/* allow MBIST, etc. to complete; longer on each retry. +* We sometimes get machine checks from bus timeout if no +* response, so for now, make it *really* long. +*/ +msleep (1000 + (1 + i) *2000 ); +if ((r = +pci_write_config_dword (dd->pcidev,PCI_BASE_ADDRESS_0 , + dd->ipath_pcibar0))) +ipath_dev_err (dd,"rewrite of BAR0 failed: %d\n" , + r); +if ((r = +pci_write_config_dword (dd->pcidev,PCI_BASE_ADDRESS_1 , + dd->ipath_pcibar1))) +ipath_dev_err (dd,"rewrite of BAR1 failed: %d\n" , + r); +/* now re-enable memory access */ +if ((r =pci_enable_device (dd->pcidev))) +ipath_dev_err (dd,"pci_enable_device failed after " +"reset: %d\n" , r); + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_revision); +if (val == dd->ipath_revision) { +ipath_cdbg (VERBOSE ,"Got matching revision " +"register %llx on try %d\n" , + (unsigned long long ) val, i); + ret =ipath_reinit_msi (dd); + goto bail; + } +/* Probably getting -1 back */ +ipath_dbg ("Didn't get expected revision register, " +"got %llx, try %d\n" , (unsigned long long ) val, + i +1 ); + } + ret =0 ;/* failed */ + +bail: +return ret; +} + +/** +* ipath_pe_put_tid - write a TID in chip +* @dd: the infinipath device +* @tidptr: pointer to the expected TID (in chip) to udpate +* @tidtype: 0 for eager, 1 for expected +* @pa: physical address of in memory buffer; ipath_tidinvalid if freeing +* +* This exists as a separate routine to allow for special locking etc. +* It's used for both the full cleanup on exit, as well as the normal +* setup and teardown. +*/ +static void ipath_pe_put_tid (struct ipath_devdata *dd,u64 __iomem *tidptr, +u32 type,unsigned long pa) +{ +u32 __iomem *tidp32 = (u32 __iomem *)tidptr; +unsigned long flags =0 ;/* keep gcc quiet */ + +if (pa != dd->ipath_tidinvalid) { +if (pa & ((1U <<11 ) -1 )) { +dev_info (&dd->pcidev->dev,"BUG: physaddr %lx " +"not 4KB aligned!\n" , pa); +return ; + } + pa >>=11 ; +/* paranoia check */ +if (pa & (7 <<29 )) +ipath_dev_err (dd, +"BUG: Physical page address 0x%lx " +"has bits set in 31-29\n" , pa); + +if (type ==0 ) + pa |= dd->ipath_tidtemplate; +else /* for now, always full 4KB page */ + pa |=2 <<29 ; + } + +/* workaround chip bug 9437 by writing each TID twice +* and holding a spinlock around the writes, so they don't +* intermix with other TID (eager or expected) writes +* Unfortunately, this call can be done from interrupt level +* for the port 0 eager TIDs, so we have to use irqsave +*/ +spin_lock_irqsave (&dd->ipath_tid_lock, flags); +ipath_write_kreg (dd, dd->ipath_kregs->kr_scratch,0xfeeddeaf ); +if (dd->ipath_kregbase) +writel (pa, tidp32); +ipath_write_kreg (dd, dd->ipath_kregs->kr_scratch,0xdeadbeef ); +mmiowb (); +spin_unlock_irqrestore (&dd->ipath_tid_lock, flags); +} + +/** +* ipath_pe_clear_tid - clear all TID entries for a port, expected and eager +* @dd: the infinipath device +* @port: the port +* +* clear all TID entries for a port, expected and eager. +* Used from ipath_close(). On PE800, TIDs are only 32 bits, +* not 64, but they are still on 64 bit boundaries, so tidbase +* is declared as u64 * for the pointer math, even though we write 32 bits +*/ +static void ipath_pe_clear_tids (struct ipath_devdata *dd,unsigned port) +{ +u64 __iomem *tidbase; +unsigned long tidinv; +int i; + +if (!dd->ipath_kregbase) +return ; + +ipath_cdbg (VERBOSE ,"Invalidate TIDs for port %u\n" , port); + + tidinv = dd->ipath_tidinvalid; + tidbase = (u64 __iomem *) + ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvtidbase + + port * dd->ipath_rcvtidcnt *sizeof (*tidbase)); + +for (i =0 ; i < dd->ipath_rcvtidcnt; i++) +ipath_pe_put_tid (dd, &tidbase[i],0 , tidinv); + + tidbase = (u64 __iomem *) + ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvegrbase + + port * dd->ipath_rcvegrcnt *sizeof (*tidbase)); + +for (i =0 ; i < dd->ipath_rcvegrcnt; i++) +ipath_pe_put_tid (dd, &tidbase[i],1 , tidinv); +} + +/** +* ipath_pe_tidtemplate - setup constants for TID updates +* @dd: the infinipath device +* +* We setup stuff that we use a lot, to avoid calculating each time +*/ +static void ipath_pe_tidtemplate (struct ipath_devdata *dd) +{ +u32 egrsize = dd->ipath_rcvegrbufsize; + +/* For now, we always allocate 4KB buffers (at init) so we can +* receive max size packets. We may want a module parameter to +* specify 2KB or 4KB and/or make be per port instead of per device +* for those who want to reduce memory footprint. Note that the +* ipath_rcvhdrentsize size must be large enough to hold the largest +* IB header (currently 96 bytes) that we expect to handle (plus of +* course the 2 dwords of RHF). +*/ +if (egrsize ==2048 ) + dd->ipath_tidtemplate =1U <<29 ; +else if (egrsize ==4096 ) + dd->ipath_tidtemplate =2U <<29 ; +else { + egrsize =4096 ; +dev_info (&dd->pcidev->dev,"BUG: unsupported egrbufsize " +"%u, using %u\n" , dd->ipath_rcvegrbufsize, + egrsize); + dd->ipath_tidtemplate =2U <<29 ; + } + dd->ipath_tidinvalid =0 ; +} + +static int ipath_pe_early_init (struct ipath_devdata *dd) +{ + dd->ipath_flags |=IPATH_4BYTE_TID ; + +/* +* For openib, we need to be able to handle an IB header of 96 bytes +* or 24 dwords. HT-400 has arbitrary sized receive buffers, so we +* made them the same size as the PIO buffers. The PE-800 does not +* handle arbitrary size buffers, so we need the header large enough +* to handle largest IB header, but still have room for a 2KB MTU +* standard IB packet. +*/ + dd->ipath_rcvhdrentsize =24 ; + dd->ipath_rcvhdrsize =IPATH_DFLT_RCVHDRSIZE ; + +/* For HT-400, we allocate a somewhat overly large eager buffer, +* such that we can guarantee that we can receive the largest packet +* that we can send out. To truly support a 4KB MTU, we need to +* bump this to a larger value. We'll do this when I get around to +* testing 4KB sends on the PE-800, which I have not yet done. +*/ + dd->ipath_rcvegrbufsize =2048 ; +/* +* the min() check here is currently a nop, but it may not always +* be, depending on just how we do ipath_rcvegrbufsize +*/ + dd->ipath_ibmaxlen =min (dd->ipath_piosize2k, + dd->ipath_rcvegrbufsize + + (dd->ipath_rcvhdrentsize <<2 )); + dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen; + +/* +* For PE-800, we can request a receive interrupt for 1 or +* more packets from current offset. For now, we set this +* up for a single packet, to match the HT-400 behavior. +*/ + dd->ipath_rhdrhead_intr_off =1ULL <<32 ; + +return 0 ; +} + +int __attribute__((weak))ipath_unordered_wc (void ) +{ +return 0 ; +} + +/** +* ipath_init_pe_get_base_info - set chip-specific flags for user code +* @dd: the infinipath device +* @kbase: ipath_base_info pointer +* +* We set the PCIE flag because the lower bandwidth on PCIe vs +* HyperTransport can affect some user packet algorithims. +*/ +static int ipath_pe_get_base_info (struct ipath_portdata *pd,void *kbase) +{ +struct ipath_base_info *kinfo = kbase; + +if (ipath_unordered_wc ()) { + kinfo->spi_runtime_flags |=IPATH_RUNTIME_FORCE_WC_ORDER ; +ipath_cdbg (PROC ,"Intel processor, forcing WC order\n" ); + } +else +ipath_cdbg (PROC ,"Not Intel processor, WC ordered\n" ); + + kinfo->spi_runtime_flags |=IPATH_RUNTIME_PCIE ; + +return 0 ; +} + +/** +* ipath_init_pe800_funcs - set up the chip-specific function pointers +* @dd: the infinipath device +* +* This is global, and is called directly at init to set up the +* chip-specific function pointers for later use. +*/ +void ipath_init_pe800_funcs (struct ipath_devdata *dd) +{ + dd->ipath_f_intrsetup = ipath_pe_intconfig; + dd->ipath_f_bus = ipath_setup_pe_config; + dd->ipath_f_reset = ipath_setup_pe_reset; + dd->ipath_f_get_boardname = ipath_pe_boardname; + dd->ipath_f_init_hwerrors = ipath_pe_init_hwerrors; + dd->ipath_f_early_init = ipath_pe_early_init; + dd->ipath_f_handle_hwerrors = ipath_pe_handle_hwerrors; + dd->ipath_f_quiet_serdes = ipath_pe_quiet_serdes; + dd->ipath_f_bringup_serdes = ipath_pe_bringup_serdes; + dd->ipath_f_clear_tids = ipath_pe_clear_tids; + dd->ipath_f_put_tid = ipath_pe_put_tid; + dd->ipath_f_cleanup = ipath_setup_pe_cleanup; + dd->ipath_f_setextled = ipath_setup_pe_setextled; + dd->ipath_f_get_base_info = ipath_pe_get_base_info; + +/* initialize chip-specific variables */ + dd->ipath_f_tidtemplate = ipath_pe_tidtemplate; + +/* +* setup the register offsets, since they are different for each +* chip +*/ + dd->ipath_kregs = &ipath_pe_kregs; + dd->ipath_cregs = &ipath_pe_cregs; + +ipath_init_pe_variables (); +} +
PATCH 1/1 ipath - support for HyperTransport devices
In reply to Bryan O'SullivanThe ipath_ht400.c file contains routines and definitions specific to HyperTransport-based InfiniPath devices.
drivers/infiniband/hw/ipath/ipath_ht400.c new file +1586 -0
@@ -0,0 +1,1586 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +/* +* This file contains all of the code that is specific to the InfiniPath +* HT-400 chip. +*/ + +#include <linux/pci.h> +#include <linux/delay.h> + +#include "ipath_kernel.h" +#include "ipath_registers.h" + +/* +* This lists the InfiniPath HT400 registers, in the actual chip layout. +* This structure should never be directly accessed. +* +* The names are in InterCap form because they're taken straight from +* the chip specification. Since they're only used in this file, they +* don't pollute the rest of the source. +*/ + +struct _infinipath_do_not_use_kernel_regs { +unsigned long long Revision; +unsigned long long Control; +unsigned long long PageAlign; +unsigned long long PortCnt; +unsigned long long DebugPortSelect; +unsigned long long DebugPort; +unsigned long long SendRegBase; +unsigned long long UserRegBase; +unsigned long long CounterRegBase; +unsigned long long Scratch; +unsigned long long ReservedMisc1; +unsigned long long InterruptConfig; +unsigned long long IntBlocked; +unsigned long long IntMask; +unsigned long long IntStatus; +unsigned long long IntClear; +unsigned long long ErrorMask; +unsigned long long ErrorStatus; +unsigned long long ErrorClear; +unsigned long long HwErrMask; +unsigned long long HwErrStatus; +unsigned long long HwErrClear; +unsigned long long HwDiagCtrl; +unsigned long long MDIO; +unsigned long long IBCStatus; +unsigned long long IBCCtrl; +unsigned long long ExtStatus; +unsigned long long ExtCtrl; +unsigned long long GPIOOut; +unsigned long long GPIOMask; +unsigned long long GPIOStatus; +unsigned long long GPIOClear; +unsigned long long RcvCtrl; +unsigned long long RcvBTHQP; +unsigned long long RcvHdrSize; +unsigned long long RcvHdrCnt; +unsigned long long RcvHdrEntSize; +unsigned long long RcvTIDBase; +unsigned long long RcvTIDCnt; +unsigned long long RcvEgrBase; +unsigned long long RcvEgrCnt; +unsigned long long RcvBufBase; +unsigned long long RcvBufSize; +unsigned long long RxIntMemBase; +unsigned long long RxIntMemSize; +unsigned long long RcvPartitionKey; +unsigned long long ReservedRcv[10 ]; +unsigned long long SendCtrl; +unsigned long long SendPIOBufBase; +unsigned long long SendPIOSize; +unsigned long long SendPIOBufCnt; +unsigned long long SendPIOAvailAddr; +unsigned long long TxIntMemBase; +unsigned long long TxIntMemSize; +unsigned long long ReservedSend[9 ]; +unsigned long long SendBufferError; +unsigned long long SendBufferErrorCONT1; +unsigned long long SendBufferErrorCONT2; +unsigned long long SendBufferErrorCONT3; +unsigned long long ReservedSBE[4 ]; +unsigned long long RcvHdrAddr0; +unsigned long long RcvHdrAddr1; +unsigned long long RcvHdrAddr2; +unsigned long long RcvHdrAddr3; +unsigned long long RcvHdrAddr4; +unsigned long long RcvHdrAddr5; +unsigned long long RcvHdrAddr6; +unsigned long long RcvHdrAddr7; +unsigned long long RcvHdrAddr8; +unsigned long long ReservedRHA[7 ]; +unsigned long long RcvHdrTailAddr0; +unsigned long long RcvHdrTailAddr1; +unsigned long long RcvHdrTailAddr2; +unsigned long long RcvHdrTailAddr3; +unsigned long long RcvHdrTailAddr4; +unsigned long long RcvHdrTailAddr5; +unsigned long long RcvHdrTailAddr6; +unsigned long long RcvHdrTailAddr7; +unsigned long long RcvHdrTailAddr8; +unsigned long long ReservedRHTA[7 ]; +unsigned long long Sync;/* Software only */ +unsigned long long Dump;/* Software only */ +unsigned long long SimVer;/* Software only */ +unsigned long long ReservedSW[5 ]; +unsigned long long SerdesConfig0; +unsigned long long SerdesConfig1; +unsigned long long SerdesStatus; +unsigned long long XGXSConfig; +unsigned long long ReservedSW2[4 ]; +}; + +#define IPATH_KREG_OFFSET (field) (offsetof(struct \ + _infinipath_do_not_use_kernel_regs, field) / sizeof(u64)) +#define IPATH_CREG_OFFSET (field) (offsetof( \ + struct infinipath_counters, field) / sizeof(u64)) + +static const struct ipath_kregs ipath_ht_kregs = { + .kr_control =IPATH_KREG_OFFSET (Control), + .kr_counterregbase =IPATH_KREG_OFFSET (CounterRegBase), + .kr_debugport =IPATH_KREG_OFFSET (DebugPort), + .kr_debugportselect =IPATH_KREG_OFFSET (DebugPortSelect), + .kr_errorclear =IPATH_KREG_OFFSET (ErrorClear), + .kr_errormask =IPATH_KREG_OFFSET (ErrorMask), + .kr_errorstatus =IPATH_KREG_OFFSET (ErrorStatus), + .kr_extctrl =IPATH_KREG_OFFSET (ExtCtrl), + .kr_extstatus =IPATH_KREG_OFFSET (ExtStatus), + .kr_gpio_clear =IPATH_KREG_OFFSET (GPIOClear), + .kr_gpio_mask =IPATH_KREG_OFFSET (GPIOMask), + .kr_gpio_out =IPATH_KREG_OFFSET (GPIOOut), + .kr_gpio_status =IPATH_KREG_OFFSET (GPIOStatus), + .kr_hwdiagctrl =IPATH_KREG_OFFSET (HwDiagCtrl), + .kr_hwerrclear =IPATH_KREG_OFFSET (HwErrClear), + .kr_hwerrmask =IPATH_KREG_OFFSET (HwErrMask), + .kr_hwerrstatus =IPATH_KREG_OFFSET (HwErrStatus), + .kr_ibcctrl =IPATH_KREG_OFFSET (IBCCtrl), + .kr_ibcstatus =IPATH_KREG_OFFSET (IBCStatus), + .kr_intblocked =IPATH_KREG_OFFSET (IntBlocked), + .kr_intclear =IPATH_KREG_OFFSET (IntClear), + .kr_interruptconfig =IPATH_KREG_OFFSET (InterruptConfig), + .kr_intmask =IPATH_KREG_OFFSET (IntMask), + .kr_intstatus =IPATH_KREG_OFFSET (IntStatus), + .kr_mdio =IPATH_KREG_OFFSET (MDIO ), + .kr_pagealign =IPATH_KREG_OFFSET (PageAlign), + .kr_partitionkey =IPATH_KREG_OFFSET (RcvPartitionKey), + .kr_portcnt =IPATH_KREG_OFFSET (PortCnt), + .kr_rcvbthqp =IPATH_KREG_OFFSET (RcvBTHQP), + .kr_rcvbufbase =IPATH_KREG_OFFSET (RcvBufBase), + .kr_rcvbufsize =IPATH_KREG_OFFSET (RcvBufSize), + .kr_rcvctrl =IPATH_KREG_OFFSET (RcvCtrl), + .kr_rcvegrbase =IPATH_KREG_OFFSET (RcvEgrBase), + .kr_rcvegrcnt =IPATH_KREG_OFFSET (RcvEgrCnt), + .kr_rcvhdrcnt =IPATH_KREG_OFFSET (RcvHdrCnt), + .kr_rcvhdrentsize =IPATH_KREG_OFFSET (RcvHdrEntSize), + .kr_rcvhdrsize =IPATH_KREG_OFFSET (RcvHdrSize), + .kr_rcvintmembase =IPATH_KREG_OFFSET (RxIntMemBase), + .kr_rcvintmemsize =IPATH_KREG_OFFSET (RxIntMemSize), + .kr_rcvtidbase =IPATH_KREG_OFFSET (RcvTIDBase), + .kr_rcvtidcnt =IPATH_KREG_OFFSET (RcvTIDCnt), + .kr_revision =IPATH_KREG_OFFSET (Revision), + .kr_scratch =IPATH_KREG_OFFSET (Scratch), + .kr_sendbuffererror =IPATH_KREG_OFFSET (SendBufferError), + .kr_sendctrl =IPATH_KREG_OFFSET (SendCtrl), + .kr_sendpioavailaddr =IPATH_KREG_OFFSET (SendPIOAvailAddr), + .kr_sendpiobufbase =IPATH_KREG_OFFSET (SendPIOBufBase), + .kr_sendpiobufcnt =IPATH_KREG_OFFSET (SendPIOBufCnt), + .kr_sendpiosize =IPATH_KREG_OFFSET (SendPIOSize), + .kr_sendregbase =IPATH_KREG_OFFSET (SendRegBase), + .kr_txintmembase =IPATH_KREG_OFFSET (TxIntMemBase), + .kr_txintmemsize =IPATH_KREG_OFFSET (TxIntMemSize), + .kr_userregbase =IPATH_KREG_OFFSET (UserRegBase), + .kr_serdesconfig0 =IPATH_KREG_OFFSET (SerdesConfig0), + .kr_serdesconfig1 =IPATH_KREG_OFFSET (SerdesConfig1), + .kr_serdesstatus =IPATH_KREG_OFFSET (SerdesStatus), + .kr_xgxsconfig =IPATH_KREG_OFFSET (XGXSConfig), +/* +* These should not be used directly via ipath_read_kreg64(), +* use them with ipath_read_kreg64_port(), +*/ + .kr_rcvhdraddr =IPATH_KREG_OFFSET (RcvHdrAddr0), + .kr_rcvhdrtailaddr =IPATH_KREG_OFFSET (RcvHdrTailAddr0) +}; + +static const struct ipath_cregs ipath_ht_cregs = { + .cr_badformatcnt =IPATH_CREG_OFFSET (RxBadFormatCnt), + .cr_erricrccnt =IPATH_CREG_OFFSET (RxICRCErrCnt), + .cr_errlinkcnt =IPATH_CREG_OFFSET (RxLinkProblemCnt), + .cr_errlpcrccnt =IPATH_CREG_OFFSET (RxLPCRCErrCnt), + .cr_errpkey =IPATH_CREG_OFFSET (RxPKeyMismatchCnt), + .cr_errrcvflowctrlcnt =IPATH_CREG_OFFSET (RxFlowCtrlErrCnt), + .cr_err_rlencnt =IPATH_CREG_OFFSET (RxLenErrCnt), + .cr_errslencnt =IPATH_CREG_OFFSET (TxLenErrCnt), + .cr_errtidfull =IPATH_CREG_OFFSET (RxTIDFullErrCnt), + .cr_errtidvalid =IPATH_CREG_OFFSET (RxTIDValidErrCnt), + .cr_errvcrccnt =IPATH_CREG_OFFSET (RxVCRCErrCnt), + .cr_ibstatuschange =IPATH_CREG_OFFSET (IBStatusChangeCnt), +/* calc from Reg_CounterRegBase + offset */ + .cr_intcnt =IPATH_CREG_OFFSET (LBIntCnt), + .cr_invalidrlencnt =IPATH_CREG_OFFSET (RxMaxMinLenErrCnt), + .cr_invalidslencnt =IPATH_CREG_OFFSET (TxMaxMinLenErrCnt), + .cr_lbflowstallcnt =IPATH_CREG_OFFSET (LBFlowStallCnt), + .cr_pktrcvcnt =IPATH_CREG_OFFSET (RxDataPktCnt), + .cr_pktrcvflowctrlcnt =IPATH_CREG_OFFSET (RxFlowPktCnt), + .cr_pktsendcnt =IPATH_CREG_OFFSET (TxDataPktCnt), + .cr_pktsendflowcnt =IPATH_CREG_OFFSET (TxFlowPktCnt), + .cr_portovflcnt =IPATH_CREG_OFFSET (RxP0HdrEgrOvflCnt), + .cr_rcvebpcnt =IPATH_CREG_OFFSET (RxEBPCnt), + .cr_rcvovflcnt =IPATH_CREG_OFFSET (RxBufOvflCnt), + .cr_senddropped =IPATH_CREG_OFFSET (TxDroppedPktCnt), + .cr_sendstallcnt =IPATH_CREG_OFFSET (TxFlowStallCnt), + .cr_sendunderruncnt =IPATH_CREG_OFFSET (TxUnderrunCnt), + .cr_wordrcvcnt =IPATH_CREG_OFFSET (RxDwordCnt), + .cr_wordsendcnt =IPATH_CREG_OFFSET (TxDwordCnt), + .cr_unsupvlcnt =IPATH_CREG_OFFSET (TxUnsupVLErrCnt), + .cr_rxdroppktcnt =IPATH_CREG_OFFSET (RxDroppedPktCnt), + .cr_iblinkerrrecovcnt =IPATH_CREG_OFFSET (IBLinkErrRecoveryCnt), + .cr_iblinkdowncnt =IPATH_CREG_OFFSET (IBLinkDownedCnt), + .cr_ibsymbolerrcnt =IPATH_CREG_OFFSET (IBSymbolErrCnt) +}; + +/* kr_intstatus, kr_intclear, kr_intmask bits */ +#define INFINIPATH_I_RCVURG_MASK 0x1FF +#define INFINIPATH_I_RCVAVAIL_MASK 0x1FF + +/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */ +#define INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT 0 +#define INFINIPATH_HWE_HTCMEMPARITYERR_MASK 0x3FFFFFULL +#define INFINIPATH_HWE_HTCLNKABYTE0CRCERR 0x0000000000800000ULL +#define INFINIPATH_HWE_HTCLNKABYTE1CRCERR 0x0000000001000000ULL +#define INFINIPATH_HWE_HTCLNKBBYTE0CRCERR 0x0000000002000000ULL +#define INFINIPATH_HWE_HTCLNKBBYTE1CRCERR 0x0000000004000000ULL +#define INFINIPATH_HWE_HTCMISCERR4 0x0000000008000000ULL +#define INFINIPATH_HWE_HTCMISCERR5 0x0000000010000000ULL +#define INFINIPATH_HWE_HTCMISCERR6 0x0000000020000000ULL +#define INFINIPATH_HWE_HTCMISCERR7 0x0000000040000000ULL +#define INFINIPATH_HWE_HTCBUSTREQPARITYERR 0x0000000080000000ULL +#define INFINIPATH_HWE_HTCBUSTRESPPARITYERR 0x0000000100000000ULL +#define INFINIPATH_HWE_HTCBUSIREQPARITYERR 0x0000000200000000ULL +#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL +#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL +#define INFINIPATH_HWE_HTBPLL_FBSLIP 0x0200000000000000ULL +#define INFINIPATH_HWE_HTBPLL_RFSLIP 0x0400000000000000ULL +#define INFINIPATH_HWE_HTAPLL_FBSLIP 0x0800000000000000ULL +#define INFINIPATH_HWE_HTAPLL_RFSLIP 0x1000000000000000ULL +#define INFINIPATH_HWE_SERDESPLLFAILED 0x2000000000000000ULL + +/* kr_extstatus bits */ +#define INFINIPATH_EXTS_FREQSEL 0x2 +#define INFINIPATH_EXTS_SERDESSEL 0x4 +#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000 +#define INFINIPATH_EXTS_MEMBIST_CORRECT 0x0000000000008000 + +/* +* masks and bits that are different in different chips, or present only +* in one +*/ +static const ipath_err_t infinipath_hwe_htcmemparityerr_mask = +INFINIPATH_HWE_HTCMEMPARITYERR_MASK ; +static const ipath_err_t infinipath_hwe_htcmemparityerr_shift = +INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT ; + +static const ipath_err_t infinipath_hwe_htclnkabyte0crcerr = +INFINIPATH_HWE_HTCLNKABYTE0CRCERR ; +static const ipath_err_t infinipath_hwe_htclnkabyte1crcerr = +INFINIPATH_HWE_HTCLNKABYTE1CRCERR ; +static const ipath_err_t infinipath_hwe_htclnkbbyte0crcerr = +INFINIPATH_HWE_HTCLNKBBYTE0CRCERR ; +static const ipath_err_t infinipath_hwe_htclnkbbyte1crcerr = +INFINIPATH_HWE_HTCLNKBBYTE1CRCERR ; + +#define _IPATH_GPIO_SDA_NUM 1 +#define _IPATH_GPIO_SCL_NUM 0 + +#define IPATH_GPIO_SDA \ + (1ULL << (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) +#define IPATH_GPIO_SCL \ + (1ULL << (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) + +/* keep the code below somewhat more readonable; not used elsewhere */ +#define _IPATH_HTLINK0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \ + infinipath_hwe_htclnkabyte1crcerr) +#define _IPATH_HTLINK1_CRCBITS (infinipath_hwe_htclnkbbyte0crcerr | \ + infinipath_hwe_htclnkbbyte1crcerr) +#define _IPATH_HTLANE0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \ + infinipath_hwe_htclnkbbyte0crcerr) +#define _IPATH_HTLANE1_CRCBITS (infinipath_hwe_htclnkabyte1crcerr | \ + infinipath_hwe_htclnkbbyte1crcerr) + +static void hwerr_crcbits (struct ipath_devdata *dd,ipath_err_t hwerrs, +char *msg,size_t msgl) +{ +char bitsmsg[64 ]; +ipath_err_t crcbits = hwerrs & + (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS); +/* don't check if 8bit HT */ +if (dd->ipath_flags &IPATH_8BIT_IN_HT0 ) + crcbits &= ~infinipath_hwe_htclnkabyte1crcerr; +/* don't check if 8bit HT */ +if (dd->ipath_flags &IPATH_8BIT_IN_HT1 ) + crcbits &= ~infinipath_hwe_htclnkbbyte1crcerr; +/* +* we'll want to ignore link errors on link that is +* not in use, if any. For now, complain about both +*/ +if (crcbits) { +u16 ctrl0, ctrl1; +snprintf (bitsmsg,sizeof bitsmsg, +"[HT%s lane %s CRC (%llx); ignore till reload]" , + !(crcbits & _IPATH_HTLINK1_CRCBITS) ? +"0 (A)" : (!(crcbits & _IPATH_HTLINK0_CRCBITS) + ?"1 (B)" :"0+1 (A+B)" ), + !(crcbits & _IPATH_HTLANE1_CRCBITS) ?"0" + : (!(crcbits & _IPATH_HTLANE0_CRCBITS) ?"1" : +"0+1" ), (unsigned long long ) crcbits); +strlcat (msg, bitsmsg, msgl); + +/* +* print extra info for debugging. slave/primary +* config word 4, 8 (link control 0, 1) +*/ + +if (pci_read_config_word (dd->pcidev, + dd->ipath_ht_slave_off +0x4 , + &ctrl0)) +dev_info (&dd->pcidev->dev,"Couldn't read " +"linkctrl0 of slave/primary " +"config block\n" ); +else if (!(ctrl0 &1 <<6 )) +/* not if EOC bit set */ +ipath_dbg ("HT linkctrl0 0x%x%s%s\n" , ctrl0, + ((ctrl0 >>8 ) &7 ) ?" CRC" :"" , + ((ctrl0 >>4 ) &1 ) ?"linkfail" : +"" ); +if (pci_read_config_word (dd->pcidev, + dd->ipath_ht_slave_off +0x8 , + &ctrl1)) +dev_info (&dd->pcidev->dev,"Couldn't read " +"linkctrl1 of slave/primary " +"config block\n" ); +else if (!(ctrl1 &1 <<6 )) +/* not if EOC bit set */ +ipath_dbg ("HT linkctrl1 0x%x%s%s\n" , ctrl1, + ((ctrl1 >>8 ) &7 ) ?" CRC" :"" , + ((ctrl1 >>4 ) &1 ) ?"linkfail" : +"" ); + +/* disable until driver reloaded */ + dd->ipath_hwerrmask &= ~crcbits; +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); +ipath_dbg ("HT crc errs: %s\n" , msg); + }else +ipath_dbg ("ignoring HT crc errors 0x%llx, " +"not in use\n" , (unsigned long long ) + (hwerrs & (_IPATH_HTLINK0_CRCBITS | + _IPATH_HTLINK1_CRCBITS))); +} + +/** +* ipath_ht_handle_hwerrors - display hardware errors +* @dd: the infinipath device +* @msg: the output buffer +* @msgl: the size of the output buffer +* +* Use same msg buffer as regular errors to avoid +* excessive stack use. Most hardware errors are catastrophic, but for +* right now, we'll print them and continue. +* We reuse the same message buffer as ipath_handle_errors() to avoid +* excessive stack usage. +*/ +static void ipath_ht_handle_hwerrors (struct ipath_devdata *dd,char *msg, +size_t msgl) +{ +ipath_err_t hwerrs; +u32 bits, ctrl; +int isfatal =0 ; +char bitsmsg[64 ]; + + hwerrs =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_hwerrstatus); + +if (!hwerrs) { +ipath_cdbg (VERBOSE ,"Called but no hardware errors set\n" ); +/* +* better than printing cofusing messages +* This seems to be related to clearing the crc error, or +* the pll error during init. +*/ + goto bail; + }else if (hwerrs ==-1LL ) { +ipath_dev_err (dd,"Read of hardware error status failed " +"(all bits set); ignoring\n" ); + goto bail; + } + ipath_stats.sps_hwerrs++; + +/* Always clear the error status register, except MEMBISTFAIL, +* regardless of whether we continue or stop using the chip. +* We want that set so we know it failed, even across driver reload. +* We'll still ignore it in the hwerrmask. We do this partly for +* diagnostics, but also for support */ +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrclear, + hwerrs&~INFINIPATH_HWE_MEMBISTFAILED ); + + hwerrs &= dd->ipath_hwerrmask; + +/* +* make sure we get this much out, unless told to be quiet, +* or it's occurred within the last 5 seconds +*/ +if ((hwerrs & ~dd->ipath_lasthwerror) || + (ipath_debug & __IPATH_VERBDBG)) +dev_info (&dd->pcidev->dev,"Hardware error: hwerr=0x%llx " +"(cleared)\n" , (unsigned long long ) hwerrs); + dd->ipath_lasthwerror |= hwerrs; + +if (hwerrs & ~infinipath_hwe_bitsextant) +ipath_dev_err (dd,"hwerror interrupt with unknown errors " +"%llx set\n" , (unsigned long long ) + (hwerrs & ~infinipath_hwe_bitsextant)); + + ctrl =ipath_read_kreg32 (dd, dd->ipath_kregs->kr_control); +if (ctrl &INFINIPATH_C_FREEZEMODE ) { +if (hwerrs) { +/* +* if any set that we aren't ignoring; only +* make the complaint once, in case it's stuck +* or recurring, and we get here multiple +* times. +*/ +if (dd->ipath_flags &IPATH_INITTED ) { +ipath_dev_err (dd,"Fatal Error (freeze " +"mode), no longer usable\n" ); + isfatal =1 ; + } + *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY ; +/* mark as having had error */ + *dd->ipath_statusp |=IPATH_STATUS_HWERROR ; +/* +* mark as not usable, at a minimum until driver +* is reloaded, probably until reboot, since no +* other reset is possible. +*/ + dd->ipath_flags &= ~IPATH_INITTED ; + }else { +ipath_dbg ("Clearing freezemode on ignored hardware " +"error\n" ); + ctrl &= ~INFINIPATH_C_FREEZEMODE ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_control, + ctrl); + } + } + + *msg ='\0' ; + +/* +* may someday want to decode into which bits are which +* functional area for parity errors, etc. +*/ +if (hwerrs & (infinipath_hwe_htcmemparityerr_mask + <<INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT )) { + bits = (u32) ((hwerrs >> +INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT ) & +INFINIPATH_HWE_HTCMEMPARITYERR_MASK ); +snprintf (bitsmsg,sizeof bitsmsg,"[HTC Parity Errs %x] " , + bits); +strlcat (msg, bitsmsg, msgl); + } +if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK + <<INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT )) { + bits = (u32) ((hwerrs >> +INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT ) & +INFINIPATH_HWE_RXEMEMPARITYERR_MASK ); +snprintf (bitsmsg,sizeof bitsmsg,"[RXE Parity Errs %x] " , + bits); +strlcat (msg, bitsmsg, msgl); + } +if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK + <<INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT )) { + bits = (u32) ((hwerrs >> +INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT ) & +INFINIPATH_HWE_TXEMEMPARITYERR_MASK ); +snprintf (bitsmsg,sizeof bitsmsg,"[TXE Parity Errs %x] " , + bits); +strlcat (msg, bitsmsg, msgl); + } +if (hwerrs &INFINIPATH_HWE_IBCBUSTOSPCPARITYERR ) +strlcat (msg,"[IB2IPATH Parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_IBCBUSFRSPCPARITYERR ) +strlcat (msg,"[IPATH2IB Parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_HTCBUSIREQPARITYERR ) +strlcat (msg,"[HTC Ireq Parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_HTCBUSTREQPARITYERR ) +strlcat (msg,"[HTC Treq Parity]" , msgl); +if (hwerrs &INFINIPATH_HWE_HTCBUSTRESPPARITYERR ) +strlcat (msg,"[HTC Tresp Parity]" , msgl); + +if (hwerrs & (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS)) +hwerr_crcbits (dd, hwerrs, msg, msgl); + +if (hwerrs &INFINIPATH_HWE_HTCMISCERR5 ) +strlcat (msg,"[HT core Misc5]" , msgl); +if (hwerrs &INFINIPATH_HWE_HTCMISCERR6 ) +strlcat (msg,"[HT core Misc6]" , msgl); +if (hwerrs &INFINIPATH_HWE_HTCMISCERR7 ) +strlcat (msg,"[HT core Misc7]" , msgl); +if (hwerrs &INFINIPATH_HWE_MEMBISTFAILED ) { +strlcat (msg,"[Memory BIST test failed, HT-400 unusable]" , + msgl); +/* ignore from now on, so disable until driver reloaded */ + dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } +#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \ + INFINIPATH_HWE_COREPLL_RFSLIP | \ + INFINIPATH_HWE_HTBPLL_FBSLIP | \ + INFINIPATH_HWE_HTBPLL_RFSLIP | \ + INFINIPATH_HWE_HTAPLL_FBSLIP | \ + INFINIPATH_HWE_HTAPLL_RFSLIP) + +if (hwerrs & _IPATH_PLL_FAIL) { +snprintf (bitsmsg,sizeof bitsmsg, +"[PLL failed (%llx), HT-400 unusable]" , + (unsigned long long ) (hwerrs & _IPATH_PLL_FAIL)); +strlcat (msg, bitsmsg, msgl); +/* ignore from now on, so disable until driver reloaded */ + dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL); +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + +if (hwerrs &INFINIPATH_HWE_SERDESPLLFAILED ) { +/* +* If it occurs, it is left masked since the eternal +* interface is unused +*/ + dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + +if (hwerrs &INFINIPATH_HWE_RXDSYNCMEMPARITYERR ) +strlcat (msg,"[Rx Dsync]" , msgl); +if (hwerrs &INFINIPATH_HWE_SERDESPLLFAILED ) +strlcat (msg,"[SerDes PLL]" , msgl); + +ipath_dev_err (dd,"%s hardware error\n" , msg); +if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) +/* +* for status file; if no trailing brace is copied, +* we'll know it was truncated. +*/ +snprintf (dd->ipath_freezemsg, + dd->ipath_freezelen,"{%s}" , msg); + +bail:; +} + +/** +* ipath_ht_boardname - fill in the board name +* @dd: the infinipath device +* @name: the output buffer +* @namelen: the size of the output buffer +* +* fill in the board name, based on the board revision register +*/ +static int ipath_ht_boardname (struct ipath_devdata *dd,char *name, +size_t namelen) +{ +char *n =NULL ; +u8 boardrev = dd->ipath_boardrev; +int ret; + +switch (boardrev) { +case 4 :/* Ponderosa is one of the bringup boards */ + n ="Ponderosa" ; +break ; +case 5 :/* HT-460 original production board */ + n ="InfiniPath_HT-460" ; +break ; +case 6 : + n ="OEM_Board_3" ; +break ; +case 7 : +/* HT-460 small form factor production board */ + n ="InfiniPath_HT-465" ; +break ; +case 8 : + n ="LS/X-1" ; +break ; +case 9 :/* Comstock bringup test board */ + n ="Comstock" ; +break ; +case 10 : + n ="OEM_Board_2" ; +break ; +case 11 : + n ="InfiniPath_HT-470" ; +break ; +case 12 : + n ="OEM_Board_4" ; +break ; +default :/* don't know, just print the number */ +ipath_dev_err (dd,"Don't yet know about board " +"with ID %u\n" , boardrev); +snprintf (name, namelen,"Unknown_InfiniPath_HT-4xx_%u" , + boardrev); +break ; + } +if (n) +snprintf (name, namelen,"%s" , n); + +if (dd->ipath_majrev !=3 || dd->ipath_minrev !=2 ) { +/* +* This version of the driver only supports the HT-400 +* Rev 3.2 +*/ +ipath_dev_err (dd, +"Unsupported HT-400 revision %u.%u!\n" , + dd->ipath_majrev, dd->ipath_minrev); + ret =1 ; + goto bail; + } +/* +* pkt/word counters are 32 bit, and therefore wrap fast enough +* that we snapshot them from a timer, and maintain 64 bit shadow +* copies +*/ + dd->ipath_flags |=IPATH_32BITCOUNTERS ; +if (dd->ipath_htspeed !=800 ) +ipath_dev_err (dd, +"Incorrectly configured for HT @ %uMHz\n" , + dd->ipath_htspeed); +if (dd->ipath_boardrev ==7 || dd->ipath_boardrev ==11 || + dd->ipath_boardrev ==6 ) + dd->ipath_flags |=IPATH_GPIO_INTR ; +else + dd->ipath_flags |=IPATH_POLL_RX_INTR ; +if (dd->ipath_boardrev ==8 ) {/* LS/X-1 */ +u64 val; + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_extstatus); +if (val &INFINIPATH_EXTS_SERDESSEL ) { +/* +* hardware disabled +* +* This means that the chip is hardware disabled, +* and will not be able to bring up the link, +* in any case. We special case this and abort +* early, to avoid later messages. We also set +* the DISABLED status bit +*/ +ipath_dbg ("Unit %u is hardware-disabled\n" , + dd->ipath_unit); + *dd->ipath_statusp |=IPATH_STATUS_DISABLED ; +/* this value is handled differently */ + ret =2 ; + goto bail; + } + } + ret =0 ; + +bail: +return ret; +} + +static void ipath_check_htlink (struct ipath_devdata *dd) +{ +u8 linkerr, link_off, i; + +for (i =0 ; i <2 ; i++) { + link_off = dd->ipath_ht_slave_off + i *4 +0xd ; +if (pci_read_config_byte (dd->pcidev, link_off, &linkerr)) +dev_info (&dd->pcidev->dev,"Couldn't read " +"linkerror%d of HT slave/primary block\n" , + i); +else if (linkerr &0xf0 ) { +ipath_cdbg (VERBOSE ,"HT linkerr%d bits 0x%x set, " +"clearing\n" , linkerr >>4 , i); +/* +* writing the linkerr bits that are set should +* clear them +*/ +if (pci_write_config_byte (dd->pcidev, link_off, + linkerr)) +ipath_dbg ("Failed write to clear HT " +"linkerror%d\n" , i); +if (pci_read_config_byte (dd->pcidev, link_off, + &linkerr)) +dev_info (&dd->pcidev->dev, +"Couldn't reread linkerror%d of " +"HT slave/primary block\n" , i); +else if (linkerr &0xf0 ) +dev_info (&dd->pcidev->dev, +"HT linkerror%d bits 0x%x " +"couldn't be cleared\n" , + i, linkerr >>4 ); + } + } +} + +static int ipath_setup_ht_reset (struct ipath_devdata *dd) +{ +ipath_dbg ("No reset possible for HT-400\n" ); +return 0 ; +} + +#define HT_CAPABILITY_ID 0x08/* HT capabilities not defined in kernel */ +#define HT_INTR_DISC_CONFIG 0x80/* HT interrupt and discovery cap */ +#define HT_INTR_REG_INDEX 2/* intconfig requires indirect accesses */ + +/* +* Bits 13-15 of command==0 is slave/primary block. Clear any HT CRC +* errors. We only bother to do this at load time, because it's OK if +* it happened before we were loaded (first time after boot/reset), +* but any time after that, it's fatal anyway. Also need to not check +* for for upper byte errors if we are in 8 bit mode, so figure out +* our width. For now, at least, also complain if it's 8 bit. +*/ +static void slave_or_pri_blk (struct ipath_devdata *dd,struct pci_dev *pdev, +int pos,u8 cap_type) +{ +u8 linkwidth =0 , linkerr, link_a_b_off, link_off; +u16 linkctrl =0 ; +int i; + + dd->ipath_ht_slave_off = pos; +/* command word, master_host bit */ +/* master host || slave */ +if ((cap_type >>2 ) &1 ) + link_a_b_off =4 ; +else + link_a_b_off =0 ; +ipath_cdbg (VERBOSE ,"HT%u (Link %c) connected to processor\n" , + link_a_b_off ?1 :0 , + link_a_b_off ?'B' :'A' ); + + link_a_b_off += pos; + +/* +* check both link control registers; clear both HT CRC sets if +* necessary. +*/ +for (i =0 ; i <2 ; i++) { + link_off = pos + i *4 +0x4 ; +if (pci_read_config_word (pdev, link_off, &linkctrl)) +ipath_dev_err (dd,"Couldn't read HT link control%d " +"register\n" , i); +else if (linkctrl & (0xf <<8 )) { +ipath_cdbg (VERBOSE ,"Clear linkctrl%d CRC Error " +"bits %x\n" , i, linkctrl & (0xf <<8 )); +/* +* now write them back to clear the error. +*/ +pci_write_config_byte (pdev, link_off, + linkctrl & (0xf <<8 )); + } + } + +/* +* As with HT CRC bits, same for protocol errors that might occur +* during boot. +*/ +for (i =0 ; i <2 ; i++) { + link_off = pos + i *4 +0xd ; +if (pci_read_config_byte (pdev, link_off, &linkerr)) +dev_info (&pdev->dev,"Couldn't read linkerror%d " +"of HT slave/primary block\n" , i); +else if (linkerr &0xf0 ) { +ipath_cdbg (VERBOSE ,"HT linkerr%d bits 0x%x set, " +"clearing\n" , linkerr >>4 , i); +/* +* writing the linkerr bits that are set will clear +* them +*/ +if (pci_write_config_byte + (pdev, link_off, linkerr)) +ipath_dbg ("Failed write to clear HT " +"linkerror%d\n" , i); +if (pci_read_config_byte (pdev, link_off, &linkerr)) +dev_info (&pdev->dev,"Couldn't reread " +"linkerror%d of HT slave/primary " +"block\n" , i); +else if (linkerr &0xf0 ) +dev_info (&pdev->dev,"HT linkerror%d bits " +"0x%x couldn't be cleared\n" , + i, linkerr >>4 ); + } + } + +/* +* this is just for our link to the host, not devices connected +* through tunnel. +*/ + +if (pci_read_config_byte (pdev, link_a_b_off +7 , &linkwidth)) +ipath_dev_err (dd,"Couldn't read HT link width " +"config register\n" ); +else { +u32 width; +switch (linkwidth &7 ) { +case 5 : + width =4 ; +break ; +case 4 : + width =2 ; +break ; +case 3 : + width =32 ; +break ; +case 1 : + width =16 ; +break ; +case 0 : +default :/* if wrong, assume 8 bit */ + width =8 ; +break ; + } + + dd->ipath_htwidth = width; + +if (linkwidth !=0x11 ) { +ipath_dev_err (dd,"Not configured for 16 bit HT " +"(%x)\n" , linkwidth); +if (!(linkwidth &0xf )) { +ipath_dbg ("Will ignore HT lane1 errors\n" ); + dd->ipath_flags |=IPATH_8BIT_IN_HT0 ; + } + } + } + +/* +* this is just for our link to the host, not devices connected +* through tunnel. +*/ +if (pci_read_config_byte (pdev, link_a_b_off +0xd , &linkwidth)) +ipath_dev_err (dd,"Couldn't read HT link frequency " +"config register\n" ); +else { +u32 speed; +switch (linkwidth &0xf ) { +case 6 : + speed =1000 ; +break ; +case 5 : + speed =800 ; +break ; +case 4 : + speed =600 ; +break ; +case 3 : + speed =500 ; +break ; +case 2 : + speed =400 ; +break ; +case 1 : + speed =300 ; +break ; +default : +/* +* assume reserved and vendor-specific are 200... +*/ +case 0 : + speed =200 ; +break ; + } + dd->ipath_htspeed = speed; + } +} + +static int set_int_handler (struct ipath_devdata *dd,struct pci_dev *pdev, +int pos) +{ +u32 int_handler_addr_lower; +u32 int_handler_addr_upper; +u64 ihandler; +u32 intvec; + +/* use indirection register to get the intr handler */ +pci_write_config_byte (pdev, pos +HT_INTR_REG_INDEX ,0x10 ); +pci_read_config_dword (pdev, pos +4 , &int_handler_addr_lower); +pci_write_config_byte (pdev, pos +HT_INTR_REG_INDEX ,0x11 ); +pci_read_config_dword (pdev, pos +4 , &int_handler_addr_upper); + + ihandler = (u64 ) int_handler_addr_lower | + ((u64 ) int_handler_addr_upper <<32 ); + +/* +* kernels with CONFIG_PCI_MSI set the vector in the irq field of +* struct pci_device, so we use that to program the HT-400 internal +* interrupt register (not config space) with that value. The BIOS +* must still have done the basic MSI setup. +*/ + intvec = pdev->irq; +/* +* clear any vector bits there; normally not set but we'll overload +* this for some debug purposes (setting the HTC debug register +* value from software, rather than GPIOs), so it might be set on a +* driver reload. +*/ + ihandler &= ~0xff0000 ; +/* x86 vector goes in intrinfo[23:16] */ + ihandler |= intvec <<16 ; +ipath_cdbg (VERBOSE ,"ihandler lower %x, upper %x, intvec %x, " +"interruptconfig %llx\n" , int_handler_addr_lower, + int_handler_addr_upper, intvec, + (unsigned long long ) ihandler); + +/* can't program yet, so save for interrupt setup */ + dd->ipath_intconfig = ihandler; +/* keep going, so we find link control stuff also */ + +return ihandler !=0 ; +} + +/** +* ipath_setup_ht_config - setup the interruptconfig register +* @dd: the infinipath device +* @pdev: the PCI device +* +* setup the interruptconfig register from the HT config info. +* Also clear CRC errors in HT linkcontrol, if necessary. +* This is done only for the real hardware. It is done before +* chip address space is initted, so can't touch infinipath registers +*/ +static int ipath_setup_ht_config (struct ipath_devdata *dd, +struct pci_dev *pdev) +{ +int pos, ret =0 ; +int ihandler =0 ; + +/* +* Read the capability info to find the interrupt info, and also +* handle clearing CRC errors in linkctrl register if necessary. We +* do this early, before we ever enable errors or hardware errors, +* mostly to avoid causing the chip to enter freeze mode. +*/ + pos =pci_find_capability (pdev,HT_CAPABILITY_ID ); +if (!pos) { +ipath_dev_err (dd,"Couldn't find HyperTransport " +"capability; no interrupts\n" ); + ret = -ENODEV ; + goto bail; + } +do { +u8 cap_type; + +/* the HT capability type byte is 3 bytes after the +* capability byte. +*/ +if (pci_read_config_byte (pdev, pos +3 , &cap_type)) { +dev_info (&pdev->dev,"Couldn't read config " +"command @ %d\n" , pos); +continue ; + } +if (!(cap_type &0xE0 )) +slave_or_pri_blk (dd, pdev, pos, cap_type); +else if (cap_type ==HT_INTR_DISC_CONFIG ) + ihandler =set_int_handler (dd, pdev, pos); + }while ((pos =pci_find_next_capability (pdev, pos, +HT_CAPABILITY_ID ))); + +if (!ihandler) { +ipath_dev_err (dd,"Couldn't find interrupt handler in " +"config space\n" ); + ret = -ENODEV ; + } + +bail: +return ret; +} + +/** +* ipath_setup_ht_cleanup - clean up any per-chip chip-specific stuff +* @dd: the infinipath device +* +* Called during driver unload. +* This is currently a nop for the HT-400, not for all chips +*/ +static void ipath_setup_ht_cleanup (struct ipath_devdata *dd) +{ +} + +/** +* ipath_setup_ht_setextled - set the state of the two external LEDs +* @dd: the infinipath device +* @lst: the L state +* @ltst: the LT state +* +* Set the state of the two external LEDs, to indicate physical and +* logical state of IB link. For this chip (at least with recommended +* board pinouts), LED1 is Green (physical state), and LED2 is Yellow +* (logical state) +* +* Note: We try to match the Mellanox HCA LED behavior as best +* we can. Green indicates physical link state is OK (something is +* plugged in, and we can train). +* Amber indicates the link is logically up (ACTIVE). +* Mellanox further blinks the amber LED to indicate data packet +* activity, but we have no hardware support for that, so it would +* require waking up every 10-20 msecs and checking the counters +* on the chip, and then turning the LED off if appropriate. That's +* visible overhead, so not something we will do. +* +*/ +static void ipath_setup_ht_setextled (struct ipath_devdata *dd, +u64 lst,u64 ltst) +{ +u64 extctl; + +/* the diags use the LED to indicate diag info, so we leave +* the external LED alone when the diags are running */ +if (ipath_diag_inuse) +return ; + +/* +* start by setting both LED control bits to off, then turn +* on the appropriate bit(s). +*/ +if (dd->ipath_boardrev ==8 ) {/* LS/X-1 uses different pins */ +/* +* major difference is that INFINIPATH_EXTC_LEDGBLERR_OFF +* is inverted, because it is normally used to indicate +* a hardware fault at reset, if there were errors +*/ + extctl = (dd->ipath_extctrl & ~INFINIPATH_EXTC_LEDGBLOK_ON ) + |INFINIPATH_EXTC_LEDGBLERR_OFF ; +if (ltst ==INFINIPATH_IBCS_LT_STATE_LINKUP ) + extctl &= ~INFINIPATH_EXTC_LEDGBLERR_OFF ; +if (lst ==INFINIPATH_IBCS_L_STATE_ACTIVE ) + extctl |=INFINIPATH_EXTC_LEDGBLOK_ON ; + } +else { + extctl = dd->ipath_extctrl & + ~(INFINIPATH_EXTC_LED1PRIPORT_ON | +INFINIPATH_EXTC_LED2PRIPORT_ON ); +if (ltst ==INFINIPATH_IBCS_LT_STATE_LINKUP ) + extctl |=INFINIPATH_EXTC_LED1PRIPORT_ON ; +if (lst ==INFINIPATH_IBCS_L_STATE_ACTIVE ) + extctl |=INFINIPATH_EXTC_LED2PRIPORT_ON ; + } + dd->ipath_extctrl = extctl; +ipath_write_kreg (dd, dd->ipath_kregs->kr_extctrl, extctl); +} + +static void ipath_init_ht_variables (void ) +{ + ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM; + ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM; + ipath_gpio_sda =IPATH_GPIO_SDA ; + ipath_gpio_scl =IPATH_GPIO_SCL ; + + infinipath_i_bitsextant = + (INFINIPATH_I_RCVURG_MASK <<INFINIPATH_I_RCVURG_SHIFT ) | + (INFINIPATH_I_RCVAVAIL_MASK << +INFINIPATH_I_RCVAVAIL_SHIFT ) | +INFINIPATH_I_ERROR |INFINIPATH_I_SPIOSENT | +INFINIPATH_I_SPIOBUFAVAIL |INFINIPATH_I_GPIO ; + + infinipath_e_bitsextant = +INFINIPATH_E_RFORMATERR |INFINIPATH_E_RVCRC | +INFINIPATH_E_RICRC |INFINIPATH_E_RMINPKTLEN | +INFINIPATH_E_RMAXPKTLEN |INFINIPATH_E_RLONGPKTLEN | +INFINIPATH_E_RSHORTPKTLEN |INFINIPATH_E_RUNEXPCHAR | +INFINIPATH_E_RUNSUPVL |INFINIPATH_E_REBP | +INFINIPATH_E_RIBFLOW |INFINIPATH_E_RBADVERSION | +INFINIPATH_E_RRCVEGRFULL |INFINIPATH_E_RRCVHDRFULL | +INFINIPATH_E_RBADTID |INFINIPATH_E_RHDRLEN | +INFINIPATH_E_RHDR |INFINIPATH_E_RIBLOSTLINK | +INFINIPATH_E_SMINPKTLEN |INFINIPATH_E_SMAXPKTLEN | +INFINIPATH_E_SUNDERRUN |INFINIPATH_E_SPKTLEN | +INFINIPATH_E_SDROPPEDSMPPKT |INFINIPATH_E_SDROPPEDDATAPKT | +INFINIPATH_E_SPIOARMLAUNCH |INFINIPATH_E_SUNEXPERRPKTNUM | +INFINIPATH_E_SUNSUPVL |INFINIPATH_E_IBSTATUSCHANGED | +INFINIPATH_E_INVALIDADDR |INFINIPATH_E_RESET | +INFINIPATH_E_HARDWARE ; + + infinipath_hwe_bitsextant = + (INFINIPATH_HWE_HTCMEMPARITYERR_MASK << +INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT ) | + (INFINIPATH_HWE_TXEMEMPARITYERR_MASK << +INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT ) | + (INFINIPATH_HWE_RXEMEMPARITYERR_MASK << +INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT ) | +INFINIPATH_HWE_HTCLNKABYTE0CRCERR | +INFINIPATH_HWE_HTCLNKABYTE1CRCERR | +INFINIPATH_HWE_HTCLNKBBYTE0CRCERR | +INFINIPATH_HWE_HTCLNKBBYTE1CRCERR | +INFINIPATH_HWE_HTCMISCERR4 | +INFINIPATH_HWE_HTCMISCERR5 |INFINIPATH_HWE_HTCMISCERR6 | +INFINIPATH_HWE_HTCMISCERR7 | +INFINIPATH_HWE_HTCBUSTREQPARITYERR | +INFINIPATH_HWE_HTCBUSTRESPPARITYERR | +INFINIPATH_HWE_HTCBUSIREQPARITYERR | +INFINIPATH_HWE_RXDSYNCMEMPARITYERR | +INFINIPATH_HWE_MEMBISTFAILED | +INFINIPATH_HWE_COREPLL_FBSLIP | +INFINIPATH_HWE_COREPLL_RFSLIP | +INFINIPATH_HWE_HTBPLL_FBSLIP | +INFINIPATH_HWE_HTBPLL_RFSLIP | +INFINIPATH_HWE_HTAPLL_FBSLIP | +INFINIPATH_HWE_HTAPLL_RFSLIP | +INFINIPATH_HWE_SERDESPLLFAILED | +INFINIPATH_HWE_IBCBUSTOSPCPARITYERR | +INFINIPATH_HWE_IBCBUSFRSPCPARITYERR ; + + infinipath_i_rcvavail_mask =INFINIPATH_I_RCVAVAIL_MASK ; + infinipath_i_rcvurg_mask =INFINIPATH_I_RCVURG_MASK ; +} + +/** +* ipath_ht_init_hwerrors - enable hardware errors +* @dd: the infinipath device +* +* now that we have finished initializing everything that might reasonably +* cause a hardware error, and cleared those errors bits as they occur, +* we can enable hardware errors in the mask (potentially enabling +* freeze mode), and enable hardware errors as errors (along with +* everything else) in errormask +*/ +static void ipath_ht_init_hwerrors (struct ipath_devdata *dd) +{ +ipath_err_t val; +u64 extsval; + + extsval =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_extstatus); + +if (!(extsval &INFINIPATH_EXTS_MEMBIST_ENDTEST )) +ipath_dev_err (dd,"MemBIST did not complete!\n" ); + +ipath_check_htlink (dd); + +/* barring bugs, all hwerrors become interrupts, which can */ + val =-1LL ; +/* don't look at crc lane1 if 8 bit */ +if (dd->ipath_flags &IPATH_8BIT_IN_HT0 ) + val &= ~infinipath_hwe_htclnkabyte1crcerr; +/* don't look at crc lane1 if 8 bit */ +if (dd->ipath_flags &IPATH_8BIT_IN_HT1 ) + val &= ~infinipath_hwe_htclnkbbyte1crcerr; + +/* +* disable RXDSYNCMEMPARITY because external serdes is unused, +* and therefore the logic will never be used or initialized, +* and uninitialized state will normally result in this error +* being asserted. Similarly for the external serdess pll +* lock signal. +*/ + val &= ~(INFINIPATH_HWE_SERDESPLLFAILED | +INFINIPATH_HWE_RXDSYNCMEMPARITYERR ); + +/* +* Disable MISCERR4 because of an inversion in the HT core +* logic checking for errors that cause this bit to be set. +* The errata can also cause the protocol error bit to be set +* in the HT config space linkerror register(s). +*/ + val &= ~INFINIPATH_HWE_HTCMISCERR4 ; + +/* +* PLL ignored because MDIO interface has a logic problem +* for reads, on Comstock and Ponderosa. BRINGUP +*/ +if (dd->ipath_boardrev ==4 || dd->ipath_boardrev ==9 ) + val &= ~INFINIPATH_HWE_SERDESPLLFAILED ; + dd->ipath_hwerrmask = val; +} + +/** +* ipath_ht_bringup_serdes - bring up the serdes +* @dd: the infinipath device +*/ +static int ipath_ht_bringup_serdes (struct ipath_devdata *dd) +{ +u64 val, config1; +int ret =0 , change =0 ; + +ipath_dbg ("Trying to bringup serdes\n" ); + +if (ipath_read_kreg64 (dd, dd->ipath_kregs->kr_hwerrstatus) & +INFINIPATH_HWE_SERDESPLLFAILED ) + { +ipath_dbg ("At start, serdes PLL failed bit set in " +"hwerrstatus, clearing and continuing\n" ); +ipath_write_kreg (dd, dd->ipath_kregs->kr_hwerrclear, +INFINIPATH_HWE_SERDESPLLFAILED ); + } + + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig0); + config1 =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig1); + +ipath_cdbg (VERBOSE ,"Initial serdes status is config0=%llx " +"config1=%llx, sstatus=%llx xgxs %llx\n" , + (unsigned long long ) val, (unsigned long long ) config1, + (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesstatus), + (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_xgxsconfig)); + +/* force reset on */ + val |=INFINIPATH_SERDC0_RESET_PLL +/* | INFINIPATH_SERDC0_RESET_MASK */ + ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, val); +udelay (15 );/* need pll reset set at least for a bit */ + +if (val &INFINIPATH_SERDC0_RESET_PLL ) { +u64 val2 = val &= ~INFINIPATH_SERDC0_RESET_PLL ; +/* set lane resets, and tx idle, during pll reset */ + val2 |=INFINIPATH_SERDC0_RESET_MASK | +INFINIPATH_SERDC0_TXIDLE ; +ipath_cdbg (VERBOSE ,"Clearing serdes PLL reset (writing " +"%llx)\n" , (unsigned long long ) val2); +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, + val2); +/* +* be sure chip saw it +*/ + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); +/* +* need pll reset clear at least 11 usec before lane +* resets cleared; give it a few more +*/ +udelay (15 ); + val = val2;/* for check below */ + } + +if (val & (INFINIPATH_SERDC0_RESET_PLL | +INFINIPATH_SERDC0_RESET_MASK | +INFINIPATH_SERDC0_TXIDLE )) { + val &= ~(INFINIPATH_SERDC0_RESET_PLL | +INFINIPATH_SERDC0_RESET_MASK | +INFINIPATH_SERDC0_TXIDLE ); +/* clear them */ +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, + val); + } + + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_xgxsconfig); +if (((val >>INFINIPATH_XGXS_MDIOADDR_SHIFT ) & +INFINIPATH_XGXS_MDIOADDR_MASK ) !=3 ) { + val &= ~(INFINIPATH_XGXS_MDIOADDR_MASK << +INFINIPATH_XGXS_MDIOADDR_SHIFT ); +/* +* we use address 3 +*/ + val |=3ULL <<INFINIPATH_XGXS_MDIOADDR_SHIFT ; + change =1 ; + } +if (val &INFINIPATH_XGXS_RESET ) { +/* normally true after boot */ + val &= ~INFINIPATH_XGXS_RESET ; + change =1 ; + } +if (change) +ipath_write_kreg (dd, dd->ipath_kregs->kr_xgxsconfig, val); + + val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig0); + +/* clear current and de-emphasis bits */ + config1 &= ~0x0ffffffff00ULL ; +/* set current to 20ma */ + config1 |=0x00000000000ULL ; +/* set de-emphasis to -5.68dB */ + config1 |=0x0cccc000000ULL ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig1, config1); + +ipath_cdbg (VERBOSE ,"After setup: serdes status is config0=%llx " +"config1=%llx, sstatus=%llx xgxs %llx\n" , + (unsigned long long ) val, (unsigned long long ) config1, + (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesstatus), + (unsigned long long ) +ipath_read_kreg64 (dd, dd->ipath_kregs->kr_xgxsconfig)); + +if (!ipath_waitfor_mdio_cmdready (dd)) { +ipath_write_kreg (dd, dd->ipath_kregs->kr_mdio, +ipath_mdio_req (IPATH_MDIO_CMD_READ ,31 , +IPATH_MDIO_CTRL_XGXS_REG_8 , +0 )); +if (ipath_waitfor_complete (dd, dd->ipath_kregs->kr_mdio, +IPATH_MDIO_DATAVALID , &val)) +ipath_dbg ("Never got MDIO data for XGXS status " +"read\n" ); +else +ipath_cdbg (VERBOSE ,"MDIO Read reg8, " +"'bank' 31 %x\n" , (u32 ) val); + }else +ipath_dbg ("Never got MDIO cmdready for XGXS status read\n" ); + +return ret;/* for now, say we always succeeded */ +} + +/** +* ipath_ht_quiet_serdes - set serdes to txidle +* @dd: the infinipath device +* driver is being unloaded +*/ +static void ipath_ht_quiet_serdes (struct ipath_devdata *dd) +{ +u64 val =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_serdesconfig0); + + val |=INFINIPATH_SERDC0_TXIDLE ; +ipath_dbg ("Setting TxIdleEn on serdes (config0 = %llx)\n" , + (unsigned long long ) val); +ipath_write_kreg (dd, dd->ipath_kregs->kr_serdesconfig0, val); +} + +static int ipath_ht_intconfig (struct ipath_devdata *dd) +{ +int ret; + +if (!dd->ipath_intconfig) { +ipath_dev_err (dd,"No interrupts enabled, couldn't setup " +"interrupt address\n" ); + ret =1 ; + goto bail; + } + +ipath_write_kreg (dd, dd->ipath_kregs->kr_interruptconfig, + dd->ipath_intconfig);/* interrupt address */ + ret =0 ; + +bail: +return ret; +} + +/** +* ipath_pe_put_tid - write a TID in chip +* @dd: the infinipath device +* @tidptr: pointer to the expected TID (in chip) to udpate +* @tidtype: 0 for eager, 1 for expected +* @pa: physical address of in memory buffer; ipath_tidinvalid if freeing +* +* This exists as a separate routine to allow for special locking etc. +* It's used for both the full cleanup on exit, as well as the normal +* setup and teardown. +*/ +static void ipath_ht_put_tid (struct ipath_devdata *dd, +u64 __iomem *tidptr,u32 type, +unsigned long pa) +{ +if (pa != dd->ipath_tidinvalid) { +if (unlikely ((pa & ~INFINIPATH_RT_ADDR_MASK ))) { +dev_info (&dd->pcidev->dev, +"physaddr %lx has more than " +"40 bits, using only 40!!!\n" , pa); + pa &=INFINIPATH_RT_ADDR_MASK ; + } +if (type ==0 ) + pa |= dd->ipath_tidtemplate; +else { +/* in words (fixed, full page). */ +u64 lenvalid =PAGE_SIZE >>2 ; + lenvalid <<=INFINIPATH_RT_BUFSIZE_SHIFT ; + pa |= lenvalid |INFINIPATH_RT_VALID ; + } + } +if (dd->ipath_kregbase) +writeq (pa, tidptr); +} + +/** +* ipath_ht_clear_tid - clear all TID entries for a port, expected and eager +* @dd: the infinipath device +* @port: the port +* +* Used from ipath_close(), and at chip initialization. +*/ +static void ipath_ht_clear_tids (struct ipath_devdata *dd,unsigned port) +{ +u64 __iomem *tidbase; +int i; + +if (!dd->ipath_kregbase) +return ; + +ipath_cdbg (VERBOSE ,"Invalidate TIDs for port %u\n" , port); + +/* +* need to invalidate all of the expected TID entries for this +* port, so we don't have valid entries that might somehow get +* used (early in next use of this port, or through some bug) +*/ + tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvtidbase + + port * dd->ipath_rcvtidcnt * +sizeof (*tidbase)); +for (i =0 ; i < dd->ipath_rcvtidcnt; i++) +ipath_ht_put_tid (dd, &tidbase[i],1 , dd->ipath_tidinvalid); + + tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvegrbase + + port * dd->ipath_rcvegrcnt * +sizeof (*tidbase)); + +for (i =0 ; i < dd->ipath_rcvegrcnt; i++) +ipath_ht_put_tid (dd, &tidbase[i],0 , dd->ipath_tidinvalid); +} + +/** +* ipath_ht_tidtemplate - setup constants for TID updates +* @dd: the infinipath device +* +* We setup stuff that we use a lot, to avoid calculating each time +*/ +static void ipath_ht_tidtemplate (struct ipath_devdata *dd) +{ + dd->ipath_tidtemplate = dd->ipath_ibmaxlen >>2 ; + dd->ipath_tidtemplate <<=INFINIPATH_RT_BUFSIZE_SHIFT ; + dd->ipath_tidtemplate |=INFINIPATH_RT_VALID ; + +/* +* work around chip errata bug 7358, by marking invalid tids +* as having max length +*/ + dd->ipath_tidinvalid = (-1LL &INFINIPATH_RT_BUFSIZE_MASK ) << +INFINIPATH_RT_BUFSIZE_SHIFT ; +} + +static int ipath_ht_early_init (struct ipath_devdata *dd) +{ +u32 __iomem *piobuf; +u32 pioincr, val32, egrsize; +int i; + +/* +* one cache line; long IB headers will spill over into received +* buffer +*/ + dd->ipath_rcvhdrentsize =16 ; + dd->ipath_rcvhdrsize =IPATH_DFLT_RCVHDRSIZE ; + +/* +* For HT-400, we allocate a somewhat overly large eager buffer, +* such that we can guarantee that we can receive the largest +* packet that we can send out. To truly support a 4KB MTU, +* we need to bump this to a large value. To date, other than +* testing, we have never encountered an HCA that can really +* send 4KB MTU packets, so we do not handle that (we'll get +* errors interrupts if we ever see one). +*/ + dd->ipath_rcvegrbufsize = dd->ipath_piosize2k; + egrsize = dd->ipath_rcvegrbufsize; + +/* +* the min() check here is currently a nop, but it may not +* always be, depending on just how we do ipath_rcvegrbufsize +*/ + dd->ipath_ibmaxlen =min (dd->ipath_piosize2k, + dd->ipath_rcvegrbufsize); + dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen; +ipath_ht_tidtemplate (dd); + +/* +* zero all the TID entries at startup. We do this for sanity, +* in case of a previous driver crash of some kind, and also +* because the chip powers up with these memories in an unknown +* state. Use portcnt, not cfgports, since this is for the +* full chip, not for current (possibly different) configuration +* value. +* Chip Errata bug 6447 +*/ +for (val32 =0 ; val32 < dd->ipath_portcnt; val32++) +ipath_ht_clear_tids (dd, val32); + +/* +* write the pbc of each buffer, to be sure it's initialized, then +* cancel all the buffers, and also abort any packets that might +* have been in flight for some reason (the latter is for driver +* unload/reload, but isn't a bad idea at first init). PIO send +* isn't enabled at this point, so there is no danger of sending +* these out on the wire. +* Chip Errata bug 6610 +*/ + piobuf = (u32 __iomem *) (((char __iomem *)(dd->ipath_kregbase)) + + dd->ipath_piobufbase); + pioincr = dd->ipath_palign /sizeof (*piobuf); +for (i =0 ; i < dd->ipath_piobcnt2k; i++) { +/* +* reasonable word count, just to init pbc +*/ +writel (16 , piobuf); + piobuf += pioincr; + } +/* +* self-clearing +*/ +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, +INFINIPATH_S_ABORT ); +return 0 ; +} + +/** +* ipath_init_ht_get_base_info - set chip-specific flags for user code +* @dd: the infinipath device +* @kbase: ipath_base_info pointer +* +* We set the PCIE flag because the lower bandwidth on PCIe vs +* HyperTransport can affect some user packet algorithims. +*/ +static int ipath_ht_get_base_info (struct ipath_portdata *pd,void *kbase) +{ +struct ipath_base_info *kinfo = kbase; + + kinfo->spi_runtime_flags |=IPATH_RUNTIME_HT | +IPATH_RUNTIME_RCVHDR_COPY ; + +return 0 ; +} + +/** +* ipath_init_ht400_funcs - set up the chip-specific function pointers +* @dd: the infinipath device +* +* This is global, and is called directly at init to set up the +* chip-specific function pointers for later use. +*/ +void ipath_init_ht400_funcs (struct ipath_devdata *dd) +{ + dd->ipath_f_intrsetup = ipath_ht_intconfig; + dd->ipath_f_bus = ipath_setup_ht_config; + dd->ipath_f_reset = ipath_setup_ht_reset; + dd->ipath_f_get_boardname = ipath_ht_boardname; + dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors; + dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors; + dd->ipath_f_early_init = ipath_ht_early_init; + dd->ipath_f_handle_hwerrors = ipath_ht_handle_hwerrors; + dd->ipath_f_quiet_serdes = ipath_ht_quiet_serdes; + dd->ipath_f_bringup_serdes = ipath_ht_bringup_serdes; + dd->ipath_f_clear_tids = ipath_ht_clear_tids; + dd->ipath_f_put_tid = ipath_ht_put_tid; + dd->ipath_f_cleanup = ipath_setup_ht_cleanup; + dd->ipath_f_setextled = ipath_setup_ht_setextled; + dd->ipath_f_get_base_info = ipath_ht_get_base_info; + +/* +* initialize chip-specific variables +*/ + dd->ipath_f_tidtemplate = ipath_ht_tidtemplate; + +/* +* setup the register offsets, since they are different for each +* chip +*/ + dd->ipath_kregs = &ipath_ht_kregs; + dd->ipath_cregs = &ipath_ht_cregs; + +/* +* do very early init that is needed before ipath_f_bus is +* called +*/ +ipath_init_ht_variables (); +}
PATCH 1/1 ipath - core driver header files
In reply to Bryan O'Sullivanipath_common.h and ips_common.h contain definitions shared between userspace and the kernel.
ipath_kernel.h is the core driver header file.
ipath_debug.h contains mask values used for controlling driver debugging.
ipath_registers.h contains bitmask definitions used in chip registers.
drivers/infiniband/hw/ipath/ipath_common.h new file +616 -0
@@ -0,0 +1,616 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#ifndef _IPATH_COMMON_H +#define _IPATH_COMMON_H + +/* +* This file contains defines, structures, etc. that are used +* to communicate between kernel and user code. +*/ + +/* This is the IEEE-assigned OUI for PathScale, Inc. */ +#define IPATH_SRC_OUI_1 0x00 +#define IPATH_SRC_OUI_2 0x11 +#define IPATH_SRC_OUI_3 0x75 + +/* version of protocol header (known to chip also). In the long run, +* we should be able to generate and accept a range of version numbers; +* for now we only accept one, and it's compiled in. +*/ +#define IPS_PROTO_VERSION 2 + +/* +* These are compile time constants that you may want to enable or disable +* if you are trying to debug problems with code or performance. +* IPATH_VERBOSE_TRACING define as 1 if you want additional tracing in +* fastpath code +* IPATH_TRACE_REGWRITES define as 1 if you want register writes to be +* traced in faspath code +* _IPATH_TRACING define as 0 if you want to remove all tracing in a +* compilation unit +* _IPATH_DEBUGGING define as 0 if you want to remove debug prints +*/ + +/* +* The value in the BTH QP field that InfiniPath uses to differentiate +* an infinipath protocol IB packet vs standard IB transport +*/ +#define IPATH_KD_QP 0x656b79 + +/* +* valid states passed to ipath_set_linkstate() user call +*/ +#define IPATH_IB_LINKDOWN 0 +#define IPATH_IB_LINKARM 1 +#define IPATH_IB_LINKACTIVE 2 +#define IPATH_IB_LINKINIT 3 +#define IPATH_IB_LINKDOWN_SLEEP 4 +#define IPATH_IB_LINKDOWN_DISABLE 5 + +/* +* stats maintained by the driver. For now, at least, this is global +* to all minor devices. +*/ +struct infinipath_stats { +/* number of interrupts taken */ +__u64 sps_ints; +/* number of interrupts for errors */ +__u64 sps_errints; +/* number of errors from chip (not incl. packet errors or CRC) */ +__u64 sps_errs; +/* number of packet errors from chip other than CRC */ +__u64 sps_pkterrs; +/* number of packets with CRC errors (ICRC and VCRC) */ +__u64 sps_crcerrs; +/* number of hardware errors reported (parity, etc.) */ +__u64 sps_hwerrs; +/* number of times IB link changed state unexpectedly */ +__u64 sps_iblink; +/* no longer used; left for compatibility */ +__u64 sps_unused3; +/* number of kernel (port0) packets received */ +__u64 sps_port0pkts; +/* number of "ethernet" packets sent by driver */ +__u64 sps_ether_spkts; +/* number of "ethernet" packets received by driver */ +__u64 sps_ether_rpkts; +/* number of SMA packets sent by driver */ +__u64 sps_sma_spkts; +/* number of SMA packets received by driver */ +__u64 sps_sma_rpkts; +/* number of times all ports rcvhdrq was full and packet dropped */ +__u64 sps_hdrqfull; +/* number of times all ports egrtid was full and packet dropped */ +__u64 sps_etidfull; +/* +* number of times we tried to send from driver, but no pio buffers +* avail +*/ +__u64 sps_nopiobufs; +/* number of ports currently open */ +__u64 sps_ports; +/* list of pkeys (other than default) accepted (0 means not set) */ +__u16 sps_pkeys[4 ]; +/* lids for up to 4 infinipaths, indexed by infinipath # */ +__u16 sps_lid[4 ]; +/* number of user ports per chip (not IB ports) */ +__u32 sps_nports; +/* not our interrupt, or already handled */ +__u32 sps_nullintr; +/* max number of packets handled per receive call */ +__u32 sps_maxpkts_call; +/* avg number of packets handled per receive call */ +__u32 sps_avgpkts_call; +/* total number of pages locked */ +__u64 sps_pagelocks; +/* total number of pages unlocked */ +__u64 sps_pageunlocks; +/* +* Number of packets dropped in kernel other than errors (ether +* packets if ipath not configured, sma/mad, etc.) +*/ +__u64 sps_krdrops; +/* mlids for up to 4 infinipaths, indexed by infinipath # */ +__u16 sps_mlid[4 ]; +/* pad for future growth */ +__u64 __sps_pad[45 ]; +}; + +/* +* These are the status bits readable (in ascii form, 64bit value) +* from the "status" sysfs file. +*/ +#define IPATH_STATUS_INITTED 0x1/* basic initialization done */ +#define IPATH_STATUS_DISABLED 0x2/* hardware disabled */ +/* Device has been disabled via admin request */ +#define IPATH_STATUS_ADMIN_DISABLED 0x4 +#define IPATH_STATUS_OIB_SMA 0x8/* ipath_mad kernel SMA running */ +#define IPATH_STATUS_SMA 0x10/* user SMA running */ +/* Chip has been found and initted */ +#define IPATH_STATUS_CHIP_PRESENT 0x20 +/* IB link is at ACTIVE, usable for data traffic */ +#define IPATH_STATUS_IB_READY 0x40 +/* link is configured, LID, MTU, etc. have been set */ +#define IPATH_STATUS_IB_CONF 0x80 +/* no link established, probably no cable */ +#define IPATH_STATUS_IB_NOCABLE 0x100 +/* A Fatal hardware error has occurred. */ +#define IPATH_STATUS_HWERROR 0x200 + +/* +* The list of usermode accessible registers. Also see Reg_* later in file. +*/ +typedef enum _ipath_ureg { +/* (RO) DMA RcvHdr to be used next. */ + ur_rcvhdrtail =0 , +/* (RW) RcvHdr entry to be processed next by host. */ + ur_rcvhdrhead =1 , +/* (RO) Index of next Eager index to use. */ + ur_rcvegrindextail =2 , +/* (RW) Eager TID to be processed next */ + ur_rcvegrindexhead =3 , +/* For internal use only; max register number. */ + _IPATH_UregMax +}ipath_ureg ; + +/* bit values for spi_runtime_flags */ +#define IPATH_RUNTIME_HT 0x1 +#define IPATH_RUNTIME_PCIE 0x2 +#define IPATH_RUNTIME_FORCE_WC_ORDER 0x4 +#define IPATH_RUNTIME_RCVHDR_COPY 0x8 + +/* +* This structure is returned by ipath_userinit() immediately after +* open to get implementation-specific info, and info specific to this +* instance. +* +* This struct must have explict pad fields where type sizes +* may result in different alignments between 32 and 64 bit +* programs, since the 64 bit * bit kernel requires the user code +* to have matching offsets +*/ +struct ipath_base_info { +/* version of hardware, for feature checking. */ +__u32 spi_hw_version; +/* version of software, for feature checking. */ +__u32 spi_sw_version; +/* InfiniPath port assigned, goes into sent packets */ +__u32 spi_port; +/* +* IB MTU, packets IB data must be less than this. +* The MTU is in bytes, and will be a multiple of 4 bytes. +*/ +__u32 spi_mtu; +/* +* Size of a PIO buffer. Any given packet's total size must be less +* than this (in words). Included is the starting control word, so +* if 513 is returned, then total pkt size is 512 words or less. +*/ +__u32 spi_piosize; +/* size of the TID cache in infinipath, in entries */ +__u32 spi_tidcnt; +/* size of the TID Eager list in infinipath, in entries */ +__u32 spi_tidegrcnt; +/* size of a single receive header queue entry. */ +__u32 spi_rcvhdrent_size; +/* +* Count of receive header queue entries allocated. +* This may be less than the spu_rcvhdrcnt passed in!. +*/ +__u32 spi_rcvhdr_cnt; + +/* per-chip and other runtime features bitmap (IPATH_RUNTIME_*) */ +__u32 spi_runtime_flags; + +/* address where receive buffer queue is mapped into */ +__u64 spi_rcvhdr_base; + +/* user program. */ + +/* base address of eager TID receive buffers. */ +__u64 spi_rcv_egrbufs; + +/* Allocated by initialization code, not by protocol. */ + +/* +* Size of each TID buffer in host memory, starting at +* spi_rcv_egrbufs. The buffers are virtually contiguous. +*/ +__u32 spi_rcv_egrbufsize; +/* +* The special QP (queue pair) value that identifies an infinipath +* protocol packet from standard IB packets. More, probably much +* more, to be added. +*/ +__u32 spi_qpair; + +/* +* User register base for init code, not to be used directly by +* protocol or applications. +*/ +__u64 __spi_uregbase; +/* +* Maximum buffer size in bytes that can be used in a single TID +* entry (assuming the buffer is aligned to this boundary). This is +* the minimum of what the hardware and software support Guaranteed +* to be a power of 2. +*/ +__u32 spi_tid_maxsize; +/* +* alignment of each pio send buffer (byte count +* to add to spi_piobufbase to get to second buffer) +*/ +__u32 spi_pioalign; +/* +* The index of the first pio buffer available to this process; +* needed to do lookup in spi_pioavailaddr; not added to +* spi_piobufbase. +*/ +__u32 spi_pioindex; +/* number of buffers mapped for this process */ +__u32 spi_piocnt; + +/* +* Base address of writeonly pio buffers for this process. +* Each buffer has spi_piosize words, and is aligned on spi_pioalign +* boundaries. spi_piocnt buffers are mapped from this address +*/ +__u64 spi_piobufbase; + +/* +* Base address of readonly memory copy of the pioavail registers. +* There are 2 bits for each buffer. +*/ +__u64 spi_pioavailaddr; + +/* +* Address where driver updates a copy of the interface and driver +* status (IPATH_STATUS_*) as a 64 bit value. It's followed by a +* string indicating hardware error, if there was one. +*/ +__u64 spi_status; + +/* number of chip ports available to user processes */ +__u32 spi_nports; +/* unit number of chip we are using */ +__u32 spi_unit; +/* num bufs in each contiguous set */ +__u32 spi_rcv_egrperchunk; +/* size in bytes of each contiguous set */ +__u32 spi_rcv_egrchunksize; +/* total size of mmap to cover full rcvegrbuffers */ +__u32 spi_rcv_egrbuftotlen; +} __attribute__ ((aligned (8 ))); + + +/* +* This version number is given to the driver by the user code during +* initialization in the spu_userversion field of ipath_user_info, so +* the driver can check for compatibility with user code. +* +* The major version changes when data structures +* change in an incompatible way. The driver must be the same or higher +* for initialization to succeed. In some cases, a higher version +* driver will not interoperate with older software, and initialization +* will return an error. +*/ +#define IPATH_USER_SWMAJOR 1 + +/* +* Minor version differences are always compatible +* a within a major version, however if if user software is larger +* than driver software, some new features and/or structure fields +* may not be implemented; the user code must deal with this if it +* cares, or it must abort after initialization reports the difference +*/ +#define IPATH_USER_SWMINOR 2 + +#define IPATH_USER_SWVERSION ((IPATH_USER_SWMAJOR<<16) | IPATH_USER_SWMINOR) + +#define IPATH_KERN_TYPE 0 + +/* +* Similarly, this is the kernel version going back to the user. It's +* slightly different, in that we want to tell if the driver was built as +* part of a PathScale release, or from the driver from OpenIB, kernel.org, +* or a standard distribution, for support reasons. The high bit is 0 for +* non-PathScale, and 1 for PathScale-built/supplied. +* +* It's returned by the driver to the user code during initialization in the +* spi_sw_version field of ipath_base_info, so the user code can in turn +* check for compatibility with the kernel. +*/ +#define IPATH_KERN_SWVERSION ((IPATH_KERN_TYPE<<31) | IPATH_USER_SWVERSION) + +/* +* This structure is passed to ipath_userinit() to tell the driver where +* user code buffers are, sizes, etc. The offsets and sizes of the +* fields must remain unchanged, for binary compatibility. It can +* be extended, if userversion is changed so user code can tell, if needed +*/ +struct ipath_user_info { +/* +* version of user software, to detect compatibility issues. +* Should be set to IPATH_USER_SWVERSION. +*/ +__u32 spu_userversion; + +/* desired number of receive header queue entries */ +__u32 spu_rcvhdrcnt; + +/* size of struct base_info to write to */ +__u32 spu_base_info_size; + +/* +* number of words in KD protocol header +* This tells InfiniPath how many words to copy to rcvhdrq. If 0, +* kernel uses a default. Once set, attempts to set any other value +* are an error (EAGAIN) until driver is reloaded. +*/ +__u32 spu_rcvhdrsize; + +/* +* cache line aligned (64 byte) user address to +* which the rcvhdrtail register will be written by infinipath +* whenever it changes, so that no chip registers are read in +* the performance path. +*/ +__u64 spu_rcvhdraddr; + +/* +* address of struct base_info to write to +*/ +__u64 spu_base_info; + +} __attribute__ ((aligned (8 ))); + +/* User commands. */ + +#define IPATH_CMD_MIN 16 + +#define IPATH_CMD_USER_INIT 16/* set up userspace */ +#define IPATH_CMD_PORT_INFO 17/* find out what resources we got */ +#define IPATH_CMD_RECV_CTRL 18/* control receipt of packets */ +#define IPATH_CMD_TID_UPDATE 19/* update expected TID entries */ +#define IPATH_CMD_TID_FREE 20/* free expected TID entries */ +#define IPATH_CMD_SET_PART_KEY 21/* add partition key */ + +#define IPATH_CMD_MAX 21 + +struct ipath_port_info { +__u32 num_active;/* number of active units */ +__u32 unit;/* unit (chip) assigned to caller */ +__u32 port;/* port on unit assigned to caller */ +}; + +struct ipath_tid_info { +__u32 tidcnt; +/* make structure same size in 32 and 64 bit */ +__u32 tid__unused; +/* virtual address of first page in transfer */ +__u64 tidvaddr; +/* pointer (same size 32/64 bit) to __u16 tid array */ +__u64 tidlist; + +/* +* pointer (same size 32/64 bit) to bitmap of TIDs used +* for this call; checked for being large enough at open +*/ +__u64 tidmap; +}; + +struct ipath_cmd { +__u32 type;/* command type */ +union { +struct ipath_tid_info tid_info; +struct ipath_user_info user_info; +/* address in userspace of struct ipath_port_info to +write result to */ +__u64 port_info; +/* enable/disable receipt of packets */ +__u32 recv_ctrl; +/* partition key to set */ +__u16 part_key; + } cmd; +}; + +struct ipath_iovec { +/* Pointer to data, but same size 32 and 64 bit */ +__u64 iov_base; + +/* +* Length of data; don't need 64 bits, but want +* ipath_sendpkt to remain same size as before 32 bit changes, so... +*/ +__u64 iov_len; +}; + +/* +* Describes a single packet for send. Each packet can have one or more +* buffers, but the total length (exclusive of IB headers) must be less +* than the MTU, and if using the PIO method, entire packet length, +* including IB headers, must be less than the ipath_piosize value (words). +* Use of this necessitates including sys/uio.h +*/ +struct __ipath_sendpkt { +__u32 sps_flags;/* flags for packet (TBD) */ +__u32 sps_cnt;/* number of entries to use in sps_iov */ +/* array of iov's describing packet. TEMPORARY */ +struct ipath_iovec sps_iov[4 ]; +}; + +/* Passed into SMA special file's ->read and ->write methods. */ +struct ipath_sma_pkt +{ +__u32 unit;/* unit on which to send packet */ +__u64 data;/* address of payload in userspace */ +__u32 len;/* length of payload */ +}; + +/* +* Data layout in I2C flash (for GUID, etc.) +* All fields are little-endian binary unless otherwise stated +*/ +#define IPATH_FLASH_VERSION 1 +struct ipath_flash { +/* flash layout version (IPATH_FLASH_VERSION) */ +__u8 if_fversion; +/* checksum protecting if_length bytes */ +__u8 if_csum; +/* +* valid length (in use, protected by if_csum), including +* if_fversion and if_sum themselves) +*/ +__u8 if_length; +/* the GUID, in network order */ +__u8 if_guid[8 ]; +/* number of GUIDs to use, starting from if_guid */ +__u8 if_numguid; +/* the board serial number, in ASCII */ +char if_serial[12 ]; +/* board mfg date (YYYYMMDD ASCII) */ +char if_mfgdate[8 ]; +/* last board rework/test date (YYYYMMDD ASCII) */ +char if_testdate[8 ]; +/* logging of error counts, TBD */ +__u8 if_errcntp[4 ]; +/* powered on hours, updated at driver unload */ +__u8 if_powerhour[2 ]; +/* ASCII free-form comment field */ +char if_comment[32 ]; +/* 78 bytes used, min flash size is 128 bytes */ +__u8 if_future[50 ]; +}; + +/* +* These are the counters implemented in the chip, and are listed in order. +* The InterCaps naming is taken straight from the chip spec. +*/ +struct infinipath_counters { +__u64 LBIntCnt; +__u64 LBFlowStallCnt; +__u64 Reserved1; +__u64 TxUnsupVLErrCnt; +__u64 TxDataPktCnt; +__u64 TxFlowPktCnt; +__u64 TxDwordCnt; +__u64 TxLenErrCnt; +__u64 TxMaxMinLenErrCnt; +__u64 TxUnderrunCnt; +__u64 TxFlowStallCnt; +__u64 TxDroppedPktCnt; +__u64 RxDroppedPktCnt; +__u64 RxDataPktCnt; +__u64 RxFlowPktCnt; +__u64 RxDwordCnt; +__u64 RxLenErrCnt; +__u64 RxMaxMinLenErrCnt; +__u64 RxICRCErrCnt; +__u64 RxVCRCErrCnt; +__u64 RxFlowCtrlErrCnt; +__u64 RxBadFormatCnt; +__u64 RxLinkProblemCnt; +__u64 RxEBPCnt; +__u64 RxLPCRCErrCnt; +__u64 RxBufOvflCnt; +__u64 RxTIDFullErrCnt; +__u64 RxTIDValidErrCnt; +__u64 RxPKeyMismatchCnt; +__u64 RxP0HdrEgrOvflCnt; +__u64 RxP1HdrEgrOvflCnt; +__u64 RxP2HdrEgrOvflCnt; +__u64 RxP3HdrEgrOvflCnt; +__u64 RxP4HdrEgrOvflCnt; +__u64 RxP5HdrEgrOvflCnt; +__u64 RxP6HdrEgrOvflCnt; +__u64 RxP7HdrEgrOvflCnt; +__u64 RxP8HdrEgrOvflCnt; +__u64 Reserved6; +__u64 Reserved7; +__u64 IBStatusChangeCnt; +__u64 IBLinkErrRecoveryCnt; +__u64 IBLinkDownedCnt; +__u64 IBSymbolErrCnt; +}; + +/* +* The next set of defines are for packet headers, and chip register +* and memory bits that are visible to and/or used by user-mode software +* The other bits that are used only by the driver or diags are in +* ipath_registers.h +*/ + +/* RcvHdrFlags bits */ +#define INFINIPATH_RHF_LENGTH_MASK 0x7FF +#define INFINIPATH_RHF_LENGTH_SHIFT 0 +#define INFINIPATH_RHF_RCVTYPE_MASK 0x7 +#define INFINIPATH_RHF_RCVTYPE_SHIFT 11 +#define INFINIPATH_RHF_EGRINDEX_MASK 0x7FF +#define INFINIPATH_RHF_EGRINDEX_SHIFT 16 +#define INFINIPATH_RHF_H_ICRCERR 0x80000000 +#define INFINIPATH_RHF_H_VCRCERR 0x40000000 +#define INFINIPATH_RHF_H_PARITYERR 0x20000000 +#define INFINIPATH_RHF_H_LENERR 0x10000000 +#define INFINIPATH_RHF_H_MTUERR 0x08000000 +#define INFINIPATH_RHF_H_IHDRERR 0x04000000 +#define INFINIPATH_RHF_H_TIDERR 0x02000000 +#define INFINIPATH_RHF_H_MKERR 0x01000000 +#define INFINIPATH_RHF_H_IBERR 0x00800000 +#define INFINIPATH_RHF_L_SWA 0x00008000 +#define INFINIPATH_RHF_L_SWB 0x00004000 + +/* infinipath header fields */ +#define INFINIPATH_I_VERS_MASK 0xF +#define INFINIPATH_I_VERS_SHIFT 28 +#define INFINIPATH_I_PORT_MASK 0xF +#define INFINIPATH_I_PORT_SHIFT 24 +#define INFINIPATH_I_TID_MASK 0x7FF +#define INFINIPATH_I_TID_SHIFT 13 +#define INFINIPATH_I_OFFSET_MASK 0x1FFF +#define INFINIPATH_I_OFFSET_SHIFT 0 + +/* K_PktFlags bits */ +#define INFINIPATH_KPF_INTR 0x1 + +/* SendPIO per-buffer control */ +#define INFINIPATH_SP_LENGTHP1_MASK 0x3FF +#define INFINIPATH_SP_LENGTHP1_SHIFT 0 +#define INFINIPATH_SP_INTR 0x80000000 +#define INFINIPATH_SP_TEST 0x40000000 +#define INFINIPATH_SP_TESTEBP 0x20000000 + +/* SendPIOAvail bits */ +#define INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT 1 +#define INFINIPATH_SENDPIOAVAIL_CHECK_SHIFT 0 + +#endif /* _IPATH_COMMON_H */
drivers/infiniband/hw/ipath/ipath_debug.h new file +96 -0
96 lines not on this page · raw message
drivers/infiniband/hw/ipath/ipath_kernel.h new file +884 -0
884 lines not on this page · raw message
drivers/infiniband/hw/ipath/ipath_registers.h new file +446 -0
446 lines not on this page · raw message
drivers/infiniband/hw/ipath/ips_common.h new file +263 -0
263 lines not on this page · raw message
PATCH 1/1 ipath - chip initialisation code, and diag support
In reply to Bryan O'Sullivanipath_init_chip.c sets up an InfiniPath device for use.
ipath_diag.c permits userspace diagnostic tools to read and write a chip's registers. It is different in purpose from the mmap interfaces to the /sys/bus/pci resource files.
drivers/infiniband/hw/ipath/ipath_diag.c new file +379 -0
@@ -0,0 +1,379 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +/* +* This file contains support for diagnostic functions. It is accessed by +* opening the ipath_diag device, normally minor number 129. Diagnostic use +* of the InfiniPath chip may render the chip or board unusable until the +* driver is unloaded, or in some cases, until the system is rebooted. +* +* Accesses to the chip through this interface are not similar to going +* through the /sys/bus/pci resource mmap interface. +*/ + +#include <linux/pci.h> +#include <asm/uaccess.h> + +#include "ipath_common.h" +#include "ipath_kernel.h" +#include "ips_common.h" +#include "ipath_layer.h" + +int ipath_diag_inuse; +static int diag_set_link; + +static int ipath_diag_open (struct inode *in,struct file *fp); +static int ipath_diag_release (struct inode *in,struct file *fp); +static ssize_t ipath_diag_read (struct file *fp,char __user *data, +size_t count,loff_t *off); +static ssize_t ipath_diag_write (struct file *fp,const char __user *data, +size_t count,loff_t *off); + +static struct file_operations diag_file_ops = { + .owner =THIS_MODULE , + .write = ipath_diag_write, + .read = ipath_diag_read, + .open = ipath_diag_open, + .release = ipath_diag_release +}; + +static struct cdev *diag_cdev; +static struct class_device *diag_class_dev; + +int ipath_diag_init (void ) +{ +return ipath_cdev_init (IPATH_DIAG_MINOR ,"ipath_diag" , + &diag_file_ops, &diag_cdev, &diag_class_dev); +} + +void ipath_diag_cleanup (void ) +{ +ipath_cdev_cleanup (&diag_cdev, &diag_class_dev); +} + +/** +* ipath_read_umem64 - read a 64-bit quantity from the chip into user space +* @dd: the infinipath device +* @uaddr: the location to store the data in user memory +* @caddr: the source chip address (full pointer, not offset) +* @count: number of bytes to copy (multiple of 32 bits) +* +* This function also localizes all chip memory accesses. +* The copy should be written such that we read full cacheline packets +* from the chip. This is usually used for a single qword +* +* NOTE: This assumes the chip address is 64-bit aligned. +*/ +static int ipath_read_umem64 (struct ipath_devdata *dd,void __user *uaddr, +const void __iomem *caddr,size_t count) +{ +const u64 __iomem *reg_addr = caddr; +const u64 __iomem *reg_end = reg_addr + (count /sizeof (u64)); +int ret; + +/* not very efficient, but it works for now */ +if (reg_addr < dd->ipath_kregbase || + reg_end > dd->ipath_kregend) { + ret = -EINVAL ; + goto bail; + } +while (reg_addr < reg_end) { +u64 data =readq (reg_addr); +if (copy_to_user (uaddr, &data,sizeof (u64))) { + ret = -EFAULT ; + goto bail; + } + reg_addr++; + uaddr++; + } + ret =0 ; +bail: +return ret; +} + +/** +* ipath_write_umem64 - write a 64-bit quantity to the chip from user space +* @dd: the infinipath device +* @caddr: the destination chip address (full pointer, not offset) +* @uaddr: the source of the data in user memory +* @count: the number of bytes to copy (multiple of 32 bits) +* +* This is usually used for a single qword +* NOTE: This assumes the chip address is 64-bit aligned. +*/ + +static int ipath_write_umem64 (struct ipath_devdata *dd,void __iomem *caddr, +const void __user *uaddr,size_t count) +{ +u64 __iomem *reg_addr = caddr; +const u64 __iomem *reg_end = reg_addr + (count /sizeof (u64)); +int ret; + +/* not very efficient, but it works for now */ +if (reg_addr < dd->ipath_kregbase || + reg_end > dd->ipath_kregend) { + ret = -EINVAL ; + goto bail; + } +while (reg_addr < reg_end) { +u64 data; +if (copy_from_user (&data, uaddr,sizeof (data))) { + ret = -EFAULT ; + goto bail; + } +writeq (data, reg_addr); + + reg_addr++; + uaddr++; + } + ret =0 ; +bail: +return ret; +} + +/** +* ipath_read_umem32 - read a 32-bit quantity from the chip into user space +* @dd: the infinipath device +* @uaddr: the location to store the data in user memory +* @caddr: the source chip address (full pointer, not offset) +* @count: number of bytes to copy +* +* read 32 bit values, not 64 bit; for memories that only +* support 32 bit reads; usually a single dword. +*/ +static int ipath_read_umem32 (struct ipath_devdata *dd,void __user *uaddr, +const void __iomem *caddr,size_t count) +{ +const u32 __iomem *reg_addr = caddr; +const u32 __iomem *reg_end = reg_addr + (count /sizeof (u32)); +int ret; + +if (reg_addr < (u32 __iomem *) dd->ipath_kregbase || + reg_end > (u32 __iomem *) dd->ipath_kregend) { + ret = -EINVAL ; + goto bail; + } +/* not very efficient, but it works for now */ +while (reg_addr < reg_end) { +u32 data =readl (reg_addr); +if (copy_to_user (uaddr, &data,sizeof (data))) { + ret = -EFAULT ; + goto bail; + } + + reg_addr++; + uaddr++; + } + ret =0 ; +bail: +return ret; +} + +/** +* ipath_write_umem32 - write a 32-bit quantity to the chip from user space +* @dd: the infinipath device +* @caddr: the destination chip address (full pointer, not offset) +* @uaddr: the source of the data in user memory +* @count: number of bytes to copy +* +* write 32 bit values, not 64 bit; for memories that only +* support 32 bit write; usually a single dword. +*/ + +static int ipath_write_umem32 (struct ipath_devdata *dd,void __iomem *caddr, +const void __user *uaddr,size_t count) +{ +u32 __iomem *reg_addr = caddr; +const u32 __iomem *reg_end = reg_addr + (count /sizeof (u32)); +int ret; + +if (reg_addr < (u32 __iomem *) dd->ipath_kregbase || + reg_end > (u32 __iomem *) dd->ipath_kregend) { + ret = -EINVAL ; + goto bail; + } +while (reg_addr < reg_end) { +u32 data; +if (copy_from_user (&data, uaddr,sizeof (data))) { + ret = -EFAULT ; + goto bail; + } +writel (data, reg_addr); + + reg_addr++; + uaddr++; + } + ret =0 ; +bail: +return ret; +} + +static int ipath_diag_open (struct inode *in,struct file *fp) +{ +struct ipath_devdata *dd; +int unit =0 ;/* XXX this is bogus */ +unsigned long flags; +int ret; + + dd =ipath_lookup (unit); + +mutex_lock (&ipath_mutex); +spin_lock_irqsave (&ipath_devs_lock, flags); + +if (ipath_diag_inuse) { + ret = -EBUSY ; + goto bail; + } + +list_for_each_entry (dd, &ipath_dev_list, ipath_list) { +/* +* we need at least one infinipath device to be present +* (don't use INITTED, because we want to be able to open +* even if device is in freeze mode, which cleared INITTED). +* There is a small amount of risk to this, which is why we +* also verify kregbase is set. +*/ + +if (!(dd->ipath_flags &IPATH_PRESENT ) || + !dd->ipath_kregbase) +continue ; + + ipath_diag_inuse =1 ; + diag_set_link =0 ; + ret =0 ; + goto bail; + } + + ret = -ENODEV ; + +bail: +spin_unlock_irqrestore (&ipath_devs_lock, flags); +mutex_unlock (&ipath_mutex); + +/* Only expose a way to reset the device if we +make it into diag mode. */ +if (ret ==0 ) +ipath_expose_reset (&dd->pcidev->dev); + +return ret; +} + +static int ipath_diag_release (struct inode *i,struct file *f) +{ +mutex_lock (&ipath_mutex); + ipath_diag_inuse =0 ; +mutex_unlock (&ipath_mutex); +return 0 ; +} + +static ssize_t ipath_diag_read (struct file *fp,char __user *data, +size_t count,loff_t *off) +{ +int unit =0 ;/* XXX provide for reads on other units some day */ +struct ipath_devdata *dd; +void __iomem *kreg_base; +ssize_t ret; + + dd =ipath_lookup (unit); +if (!dd) { + ret = -ENODEV ; + goto bail; + } + + kreg_base = dd->ipath_kregbase; + +if (count ==0 ) + ret =0 ; +else if ((count %4 ) || (*off %4 )) +/* address or length is not 32-bit aligned, hence invalid */ + ret = -EINVAL ; +else if ((count %8 ) || (*off %8 )) +/* address or length not 64-bit aligned; do 32-bit reads */ + ret =ipath_read_umem32 (dd, data, kreg_base + *off, count); +else + ret =ipath_read_umem64 (dd, data, kreg_base + *off, count); + +if (ret >=0 ) { + *off += count; + ret = count; + } + +bail: +return ret; +} + +static ssize_t ipath_diag_write (struct file *fp,const char __user *data, +size_t count,loff_t *off) +{ +int unit =0 ;/* XXX this is bogus */ +struct ipath_devdata *dd; +void __iomem *kreg_base; +ssize_t ret; + + dd =ipath_lookup (unit); +if (!dd) { + ret = -ENODEV ; + goto bail; + } + kreg_base = dd->ipath_kregbase; + +if (count ==0 ) + ret =0 ; +else if ((count %4 ) || (*off %4 )) +/* address or length is not 32-bit aligned, hence invalid */ + ret = -EINVAL ; +else if ((count %8 ) || (*off %8 )) +/* address or length not 64-bit aligned; do 32-bit writes */ + ret =ipath_write_umem32 (dd, kreg_base + *off, data, count); +else + ret =ipath_write_umem64 (dd, kreg_base + *off, data, count); + +if (ret >=0 ) { + *off += count; + ret = count; + } + +bail: +return ret; +} + +void ipath_diag_bringup_link (struct ipath_devdata *dd) +{ +if (diag_set_link || (dd->ipath_flags &IPATH_LINKACTIVE )) +return ; + + diag_set_link =1 ; +ipath_cdbg (VERBOSE ,"Trying to set to set link active for " +"diag pkt\n" ); +ipath_layer_set_linkstate (dd,IPATH_IB_LINKARM ); +ipath_layer_set_linkstate (dd,IPATH_IB_LINKACTIVE ); +}
drivers/infiniband/hw/ipath/ipath_init_chip.c new file +951 -0
951 lines not on this page · raw message
PATCH 1/1 ipath - infiniband RC protocol support
In reply to Bryan O'SullivanThis is an implementation of the Infiniband RC ("reliable connection") protocol.
drivers/infiniband/hw/ipath/ipath_rc.c new file +1857 -0
@@ -0,0 +1,1857 @@ +/* +* Copyright (c) 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include "ipath_verbs.h" +#include "ips_common.h" + +/* cut down ridiculously long IB macro names */ +#define OP (x) IB_OPCODE_RC_##x + +/** +* ipath_init_restart- initialize the qp->s_sge after a restart +* @qp: the QP who's SGE we're restarting +* @wqe: the work queue to initialize the QP's SGE from +* +* The QP s_lock should be held. +*/ +static void ipath_init_restart (struct ipath_qp *qp,struct ipath_swqe *wqe) +{ +struct ipath_ibdev *dev; +u32 len; + + len = ((qp->s_psn - wqe->psn) &IPS_PSN_MASK ) * +ib_mtu_enum_to_int (qp->path_mtu); + qp->s_sge.sge = wqe->sg_list[0 ]; + qp->s_sge.sg_list = wqe->sg_list +1 ; + qp->s_sge.num_sge = wqe->wr.num_sge; +ipath_skip_sge (&qp->s_sge, len); + qp->s_len = wqe->length - len; + dev =to_idev (qp->ibqp.device); +spin_lock (&dev->pending_lock); +if (qp->timerwait.next ==LIST_POISON1 ) +list_add_tail (&qp->timerwait, + &dev->pending[dev->pending_index]); +spin_unlock (&dev->pending_lock); +} + +/** +* ipath_make_rc_ack - construct a response packet (ACK, NAK, or RDMA read) +* @qp: a pointer to the QP +* @ohdr: a pointer to the IB header being constructed +* @pmtu: the path MTU +* +* Return bth0 if constructed; otherwise, return 0. +* Note the QP s_lock must be held. +*/ +static inline u32 ipath_make_rc_ack (struct ipath_qp *qp, +struct ipath_other_headers *ohdr, +u32 pmtu) +{ +struct ipath_sge_state *ss; +u32 hwords; +u32 len; +u32 bth0; + +/* header size in 32-bit words LRH+BTH = (8+12)/4. */ + hwords =5 ; + +/* +* Send a response. Note that we are in the responder's +* side of the QP context. +*/ +switch (qp->s_ack_state) { +case OP (RDMA_READ_REQUEST ): + ss = &qp->s_rdma_sge; + len = qp->s_rdma_len; +if (len > pmtu) { + len = pmtu; + qp->s_ack_state =OP (RDMA_READ_RESPONSE_FIRST ); + } +else + qp->s_ack_state =OP (RDMA_READ_RESPONSE_ONLY ); + qp->s_rdma_len -= len; + bth0 = qp->s_ack_state <<24 ; + ohdr->u.aeth =ipath_compute_aeth (qp); + hwords++; +break ; + +case OP (RDMA_READ_RESPONSE_FIRST ): + qp->s_ack_state =OP (RDMA_READ_RESPONSE_MIDDLE ); +/* FALLTHROUGH */ +case OP (RDMA_READ_RESPONSE_MIDDLE ): + ss = &qp->s_rdma_sge; + len = qp->s_rdma_len; +if (len > pmtu) + len = pmtu; +else { + ohdr->u.aeth =ipath_compute_aeth (qp); + hwords++; + qp->s_ack_state =OP (RDMA_READ_RESPONSE_LAST ); + } + qp->s_rdma_len -= len; + bth0 = qp->s_ack_state <<24 ; +break ; + +case OP (RDMA_READ_RESPONSE_LAST ): +case OP (RDMA_READ_RESPONSE_ONLY ): +/* +* We have to prevent new requests from changing +* the r_sge state while a ipath_verbs_send() +* is in progress. +* Changing r_state allows the receiver +* to continue processing new packets. +* We do it here now instead of above so +* that we are sure the packet was sent before +* changing the state. +*/ + qp->r_state =OP (RDMA_READ_RESPONSE_LAST ); + qp->s_ack_state =OP (ACKNOWLEDGE ); +return 0 ; + +case OP (COMPARE_SWAP ): +case OP (FETCH_ADD ): + ss =NULL ; + len =0 ; + qp->r_state =OP (SEND_LAST ); + qp->s_ack_state =OP (ACKNOWLEDGE ); + bth0 =IB_OPCODE_ATOMIC_ACKNOWLEDGE <<24 ; + ohdr->u.at.aeth =ipath_compute_aeth (qp); + ohdr->u.at.atomic_ack_eth =cpu_to_be64 (qp->s_ack_atomic); + hwords +=sizeof (ohdr->u.at) /4 ; +break ; + +default : +/* Send a regular ACK. */ + ss =NULL ; + len =0 ; + qp->s_ack_state =OP (ACKNOWLEDGE ); + bth0 = qp->s_ack_state <<24 ; + ohdr->u.aeth =ipath_compute_aeth (qp); + hwords++; + } + qp->s_hdrwords = hwords; + qp->s_cur_sge = ss; + qp->s_cur_size = len; + +return bth0; +} + +/** +* ipath_make_rc_req - construct a request packet (SEND, RDMA r/w, ATOMIC) +* @qp: a pointer to the QP +* @ohdr: a pointer to the IB header being constructed +* @pmtu: the path MTU +* @bth0p: pointer to the BTH opcode word +* @bth2p: pointer to the BTH PSN word +* +* Return 1 if constructed; otherwise, return 0. +* Note the QP s_lock must be held. +*/ +static inline int ipath_make_rc_req (struct ipath_qp *qp, +struct ipath_other_headers *ohdr, +u32 pmtu,u32 *bth0p,u32 *bth2p) +{ +struct ipath_ibdev *dev =to_idev (qp->ibqp.device); +struct ipath_sge_state *ss; +struct ipath_swqe *wqe; +u32 hwords; +u32 len; +u32 bth0; +u32 bth2; +char newreq; + +if (!(ib_ipath_state_ops[qp->state] &IPATH_PROCESS_SEND_OK ) || + qp->s_rnr_timeout) + goto done; + +/* header size in 32-bit words LRH+BTH = (8+12)/4. */ + hwords =5 ; + bth0 =0 ; + +/* Send a request. */ + wqe =get_swqe_ptr (qp, qp->s_cur); +switch (qp->s_state) { +default : +/* +* Resend an old request or start a new one. +* +* We keep track of the current SWQE so that +* we don't reset the "furthest progress" state +* if we need to back up. +*/ + newreq =0 ; +if (qp->s_cur == qp->s_tail) { +/* Check if send work queue is empty. */ +if (qp->s_tail == qp->s_head) + goto done; + qp->s_psn = wqe->psn = qp->s_next_psn; + newreq =1 ; + } +/* +* Note that we have to be careful not to modify the +* original work request since we may need to resend +* it. +*/ + qp->s_sge.sge = wqe->sg_list[0 ]; + qp->s_sge.sg_list = wqe->sg_list +1 ; + qp->s_sge.num_sge = wqe->wr.num_sge; + qp->s_len = len = wqe->length; + ss = &qp->s_sge; + bth2 =0 ; +switch (wqe->wr.opcode) { +case IB_WR_SEND : +case IB_WR_SEND_WITH_IMM : +/* If no credit, return. */ +if (qp->s_lsn != (u32) -1 && +ipath_cmp24 (wqe->ssn, qp->s_lsn +1 ) >0 ) + goto done; + wqe->lpsn = wqe->psn; +if (len > pmtu) { + wqe->lpsn += (len -1 ) / pmtu; + qp->s_state =OP (SEND_FIRST ); + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_SEND ) + qp->s_state =OP (SEND_ONLY ); +else { + qp->s_state =OP (SEND_ONLY_WITH_IMMEDIATE ); +/* Immediate data comes after the BTH */ + ohdr->u.imm_data = wqe->wr.imm_data; + hwords +=1 ; + } +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; + bth2 =1 <<31 ;/* Request ACK. */ +if (++qp->s_cur == qp->s_size) + qp->s_cur =0 ; +break ; + +case IB_WR_RDMA_WRITE : +if (newreq) + qp->s_lsn++; +/* FALLTHROUGH */ +case IB_WR_RDMA_WRITE_WITH_IMM : +/* If no credit, return. */ +if (qp->s_lsn != (u32) -1 && +ipath_cmp24 (wqe->ssn, qp->s_lsn +1 ) >0 ) + goto done; + ohdr->u.rc.reth.vaddr = +cpu_to_be64 (wqe->wr.wr.rdma.remote_addr); + ohdr->u.rc.reth.rkey = +cpu_to_be32 (wqe->wr.wr.rdma.rkey); + ohdr->u.rc.reth.length =cpu_to_be32 (len); + hwords +=sizeof (struct ib_reth ) /4 ; + wqe->lpsn = wqe->psn; +if (len > pmtu) { + wqe->lpsn += (len -1 ) / pmtu; + qp->s_state =OP (RDMA_WRITE_FIRST ); + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_RDMA_WRITE ) + qp->s_state =OP (RDMA_WRITE_ONLY ); +else { + qp->s_state = +OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE ); +/* Immediate data comes +* after RETH */ + ohdr->u.rc.imm_data = wqe->wr.imm_data; + hwords +=1 ; +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; + } + bth2 =1 <<31 ;/* Request ACK. */ +if (++qp->s_cur == qp->s_size) + qp->s_cur =0 ; +break ; + +case IB_WR_RDMA_READ : + ohdr->u.rc.reth.vaddr = +cpu_to_be64 (wqe->wr.wr.rdma.remote_addr); + ohdr->u.rc.reth.rkey = +cpu_to_be32 (wqe->wr.wr.rdma.rkey); + ohdr->u.rc.reth.length =cpu_to_be32 (len); + qp->s_state =OP (RDMA_READ_REQUEST ); + hwords +=sizeof (ohdr->u.rc.reth) /4 ; +if (newreq) { + qp->s_lsn++; +/* +* Adjust s_next_psn to count the +* expected number of responses. +*/ +if (len > pmtu) + qp->s_next_psn += (len -1 ) / pmtu; + wqe->lpsn = qp->s_next_psn++; + } + ss =NULL ; + len =0 ; +if (++qp->s_cur == qp->s_size) + qp->s_cur =0 ; +break ; + +case IB_WR_ATOMIC_CMP_AND_SWP : +case IB_WR_ATOMIC_FETCH_AND_ADD : +if (wqe->wr.opcode ==IB_WR_ATOMIC_CMP_AND_SWP ) + qp->s_state =OP (COMPARE_SWAP ); +else + qp->s_state =OP (FETCH_ADD ); + ohdr->u.atomic_eth.vaddr =cpu_to_be64 ( + wqe->wr.wr.atomic.remote_addr); + ohdr->u.atomic_eth.rkey =cpu_to_be32 ( + wqe->wr.wr.atomic.rkey); + ohdr->u.atomic_eth.swap_data =cpu_to_be64 ( + wqe->wr.wr.atomic.swap); + ohdr->u.atomic_eth.compare_data =cpu_to_be64 ( + wqe->wr.wr.atomic.compare_add); + hwords +=sizeof (struct ib_atomic_eth ) /4 ; +if (newreq) { + qp->s_lsn++; + wqe->lpsn = wqe->psn; + } +if (++qp->s_cur == qp->s_size) + qp->s_cur =0 ; + ss =NULL ; + len =0 ; +break ; + +default : + goto done; + } +if (newreq) { + qp->s_tail++; +if (qp->s_tail >= qp->s_size) + qp->s_tail =0 ; + } + bth2 |= qp->s_psn++ &IPS_PSN_MASK ; +if ((int )(qp->s_psn - qp->s_next_psn) >0 ) + qp->s_next_psn = qp->s_psn; +spin_lock (&dev->pending_lock); +if (qp->timerwait.next ==LIST_POISON1 ) +list_add_tail (&qp->timerwait, + &dev->pending[dev->pending_index]); +spin_unlock (&dev->pending_lock); +break ; + +case OP (RDMA_READ_RESPONSE_FIRST ): +/* +* This case can only happen if a send is restarted. See +* ipath_restart_rc(). +*/ +ipath_init_restart (qp, wqe); +/* FALLTHROUGH */ +case OP (SEND_FIRST ): + qp->s_state =OP (SEND_MIDDLE ); +/* FALLTHROUGH */ +case OP (SEND_MIDDLE ): + bth2 = qp->s_psn++ &IPS_PSN_MASK ; +if ((int )(qp->s_psn - qp->s_next_psn) >0 ) + qp->s_next_psn = qp->s_psn; + ss = &qp->s_sge; + len = qp->s_len; +if (len > pmtu) { +/* +* Request an ACK every 1/2 MB to avoid retransmit +* timeouts. +*/ +if (((wqe->length - len) % (512 *1024 )) ==0 ) + bth2 |=1 <<31 ; + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_SEND ) + qp->s_state =OP (SEND_LAST ); +else { + qp->s_state =OP (SEND_LAST_WITH_IMMEDIATE ); +/* Immediate data comes after the BTH */ + ohdr->u.imm_data = wqe->wr.imm_data; + hwords +=1 ; + } +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; + bth2 |=1 <<31 ;/* Request ACK. */ + qp->s_cur++; +if (qp->s_cur >= qp->s_size) + qp->s_cur =0 ; +break ; + +case OP (RDMA_READ_RESPONSE_LAST ): +/* +* This case can only happen if a RDMA write is restarted. +* See ipath_restart_rc(). +*/ +ipath_init_restart (qp, wqe); +/* FALLTHROUGH */ +case OP (RDMA_WRITE_FIRST ): + qp->s_state =OP (RDMA_WRITE_MIDDLE ); +/* FALLTHROUGH */ +case OP (RDMA_WRITE_MIDDLE ): + bth2 = qp->s_psn++ &IPS_PSN_MASK ; +if ((int )(qp->s_psn - qp->s_next_psn) >0 ) + qp->s_next_psn = qp->s_psn; + ss = &qp->s_sge; + len = qp->s_len; +if (len > pmtu) { +/* +* Request an ACK every 1/2 MB to avoid retransmit +* timeouts. +*/ +if (((wqe->length - len) % (512 *1024 )) ==0 ) + bth2 |=1 <<31 ; + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_RDMA_WRITE ) + qp->s_state =OP (RDMA_WRITE_LAST ); +else { + qp->s_state =OP (RDMA_WRITE_LAST_WITH_IMMEDIATE ); +/* Immediate data comes after the BTH */ + ohdr->u.imm_data = wqe->wr.imm_data; + hwords +=1 ; +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; + } + bth2 |=1 <<31 ;/* Request ACK. */ + qp->s_cur++; +if (qp->s_cur >= qp->s_size) + qp->s_cur =0 ; +break ; + +case OP (RDMA_READ_RESPONSE_MIDDLE ): +/* +* This case can only happen if a RDMA read is restarted. +* See ipath_restart_rc(). +*/ +ipath_init_restart (qp, wqe); + len = ((qp->s_psn - wqe->psn) &IPS_PSN_MASK ) * pmtu; + ohdr->u.rc.reth.vaddr = +cpu_to_be64 (wqe->wr.wr.rdma.remote_addr + len); + ohdr->u.rc.reth.rkey = +cpu_to_be32 (wqe->wr.wr.rdma.rkey); + ohdr->u.rc.reth.length =cpu_to_be32 (qp->s_len); + qp->s_state =OP (RDMA_READ_REQUEST ); + hwords +=sizeof (ohdr->u.rc.reth) /4 ; + bth2 = qp->s_psn++ &IPS_PSN_MASK ; +if ((int )(qp->s_psn - qp->s_next_psn) >0 ) + qp->s_next_psn = qp->s_psn; + ss =NULL ; + len =0 ; + qp->s_cur++; +if (qp->s_cur == qp->s_size) + qp->s_cur =0 ; +break ; + +case OP (RDMA_READ_REQUEST ): +case OP (COMPARE_SWAP ): +case OP (FETCH_ADD ): +/* +* We shouldn't start anything new until this request is +* finished. The ACK will handle rescheduling us. XXX The +* number of outstanding ones is negotiated at connection +* setup time (see pg. 258,289)? XXX Also, if we support +* multiple outstanding requests, we need to check the WQE +* IB_SEND_FENCE flag and not send a new request if a RDMA +* read or atomic is pending. +*/ + goto done; + } + qp->s_len -= len; + qp->s_hdrwords = hwords; + qp->s_cur_sge = ss; + qp->s_cur_size = len; + *bth0p = bth0 | (qp->s_state <<24 ); + *bth2p = bth2; +return 1 ; + +done: +return 0 ; +} + +static inline void ipath_make_rc_grh (struct ipath_qp *qp, +struct ib_global_route *grh, +u32 nwords) +{ +struct ipath_ibdev *dev =to_idev (qp->ibqp.device); + +/* GRH header size in 32-bit words. */ + qp->s_hdrwords +=10 ; + qp->s_hdr.u.l.grh.version_tclass_flow = +cpu_to_be32 ((6 <<28 ) | + (grh->traffic_class <<20 ) | + grh->flow_label); + qp->s_hdr.u.l.grh.paylen = +cpu_to_be16 (((qp->s_hdrwords -12 ) + nwords + +SIZE_OF_CRC ) <<2 ); +/* next_hdr is defined by C8-7 in ch. 8.4.1 */ + qp->s_hdr.u.l.grh.next_hdr =0x1B ; + qp->s_hdr.u.l.grh.hop_limit = grh->hop_limit; +/* The SGID is 32-bit aligned. */ + qp->s_hdr.u.l.grh.sgid.global.subnet_prefix = dev->gid_prefix; + qp->s_hdr.u.l.grh.sgid.global.interface_id = +ipath_layer_get_guid (dev->dd); + qp->s_hdr.u.l.grh.dgid = grh->dgid; +} + +/** +* ipath_do_rc_send - perform a send on an RC QP +* @data: contains a pointer to the QP +* +* Process entries in the send work queue until credit or queue is +* exhausted. Only allow one CPU to send a packet per QP (tasklet). +* Otherwise, after we drop the QP s_lock, two threads could send +* packets out of order. +*/ +void ipath_do_rc_send (unsigned long data) +{ +struct ipath_qp *qp = (struct ipath_qp *)data; +struct ipath_ibdev *dev =to_idev (qp->ibqp.device); +unsigned long flags; +u16 lrh0; +u32 nwords; +u32 extra_bytes; +u32 bth0; +u32 bth2; +u32 pmtu =ib_mtu_enum_to_int (qp->path_mtu); +struct ipath_other_headers *ohdr; + +if (test_and_set_bit (IPATH_S_BUSY , &qp->s_flags)) + goto bail; + +if (unlikely (qp->remote_ah_attr.dlid == +ipath_layer_get_lid (dev->dd))) { +struct ib_wc wc; + +/* +* Pass in an uninitialized ib_wc to be consistent with +* other places where ipath_ruc_loopback() is called. +*/ +ipath_ruc_loopback (qp, &wc); + goto clear; + } + + ohdr = &qp->s_hdr.u.oth; +if (qp->remote_ah_attr.ah_flags &IB_AH_GRH ) + ohdr = &qp->s_hdr.u.l.oth; + +again: +/* Check for a constructed packet to be sent. */ +if (qp->s_hdrwords !=0 ) { +/* +* If no PIO bufs are available, return. An interrupt will +* call ipath_ib_piobufavail() when one is available. +*/ +_VERBS_INFO ("h %u %p\n" , qp->s_hdrwords, &qp->s_hdr); +_VERBS_INFO ("d %u %p %u %p %u %u %u %u\n" , qp->s_cur_size, + qp->s_cur_sge->sg_list, + qp->s_cur_sge->num_sge, + qp->s_cur_sge->sge.vaddr, + qp->s_cur_sge->sge.sge_length, + qp->s_cur_sge->sge.length, + qp->s_cur_sge->sge.m, + qp->s_cur_sge->sge.n); +if (ipath_verbs_send (dev->dd, qp->s_hdrwords, + (u32 *) &qp->s_hdr, qp->s_cur_size, + qp->s_cur_sge)) { +ipath_no_bufs_available (qp, dev); + goto bail; + } + dev->n_unicast_xmit++; +/* Record that we sent the packet and s_hdr is empty. */ + qp->s_hdrwords =0 ; + } + +/* +* The lock is needed to synchronize between setting +* qp->s_ack_state, resend timer, and post_send(). +*/ +spin_lock_irqsave (&qp->s_lock, flags); + +/* Sending responses has higher priority over sending requests. */ +if (qp->s_ack_state !=OP (ACKNOWLEDGE ) && + (bth0 =ipath_make_rc_ack (qp, ohdr, pmtu)) !=0 ) + bth2 = qp->s_ack_psn++ &IPS_PSN_MASK ; +else if (!ipath_make_rc_req (qp, ohdr, pmtu, &bth0, &bth2)) + goto done; + +spin_unlock_irqrestore (&qp->s_lock, flags); + +/* Construct the header. */ + extra_bytes = (4 - qp->s_cur_size) &3 ; + nwords = (qp->s_cur_size + extra_bytes) >>2 ; + lrh0 =IPS_LRH_BTH ; +if (unlikely (qp->remote_ah_attr.ah_flags &IB_AH_GRH )) { +ipath_make_rc_grh (qp, &qp->remote_ah_attr.grh, nwords); + lrh0 =IPS_LRH_GRH ; + } + lrh0 |= qp->remote_ah_attr.sl <<4 ; + qp->s_hdr.lrh[0 ] =cpu_to_be16 (lrh0); + qp->s_hdr.lrh[1 ] =cpu_to_be16 (qp->remote_ah_attr.dlid); + qp->s_hdr.lrh[2 ] =cpu_to_be16 (qp->s_hdrwords + nwords + +SIZE_OF_CRC ); + qp->s_hdr.lrh[3 ] =cpu_to_be16 (ipath_layer_get_lid (dev->dd)); + bth0 |=ipath_layer_get_pkey (dev->dd, qp->s_pkey_index); + bth0 |= extra_bytes <<20 ; + ohdr->bth[0 ] =cpu_to_be32 (bth0); + ohdr->bth[1 ] =cpu_to_be32 (qp->remote_qpn); + ohdr->bth[2 ] =cpu_to_be32 (bth2); + +/* Check for more work to do. */ + goto again; + +done: +spin_unlock_irqrestore (&qp->s_lock, flags); +clear: +clear_bit (IPATH_S_BUSY , &qp->s_flags); +bail: +return ; +} + +static void send_rc_ack (struct ipath_qp *qp) +{ +struct ipath_ibdev *dev =to_idev (qp->ibqp.device); +u16 lrh0; +u32 bth0; +struct ipath_other_headers *ohdr; + +/* Construct the header. */ + ohdr = &qp->s_hdr.u.oth; + lrh0 =IPS_LRH_BTH ; +/* header size in 32-bit words LRH+BTH+AETH = (8+12+4)/4. */ + qp->s_hdrwords =6 ; +if (unlikely (qp->remote_ah_attr.ah_flags &IB_AH_GRH )) { +ipath_make_rc_grh (qp, &qp->remote_ah_attr.grh,0 ); + ohdr = &qp->s_hdr.u.l.oth; + lrh0 =IPS_LRH_GRH ; + } + bth0 =ipath_layer_get_pkey (dev->dd, qp->s_pkey_index); + ohdr->u.aeth =ipath_compute_aeth (qp); +if (qp->s_ack_state >=OP (COMPARE_SWAP )) { + bth0 |=IB_OPCODE_ATOMIC_ACKNOWLEDGE <<24 ; + ohdr->u.at.atomic_ack_eth =cpu_to_be64 (qp->s_ack_atomic); + qp->s_hdrwords +=sizeof (ohdr->u.at.atomic_ack_eth) /4 ; + } +else + bth0 |=OP (ACKNOWLEDGE ) <<24 ; + lrh0 |= qp->remote_ah_attr.sl <<4 ; + qp->s_hdr.lrh[0 ] =cpu_to_be16 (lrh0); + qp->s_hdr.lrh[1 ] =cpu_to_be16 (qp->remote_ah_attr.dlid); + qp->s_hdr.lrh[2 ] =cpu_to_be16 (qp->s_hdrwords +SIZE_OF_CRC ); + qp->s_hdr.lrh[3 ] =cpu_to_be16 (ipath_layer_get_lid (dev->dd)); + ohdr->bth[0 ] =cpu_to_be32 (bth0); + ohdr->bth[1 ] =cpu_to_be32 (qp->remote_qpn); + ohdr->bth[2 ] =cpu_to_be32 (qp->s_ack_psn &IPS_PSN_MASK ); + +/* +* If we can send the ACK, clear the ACK state. +*/ +if (ipath_verbs_send (dev->dd, qp->s_hdrwords, (u32 *) &qp->s_hdr, +0 ,NULL ) ==0 ) { + qp->s_ack_state =OP (ACKNOWLEDGE ); + dev->n_rc_qacks++; + dev->n_unicast_xmit++; + } +} + +/** +* ipath_restart_rc - back up requester to resend the last un-ACKed request +* @qp: the QP to restart +* @psn: packet sequence number for the request +* @wc: the work completion request +* +* The QP s_lock should be held. +*/ +void ipath_restart_rc (struct ipath_qp *qp,u32 psn,struct ib_wc *wc) +{ +struct ipath_swqe *wqe =get_swqe_ptr (qp, qp->s_last); +struct ipath_ibdev *dev; +u32 n; + +/* +* If there are no requests pending, we are done. +*/ +if (ipath_cmp24 (psn, qp->s_next_psn) >=0 || + qp->s_last == qp->s_tail) + goto done; + +if (qp->s_retry ==0 ) { + wc->wr_id = wqe->wr.wr_id; + wc->status =IB_WC_RETRY_EXC_ERR ; + wc->opcode = ib_ipath_wc_opcode[wqe->wr.opcode]; + wc->vendor_err =0 ; + wc->byte_len =0 ; + wc->qp_num = qp->ibqp.qp_num; + wc->src_qp = qp->remote_qpn; + wc->pkey_index =0 ; + wc->slid = qp->remote_ah_attr.dlid; + wc->sl = qp->remote_ah_attr.sl; + wc->dlid_path_bits =0 ; + wc->port_num =0 ; +ipath_sqerror_qp (qp, wc); + goto bail; + } + qp->s_retry--; + +/* +* Remove the QP from the timeout queue. +* Note: it may already have been removed by ipath_ib_timer(). +*/ + dev =to_idev (qp->ibqp.device); +spin_lock (&dev->pending_lock); +if (qp->timerwait.next !=LIST_POISON1 ) +list_del (&qp->timerwait); +spin_unlock (&dev->pending_lock); + +if (wqe->wr.opcode ==IB_WR_RDMA_READ ) + dev->n_rc_resends++; +else + dev->n_rc_resends += (int )qp->s_psn - (int )psn; + +/* +* If we are starting the request from the beginning, let the normal +* send code handle initialization. +*/ + qp->s_cur = qp->s_last; +if (ipath_cmp24 (psn, wqe->psn) <=0 ) { + qp->s_state =OP (SEND_LAST ); + qp->s_psn = wqe->psn; + }else { + n = qp->s_cur; +for (;;) { +if (++n == qp->s_size) + n =0 ; +if (n == qp->s_tail) { +if (ipath_cmp24 (psn, qp->s_next_psn) >=0 ) { + qp->s_cur = n; + wqe =get_swqe_ptr (qp, n); + } +break ; + } + wqe =get_swqe_ptr (qp, n); +if (ipath_cmp24 (psn, wqe->psn) <0 ) +break ; + qp->s_cur = n; + } + qp->s_psn = psn; + +/* +* Reset the state to restart in the middle of a request. +* Don't change the s_sge, s_cur_sge, or s_cur_size. +* See ipath_do_rc_send(). +*/ +switch (wqe->wr.opcode) { +case IB_WR_SEND : +case IB_WR_SEND_WITH_IMM : + qp->s_state =OP (RDMA_READ_RESPONSE_FIRST ); +break ; + +case IB_WR_RDMA_WRITE : +case IB_WR_RDMA_WRITE_WITH_IMM : + qp->s_state =OP (RDMA_READ_RESPONSE_LAST ); +break ; + +case IB_WR_RDMA_READ : + qp->s_state = +OP (RDMA_READ_RESPONSE_MIDDLE ); +break ; + +default : +/* +* This case shouldn't happen since its only +* one PSN per req. +*/ + qp->s_state =OP (SEND_LAST ); + } + } + +done: +tasklet_hi_schedule (&qp->s_task); + +bail: +return ; +} + +/** +* reset_psn - reset the QP state to send starting from PSN +* @qp: the QP +* @psn: the packet sequence number to restart at +* +* This is called from ipath_rc_rcv() to process an incoming RC ACK +* for the given QP. +* Called at interrupt level with the QP s_lock held. +*/ +static void reset_psn (struct ipath_qp *qp,u32 psn) +{ +struct ipath_swqe *wqe; +u32 n; + + n = qp->s_cur; + wqe =get_swqe_ptr (qp, n); +for (;;) { +if (++n == qp->s_size) + n =0 ; +if (n == qp->s_tail) { +if (ipath_cmp24 (psn, qp->s_next_psn) >=0 ) { + qp->s_cur = n; + wqe =get_swqe_ptr (qp, n); + } +break ; + } + wqe =get_swqe_ptr (qp, n); +if (ipath_cmp24 (psn, wqe->psn) <0 ) +break ; + qp->s_cur = n; + } + qp->s_psn = psn; + +/* +* Set the state to restart in the middle of a +* request. Don't change the s_sge, s_cur_sge, or +* s_cur_size. See ipath_do_rc_send(). +*/ +switch (wqe->wr.opcode) { +case IB_WR_SEND : +case IB_WR_SEND_WITH_IMM : + qp->s_state =OP (RDMA_READ_RESPONSE_FIRST ); +break ; + +case IB_WR_RDMA_WRITE : +case IB_WR_RDMA_WRITE_WITH_IMM : + qp->s_state =OP (RDMA_READ_RESPONSE_LAST ); +break ; + +case IB_WR_RDMA_READ : + qp->s_state =OP (RDMA_READ_RESPONSE_MIDDLE ); +break ; + +default : +/* +* This case shouldn't happen since its only +* one PSN per req. +*/ + qp->s_state =OP (SEND_LAST ); + } +} + +/** +* do_rc_ack - process an incoming RC ACK +* @qp: the QP the ACK came in on +* @psn: the packet sequence number of the ACK +* @opcode: the opcode of the request that resulted in the ACK +* +* This is called from ipath_rc_rcv() to process an incoming RC ACK +* for the given QP. +* Called at interrupt level with the QP s_lock held. +* Returns 1 if OK, 0 if current operation should be aborted (NAK). +*/ +static int do_rc_ack (struct ipath_qp *qp,u32 aeth,u32 psn,int opcode) +{ +struct ipath_ibdev *dev =to_idev (qp->ibqp.device); +struct ib_wc wc; +struct ipath_swqe *wqe; +int ret =0 ; + +/* +* Remove the QP from the timeout queue (or RNR timeout queue). +* If ipath_ib_timer() has already removed it, +* it's OK since we hold the QP s_lock and ipath_restart_rc() +* just won't find anything to restart if we ACK everything. +*/ +spin_lock (&dev->pending_lock); +if (qp->timerwait.next !=LIST_POISON1 ) +list_del (&qp->timerwait); +spin_unlock (&dev->pending_lock); + +/* +* Note that NAKs implicitly ACK outstanding SEND and RDMA write +* requests and implicitly NAK RDMA read and atomic requests issued +* before the NAK'ed request. The MSN won't include the NAK'ed +* request but will include an ACK'ed request(s). +*/ + wqe =get_swqe_ptr (qp, qp->s_last); + +/* Nothing is pending to ACK/NAK. */ +if (qp->s_last == qp->s_tail) + goto bail; + +/* +* The MSN might be for a later WQE than the PSN indicates so +* only complete WQEs that the PSN finishes. +*/ +while (ipath_cmp24 (psn, wqe->lpsn) >=0 ) { +/* If we are ACKing a WQE, the MSN should be >= the SSN. */ +if (ipath_cmp24 (aeth, wqe->ssn) <0 ) +break ; +/* +* If this request is a RDMA read or atomic, and the ACK is +* for a later operation, this ACK NAKs the RDMA read or +* atomic. In other words, only a RDMA_READ_LAST or ONLY +* can ACK a RDMA read and likewise for atomic ops. Note +* that the NAK case can only happen if relaxed ordering is +* used and requests are sent after an RDMA read or atomic +* is sent but before the response is received. +*/ +if ((wqe->wr.opcode ==IB_WR_RDMA_READ && + opcode !=OP (RDMA_READ_RESPONSE_LAST )) || + ((wqe->wr.opcode ==IB_WR_ATOMIC_CMP_AND_SWP || + wqe->wr.opcode ==IB_WR_ATOMIC_FETCH_AND_ADD ) && + (opcode !=OP (ATOMIC_ACKNOWLEDGE ) || +ipath_cmp24 (wqe->psn, psn) !=0 ))) { +/* +* The last valid PSN seen is the previous +* request's. +*/ + qp->s_last_psn = wqe->psn -1 ; +/* Retry this request. */ +ipath_restart_rc (qp, wqe->psn, &wc); +/* +* No need to process the ACK/NAK since we are +* restarting an earlier request. +*/ + goto bail; + } +/* Post a send completion queue entry if requested. */ +if (!test_bit (IPATH_S_SIGNAL_REQ_WR , &qp->s_flags) || + (wqe->wr.send_flags &IB_SEND_SIGNALED )) { + wc.wr_id = wqe->wr.wr_id; + wc.status =IB_WC_SUCCESS ; + wc.opcode = ib_ipath_wc_opcode[wqe->wr.opcode]; + wc.vendor_err =0 ; + wc.byte_len = wqe->length; + wc.qp_num = qp->ibqp.qp_num; + wc.src_qp = qp->remote_qpn; + wc.pkey_index =0 ; + wc.slid = qp->remote_ah_attr.dlid; + wc.sl = qp->remote_ah_attr.sl; + wc.dlid_path_bits =0 ; + wc.port_num =0 ; +ipath_cq_enter (to_icq (qp->ibqp.send_cq), &wc,0 ); + } + qp->s_retry = qp->s_retry_cnt; +/* +* If we are completing a request which is in the process of +* being resent, we can stop resending it since we know the +* responder has already seen it. +*/ +if (qp->s_last == qp->s_cur) { +if (++qp->s_cur >= qp->s_size) + qp->s_cur =0 ; + wqe =get_swqe_ptr (qp, qp->s_cur); + qp->s_state =OP (SEND_LAST ); + qp->s_psn = wqe->psn; + } +if (++qp->s_last >= qp->s_size) + qp->s_last =0 ; + wqe =get_swqe_ptr (qp, qp->s_last); +if (qp->s_last == qp->s_tail) +break ; + } + +switch (aeth >>29 ) { +case 0 :/* ACK */ + dev->n_rc_acks++; +/* If this is a partial ACK, reset the retransmit timer. */ +if (qp->s_last != qp->s_tail) { +spin_lock (&dev->pending_lock); +list_add_tail (&qp->timerwait, + &dev->pending[dev->pending_index]); +spin_unlock (&dev->pending_lock); + } +ipath_get_credit (qp, aeth); + qp->s_rnr_retry = qp->s_rnr_retry_cnt; + qp->s_retry = qp->s_retry_cnt; + qp->s_last_psn = psn; + ret =1 ; + goto bail; + +case 1 :/* RNR NAK */ + dev->n_rnr_naks++; +if (qp->s_rnr_retry ==0 ) { +if (qp->s_last == qp->s_tail) + goto bail; + + wc.status =IB_WC_RNR_RETRY_EXC_ERR ; + goto class_b; + } +if (qp->s_rnr_retry_cnt <7 ) + qp->s_rnr_retry--; +if (qp->s_last == qp->s_tail) + goto bail; + +/* The last valid PSN seen is the previous request's. */ + qp->s_last_psn = wqe->psn -1 ; + + dev->n_rc_resends += (int )qp->s_psn - (int )psn; + +/* +* If we are starting the request from the beginning, let +* the normal send code handle initialization. +*/ + qp->s_cur = qp->s_last; + wqe =get_swqe_ptr (qp, qp->s_cur); +if (ipath_cmp24 (psn, wqe->psn) <=0 ) { + qp->s_state =OP (SEND_LAST ); + qp->s_psn = wqe->psn; + }else +reset_psn (qp, psn); + + qp->s_rnr_timeout = + ib_ipath_rnr_table[(aeth >>IPS_AETH_CREDIT_SHIFT ) & +IPS_AETH_CREDIT_MASK ]; +ipath_insert_rnr_queue (qp); + goto bail; + +case 3 :/* NAK */ +/* The last valid PSN seen is the previous request's. */ +if (qp->s_last != qp->s_tail) + qp->s_last_psn = wqe->psn -1 ; +switch ((aeth >>IPS_AETH_CREDIT_SHIFT ) & +IPS_AETH_CREDIT_MASK ) { +case 0 :/* PSN sequence error */ + dev->n_seq_naks++; +/* +* Back up to the responder's expected PSN. XXX +* Note that we might get a NAK in the middle of an +* RDMA READ response which terminates the RDMA +* READ. +*/ +if (qp->s_last == qp->s_tail) +break ; + +if (ipath_cmp24 (psn, wqe->psn) <0 ) +break ; + +/* Retry the request. */ +ipath_restart_rc (qp, psn, &wc); +break ; + +case 1 :/* Invalid Request */ + wc.status =IB_WC_REM_INV_REQ_ERR ; + dev->n_other_naks++; + goto class_b; + +case 2 :/* Remote Access Error */ + wc.status =IB_WC_REM_ACCESS_ERR ; + dev->n_other_naks++; + goto class_b; + +case 3 :/* Remote Operation Error */ + wc.status =IB_WC_REM_OP_ERR ; + dev->n_other_naks++; + class_b: + wc.wr_id = wqe->wr.wr_id; + wc.opcode = ib_ipath_wc_opcode[wqe->wr.opcode]; + wc.vendor_err =0 ; + wc.byte_len =0 ; + wc.qp_num = qp->ibqp.qp_num; + wc.src_qp = qp->remote_qpn; + wc.pkey_index =0 ; + wc.slid = qp->remote_ah_attr.dlid; + wc.sl = qp->remote_ah_attr.sl; + wc.dlid_path_bits =0 ; + wc.port_num =0 ; +ipath_sqerror_qp (qp, &wc); +break ; + +default : +/* Ignore other reserved NAK error codes */ + goto reserved; + } + qp->s_rnr_retry = qp->s_rnr_retry_cnt; + goto bail; + +default :/* 2: reserved */ + reserved: +/* Ignore reserved NAK codes. */ + goto bail; + } + +bail: +return ret; +} + +/** +* ipath_rc_rcv_resp - process an incoming RC response packet +* @dev: the device this packet came in on +* @ohdr: the other headers for this packet +* @data: the packet data +* @tlen: the packet length +* @qp: the QP for this packet +* @opcode: the opcode for this packet +* @psn: the packet sequence number for this packet +* @hdrsize: the header length +* @pmtu: the path MTU +* @header_in_data: true if part of the header data is in the data buffer +* +* This is called from ipath_rc_rcv() to process an incoming RC response +* packet for the given QP. +* Called at interrupt level. +*/ +static inline void ipath_rc_rcv_resp (struct ipath_ibdev *dev, +struct ipath_other_headers *ohdr, +void *data,u32 tlen, +struct ipath_qp *qp, +u32 opcode, +u32 psn,u32 hdrsize,u32 pmtu, +int header_in_data) +{ +unsigned long flags; +struct ib_wc wc; +int diff; +u32 pad; +u32 aeth; + +spin_lock_irqsave (&qp->s_lock, flags); + +/* Ignore invalid responses. */ +if (ipath_cmp24 (psn, qp->s_next_psn) >=0 ) + goto ack_done; + +/* Ignore duplicate responses. */ + diff =ipath_cmp24 (psn, qp->s_last_psn); +if (unlikely (diff <=0 )) { +/* Update credits for "ghost" ACKs */ +if (diff ==0 && opcode ==OP (ACKNOWLEDGE )) { +if (!header_in_data) + aeth =be32_to_cpu (ohdr->u.aeth); +else { + aeth =be32_to_cpu (((__be32 *) data)[0 ]); + data +=sizeof (__be32); + } +if ((aeth >>29 ) ==0 ) +ipath_get_credit (qp, aeth); + } + goto ack_done; + } + +switch (opcode) { +case OP (ACKNOWLEDGE ): +case OP (ATOMIC_ACKNOWLEDGE ): +case OP (RDMA_READ_RESPONSE_FIRST ): +if (!header_in_data) + aeth =be32_to_cpu (ohdr->u.aeth); +else { + aeth =be32_to_cpu (((__be32 *) data)[0 ]); + data +=sizeof (__be32); + } +if (opcode ==OP (ATOMIC_ACKNOWLEDGE )) + *(u64 *) qp->s_sge.sge.vaddr = *(u64 *) data; +if (!do_rc_ack (qp, aeth, psn, opcode) || + opcode !=OP (RDMA_READ_RESPONSE_FIRST )) + goto ack_done; + hdrsize +=4 ; +/* +* do_rc_ack() has already checked the PSN so skip +* the sequence check. +*/ + goto rdma_read; + +case OP (RDMA_READ_RESPONSE_MIDDLE ): +/* no AETH, no ACK */ +if (unlikely (ipath_cmp24 (psn, qp->s_last_psn +1 ))) { + dev->n_rdma_seq++; +ipath_restart_rc (qp, qp->s_last_psn +1 , &wc); + goto ack_done; + } + rdma_read: +if (unlikely (qp->s_state !=OP (RDMA_READ_REQUEST ))) + goto ack_done; +if (unlikely (tlen != (hdrsize + pmtu +4 ))) + goto ack_done; +if (unlikely (pmtu >= qp->s_len)) + goto ack_done; +/* We got a response so update the timeout. */ +if (unlikely (qp->s_last == qp->s_tail || +get_swqe_ptr (qp, qp->s_last)->wr.opcode != +IB_WR_RDMA_READ )) + goto ack_done; +spin_lock (&dev->pending_lock); +if (qp->s_rnr_timeout ==0 && + qp->timerwait.next !=LIST_POISON1 ) +list_move_tail (&qp->timerwait, + &dev->pending[dev->pending_index]); +spin_unlock (&dev->pending_lock); +/* +* Update the RDMA receive state but do the copy w/o holding the +* locks and blocking interrupts. XXX Yet another place that +* affects relaxed RDMA order since we don't want s_sge modified. +*/ + qp->s_len -= pmtu; + qp->s_last_psn = psn; +spin_unlock_irqrestore (&qp->s_lock, flags); +ipath_copy_sge (&qp->s_sge, data, pmtu); + goto bail; + +case OP (RDMA_READ_RESPONSE_LAST ): +/* ACKs READ req. */ +if (unlikely (ipath_cmp24 (psn, qp->s_last_psn +1 ))) { + dev->n_rdma_seq++; +ipath_restart_rc (qp, qp->s_last_psn +1 , &wc); + goto ack_done; + } +/* FALLTHROUGH */ +case OP (RDMA_READ_RESPONSE_ONLY ): +if (unlikely (qp->s_state !=OP (RDMA_READ_REQUEST ))) + goto ack_done; +/* +* Get the number of bytes the message was padded by. +*/ + pad = (be32_to_cpu (ohdr->bth[0 ]) >>20 ) &3 ; +/* +* Check that the data size is >= 1 && <= pmtu. +* Remember to account for the AETH header (4) and +* ICRC (4). +*/ +if (unlikely (tlen <= (hdrsize + pad +8 ))) { +/* +* XXX Need to generate an error CQ +* entry. +*/ + goto ack_done; + } + tlen -= hdrsize + pad +8 ; +if (unlikely (tlen != qp->s_len)) { +/* +* XXX Need to generate an error CQ +* entry. +*/ + goto ack_done; + } +if (!header_in_data) + aeth =be32_to_cpu (ohdr->u.aeth); +else { + aeth =be32_to_cpu (((__be32 *) data)[0 ]); + data +=sizeof (__be32); + } +ipath_copy_sge (&qp->s_sge, data, tlen); +if (do_rc_ack (qp, aeth, psn,OP (RDMA_READ_RESPONSE_LAST ))) { +/* +* Change the state so we contimue +* processing new requests. +*/ + qp->s_state =OP (SEND_LAST ); + } + goto ack_done; + } + +ack_done: +spin_unlock_irqrestore (&qp->s_lock, flags); +bail: +return ; +} + +/** +* ipath_rc_rcv_error - process an incoming duplicate or error RC packet +* @dev: the device this packet came in on +* @ohdr: the other headers for this packet +* @data: the packet data +* @qp: the QP for this packet +* @opcode: the opcode for this packet +* @psn: the packet sequence number for this packet +* @diff: the difference between the PSN and the expected PSN +* @header_in_data: true if part of the header data is in the data buffer +* +* This is called from ipath_rc_rcv() to process an unexpected +* incoming RC packet for the given QP. +* Called at interrupt level. +* Return 1 if no more processing is needed; otherwise return 0 to +* schedule a response to be sent and the s_lock unlocked. +*/ +static inline int ipath_rc_rcv_error (struct ipath_ibdev *dev, +struct ipath_other_headers *ohdr, +void *data, +struct ipath_qp *qp, +u32 opcode, +u32 psn, +int diff, +int header_in_data) +{ +struct ib_reth *reth; + +if (diff >0 ) { +/* +* Packet sequence error. +* A NAK will ACK earlier sends and RDMA writes. +* Don't queue the NAK if a RDMA read, atomic, or +* NAK is pending though. +*/ +spin_lock (&qp->s_lock); +if ((qp->s_ack_state >=OP (RDMA_READ_REQUEST ) && + qp->s_ack_state !=IB_OPCODE_ACKNOWLEDGE ) || + qp->s_nak_state !=0 ) { +spin_unlock (&qp->s_lock); + goto done; + } + qp->s_ack_state =OP (SEND_ONLY ); + qp->s_nak_state =IB_NAK_PSN_ERROR ; +/* Use the expected PSN. */ + qp->s_ack_psn = qp->r_psn; + goto resched; + } + +/* +* Handle a duplicate request. Don't re-execute SEND, RDMA +* write or atomic op. Don't NAK errors, just silently drop +* the duplicate request. Note that r_sge, r_len, and +* r_rcv_len may be in use so don't modify them. +* +* We are supposed to ACK the earliest duplicate PSN but we +* can coalesce an outstanding duplicate ACK. We have to +* send the earliest so that RDMA reads can be restarted at +* the requester's expected PSN. +*/ +spin_lock (&qp->s_lock); +if (qp->s_ack_state !=IB_OPCODE_ACKNOWLEDGE && +ipath_cmp24 (psn, qp->s_ack_psn) >=0 ) { +if (qp->s_ack_state <IB_OPCODE_RDMA_READ_REQUEST ) + qp->s_ack_psn = psn; +spin_unlock (&qp->s_lock); + goto done; + } +switch (opcode) { +case OP (RDMA_READ_REQUEST ): +/* +* We have to be careful to not change s_rdma_sge +* while ipath_do_rc_send() is using it and not +* holding the s_lock. +*/ +if (qp->s_ack_state !=OP (ACKNOWLEDGE ) && + qp->s_ack_state >=IB_OPCODE_RDMA_READ_REQUEST ) { +spin_unlock (&qp->s_lock); + dev->n_rdma_dup_busy++; + goto done; + } +/* RETH comes after BTH */ +if (!header_in_data) + reth = &ohdr->u.rc.reth; +else { + reth = (struct ib_reth *)data; + data +=sizeof (*reth); + } + qp->s_rdma_len =be32_to_cpu (reth->length); +if (qp->s_rdma_len !=0 ) { +u32 rkey =be32_to_cpu (reth->rkey); +u64 vaddr =be64_to_cpu (reth->vaddr); +int ok; + +/* +* Address range must be a subset of the original +* request and start on pmtu boundaries. +*/ + ok =ipath_rkey_ok (dev, &qp->s_rdma_sge, + qp->s_rdma_len, vaddr, rkey, +IB_ACCESS_REMOTE_READ ); +if (unlikely (!ok)) + goto done; + }else { + qp->s_rdma_sge.sg_list =NULL ; + qp->s_rdma_sge.num_sge =0 ; + qp->s_rdma_sge.sge.mr =NULL ; + qp->s_rdma_sge.sge.vaddr =NULL ; + qp->s_rdma_sge.sge.length =0 ; + qp->s_rdma_sge.sge.sge_length =0 ; + } +break ; + +case OP (COMPARE_SWAP ): +case OP (FETCH_ADD ): +/* +* Check for the PSN of the last atomic operations +* performed and resend the result if found. +*/ +if ((psn &IPS_PSN_MASK ) != qp->r_atomic_psn) { +spin_unlock (&qp->s_lock); + goto done; + } + qp->s_ack_atomic = qp->r_atomic_data; +break ; + } + qp->s_ack_state = opcode; + qp->s_nak_state =0 ; + qp->s_ack_psn = psn; +resched: +return 0 ; + +done: +return 1 ; +} + +/** +* ipath_rc_rcv - process an incoming RC packet +* @dev: the device this packet came in on +* @hdr: the header of this packet +* @has_grh: true if the header has a GRH +* @data: the packet data +* @tlen: the packet length +* @qp: the QP for this packet +* +* This is called from ipath_qp_rcv() to process an incoming RC packet +* for the given QP. +* Called at interrupt level. +*/ +void ipath_rc_rcv (struct ipath_ibdev *dev,struct ipath_ib_header *hdr, +int has_grh,void *data,u32 tlen,struct ipath_qp *qp) +{ +struct ipath_other_headers *ohdr; +u32 opcode; +u32 hdrsize; +u32 psn; +u32 pad; +unsigned long flags; +struct ib_wc wc; +u32 pmtu =ib_mtu_enum_to_int (qp->path_mtu); +int diff; +struct ib_reth *reth; +int header_in_data; + +/* Check for GRH */ +if (!has_grh) { + ohdr = &hdr->u.oth; + hdrsize =8 +12 ;/* LRH + BTH */ + psn =be32_to_cpu (ohdr->bth[2 ]); + header_in_data =0 ; + }else { + ohdr = &hdr->u.l.oth; + hdrsize =8 +40 +12 ;/* LRH + GRH + BTH */ +/* +* The header with GRH is 60 bytes and the core driver sets +* the eager header buffer size to 56 bytes so the last 4 +* bytes of the BTH header (PSN) is in the data buffer. +*/ + header_in_data = +ipath_layer_get_rcvhdrentsize (dev->dd) ==16 ; +if (header_in_data) { + psn =be32_to_cpu (((__be32 *) data)[0 ]); + data +=sizeof (__be32); + }else + psn =be32_to_cpu (ohdr->bth[2 ]); + } +/* +* The opcode is in the low byte when its in network order +* (top byte when in host order). +*/ + opcode =be32_to_cpu (ohdr->bth[0 ]) >>24 ; + +/* +* Process responses (ACKs) before anything else. Note that the +* packet sequence number will be for something in the send work +* queue rather than the expected receive packet sequence number. +* In other words, this QP is the requester. +*/ +if (opcode >=OP (RDMA_READ_RESPONSE_FIRST ) && + opcode <=OP (ATOMIC_ACKNOWLEDGE )) { +ipath_rc_rcv_resp (dev, ohdr, data, tlen, qp, opcode, psn, + hdrsize, pmtu, header_in_data); + goto bail; + } + +spin_lock_irqsave (&qp->r_rq.lock, flags); + +/* Compute 24 bits worth of difference. */ + diff =ipath_cmp24 (psn, qp->r_psn); +if (unlikely (diff)) { +if (ipath_rc_rcv_error (dev, ohdr, data, qp, opcode, + psn, diff, header_in_data)) + goto done; + goto resched; + } + +/* Check for opcode sequence errors. */ +switch (qp->r_state) { +case OP (SEND_FIRST ): +case OP (SEND_MIDDLE ): +if (opcode ==OP (SEND_MIDDLE ) || + opcode ==OP (SEND_LAST ) || + opcode ==OP (SEND_LAST_WITH_IMMEDIATE )) +break ; + nack_inv: +/* +* A NAK will ACK earlier sends and RDMA writes. Don't queue the +* NAK if a RDMA read, atomic, or NAK is pending though. +*/ +spin_lock (&qp->s_lock); +if (qp->s_ack_state >=OP (RDMA_READ_REQUEST ) && + qp->s_ack_state !=IB_OPCODE_ACKNOWLEDGE ) { +spin_unlock (&qp->s_lock); + goto done; + } +/* XXX Flush WQEs */ + qp->state =IB_QPS_ERR ; + qp->s_ack_state =OP (SEND_ONLY ); + qp->s_nak_state =IB_NAK_INVALID_REQUEST ; + qp->s_ack_psn = qp->r_psn; + goto resched; + +case OP (RDMA_WRITE_FIRST ): +case OP (RDMA_WRITE_MIDDLE ): +if (opcode ==OP (RDMA_WRITE_MIDDLE ) || + opcode ==OP (RDMA_WRITE_LAST ) || + opcode ==OP (RDMA_WRITE_LAST_WITH_IMMEDIATE )) +break ; + goto nack_inv; + +case OP (RDMA_READ_REQUEST ): +case OP (COMPARE_SWAP ): +case OP (FETCH_ADD ): +/* +* Drop all new requests until a response has been sent. A +* new request then ACKs the RDMA response we sent. Relaxed +* ordering would allow new requests to be processed but we +* would need to keep a queue of rwqe's for all that are in +* progress. Note that we can't RNR NAK this request since +* the RDMA READ or atomic response is already queued to be +* sent (unless we implement a response send queue). +*/ + goto done; + +default : +if (opcode ==OP (SEND_MIDDLE ) || + opcode ==OP (SEND_LAST ) || + opcode ==OP (SEND_LAST_WITH_IMMEDIATE ) || + opcode ==OP (RDMA_WRITE_MIDDLE ) || + opcode ==OP (RDMA_WRITE_LAST ) || + opcode ==OP (RDMA_WRITE_LAST_WITH_IMMEDIATE )) + goto nack_inv; +break ; + } + + wc.imm_data =0 ; + wc.wc_flags =0 ; + +/* OK, process the packet. */ +switch (opcode) { +case OP (SEND_FIRST ): +if (!ipath_get_rwqe (qp,0 )) { + rnr_nak: +/* +* A RNR NAK will ACK earlier sends and RDMA writes. +* Don't queue the NAK if a RDMA read or atomic +* is pending though. +*/ +spin_lock (&qp->s_lock); +if (qp->s_ack_state >= +OP (RDMA_READ_REQUEST ) && + qp->s_ack_state !=IB_OPCODE_ACKNOWLEDGE ) { +spin_unlock (&qp->s_lock); + goto done; + } + qp->s_ack_state =OP (SEND_ONLY ); + qp->s_nak_state =IB_RNR_NAK | qp->s_min_rnr_timer; + qp->s_ack_psn = qp->r_psn; + goto resched; + } + qp->r_rcv_len =0 ; +/* FALLTHROUGH */ +case OP (SEND_MIDDLE ): +case OP (RDMA_WRITE_MIDDLE ): + send_middle: +/* Check for invalid length PMTU or posted rwqe len. */ +if (unlikely (tlen != (hdrsize + pmtu +4 ))) + goto nack_inv; + qp->r_rcv_len += pmtu; +if (unlikely (qp->r_rcv_len > qp->r_len)) + goto nack_inv; +ipath_copy_sge (&qp->r_sge, data, pmtu); +break ; + +case OP (RDMA_WRITE_LAST_WITH_IMMEDIATE ): +/* consume RWQE */ +if (!ipath_get_rwqe (qp,1 )) + goto rnr_nak; + goto send_last_imm; + +case OP (SEND_ONLY ): +case OP (SEND_ONLY_WITH_IMMEDIATE ): +if (!ipath_get_rwqe (qp,0 )) + goto rnr_nak; + qp->r_rcv_len =0 ; +if (opcode ==OP (SEND_ONLY )) + goto send_last; +/* FALLTHROUGH */ +case OP (SEND_LAST_WITH_IMMEDIATE ): + send_last_imm: +if (header_in_data) { + wc.imm_data = *(__be32 *) data; + data +=sizeof (__be32); + }else { +/* Immediate data comes after BTH */ + wc.imm_data = ohdr->u.imm_data; + } + hdrsize +=4 ; + wc.wc_flags =IB_WC_WITH_IMM ; +/* FALLTHROUGH */ +case OP (SEND_LAST ): +case OP (RDMA_WRITE_LAST ): + send_last: +/* Get the number of bytes the message was padded by. */ + pad = (be32_to_cpu (ohdr->bth[0 ]) >>20 ) &3 ; +/* Check for invalid length. */ +/* XXX LAST len should be >= 1 */ +if (unlikely (tlen < (hdrsize + pad +4 ))) + goto nack_inv; +/* Don't count the CRC. */ + tlen -= (hdrsize + pad +4 ); + wc.byte_len = tlen + qp->r_rcv_len; +if (unlikely (wc.byte_len > qp->r_len)) + goto nack_inv; +ipath_copy_sge (&qp->r_sge, data, tlen); +atomic_inc (&qp->msn); +if (opcode ==OP (RDMA_WRITE_LAST ) || + opcode ==OP (RDMA_WRITE_ONLY )) +break ; + wc.wr_id = qp->r_wr_id; + wc.status =IB_WC_SUCCESS ; + wc.opcode =IB_WC_RECV ; + wc.vendor_err =0 ; + wc.qp_num = qp->ibqp.qp_num; + wc.src_qp = qp->remote_qpn; + wc.pkey_index =0 ; + wc.slid = qp->remote_ah_attr.dlid; + wc.sl = qp->remote_ah_attr.sl; + wc.dlid_path_bits =0 ; + wc.port_num =0 ; +/* Signal completion event if the solicited bit is set. */ +ipath_cq_enter (to_icq (qp->ibqp.recv_cq), &wc, + (ohdr->bth[0 ] & +__constant_cpu_to_be32 (1 <<23 )) !=0 ); +break ; + +case OP (RDMA_WRITE_FIRST ): +case OP (RDMA_WRITE_ONLY ): +case OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE ): +/* consume RWQE */ +/* RETH comes after BTH */ +if (!header_in_data) + reth = &ohdr->u.rc.reth; +else { + reth = (struct ib_reth *)data; + data +=sizeof (*reth); + } + hdrsize +=sizeof (*reth); + qp->r_len =be32_to_cpu (reth->length); + qp->r_rcv_len =0 ; +if (qp->r_len !=0 ) { +u32 rkey =be32_to_cpu (reth->rkey); +u64 vaddr =be64_to_cpu (reth->vaddr); +int ok; + +/* Check rkey & NAK */ + ok =ipath_rkey_ok (dev, &qp->r_sge, + qp->r_len, vaddr, rkey, +IB_ACCESS_REMOTE_WRITE ); +if (unlikely (!ok)) { + nack_acc: +/* +* A NAK will ACK earlier sends and RDMA +* writes. Don't queue the NAK if a RDMA +* read, atomic, or NAK is pending though. +*/ +spin_lock (&qp->s_lock); +if (qp->s_ack_state >= +OP (RDMA_READ_REQUEST ) && + qp->s_ack_state != +IB_OPCODE_ACKNOWLEDGE ) { +spin_unlock (&qp->s_lock); + goto done; + } +/* XXX Flush WQEs */ + qp->state =IB_QPS_ERR ; + qp->s_ack_state =OP (RDMA_WRITE_ONLY ); + qp->s_nak_state = +IB_NAK_REMOTE_ACCESS_ERROR ; + qp->s_ack_psn = qp->r_psn; + goto resched; + } + }else { + qp->r_sge.sg_list =NULL ; + qp->r_sge.sge.mr =NULL ; + qp->r_sge.sge.vaddr =NULL ; + qp->r_sge.sge.length =0 ; + qp->r_sge.sge.sge_length =0 ; + } +if (unlikely (!(qp->qp_access_flags & +IB_ACCESS_REMOTE_WRITE ))) + goto nack_acc; +if (opcode ==OP (RDMA_WRITE_FIRST )) + goto send_middle; +else if (opcode ==OP (RDMA_WRITE_ONLY )) + goto send_last; +if (!ipath_get_rwqe (qp,1 )) + goto rnr_nak; + goto send_last_imm; + +case OP (RDMA_READ_REQUEST ): +/* RETH comes after BTH */ +if (!header_in_data) + reth = &ohdr->u.rc.reth; +else { + reth = (struct ib_reth *)data; + data +=sizeof (*reth); + } +spin_lock (&qp->s_lock); +if (qp->s_ack_state !=OP (ACKNOWLEDGE ) && + qp->s_ack_state >=IB_OPCODE_RDMA_READ_REQUEST ) { +spin_unlock (&qp->s_lock); + goto done; + } + qp->s_rdma_len =be32_to_cpu (reth->length); +if (qp->s_rdma_len !=0 ) { +u32 rkey =be32_to_cpu (reth->rkey); +u64 vaddr =be64_to_cpu (reth->vaddr); +int ok; + +/* Check rkey & NAK */ + ok =ipath_rkey_ok (dev, &qp->s_rdma_sge, + qp->s_rdma_len, vaddr, rkey, +IB_ACCESS_REMOTE_READ ); +if (unlikely (!ok)) { +spin_unlock (&qp->s_lock); + goto nack_acc; + } +/* +* Update the next expected PSN. We add 1 later +* below, so only add the remainder here. +*/ +if (qp->s_rdma_len > pmtu) + qp->r_psn += (qp->s_rdma_len -1 ) / pmtu; + }else { + qp->s_rdma_sge.sg_list =NULL ; + qp->s_rdma_sge.num_sge =0 ; + qp->s_rdma_sge.sge.mr =NULL ; + qp->s_rdma_sge.sge.vaddr =NULL ; + qp->s_rdma_sge.sge.length =0 ; + qp->s_rdma_sge.sge.sge_length =0 ; + } +if (unlikely (!(qp->qp_access_flags & +IB_ACCESS_REMOTE_READ ))) + goto nack_acc; +/* +* We need to increment the MSN here instead of when we +* finish sending the result since a duplicate request would +* increment it more than once. +*/ +atomic_inc (&qp->msn); + qp->s_ack_state = opcode; + qp->s_nak_state =0 ; + qp->s_ack_psn = psn; + qp->r_psn++; + qp->r_state = opcode; + goto rdmadone; + +case OP (COMPARE_SWAP ): +case OP (FETCH_ADD ): { +struct ib_atomic_eth *ateth; +u64 vaddr; +u64 sdata; +u32 rkey; + +if (!header_in_data) + ateth = &ohdr->u.atomic_eth; +else { + ateth = (struct ib_atomic_eth *)data; + data +=sizeof (*ateth); + } + vaddr =be64_to_cpu (ateth->vaddr); +if (unlikely (vaddr & (sizeof (u64) -1 ))) + goto nack_inv; + rkey =be32_to_cpu (ateth->rkey); +/* Check rkey & NAK */ +if (unlikely (!ipath_rkey_ok (dev, &qp->r_sge, +sizeof (u64), vaddr, rkey, +IB_ACCESS_REMOTE_ATOMIC ))) + goto nack_acc; +if (unlikely (!(qp->qp_access_flags & +IB_ACCESS_REMOTE_ATOMIC ))) + goto nack_acc; +/* Perform atomic OP and save result. */ + sdata =be64_to_cpu (ateth->swap_data); +spin_lock (&dev->pending_lock); + qp->r_atomic_data = *(u64 *) qp->r_sge.sge.vaddr; +if (opcode ==OP (FETCH_ADD )) + *(u64 *) qp->r_sge.sge.vaddr = + qp->r_atomic_data + sdata; +else if (qp->r_atomic_data == +be64_to_cpu (ateth->compare_data)) + *(u64 *) qp->r_sge.sge.vaddr = sdata; +spin_unlock (&dev->pending_lock); +atomic_inc (&qp->msn); + qp->r_atomic_psn = psn &IPS_PSN_MASK ; + psn |=1 <<31 ; +break ; + } + +default : +/* Drop packet for unknown opcodes. */ + goto done; + } + qp->r_psn++; + qp->r_state = opcode; +/* Send an ACK if requested or required. */ +if (psn & (1 <<31 )) { +/* +* Coalesce ACKs unless there is a RDMA READ or +* ATOMIC pending. +*/ +spin_lock (&qp->s_lock); +if (qp->s_ack_state ==OP (ACKNOWLEDGE ) || + qp->s_ack_state <IB_OPCODE_RDMA_READ_REQUEST ) { + qp->s_ack_state = opcode; + qp->s_nak_state =0 ; + qp->s_ack_psn = psn; + qp->s_ack_atomic = qp->r_atomic_data; + goto resched; + } +spin_unlock (&qp->s_lock); + } +done: +spin_unlock_irqrestore (&qp->r_rq.lock, flags); + goto bail; + +resched: +/* +* Try to send ACK right away but not if ipath_do_rc_send() is +* active. +*/ +if (qp->s_hdrwords ==0 && + (qp->s_ack_state <IB_OPCODE_RDMA_READ_REQUEST || + qp->s_ack_state >=IB_OPCODE_COMPARE_SWAP )) +send_rc_ack (qp); + +rdmadone: +spin_unlock (&qp->s_lock); +spin_unlock_irqrestore (&qp->r_rq.lock, flags); + +/* Call ipath_do_rc_send() in another thread. */ +tasklet_hi_schedule (&qp->s_task); + +bail: +return ; +}
Re: [PATCH 12 of 16] ipath - infiniband RC protocol support
Hi!
drivers/infiniband/hw/ipath/ipath_rc.c line 37
Quoted 5 lines
This is an implementation of the Infiniband RC ("reliable connection") protocol.
drivers/infiniband/hw/ipath/ipath_rc.c new file +2
-0+/* cut down ridiculously long IB macro names */ +#define OP (x) IB_OPCODE_RC_##x
Heh... what about fixing those names in the first place?
Quoted 7 lines
drivers/infiniband/hw/ipath/ipath_rc.c new file +7
-0+/* GRH header size in 32-bit words. */ + qp->s_hdrwords +=10 ; + qp->s_hdr.u.l.grh.version_tclass_flow = +cpu_to_be32 ((6 <<28 ) | + (grh->traffic_class <<20 ) | + grh->flow_label); + qp->s_hdr.u.l.grh.paylen =
drivers/infiniband/hw/ipath/ipath_rc.c line 521
Quoted 10 lines
drivers/infiniband/hw/ipath/ipath_rc.c new file +10
-0+cpu_to_be16 (((qp->s_hdrwords -12 ) + nwords + +SIZE_OF_CRC ) <<2 ); +/* next_hdr is defined by C8-7 in ch. 8.4.1 */ + qp->s_hdr.u.l.grh.next_hdr =0x1B ; + qp->s_hdr.u.l.grh.hop_limit = grh->hop_limit; +/* The SGID is 32-bit aligned. */ + qp->s_hdr.u.l.grh.sgid.global.subnet_prefix = dev->gid_prefix; + qp->s_hdr.u.l.grh.sgid.global.interface_id = +ipath_layer_get_guid (dev->dd); + qp->s_hdr.u.l.grh.dgid = grh->dgid;
Don't know about you, but it looks like perl code to me. qp->s_hdr.u.l.grh.next_hdr ?
drivers/infiniband/hw/ipath/ipath_rc.c line 573
Quoted 8 lines
drivers/infiniband/hw/ipath/ipath_rc.c new file +8
-0+/* Check for a constructed packet to be sent. */ +if (qp->s_hdrwords !=0 ) { +/* +* If no PIO bufs are available, return. An interrupt will +* call ipath_ib_piobufavail() when one is available. +*/ +_VERBS_INFO ("h %u %p\n" , qp->s_hdrwords, &qp->s_hdr); + _VERBS_INFO("d %u %p %u %p %u %u %u %u\n", qp->s_cur_size,
Info on verbs, or verbose info? Why does it start with _ ? What is wrong with printk?
Pavel
Signature · 1 line
Picture of sleeping (Linux) penguin wanted...
PATCH 1/1 ipath - infiniband verbs support
In reply to Bryan O'SullivanThe ipath_verbs.c file implements the driver-specific components of the kernel's Infiniband verbs layer.
drivers/infiniband/hw/ipath/ipath_verbs.c new file +1222 -0
@@ -0,0 +1,1222 @@ +/* +* Copyright (c) 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include <rdma/ib_mad.h> +#include <rdma/ib_user_verbs.h> +#include <linux/utsname.h> + +#include "ipath_kernel.h" +#include "ipath_verbs.h" +#include "ips_common.h" + +/* Not static, because we don't want the compiler removing it */ +const char ipath_verbs_version[] ="ipath_verbs " IPATH_IDSTR ; + +unsigned int ib_ipath_qp_table_size =251 ; +module_param_named (qp_table_size, ib_ipath_qp_table_size, uint,S_IRUGO ); +MODULE_PARM_DESC (qp_table_size,"QP table size" ); + +unsigned int ib_ipath_lkey_table_size =12 ; +module_param_named (lkey_table_size, ib_ipath_lkey_table_size, uint, +S_IRUGO ); +MODULE_PARM_DESC (lkey_table_size, +"LKEY table size in bits (2^n, 1 <= n <= 23)" ); + +unsigned int ib_ipath_debug;/* debug mask */ +module_param_named (debug, ib_ipath_debug, uint,S_IWUSR |S_IRUGO ); +MODULE_PARM_DESC (debug,"Verbs debug mask" ); + +MODULE_LICENSE ("GPL" ); +MODULE_AUTHOR ("PathScale <[email protected]>" ); +MODULE_DESCRIPTION ("Pathscale InfiniPath driver" ); + +const int ib_ipath_state_ops[IB_QPS_ERR +1 ] = { + [IB_QPS_RESET ] =0 , + [IB_QPS_INIT ] =IPATH_POST_RECV_OK , + [IB_QPS_RTR ] =IPATH_POST_RECV_OK |IPATH_PROCESS_RECV_OK , + [IB_QPS_RTS ] =IPATH_POST_RECV_OK |IPATH_PROCESS_RECV_OK | +IPATH_POST_SEND_OK |IPATH_PROCESS_SEND_OK , + [IB_QPS_SQD ] =IPATH_POST_RECV_OK |IPATH_PROCESS_RECV_OK | +IPATH_POST_SEND_OK , + [IB_QPS_SQE ] =IPATH_POST_RECV_OK |IPATH_PROCESS_RECV_OK , + [IB_QPS_ERR ] =0 , +}; + +/* +* Translate ib_wr_opcode into ib_wc_opcode. +*/ +const enum ib_wc_opcode ib_ipath_wc_opcode[] = { + [IB_WR_RDMA_WRITE ] =IB_WC_RDMA_WRITE , + [IB_WR_RDMA_WRITE_WITH_IMM ] =IB_WC_RDMA_WRITE , + [IB_WR_SEND ] =IB_WC_SEND , + [IB_WR_SEND_WITH_IMM ] =IB_WC_SEND , + [IB_WR_RDMA_READ ] =IB_WC_RDMA_READ , + [IB_WR_ATOMIC_CMP_AND_SWP ] =IB_WC_COMP_SWAP , + [IB_WR_ATOMIC_FETCH_AND_ADD ] =IB_WC_FETCH_ADD +}; + +/* +* System image GUID. +*/ +__be64 sys_image_guid; + +/** +* ipath_copy_sge - copy data to SGE memory +* @ss: the SGE state +* @data: the data to copy +* @length: the length of the data +*/ +void ipath_copy_sge (struct ipath_sge_state *ss,void *data,u32 length) +{ +struct ipath_sge *sge = &ss->sge; + +while (length) { +u32 len = sge->length; + +BUG_ON (len ==0 ); +if (len > length) + len = length; +memcpy (sge->vaddr, data, len); + sge->vaddr += len; + sge->length -= len; + sge->sge_length -= len; +if (sge->sge_length ==0 ) { +if (--ss->num_sge) + *sge = *ss->sg_list++; + }else if (sge->length ==0 && sge->mr !=NULL ) { +if (++sge->n >=IPATH_SEGSZ ) { +if (++sge->m >= sge->mr->mapsz) +break ; + sge->n =0 ; + } + sge->vaddr = + sge->mr->map[sge->m]->segs[sge->n].vaddr; + sge->length = + sge->mr->map[sge->m]->segs[sge->n].length; + } + data += len; + length -= len; + } +} + +/** +* ipath_skip_sge - skip over SGE memory - XXX almost dup of prev func +* @ss: the SGE state +* @length: the number of bytes to skip +*/ +void ipath_skip_sge (struct ipath_sge_state *ss,u32 length) +{ +struct ipath_sge *sge = &ss->sge; + +while (length > sge->sge_length) { + length -= sge->sge_length; + ss->sge = *ss->sg_list++; + } +while (length) { +u32 len = sge->length; + +BUG_ON (len ==0 ); +if (len > length) + len = length; + sge->vaddr += len; + sge->length -= len; + sge->sge_length -= len; +if (sge->sge_length ==0 ) { +if (--ss->num_sge) + *sge = *ss->sg_list++; + }else if (sge->length ==0 && sge->mr !=NULL ) { +if (++sge->n >=IPATH_SEGSZ ) { +if (++sge->m >= sge->mr->mapsz) +break ; + sge->n =0 ; + } + sge->vaddr = + sge->mr->map[sge->m]->segs[sge->n].vaddr; + sge->length = + sge->mr->map[sge->m]->segs[sge->n].length; + } + length -= len; + } +} + +/** +* ipath_post_send - post a send on a QP +* @ibqp: the QP to post the send on +* @wr: the list of work requests to post +* @bad_wr: the first bad WR is put here +* +* This may be called from interrupt context. +*/ +static int ipath_post_send (struct ib_qp *ibqp,struct ib_send_wr *wr, +struct ib_send_wr **bad_wr) +{ +struct ipath_qp *qp =to_iqp (ibqp); +int err =0 ; + +/* Check that state is OK to post send. */ +if (!(ib_ipath_state_ops[qp->state] &IPATH_POST_SEND_OK )) { + *bad_wr = wr; + err = -EINVAL ; + goto bail; + } + +for (; wr; wr = wr->next) { +switch (qp->ibqp.qp_type) { +case IB_QPT_UC : +case IB_QPT_RC : + err =ipath_post_rc_send (qp, wr); +break ; + +case IB_QPT_SMI : +case IB_QPT_GSI : +case IB_QPT_UD : + err =ipath_post_ud_send (qp, wr); +break ; + +default : + err = -EINVAL ; + } +if (err) { + *bad_wr = wr; +break ; + } + } + +bail: +return err; +} + +/** +* ipath_post_receive - post a receive on a QP +* @ibqp: the QP to post the receive on +* @wr: the WR to post +* @bad_wr: the first bad WR is put here +* +* This may be called from interrupt context. +*/ +static int ipath_post_receive (struct ib_qp *ibqp,struct ib_recv_wr *wr, +struct ib_recv_wr **bad_wr) +{ +struct ipath_qp *qp =to_iqp (ibqp); +unsigned long flags; +int ret; + +/* Check that state is OK to post receive. */ +if (!(ib_ipath_state_ops[qp->state] &IPATH_POST_RECV_OK )) { + *bad_wr = wr; + ret = -EINVAL ; + goto bail; + } + +for (; wr; wr = wr->next) { +struct ipath_rwqe *wqe; +u32 next; +int i, j; + +if (wr->num_sge > qp->r_rq.max_sge) { + *bad_wr = wr; + ret = -ENOMEM ; + goto bail; + } + +spin_lock_irqsave (&qp->r_rq.lock, flags); + next = qp->r_rq.head +1 ; +if (next >= qp->r_rq.size) + next =0 ; +if (next == qp->r_rq.tail) { +spin_unlock_irqrestore (&qp->r_rq.lock, flags); + *bad_wr = wr; + ret = -ENOMEM ; + goto bail; + } + + wqe =get_rwqe_ptr (&qp->r_rq, qp->r_rq.head); + wqe->wr_id = wr->wr_id; + wqe->sg_list[0 ].mr =NULL ; + wqe->sg_list[0 ].vaddr =NULL ; + wqe->sg_list[0 ].length =0 ; + wqe->sg_list[0 ].sge_length =0 ; + wqe->length =0 ; +for (i =0 , j =0 ; i < wr->num_sge; i++) { +/* Check LKEY */ +if (to_ipd (qp->ibqp.pd)->user && + wr->sg_list[i].lkey ==0 ) { +spin_unlock_irqrestore (&qp->r_rq.lock, + flags); + *bad_wr = wr; + ret = -EINVAL ; + goto bail; + } +if (wr->sg_list[i].length ==0 ) +continue ; +if (!ipath_lkey_ok ( + &to_idev (qp->ibqp.device)->lk_table, + &wqe->sg_list[j], &wr->sg_list[i], +IB_ACCESS_LOCAL_WRITE )) { +spin_unlock_irqrestore (&qp->r_rq.lock, + flags); + *bad_wr = wr; + ret = -EINVAL ; + goto bail; + } + wqe->length += wr->sg_list[i].length; + j++; + } + wqe->num_sge = j; + qp->r_rq.head = next; +spin_unlock_irqrestore (&qp->r_rq.lock, flags); + } + ret =0 ; + +bail: +return ret; +} + +/** +* ipath_qp_rcv - processing an incoming packet on a QP +* @dev: the device the packet came on +* @hdr: the packet header +* @has_grh: true if the packet has a GRH +* @data: the packet data +* @tlen: the packet length +* @qp: the QP the packet came on +* +* This is called from ipath_ib_rcv() to process an incoming packet +* for the given QP. +* Called at interrupt level. +*/ +static void ipath_qp_rcv (struct ipath_ibdev *dev, +struct ipath_ib_header *hdr,int has_grh, +void *data,u32 tlen,struct ipath_qp *qp) +{ +/* Check for valid receive state. */ +if (!(ib_ipath_state_ops[qp->state] &IPATH_PROCESS_RECV_OK )) { + dev->n_pkt_drops++; +return ; + } + +switch (qp->ibqp.qp_type) { +case IB_QPT_SMI : +case IB_QPT_GSI : +case IB_QPT_UD : +ipath_ud_rcv (dev, hdr, has_grh, data, tlen, qp); +break ; + +case IB_QPT_RC : +ipath_rc_rcv (dev, hdr, has_grh, data, tlen, qp); +break ; + +case IB_QPT_UC : +ipath_uc_rcv (dev, hdr, has_grh, data, tlen, qp); +break ; + +default : +break ; + } +} + +/** +* ipath_ib_rcv - process and incoming packet +* @arg: the device pointer +* @rhdr: the header of the packet +* @data: the packet data +* @tlen: the packet length +* +* This is called from ipath_kreceive() to process an incoming packet at +* interrupt level. Tlen is the length of the header + data + CRC in bytes. +*/ +static void ipath_ib_rcv (void *arg,void *rhdr,void *data,u32 tlen) +{ +struct ipath_ibdev *dev = (struct ipath_ibdev *) arg; +struct ipath_ib_header *hdr = rhdr; +struct ipath_other_headers *ohdr; +struct ipath_qp *qp; +u32 qp_num; +int lnh; +u8 opcode; +u16 lid; + +if (unlikely (dev ==NULL )) + goto bail; + +if (unlikely (tlen <24 )) {/* LRH+BTH+CRC */ + dev->rcv_errors++; + goto bail; + } + +/* Check for a valid destination LID (see ch. 7.11.1). */ + lid =be16_to_cpu (hdr->lrh[1 ]); +if (lid <IPS_MULTICAST_LID_BASE ) { + lid &= ~((1 << (dev->mkeyprot_resv_lmc &7 )) -1 ); +if (unlikely (lid !=ipath_layer_get_lid (dev->dd))) { + dev->rcv_errors++; + goto bail; + } + } + +/* Check for GRH */ + lnh =be16_to_cpu (hdr->lrh[0 ]) &3 ; +if (lnh ==IPS_LRH_BTH ) + ohdr = &hdr->u.oth; +else if (lnh ==IPS_LRH_GRH ) + ohdr = &hdr->u.l.oth; +else { + dev->rcv_errors++; + goto bail; + } + + opcode =be32_to_cpu (ohdr->bth[0 ]) >>24 ; + dev->opstats[opcode].n_bytes += tlen; + dev->opstats[opcode].n_packets++; + +/* Get the destination QP number. */ + qp_num =be32_to_cpu (ohdr->bth[1 ]) &IPS_QPN_MASK ; +if (qp_num ==IPS_MULTICAST_QPN ) { +struct ipath_mcast *mcast; +struct ipath_mcast_qp *p; + + mcast =ipath_mcast_find (&hdr->u.l.grh.dgid); +if (mcast ==NULL ) { + dev->n_pkt_drops++; + goto bail; + } + dev->n_multicast_rcv++; +list_for_each_entry_rcu (p, &mcast->qp_list, list) +ipath_qp_rcv (dev, hdr, lnh ==IPS_LRH_GRH , data, + tlen, p->qp); +/* +* Notify ipath_multicast_detach() if it is waiting for us +* to finish. +*/ +if (atomic_dec_return (&mcast->refcount) <=1 ) +wake_up (&mcast->wait); + }else { + qp =ipath_lookup_qpn (&dev->qp_table, qp_num); +if (qp) { + dev->n_unicast_rcv++; +ipath_qp_rcv (dev, hdr, lnh ==IPS_LRH_GRH , data, + tlen, qp); +/* +* Notify ipath_destroy_qp() if it is waiting +* for us to finish. +*/ +if (atomic_dec_and_test (&qp->refcount)) +wake_up (&qp->wait); + }else + dev->n_pkt_drops++; + } + +bail:; +} + +/** +* ipath_ib_timer - verbs timer +* @arg: the device pointer +* +* This is called from ipath_do_rcv_timer() at interrupt level to check for +* QPs which need retransmits and to collect performance numbers. +*/ +static void ipath_ib_timer (void *arg) +{ +struct ipath_ibdev *dev = (struct ipath_ibdev *) arg; +struct ipath_qp *resend =NULL ; +struct ipath_qp *rnr =NULL ; +struct list_head *last; +struct ipath_qp *qp; +unsigned long flags; + +if (dev ==NULL ) +return ; + +spin_lock_irqsave (&dev->pending_lock, flags); +/* Start filling the next pending queue. */ +if (++dev->pending_index >=ARRAY_SIZE (dev->pending)) + dev->pending_index =0 ; +/* Save any requests still in the new queue, they have timed out. */ + last = &dev->pending[dev->pending_index]; +while (!list_empty (last)) { + qp = list_entry(last->next, struct ipath_qp, timerwait); +if (last->next ==LIST_POISON1 || + last->next != &qp->timerwait || + qp->timerwait.prev != last) { +INIT_LIST_HEAD (last); + }else { +list_del (&qp->timerwait); + qp->timerwait.prev = (struct list_head *) resend; + resend = qp; +atomic_inc (&qp->refcount); + } + } + last = &dev->rnrwait; +if (!list_empty (last)) { + qp = list_entry(last->next, struct ipath_qp, timerwait); +if (--qp->s_rnr_timeout ==0 ) { +do { +if (last->next ==LIST_POISON1 || + last->next != &qp->timerwait || + qp->timerwait.prev != last) { +INIT_LIST_HEAD (last); +break ; + } +list_del (&qp->timerwait); + qp->timerwait.prev = + (struct list_head *) rnr; + rnr = qp; +if (list_empty (last)) +break ; + qp = list_entry(last->next, struct ipath_qp, + timerwait); + }while (qp->s_rnr_timeout ==0 ); + } + } +/* +* We should only be in the started state if pma_sample_start != 0 +*/ +if (dev->pma_sample_status ==IB_PMA_SAMPLE_STATUS_STARTED && + --dev->pma_sample_start ==0 ) { + dev->pma_sample_status =IB_PMA_SAMPLE_STATUS_RUNNING ; +ipath_layer_snapshot_counters (dev->dd, &dev->ipath_sword, + &dev->ipath_rword, + &dev->ipath_spkts, + &dev->ipath_rpkts, + &dev->ipath_xmit_wait); + } +if (dev->pma_sample_status ==IB_PMA_SAMPLE_STATUS_RUNNING ) { +if (dev->pma_sample_interval ==0 ) { +u64 ta, tb, tc, td, te; + + dev->pma_sample_status =IB_PMA_SAMPLE_STATUS_DONE ; +ipath_layer_snapshot_counters (dev->dd, &ta, &tb, + &tc, &td, &te); + + dev->ipath_sword = ta - dev->ipath_sword; + dev->ipath_rword = tb - dev->ipath_rword; + dev->ipath_spkts = tc - dev->ipath_spkts; + dev->ipath_rpkts = td - dev->ipath_rpkts; + dev->ipath_xmit_wait = te - dev->ipath_xmit_wait; + } +else + dev->pma_sample_interval--; + } +spin_unlock_irqrestore (&dev->pending_lock, flags); + +/* XXX What if timer fires again while this is running? */ +for (qp = resend; qp !=NULL ; + qp = (struct ipath_qp *) qp->timerwait.prev) { +struct ib_wc wc; + +spin_lock_irqsave (&qp->s_lock, flags); +if (qp->s_last != qp->s_tail && qp->state ==IB_QPS_RTS ) { + dev->n_timeouts++; +ipath_restart_rc (qp, qp->s_last_psn +1 , &wc); + } +spin_unlock_irqrestore (&qp->s_lock, flags); + +/* Notify ipath_destroy_qp() if it is waiting. */ +if (atomic_dec_and_test (&qp->refcount)) +wake_up (&qp->wait); + } +for (qp = rnr; qp !=NULL ; + qp = (struct ipath_qp *) qp->timerwait.prev) +tasklet_hi_schedule (&qp->s_task); +} + +/** +* ipath_ib_piobufavail - callback when a PIO buffer is available +* @arg: the device pointer +* +* This is called from ipath_intr() at interrupt level when a PIO buffer is +* available after ipath_verbs_send() returned an error that no buffers were +* available. Return 0 if we consumed all the PIO buffers and we still have +* QPs waiting for buffers (for now, just do a tasklet_hi_schedule and +* return one). +*/ +static int ipath_ib_piobufavail (void *arg) +{ +struct ipath_ibdev *dev = (struct ipath_ibdev *) arg; +struct ipath_qp *qp; +unsigned long flags; + +if (dev ==NULL ) + goto bail; + +spin_lock_irqsave (&dev->pending_lock, flags); +while (!list_empty (&dev->piowait)) { + qp = list_entry(dev->piowait.next, struct ipath_qp, + piowait); +list_del (&qp->piowait); +tasklet_hi_schedule (&qp->s_task); + } +spin_unlock_irqrestore (&dev->pending_lock, flags); + +bail: +return 1 ; +} + +static int ipath_query_device (struct ib_device *ibdev, +struct ib_device_attr *props) +{ +struct ipath_ibdev *dev =to_idev (ibdev); +u32 vendor, boardrev, majrev, minrev; + +memset (props,0 ,sizeof (*props)); + + props->device_cap_flags =IB_DEVICE_BAD_PKEY_CNTR | +IB_DEVICE_BAD_QKEY_CNTR |IB_DEVICE_SHUTDOWN_PORT | +IB_DEVICE_SYS_IMAGE_GUID ; +ipath_layer_query_device (dev->dd, &vendor, &boardrev, + &majrev, &minrev); + props->vendor_id = vendor; + props->vendor_part_id = boardrev; + props->hw_ver = boardrev <<16 | majrev <<8 | minrev; + + props->sys_image_guid = dev->sys_image_guid; + + props->max_mr_size = ~0ull ; + props->max_qp =0xffff ; + props->max_qp_wr =0xffff ; + props->max_sge =255 ; + props->max_cq =0xffff ; + props->max_cqe =0xffff ; + props->max_mr =0xffff ; + props->max_pd =0xffff ; + props->max_qp_rd_atom =1 ; + props->max_qp_init_rd_atom =1 ; +/* props->max_res_rd_atom */ + props->max_srq =0xffff ; + props->max_srq_wr =0xffff ; + props->max_srq_sge =255 ; +/* props->local_ca_ack_delay */ + props->atomic_cap =IB_ATOMIC_HCA ; + props->max_pkeys =ipath_layer_get_npkeys (dev->dd); + props->max_mcast_grp =0xffff ; + props->max_mcast_qp_attach =0xffff ; + props->max_total_mcast_qp_attach = props->max_mcast_qp_attach * + props->max_mcast_grp; + +return 0 ; +} + +const u8 ipath_cvt_physportstate[16 ] = { + [INFINIPATH_IBCS_LT_STATE_DISABLED ] =3 , + [INFINIPATH_IBCS_LT_STATE_LINKUP ] =5 , + [INFINIPATH_IBCS_LT_STATE_POLLACTIVE ] =2 , + [INFINIPATH_IBCS_LT_STATE_POLLQUIET ] =2 , + [INFINIPATH_IBCS_LT_STATE_SLEEPDELAY ] =1 , + [INFINIPATH_IBCS_LT_STATE_SLEEPQUIET ] =1 , + [INFINIPATH_IBCS_LT_STATE_CFGDEBOUNCE ] =4 , + [INFINIPATH_IBCS_LT_STATE_CFGRCVFCFG ] =4 , + [INFINIPATH_IBCS_LT_STATE_CFGWAITRMT ] =4 , + [INFINIPATH_IBCS_LT_STATE_CFGIDLE ] =4 , + [INFINIPATH_IBCS_LT_STATE_RECOVERRETRAIN ] =6 , + [INFINIPATH_IBCS_LT_STATE_RECOVERWAITRMT ] =6 , + [INFINIPATH_IBCS_LT_STATE_RECOVERIDLE ] =6 , +}; + +static int ipath_query_port (struct ib_device *ibdev, +u8 port,struct ib_port_attr *props) +{ +struct ipath_ibdev *dev =to_idev (ibdev); +enum ib_mtu mtu; +u16 lid =ipath_layer_get_lid (dev->dd); +u64 ibcstat; + +memset (props,0 ,sizeof (*props)); + props->lid = lid ? lid :__constant_be16_to_cpu (IB_LID_PERMISSIVE ); + props->lmc = dev->mkeyprot_resv_lmc &7 ; + props->sm_lid = dev->sm_lid; + props->sm_sl = dev->sm_sl; + ibcstat =ipath_layer_get_lastibcstat (dev->dd); + props->state = ((ibcstat >>4 ) &0x3 ) +1 ; +/* See phys_state_show() */ + props->phys_state = ipath_cvt_physportstate[ +ipath_layer_get_lastibcstat (dev->dd) &0xf ]; + props->port_cap_flags = dev->port_cap_flags; + props->gid_tbl_len =1 ; + props->max_msg_sz =4096 ; + props->pkey_tbl_len =ipath_layer_get_npkeys (dev->dd); + props->bad_pkey_cntr =ipath_layer_get_cr_errpkey (dev->dd) - + dev->n_pkey_violations; + props->qkey_viol_cntr = dev->qkey_violations; + props->active_width =IB_WIDTH_4X ; +/* See rate_show() */ + props->active_speed =1 ;/* Regular 10Mbs speed. */ + props->max_vl_num =1 ;/* VLCap = VL0 */ + props->init_type_reply =0 ; + + props->max_mtu =IB_MTU_4096 ; +switch (ipath_layer_get_ibmtu (dev->dd)) { +case 4096 : + mtu =IB_MTU_4096 ; +break ; +case 2048 : + mtu =IB_MTU_2048 ; +break ; +case 1024 : + mtu =IB_MTU_1024 ; +break ; +case 512 : + mtu =IB_MTU_512 ; +break ; +case 256 : + mtu =IB_MTU_256 ; +break ; +default : + mtu =IB_MTU_2048 ; + } + props->active_mtu = mtu; + props->subnet_timeout = dev->subnet_timeout; + +return 0 ; +} + +static int ipath_modify_device (struct ib_device *device, +int device_modify_mask, +struct ib_device_modify *device_modify) +{ +int ret; + +if (device_modify_mask & ~(IB_DEVICE_MODIFY_SYS_IMAGE_GUID | +IB_DEVICE_MODIFY_NODE_DESC )) { + ret = -EOPNOTSUPP ; + goto bail; + } + +if (device_modify_mask &IB_DEVICE_MODIFY_NODE_DESC ) +memcpy (device->node_desc, device_modify->node_desc,64 ); + +if (device_modify_mask &IB_DEVICE_MODIFY_SYS_IMAGE_GUID ) +to_idev (device)->sys_image_guid = +cpu_to_be64 (device_modify->sys_image_guid); + + ret =0 ; + +bail: +return ret; +} + +static int ipath_modify_port (struct ib_device *ibdev, +u8 port,int port_modify_mask, +struct ib_port_modify *props) +{ +struct ipath_ibdev *dev =to_idev (ibdev); + + dev->port_cap_flags |= props->set_port_cap_mask; + dev->port_cap_flags &= ~props->clr_port_cap_mask; +if (port_modify_mask &IB_PORT_SHUTDOWN ) +ipath_layer_set_linkstate (dev->dd,IPATH_IB_LINKDOWN ); +if (port_modify_mask &IB_PORT_RESET_QKEY_CNTR ) + dev->qkey_violations =0 ; +return 0 ; +} + +static int ipath_query_gid (struct ib_device *ibdev,u8 port, +int index,union ib_gid *gid) +{ +struct ipath_ibdev *dev =to_idev (ibdev); +int ret; + +if (index >=1 ) { + ret = -EINVAL ; + goto bail; + } + gid->global.subnet_prefix = dev->gid_prefix; + gid->global.interface_id =ipath_layer_get_guid (dev->dd); + + ret =0 ; + +bail: +return ret; +} + +static struct ib_pd *ipath_alloc_pd (struct ib_device *ibdev, +struct ib_ucontext *context, +struct ib_udata *udata) +{ +struct ipath_pd *pd; +struct ib_pd *ret; + + pd =kmalloc (sizeof *pd,GFP_KERNEL ); +if (!pd) { + ret =ERR_PTR (-ENOMEM ); + goto bail; + } + +/* ib_alloc_pd() will initialize pd->ibpd. */ + pd->user = udata !=NULL ; + + ret = &pd->ibpd; + +bail: +return ret; +} + +static int ipath_dealloc_pd (struct ib_pd *ibpd) +{ +struct ipath_pd *pd =to_ipd (ibpd); + +kfree (pd); + +return 0 ; +} + +/** +* ipath_create_ah - create an address handle +* @pd: the protection domain +* @ah_attr: the attributes of the AH +* +* This may be called from interrupt context. +*/ +static struct ib_ah *ipath_create_ah (struct ib_pd *pd, +struct ib_ah_attr *ah_attr) +{ +struct ipath_ah *ah; +struct ib_ah *ret; + +/* A multicast address requires a GRH (see ch. 8.4.1). */ +if (ah_attr->dlid >=IPS_MULTICAST_LID_BASE && + ah_attr->dlid !=IPS_PERMISSIVE_LID && + !(ah_attr->ah_flags &IB_AH_GRH )) { + ret =ERR_PTR (-EINVAL ); + goto bail; + } + + ah =kmalloc (sizeof *ah,GFP_ATOMIC ); +if (!ah) { + ret =ERR_PTR (-ENOMEM ); + goto bail; + } + +/* ib_create_ah() will initialize ah->ibah. */ + ah->attr = *ah_attr; + + ret = &ah->ibah; + +bail: +return ret; +} + +/** +* ipath_destroy_ah - destroy an address handle +* @ibah: the AH to destroy +* +* This may be called from interrupt context. +*/ +static int ipath_destroy_ah (struct ib_ah *ibah) +{ +struct ipath_ah *ah =to_iah (ibah); + +kfree (ah); + +return 0 ; +} + +static int ipath_query_ah (struct ib_ah *ibah,struct ib_ah_attr *ah_attr) +{ +struct ipath_ah *ah =to_iah (ibah); + + *ah_attr = ah->attr; + +return 0 ; +} + +static int ipath_query_pkey (struct ib_device *ibdev,u8 port,u16 index, +u16 *pkey) +{ +struct ipath_ibdev *dev =to_idev (ibdev); +int ret; + +if (index >=ipath_layer_get_npkeys (dev->dd)) { + ret = -EINVAL ; + goto bail; + } + + *pkey =ipath_layer_get_pkey (dev->dd, index); + ret =0 ; + +bail: +return ret; +} + + +/** +* ipath_alloc_ucontext - allocate a ucontest +* @ibdev: the infiniband device +* @udata: not used by the InfiniPath driver +*/ + +static struct ib_ucontext *ipath_alloc_ucontext (struct ib_device *ibdev, +struct ib_udata *udata) +{ +struct ipath_ucontext *context; +struct ib_ucontext *ret; + + context =kmalloc (sizeof *context,GFP_KERNEL ); +if (!context) { + ret =ERR_PTR (-ENOMEM ); + goto bail; + } + + ret = &context->ibucontext; + +bail: +return ret; +} + +static int ipath_dealloc_ucontext (struct ib_ucontext *context) +{ +kfree (to_iucontext (context)); +return 0 ; +} + +static int ipath_verbs_register_sysfs (struct ib_device *dev); + +/** +* ipath_register_ib_device - register our device with the infiniband core +* @unit: the device number to register +* @dd: the device data structure +* Return the allocated ipath_ibdev pointer or NULL on error. +*/ +static void *ipath_register_ib_device (int unit,struct ipath_devdata *dd) +{ +struct ipath_ibdev *idev; +struct ib_device *dev; +int ret; + + idev = (struct ipath_ibdev *)ib_alloc_device (sizeof *idev); +if (idev ==NULL ) + goto bail; + + dev = &idev->ibdev; + +/* Only need to initialize non-zero fields. */ +spin_lock_init (&idev->qp_table.lock); +spin_lock_init (&idev->lk_table.lock); + idev->sm_lid =__constant_be16_to_cpu (IB_LID_PERMISSIVE ); +/* Set the prefix to the default value (see ch. 4.1.1) */ + idev->gid_prefix =__constant_cpu_to_be64 (0xfe80000000000000ULL ); + + ret =ipath_init_qp_table (idev, ib_ipath_qp_table_size); +if (ret) + goto err_qp; + +/* +* The top ib_ipath_lkey_table_size bits are used to index the +* table. The lower 8 bits can be owned by the user (copied from +* the LKEY). The remaining bits act as a generation number or tag. +*/ + idev->lk_table.max =1 << ib_ipath_lkey_table_size; + idev->lk_table.table =kzalloc (idev->lk_table.max * +sizeof (*idev->lk_table.table), +GFP_KERNEL ); +if (idev->lk_table.table ==NULL ) { + ret = -ENOMEM ; + goto err_lk; + } +spin_lock_init (&idev->pending_lock); +INIT_LIST_HEAD (&idev->pending[0 ]); +INIT_LIST_HEAD (&idev->pending[1 ]); +INIT_LIST_HEAD (&idev->pending[2 ]); +INIT_LIST_HEAD (&idev->piowait); +INIT_LIST_HEAD (&idev->rnrwait); + idev->pending_index =0 ; + idev->port_cap_flags = +IB_PORT_SYS_IMAGE_GUID_SUP |IB_PORT_CLIENT_REG_SUP ; + idev->pma_counter_select[0 ] =IB_PMA_PORT_XMIT_DATA ; + idev->pma_counter_select[1 ] =IB_PMA_PORT_RCV_DATA ; + idev->pma_counter_select[2 ] =IB_PMA_PORT_XMIT_PKTS ; + idev->pma_counter_select[3 ] =IB_PMA_PORT_RCV_PKTS ; + idev->pma_counter_select[5 ] =IB_PMA_PORT_XMIT_WAIT ; + idev->link_width_enabled =3 ;/* 1x or 4x */ + +/* +* The system image GUID is supposed to be the same for all +* IB HCAs in a single system but since there can be other +* device types in the system, we can't be sure this is unique. +*/ +if (!sys_image_guid) + sys_image_guid =ipath_layer_get_guid (dd); + idev->sys_image_guid = sys_image_guid; + idev->ib_unit = unit; + idev->dd = dd; + +strlcpy (dev->name,"ipath%d" ,IB_DEVICE_NAME_MAX ); + dev->node_guid =ipath_layer_get_guid (dd); + dev->uverbs_abi_ver =IPATH_UVERBS_ABI_VERSION ; + dev->uverbs_cmd_mask = + (1ull <<IB_USER_VERBS_CMD_GET_CONTEXT ) | + (1ull <<IB_USER_VERBS_CMD_QUERY_DEVICE ) | + (1ull <<IB_USER_VERBS_CMD_QUERY_PORT ) | + (1ull <<IB_USER_VERBS_CMD_ALLOC_PD ) | + (1ull <<IB_USER_VERBS_CMD_DEALLOC_PD ) | + (1ull <<IB_USER_VERBS_CMD_CREATE_AH ) | + (1ull <<IB_USER_VERBS_CMD_DESTROY_AH ) | + (1ull <<IB_USER_VERBS_CMD_QUERY_AH ) | + (1ull <<IB_USER_VERBS_CMD_REG_MR ) | + (1ull <<IB_USER_VERBS_CMD_DEREG_MR ) | + (1ull <<IB_USER_VERBS_CMD_CREATE_COMP_CHANNEL ) | + (1ull <<IB_USER_VERBS_CMD_CREATE_CQ ) | + (1ull <<IB_USER_VERBS_CMD_RESIZE_CQ ) | + (1ull <<IB_USER_VERBS_CMD_DESTROY_CQ ) | + (1ull <<IB_USER_VERBS_CMD_POLL_CQ ) | + (1ull <<IB_USER_VERBS_CMD_REQ_NOTIFY_CQ ) | + (1ull <<IB_USER_VERBS_CMD_CREATE_QP ) | + (1ull <<IB_USER_VERBS_CMD_QUERY_QP ) | + (1ull <<IB_USER_VERBS_CMD_MODIFY_QP ) | + (1ull <<IB_USER_VERBS_CMD_DESTROY_QP ) | + (1ull <<IB_USER_VERBS_CMD_POST_SEND ) | + (1ull <<IB_USER_VERBS_CMD_POST_RECV ) | + (1ull <<IB_USER_VERBS_CMD_ATTACH_MCAST ) | + (1ull <<IB_USER_VERBS_CMD_DETACH_MCAST ) | + (1ull <<IB_USER_VERBS_CMD_CREATE_SRQ ) | + (1ull <<IB_USER_VERBS_CMD_MODIFY_SRQ ) | + (1ull <<IB_USER_VERBS_CMD_QUERY_SRQ ) | + (1ull <<IB_USER_VERBS_CMD_DESTROY_SRQ ) | + (1ull <<IB_USER_VERBS_CMD_POST_SRQ_RECV ); + dev->node_type =IB_NODE_CA ; + dev->phys_port_cnt =1 ; + dev->dma_device =ipath_layer_get_device (dd); + dev->class_dev.dev = dev->dma_device; + dev->query_device = ipath_query_device; + dev->modify_device = ipath_modify_device; + dev->query_port = ipath_query_port; + dev->modify_port = ipath_modify_port; + dev->query_pkey = ipath_query_pkey; + dev->query_gid = ipath_query_gid; + dev->alloc_ucontext = ipath_alloc_ucontext; + dev->dealloc_ucontext = ipath_dealloc_ucontext; + dev->alloc_pd = ipath_alloc_pd; + dev->dealloc_pd = ipath_dealloc_pd; + dev->create_ah = ipath_create_ah; + dev->destroy_ah = ipath_destroy_ah; + dev->query_ah = ipath_query_ah; + dev->create_srq = ipath_create_srq; + dev->modify_srq = ipath_modify_srq; + dev->query_srq = ipath_query_srq; + dev->destroy_srq = ipath_destroy_srq; + dev->create_qp = ipath_create_qp; + dev->modify_qp = ipath_modify_qp; + dev->query_qp = ipath_query_qp; + dev->destroy_qp = ipath_destroy_qp; + dev->post_send = ipath_post_send; + dev->post_recv = ipath_post_receive; + dev->post_srq_recv = ipath_post_srq_receive; + dev->create_cq = ipath_create_cq; + dev->destroy_cq = ipath_destroy_cq; + dev->resize_cq = ipath_resize_cq; + dev->poll_cq = ipath_poll_cq; + dev->req_notify_cq = ipath_req_notify_cq; + dev->get_dma_mr = ipath_get_dma_mr; + dev->reg_phys_mr = ipath_reg_phys_mr; + dev->reg_user_mr = ipath_reg_user_mr; + dev->dereg_mr = ipath_dereg_mr; + dev->alloc_fmr = ipath_alloc_fmr; + dev->map_phys_fmr = ipath_map_phys_fmr; + dev->unmap_fmr = ipath_unmap_fmr; + dev->dealloc_fmr = ipath_dealloc_fmr; + dev->attach_mcast = ipath_multicast_attach; + dev->detach_mcast = ipath_multicast_detach; + dev->process_mad = ipath_process_mad; + +snprintf (dev->node_desc,sizeof (dev->node_desc), +IPATH_IDSTR " %s kernel_SMA" , system_utsname.nodename); + + ret =ib_register_device (dev); +if (ret) + goto err_reg; + +if (ipath_verbs_register_sysfs (dev)) + goto err_class; + +ipath_layer_enable_timer (dd); + + goto bail; + +err_class: +ib_unregister_device (dev); +err_reg: +kfree (idev->lk_table.table); +err_lk: +kfree (idev->qp_table.table); +err_qp: +ib_dealloc_device (dev); +_VERBS_ERROR ("ib_ipath%d cannot register verbs (%d)!\n" , + unit, -ret); + idev =NULL ; + +bail: +return idev; +} + +static void ipath_unregister_ib_device (void *arg) +{ +struct ipath_ibdev *dev = (struct ipath_ibdev *) arg; +struct ib_device *ibdev = &dev->ibdev; + +ipath_layer_disable_timer (dev->dd); + +ib_unregister_device (ibdev); + +if (!list_empty (&dev->pending[0 ]) || + !list_empty (&dev->pending[1 ]) || + !list_empty (&dev->pending[2 ])) +_VERBS_ERROR ("ipath%d pending list not empty!\n" , + dev->ib_unit); +if (!list_empty (&dev->piowait)) +_VERBS_ERROR ("ipath%d piowait list not empty!\n" , + dev->ib_unit); +if (!list_empty (&dev->rnrwait)) +_VERBS_ERROR ("ipath%d rnrwait list not empty!\n" , + dev->ib_unit); +if (!ipath_mcast_tree_empty ()) +_VERBS_ERROR ("ipath%d multicast table memory leak!\n" , + dev->ib_unit); +/* +* Note that ipath_unregister_ib_device() can be called before all +* the QPs are destroyed! +*/ +ipath_free_all_qps (&dev->qp_table); +kfree (dev->qp_table.table); +kfree (dev->lk_table.table); +ib_dealloc_device (ibdev); +} + +int __init ipath_verbs_init (void ) +{ +return ipath_verbs_register (ipath_register_ib_device, + ipath_unregister_ib_device, + ipath_ib_piobufavail, ipath_ib_rcv, + ipath_ib_timer); +} + +void __exit ipath_verbs_cleanup(void) +{ +ipath_verbs_unregister (); +} + +static ssize_t show_rev (struct class_device *cdev,char *buf) +{ +struct ipath_ibdev *dev = + container_of(cdev, struct ipath_ibdev, ibdev.class_dev); +int vendor, boardrev, majrev, minrev; + +ipath_layer_query_device (dev->dd, &vendor, &boardrev, + &majrev, &minrev); +return sprintf (buf,"%d.%d\n" , majrev, minrev); +} + +static ssize_t show_hca (struct class_device *cdev,char *buf) +{ +struct ipath_ibdev *dev = + container_of(cdev, struct ipath_ibdev, ibdev.class_dev); +int ret; + + ret =ipath_layer_get_boardname (dev->dd, buf,128 ); +if (ret <0 ) + goto bail; +strcat (buf,"\n" ); + ret =strlen (buf); + +bail: +return ret; +} + +static ssize_t show_stats (struct class_device *cdev,char *buf) +{ +struct ipath_ibdev *dev = + container_of(cdev, struct ipath_ibdev, ibdev.class_dev); +int i; +int len; + + len =sprintf (buf, +"RC resends %d\n" +"RC QACKs %d\n" +"RC ACKs %d\n" +"RC SEQ NAKs %d\n" +"RC RDMA seq %d\n" +"RC RNR NAKs %d\n" +"RC OTH NAKs %d\n" +"RC timeouts %d\n" +"RC RDMA dup %d\n" +"piobuf wait %d\n" +"no piobuf %d\n" +"PKT drops %d\n" +"WQE errs %d\n" , + dev->n_rc_resends, dev->n_rc_qacks, dev->n_rc_acks, + dev->n_seq_naks, dev->n_rdma_seq, dev->n_rnr_naks, + dev->n_other_naks, dev->n_timeouts, + dev->n_rdma_dup_busy, dev->n_piowait, + dev->n_no_piobuf, dev->n_pkt_drops, dev->n_wqe_errs); +for (i =0 ; i <ARRAY_SIZE (dev->opstats); i++) { +const struct ipath_opcode_stats *si = &dev->opstats[i]; + +if (!si->n_packets && !si->n_bytes) +continue ; + len +=sprintf (buf + len,"%02x %llu/%llu\n" , i, + (unsigned long long ) si->n_packets, + (unsigned long long ) si->n_bytes); + } +return len; +} + +static CLASS_DEVICE_ATTR(hw_rev, S_IRUGO, show_rev, NULL); +static CLASS_DEVICE_ATTR(hca_type, S_IRUGO, show_hca, NULL); +static CLASS_DEVICE_ATTR(board_id, S_IRUGO, show_hca, NULL); +static CLASS_DEVICE_ATTR(stats, S_IRUGO, show_stats, NULL); + +static struct class_device_attribute *ipath_class_attributes[] = { + &class_device_attr_hw_rev, + &class_device_attr_hca_type, + &class_device_attr_board_id, + &class_device_attr_stats +}; + +static int ipath_verbs_register_sysfs (struct ib_device *dev) +{ +int i; +int ret; + +for (i =0 ; i <ARRAY_SIZE (ipath_class_attributes); ++i) +if (class_device_create_file (&dev->class_dev, + ipath_class_attributes[i])) { + ret =1 ; + goto bail; + } + + ret =0 ; + +bail: +return ret; +} + +module_init (ipath_verbs_init); +module_exit (ipath_verbs_cleanup);
drivers/infiniband/hw/ipath/ipath_verbs_mcast.c new file +333 -0
333 lines not on this page · raw message
PATCH 1/1 ipath - kbuild infrastructure
In reply to Bryan O'SullivanIntegrate the ipath core and OpenIB drivers into the kernel build infrastructure. Add entry to MAINTAINERS.
MAINTAINERS +6 -0
@@ -1450,6 +1450,12 @@ P: Juanjo Ciarlante P: Juanjo Ciarlante M: [email protected] S: Maintained + +IPATH DRIVER: +P: Bryan O'Sullivan +M: [email protected] +L: [email protected] +S: Supported IPX NETWORK LAYER P: Arnaldo Carvalho de Melo
drivers/infiniband/Kconfig +1 -0
@@ -30,6 +30,7 @@ config INFINIBAND_USER_ACCESS <http://www.openib.org>. source "drivers/infiniband/hw/mthca/Kconfig" +source "drivers/infiniband/hw/ipath/Kconfig" source "drivers/infiniband/ulp/ipoib/Kconfig"
drivers/infiniband/Makefile +1 -0
@@ -1,4 +1,5 @@ obj-$(CONFIG_INFINIBAND) += core/ obj-$(CONFIG_INFINIBAND) += core/ obj-$(CONFIG_INFINIBAND_MTHCA) += hw/mthca/ +obj-$(CONFIG_IPATH_CORE) += hw/ipath/ obj-$(CONFIG_INFINIBAND_IPOIB) += ulp/ipoib/ obj-$(CONFIG_INFINIBAND_SRP) += ulp/srp/
drivers/infiniband/hw/ipath/Kconfig new file +16 -0
@@ -0,0 +1,16 @@ +config IPATH_CORE + tristate "PathScale InfiniPath Driver" + depends on 64BIT && PCI_MSI + ---help--- + This is a low-level driver for PathScale InfiniPath host channel + adapters (HCAs) based on the HT-400 and PE-800 chips. + +config INFINIBAND_IPATH + tristate "PathScale InfiniPath Verbs Driver" + depends on IPATH_CORE && INFINIBAND + ---help--- + This is a driver that provides InfiniBand verbs support for + PathScale InfiniPath host channel adapters (HCAs). This + allows these devices to be used with both kernel upper level + protocols such as IP-over-InfiniBand as well as with userspace + applications (in conjunction with InfiniBand userspace access).
drivers/infiniband/hw/ipath/Makefile new file +36 -0
@@ -0,0 +1,36 @@ +EXTRA_CFLAGS += -DIPATH_IDSTR='"PathScale kernel.org driver"' \ + -DIPATH_KERN_TYPE=0 + +obj-$(CONFIG_IPATH_CORE) += ipath_core.o +obj-$(CONFIG_INFINIBAND_IPATH) += ib_ipath.o + +ipath_core-y := \ + ipath_diag.o \ + ipath_driver.o \ + ipath_eeprom.o \ + ipath_file_ops.o \ + ipath_fs.o \ + ipath_ht400.o \ + ipath_init_chip.o \ + ipath_intr.o \ + ipath_layer.o \ + ipath_pe800.o \ + ipath_stats.o \ + ipath_sysfs.o \ + ipath_user_pages.o + +ipath_core-$(CONFIG_X86_64) += ipath_wc_x86_64.o + +ib_ipath-y := \ + ipath_cq.o \ + ipath_keys.o \ + ipath_mad.o \ + ipath_mr.o \ + ipath_qp.o \ + ipath_rc.o \ + ipath_ruc.o \ + ipath_srq.o \ + ipath_uc.o \ + ipath_ud.o \ + ipath_verbs.o \ + ipath_verbs_mcast.o
Re: [PATCH 16 of 16] ipath - kbuild infrastructure
Also, have you tried building with CONFIG_IPATH_CORE=y but CONFIG_INFINIBAND=n? It looks like it won't work, because the only way for the build system to reach the driver source is via
obj-$(CONFIG_INFINIBAND) += infiniband/
in drivers/Makefile.
I'm not sure what the cleanest way to fix this.
Sorry for not noticing this sooner...
- R.
Re: [PATCH 16 of 16] ipath - kbuild infrastructure
Quoted 1 line · Roland Dreier
I'm not sure what the cleanest way to fix this.
I did ask at one point whether the core driver should live in a directory in drivers/char/, since it's not really an IB driver at all, and just have the IB-specific stuff live in drivers/infiniband/hw/.
I'm still amenable to doing that.
Quoted 1 line
Sorry for not noticing this sooner...
No worries.
<b
Re: [PATCH 16 of 16] ipath - kbuild infrastructure
Bryan> I did ask at one point whether the core driver should live Bryan> in a directory in drivers/char/, since it's not really an Bryan> IB driver at all, and just have the IB-specific stuff live Bryan> in drivers/infiniband/hw/.
I guess we could do that (now or later).
For now how about something minimal like the change below?
Sam, does this seem OK to you? (The situation is that the IPATH_CORE source physically sits in drivers/infiniband/hw/ipath, but it is possible to enable IPATH_CORE without enabling INFINIBAND. So we need to tell the build system to descend into drivers/infiniband if IPATH_CORE is enabled, even if INFINIBAND isn't enabled)
Thanks,
Roland
drivers/Makefile +1 -0
@@ -70,6 +70,7 @@ obj-$(CONFIG_EISA) += eisa/ obj-$(CONFIG_CPU_FREQ) += cpufreq/ obj-$(CONFIG_MMC) += mmc/ obj-$(CONFIG_INFINIBAND) += infiniband/ +obj-$(CONFIG_IPATH_CORE) += infiniband/ obj-$(CONFIG_SGI_SN) += sn/ obj-y += firmware/ obj-$(CONFIG_CRYPTO) += crypto/
Re: [PATCH 16 of 16] ipath - kbuild infrastructure
Quoted 7 lines · Roland Dreier
Bryan> I did ask at one point whether the core driver should live Bryan> in a directory in
drivers/char/, since it's not really an Bryan> IB driver at all, and just have the IB-specific stuff live Bryan> indrivers/infiniband/hw/.I guess we could do that (now or later).
Quoted 7 lines
For now how about something minimal like the change below?
Sam, does this seem OK to you? (The situation is that the
IPATH_COREsource physically sits indrivers/infiniband/hw/ipath, but it is possible to enableIPATH_COREwithout enabling INFINIBAND. So we need to tell the build system to descend intodrivers/infinibandifIPATH_COREis enabled, even if INFINIBAND isn't enabled)
Hi Roland.
This looks OK. Specifying the same subdirectory twice is no problem.
Sam
PATCH 1/1 ipath - infiniband header files
In reply to Bryan O'SullivanThese header files are used by the layered Infiniband driver.
drivers/infiniband/hw/ipath/ipath_verbs.h new file +697 -0
@@ -0,0 +1,697 @@ +/* +* Copyright (c) 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#ifndef IPATH_VERBS_H +#define IPATH_VERBS_H + +#include <linux/types.h> +#include <linux/spinlock.h> +#include <linux/kernel.h> +#include <linux/interrupt.h> +#include <rdma/ib_pack.h> + +#include "ipath_layer.h" +#include "verbs_debug.h" + +#define QPN_MAX (1 << 24) +#define QPNMAP_ENTRIES (QPN_MAX / PAGE_SIZE / BITS_PER_BYTE) + +/* +* Increment this value if any changes that break userspace ABI +* compatibility are made. +*/ +#define IPATH_UVERBS_ABI_VERSION 1 + +/* +* Define an ib_cq_notify value that is not valid so we know when CQ +* notifications are armed. +*/ +#define IB_CQ_NONE (IB_CQ_NEXT_COMP + 1) + +#define IB_RNR_NAK 0x20 +#define IB_NAK_PSN_ERROR 0x60 +#define IB_NAK_INVALID_REQUEST 0x61 +#define IB_NAK_REMOTE_ACCESS_ERROR 0x62 +#define IB_NAK_REMOTE_OPERATIONAL_ERROR 0x63 +#define IB_NAK_INVALID_RD_REQUEST 0x64 + +#define IPATH_POST_SEND_OK 0x01 +#define IPATH_POST_RECV_OK 0x02 +#define IPATH_PROCESS_RECV_OK 0x04 +#define IPATH_PROCESS_SEND_OK 0x08 + +/* IB Performance Manager status values */ +#define IB_PMA_SAMPLE_STATUS_DONE 0x00 +#define IB_PMA_SAMPLE_STATUS_STARTED 0x01 +#define IB_PMA_SAMPLE_STATUS_RUNNING 0x02 + +/* Mandatory IB performance counter select values. */ +#define IB_PMA_PORT_XMIT_DATA __constant_htons(0x0001) +#define IB_PMA_PORT_RCV_DATA __constant_htons(0x0002) +#define IB_PMA_PORT_XMIT_PKTS __constant_htons(0x0003) +#define IB_PMA_PORT_RCV_PKTS __constant_htons(0x0004) +#define IB_PMA_PORT_XMIT_WAIT __constant_htons(0x0005) + +struct ib_reth { +__be64 vaddr; +__be32 rkey; +__be32 length; +} __attribute__ ((packed)); + +struct ib_atomic_eth { +__be64 vaddr; +__be32 rkey; +__be64 swap_data; +__be64 compare_data; +} __attribute__ ((packed)); + +struct ipath_other_headers { +__be32 bth[3 ]; +union { +struct { +__be32 deth[2 ]; +__be32 imm_data; + } ud; +struct { +struct ib_reth reth; +__be32 imm_data; + } rc; +struct { +__be32 aeth; +__be64 atomic_ack_eth; + } at; +__be32 imm_data; +__be32 aeth; +struct ib_atomic_eth atomic_eth; + } u; +} __attribute__ ((packed)); + +/* +* Note that UD packets with a GRH header are 8+40+12+8 = 68 bytes +* long (72 w/ imm_data). Only the first 56 bytes of the IB header +* will be in the eager header buffer. The remaining 12 or 16 bytes +* are in the data buffer. +*/ +struct ipath_ib_header { +__be16 lrh[4 ]; +union { +struct { +struct ib_grh grh; +struct ipath_other_headers oth; + } l; +struct ipath_other_headers oth; + } u; +} __attribute__ ((packed)); + +/* +* There is one struct ipath_mcast for each multicast GID. +* All attached QPs are then stored as a list of +* struct ipath_mcast_qp. +*/ +struct ipath_mcast_qp { +struct list_head list; +struct ipath_qp *qp; +}; + +struct ipath_mcast { +struct rb_node rb_node; +union ib_gid mgid; +struct list_head qp_list; +wait_queue_head_t wait; +atomic_t refcount; +}; + +/* Memory region */ +struct ipath_mr { +struct ib_mr ibmr; +struct ipath_mregion mr;/* must be last */ +}; + +/* Fast memory region */ +struct ipath_fmr { +struct ib_fmr ibfmr; +u8 page_shift; +struct ipath_mregion mr;/* must be last */ +}; + +/* Protection domain */ +struct ipath_pd { +struct ib_pd ibpd; +int user;/* non-zero if created from user space */ +}; + +/* Address Handle */ +struct ipath_ah { +struct ib_ah ibah; +struct ib_ah_attr attr; +}; + +/* +* Quick description of our CQ/QP locking scheme: +* +* We have one global lock that protects dev->cq/qp_table. Each +* struct ipath_cq/qp also has its own lock. An individual qp lock +* may be taken inside of an individual cq lock. Both cqs attached to +* a qp may be locked, with the send cq locked first. No other +* nesting should be done. +* +* Each struct ipath_cq/qp also has an atomic_t ref count. The +* pointer from the cq/qp_table to the struct counts as one reference. +* This reference also is good for access through the consumer API, so +* modifying the CQ/QP etc doesn't need to take another reference. +* Access because of a completion being polled does need a reference. +* +* Finally, each struct ipath_cq/qp has a wait_queue_head_t for the +* destroy function to sleep on. +* +* This means that access from the consumer API requires nothing but +* taking the struct's lock. +* +* Access because of a completion event should go as follows: +* - lock cq/qp_table and look up struct +* - increment ref count in struct +* - drop cq/qp_table lock +* - lock struct, do your thing, and unlock struct +* - decrement ref count; if zero, wake up waiters +* +* To destroy a CQ/QP, we can do the following: +* - lock cq/qp_table, remove pointer, unlock cq/qp_table lock +* - decrement ref count +* - wait_event until ref count is zero +* +* It is the consumer's responsibilty to make sure that no QP +* operations (WQE posting or state modification) are pending when the +* QP is destroyed. Also, the consumer must make sure that calls to +* qp_modify are serialized. +* +* Possible optimizations (wait for profile data to see if/where we +* have locks bouncing between CPUs): +* - split cq/qp table lock into n separate (cache-aligned) locks, +* indexed (say) by the page in the table +*/ + +struct ipath_cq { +struct ib_cq ibcq; +struct tasklet_struct comptask; +spinlock_t lock; +u8 notify; +u8 triggered; +u32 head;/* new records added to the head */ +u32 tail;/* poll_cq() reads from here. */ +struct ib_wc *queue;/* this is actually ibcq.cqe + 1 */ +}; + +/* +* Send work request queue entry. +* The size of the sg_list is determined when the QP is created and stored +* in qp->s_max_sge. +*/ +struct ipath_swqe { +struct ib_send_wr wr;/* don't use wr.sg_list */ +u32 psn;/* first packet sequence number */ +u32 lpsn;/* last packet sequence number */ +u32 ssn;/* send sequence number */ +u32 length;/* total length of data in sg_list */ +struct ipath_sge sg_list[0 ]; +}; + +/* +* Receive work request queue entry. +* The size of the sg_list is determined when the QP is created and stored +* in qp->r_max_sge. +*/ +struct ipath_rwqe { +u64 wr_id; +u32 length;/* total length of data in sg_list */ +u8 num_sge; +struct ipath_sge sg_list[0 ]; +}; + +struct ipath_rq { +spinlock_t lock; +u32 head;/* new work requests posted to the head */ +u32 tail;/* receives pull requests from here. */ +u32 size;/* size of RWQE array */ +u8 max_sge; +struct ipath_rwqe *wq;/* RWQE array */ +}; + +struct ipath_srq { +struct ib_srq ibsrq; +struct ipath_rq rq; +/* send signal when number of RWQEs < limit */ +u32 limit; +}; + +/* +* Variables prefixed with s_ are for the requester (sender). +* Variables prefixed with r_ are for the responder (receiver). +* Variables prefixed with ack_ are for responder replies. +* +* Common variables are protected by both r_rq.lock and s_lock in that order +* which only happens in modify_qp() or changing the QP 'state'. +*/ +struct ipath_qp { +struct ib_qp ibqp; +struct ipath_qp *next;/* link list for QPN hash table */ +struct list_head piowait;/* link for wait PIO buf */ +struct list_head timerwait;/* link for waiting for timeouts */ +struct ib_ah_attr remote_ah_attr; +struct ipath_ib_header s_hdr;/* next packet header to send */ +atomic_t refcount; +wait_queue_head_t wait; +struct tasklet_struct s_task; +struct ipath_sge_state *s_cur_sge; +struct ipath_sge_state s_sge;/* current send request data */ +/* current RDMA read send data */ +struct ipath_sge_state s_rdma_sge; +struct ipath_sge_state r_sge;/* current receive data */ +spinlock_t s_lock; +unsigned long s_flags; +u32 s_hdrwords;/* size of s_hdr in 32 bit words */ +u32 s_cur_size;/* size of send packet in bytes */ +u32 s_len;/* total length of s_sge */ +u32 s_rdma_len;/* total length of s_rdma_sge */ +u32 s_next_psn;/* PSN for next request */ +u32 s_last_psn;/* last response PSN processed */ +u32 s_psn;/* current packet sequence number */ +u32 s_rnr_timeout;/* number of milliseconds for RNR timeout */ +u32 s_ack_psn;/* PSN for next ACK or RDMA_READ */ +u64 s_ack_atomic;/* data for atomic ACK */ +u64 r_wr_id;/* ID for current receive WQE */ +u64 r_atomic_data;/* data for last atomic op */ +u32 r_atomic_psn;/* PSN of last atomic op */ +u32 r_len;/* total length of r_sge */ +u32 r_rcv_len;/* receive data len processed */ +u32 r_psn;/* expected rcv packet sequence number */ +u8 state;/* QP state */ +u8 s_state;/* opcode of last packet sent */ +u8 s_ack_state;/* opcode of packet to ACK */ +u8 s_nak_state;/* non-zero if NAK is pending */ +u8 r_state;/* opcode of last packet received */ +u8 r_reuse_sge;/* for UC receive errors */ +u8 r_sge_inx;/* current index into sg_list */ +u8 s_max_sge;/* size of s_wq->sg_list */ +u8 qp_access_flags; +u8 s_retry_cnt;/* number of times to retry */ +u8 s_rnr_retry_cnt; +u8 s_min_rnr_timer; +u8 s_retry;/* requester retry counter */ +u8 s_rnr_retry;/* requester RNR retry counter */ +u8 s_pkey_index;/* PKEY index to use */ +enum ib_mtu path_mtu; +atomic_t msn;/* message sequence number */ +u32 remote_qpn; +u32 qkey;/* QKEY for this QP (for UD or RD) */ +u32 s_size;/* send work queue size */ +u32 s_head;/* new entries added here */ +u32 s_tail;/* next entry to process */ +u32 s_cur;/* current work queue entry */ +u32 s_last;/* last un-ACK'ed entry */ +u32 s_ssn;/* SSN of tail entry */ +u32 s_lsn;/* limit sequence number (credit) */ +struct ipath_swqe *s_wq;/* send work queue */ +struct ipath_rq r_rq;/* receive work queue */ +}; + +/* +* Bit definitions for s_flags. +*/ +#define IPATH_S_BUSY 0 +#define IPATH_S_SIGNAL_REQ_WR 1 + +/* +* Since struct ipath_swqe is not a fixed size, we can't simply index into +* struct ipath_qp.s_wq. This function does the array index computation. +*/ +static inline struct ipath_swqe *get_swqe_ptr (struct ipath_qp *qp, +unsigned n) +{ +return (struct ipath_swqe *)((char *)qp->s_wq + + (sizeof (struct ipath_swqe ) + + qp->s_max_sge * +sizeof (struct ipath_sge )) * n); +} + +/* +* Since struct ipath_rwqe is not a fixed size, we can't simply index into +* struct ipath_rq.wq. This function does the array index computation. +*/ +static inline struct ipath_rwqe *get_rwqe_ptr (struct ipath_rq *rq, +unsigned n) +{ +return (struct ipath_rwqe *) + ((char *) rq->wq + + (sizeof (struct ipath_rwqe ) + + rq->max_sge *sizeof (struct ipath_sge )) * n); +} + +/* +* QPN-map pages start out as NULL, they get allocated upon +* first use and are never deallocated. This way, +* large bitmaps are not allocated unless large numbers of QPs are used. +*/ +struct qpn_map { +atomic_t n_free; +void *page; +}; + +struct ipath_qp_table { +spinlock_t lock; +u32 last;/* last QP number allocated */ +u32 max;/* size of the hash table */ +u32 nmaps;/* size of the map table */ +struct ipath_qp **table; +/* bit map of free numbers */ +struct qpn_map map[QPNMAP_ENTRIES ]; +}; + +struct ipath_lkey_table { +spinlock_t lock; +u32 next;/* next unused index (speeds search) */ +u32 gen;/* generation count */ +u32 max;/* size of the table */ +struct ipath_mregion **table; +}; + +struct ipath_opcode_stats { +u64 n_packets;/* number of packets */ +u64 n_bytes;/* total number of bytes */ +}; + +struct ipath_ibdev { +struct ib_device ibdev; +struct list_head dev_list; +struct ipath_devdata *dd; +int ib_unit;/* This is the device number */ +u16 sm_lid;/* in host order */ +u8 sm_sl; +u8 mkeyprot_resv_lmc; +/* non-zero when timer is set */ +unsigned long mkey_lease_timeout; + +/* The following fields are really per port. */ +struct ipath_qp_table qp_table; +struct ipath_lkey_table lk_table; +struct list_head pending[3 ];/* FIFO of QPs waiting for ACKs */ +struct list_head piowait;/* list for wait PIO buf */ +/* list of QPs waiting for RNR timer */ +struct list_head rnrwait; +spinlock_t pending_lock; +__be64 sys_image_guid;/* in network order */ +__be64 gid_prefix;/* in network order */ +__be64 mkey; +u64 ipath_sword;/* total dwords sent (sample result) */ +u64 ipath_rword;/* total dwords received (sample result) */ +u64 ipath_spkts;/* total packets sent (sample result) */ +u64 ipath_rpkts;/* total packets received (sample result) */ +/* # of ticks no data sent (sample result) */ +u64 ipath_xmit_wait; +u64 rcv_errors;/* # of packets with SW detected rcv errs */ +u64 n_unicast_xmit;/* total unicast packets sent */ +u64 n_unicast_rcv;/* total unicast packets received */ +u64 n_multicast_xmit;/* total multicast packets sent */ +u64 n_multicast_rcv;/* total multicast packets received */ +u64 n_symbol_error_counter;/* starting count for PMA */ +u64 n_link_error_recovery_counter;/* starting count for PMA */ +u64 n_link_downed_counter;/* starting count for PMA */ +u64 n_port_rcv_errors;/* starting count for PMA */ +u64 n_port_rcv_remphys_errors;/* starting count for PMA */ +u64 n_port_xmit_discards;/* starting count for PMA */ +u64 n_port_xmit_data;/* starting count for PMA */ +u64 n_port_rcv_data;/* starting count for PMA */ +u64 n_port_xmit_packets;/* starting count for PMA */ +u64 n_port_rcv_packets;/* starting count for PMA */ +u32 n_pkey_violations;/* starting count for PMA */ +u32 n_rc_resends; +u32 n_rc_acks; +u32 n_rc_qacks; +u32 n_seq_naks; +u32 n_rdma_seq; +u32 n_rnr_naks; +u32 n_other_naks; +u32 n_timeouts; +u32 n_pkt_drops; +u32 n_wqe_errs; +u32 n_rdma_dup_busy; +u32 n_piowait; +u32 n_no_piobuf; +u32 port_cap_flags; +u32 pma_sample_start; +u32 pma_sample_interval; +__be16 pma_counter_select[5 ]; +u16 pma_tag; +u16 qkey_violations; +u16 mkey_violations; +u16 mkey_lease_period; +u16 pending_index;/* which pending queue is active */ +u8 pma_sample_status; +u8 subnet_timeout; +u8 link_width_enabled; +u8 vl_high_limit; +struct ipath_opcode_stats opstats[128 ]; +}; + +struct ipath_ucontext { +struct ib_ucontext ibucontext; +}; + +static inline struct ipath_mr *to_imr (struct ib_mr *ibmr) +{ + return container_of(ibmr, struct ipath_mr, ibmr); +} + +static inline struct ipath_fmr *to_ifmr (struct ib_fmr *ibfmr) +{ + return container_of(ibfmr, struct ipath_fmr, ibfmr); +} + +static inline struct ipath_pd *to_ipd (struct ib_pd *ibpd) +{ + return container_of(ibpd, struct ipath_pd, ibpd); +} + +static inline struct ipath_ah *to_iah (struct ib_ah *ibah) +{ + return container_of(ibah, struct ipath_ah, ibah); +} + +static inline struct ipath_cq *to_icq (struct ib_cq *ibcq) +{ + return container_of(ibcq, struct ipath_cq, ibcq); +} + +static inline struct ipath_srq *to_isrq (struct ib_srq *ibsrq) +{ + return container_of(ibsrq, struct ipath_srq, ibsrq); +} + +static inline struct ipath_qp *to_iqp (struct ib_qp *ibqp) +{ + return container_of(ibqp, struct ipath_qp, ibqp); +} + +static inline struct ipath_ibdev *to_idev (struct ib_device *ibdev) +{ + return container_of(ibdev, struct ipath_ibdev, ibdev); +} + +int ipath_process_mad (struct ib_device *ibdev, +int mad_flags, +u8 port_num, +struct ib_wc *in_wc, +struct ib_grh *in_grh, +struct ib_mad *in_mad,struct ib_mad *out_mad); + +static inline struct ipath_ucontext *to_iucontext (struct ib_ucontext + *ibucontext) +{ + return container_of(ibucontext, struct ipath_ucontext, ibucontext); +} + +/* +* Compare the lower 24 bits of the two values. +* Returns an integer <, ==, or > than zero. +*/ +static inline int ipath_cmp24 (u32 a,u32 b) +{ +return (((int ) a) - ((int ) b)) <<8 ; +} + +struct ipath_mcast *ipath_mcast_find (union ib_gid *mgid); + +int ipath_multicast_attach (struct ib_qp *ibqp,union ib_gid *gid,u16 lid); + +int ipath_multicast_detach (struct ib_qp *ibqp,union ib_gid *gid,u16 lid); + +int ipath_mcast_tree_empty (void ); + +__be32 ipath_compute_aeth (struct ipath_qp *qp); + +struct ipath_qp *ipath_lookup_qpn (struct ipath_qp_table *qpt,u32 qpn); + +struct ib_qp *ipath_create_qp (struct ib_pd *ibpd, +struct ib_qp_init_attr *init_attr, +struct ib_udata *udata); + +int ipath_destroy_qp (struct ib_qp *ibqp); + +int ipath_modify_qp (struct ib_qp *ibqp,struct ib_qp_attr *attr, +int attr_mask); + +int ipath_query_qp (struct ib_qp *ibqp,struct ib_qp_attr *attr, +int attr_mask,struct ib_qp_init_attr *init_attr); + +void ipath_free_all_qps (struct ipath_qp_table *qpt); + +int ipath_init_qp_table (struct ipath_ibdev *idev,int size); + +void ipath_sqerror_qp (struct ipath_qp *qp,struct ib_wc *wc); + +void ipath_error_qp (struct ipath_qp *qp); + +void ipath_get_credit (struct ipath_qp *qp,u32 aeth); + +void ipath_do_rc_send (unsigned long data); + +void ipath_do_uc_send (unsigned long data); + +void ipath_cq_enter (struct ipath_cq *cq,struct ib_wc *entry,int sig); + +int ipath_rkey_ok (struct ipath_ibdev *dev,struct ipath_sge_state *ss, +u32 len,u64 vaddr,u32 rkey,int acc); + +int ipath_lkey_ok (struct ipath_lkey_table *rkt,struct ipath_sge *isge, +struct ib_sge *sge,int acc); + +void ipath_copy_sge (struct ipath_sge_state *ss,void *data,u32 length); + +void ipath_skip_sge (struct ipath_sge_state *ss,u32 length); + +int ipath_post_rc_send (struct ipath_qp *qp,struct ib_send_wr *wr); + +void ipath_uc_rcv (struct ipath_ibdev *dev,struct ipath_ib_header *hdr, +int has_grh,void *data,u32 tlen,struct ipath_qp *qp); + +void ipath_rc_rcv (struct ipath_ibdev *dev,struct ipath_ib_header *hdr, +int has_grh,void *data,u32 tlen,struct ipath_qp *qp); + +void ipath_restart_rc (struct ipath_qp *qp,u32 psn,struct ib_wc *wc); + +void ipath_ud_loopback (struct ipath_qp *sqp,struct ipath_sge_state *ss, +u32 length,struct ib_send_wr *wr,struct ib_wc *wc); + +int ipath_post_ud_send (struct ipath_qp *qp,struct ib_send_wr *wr); + +void ipath_ud_rcv (struct ipath_ibdev *dev,struct ipath_ib_header *hdr, +int has_grh,void *data,u32 tlen,struct ipath_qp *qp); + +int ipath_alloc_lkey (struct ipath_lkey_table *rkt, +struct ipath_mregion *mr); + +void ipath_free_lkey (struct ipath_lkey_table *rkt,u32 lkey); + +int ipath_lkey_ok (struct ipath_lkey_table *rkt,struct ipath_sge *isge, +struct ib_sge *sge,int acc); + +int ipath_rkey_ok (struct ipath_ibdev *dev,struct ipath_sge_state *ss, +u32 len,u64 vaddr,u32 rkey,int acc); + +int ipath_post_srq_receive (struct ib_srq *ibsrq,struct ib_recv_wr *wr, +struct ib_recv_wr **bad_wr); + +struct ib_srq *ipath_create_srq (struct ib_pd *ibpd, +struct ib_srq_init_attr *srq_init_attr, +struct ib_udata *udata); + +int ipath_modify_srq (struct ib_srq *ibsrq,struct ib_srq_attr *attr, +enum ib_srq_attr_mask attr_mask); + +int ipath_query_srq (struct ib_srq *ibsrq,struct ib_srq_attr *attr); + +int ipath_destroy_srq (struct ib_srq *ibsrq); + +void ipath_cq_enter (struct ipath_cq *cq,struct ib_wc *entry,int sig); + +int ipath_poll_cq (struct ib_cq *ibcq,int num_entries,struct ib_wc *entry); + +struct ib_cq *ipath_create_cq (struct ib_device *ibdev,int entries, +struct ib_ucontext *context, +struct ib_udata *udata); + +int ipath_destroy_cq (struct ib_cq *ibcq); + +int ipath_req_notify_cq (struct ib_cq *ibcq,enum ib_cq_notify notify); + +int ipath_resize_cq (struct ib_cq *ibcq,int cqe,struct ib_udata *udata); + +struct ib_mr *ipath_get_dma_mr (struct ib_pd *pd,int acc); + +struct ib_mr *ipath_reg_phys_mr (struct ib_pd *pd, +struct ib_phys_buf *buffer_list, +int num_phys_buf,int acc,u64 *iova_start); + +struct ib_mr *ipath_reg_user_mr (struct ib_pd *pd,struct ib_umem *region, +int mr_access_flags, +struct ib_udata *udata); + +int ipath_dereg_mr (struct ib_mr *ibmr); + +struct ib_fmr *ipath_alloc_fmr (struct ib_pd *pd,int mr_access_flags, +struct ib_fmr_attr *fmr_attr); + +int ipath_map_phys_fmr (struct ib_fmr *ibfmr,u64 * page_list, +int list_len,u64 iova); + +int ipath_unmap_fmr (struct list_head *fmr_list); + +int ipath_dealloc_fmr (struct ib_fmr *ibfmr); + +void ipath_no_bufs_available (struct ipath_qp *qp,struct ipath_ibdev *dev); + +void ipath_insert_rnr_queue (struct ipath_qp *qp); + +int ipath_get_rwqe (struct ipath_qp *qp,int wr_id_only); + +void ipath_ruc_loopback (struct ipath_qp *sqp,struct ib_wc *wc); + +extern const enum ib_wc_opcode ib_ipath_wc_opcode[]; + +extern const u8 ipath_cvt_physportstate[]; + +extern const int ib_ipath_state_ops[]; + +extern unsigned int ib_ipath_lkey_table_size; + +extern const u32 ib_ipath_rnr_table[]; + +#endif /* IPATH_VERBS_H */
drivers/infiniband/hw/ipath/verbs_debug.h new file +107 -0
107 lines not on this page · raw message
PATCH 1/1 ipath - infiniband UC and UD protocol support
In reply to Bryan O'SullivanThese files implement the Infiniband UC ("unreliable connection") and UD ("unreliable datagram") protocols.
drivers/infiniband/hw/ipath/ipath_uc.c new file +645 -0
@@ -0,0 +1,645 @@ +/* +* Copyright (c) 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include "ipath_verbs.h" +#include "ips_common.h" + +/* cut down ridiculously long IB macro names */ +#define OP (x) IB_OPCODE_UC_##x + +static void complete_last_send (struct ipath_qp *qp,struct ipath_swqe *wqe, +struct ib_wc *wc) +{ +if (++qp->s_last == qp->s_size) + qp->s_last =0 ; +if (!test_bit (IPATH_S_SIGNAL_REQ_WR , &qp->s_flags) || + (wqe->wr.send_flags &IB_SEND_SIGNALED )) { + wc->wr_id = wqe->wr.wr_id; + wc->status =IB_WC_SUCCESS ; + wc->opcode = ib_ipath_wc_opcode[wqe->wr.opcode]; + wc->vendor_err =0 ; + wc->byte_len = wqe->length; + wc->qp_num = qp->ibqp.qp_num; + wc->src_qp = qp->remote_qpn; + wc->pkey_index =0 ; + wc->slid = qp->remote_ah_attr.dlid; + wc->sl = qp->remote_ah_attr.sl; + wc->dlid_path_bits =0 ; + wc->port_num =0 ; +ipath_cq_enter (to_icq (qp->ibqp.send_cq), wc,0 ); + } + wqe =get_swqe_ptr (qp, qp->s_last); +} + +/** +* ipath_do_uc_send - do a send on a UC queue +* @data: contains a pointer to the QP to send on +* +* Process entries in the send work queue until the queue is exhausted. +* Only allow one CPU to send a packet per QP (tasklet). +* Otherwise, after we drop the QP lock, two threads could send +* packets out of order. +* This is similar to ipath_do_rc_send() below except we don't have +* timeouts or resends. +*/ +void ipath_do_uc_send (unsigned long data) +{ +struct ipath_qp *qp = (struct ipath_qp *)data; +struct ipath_ibdev *dev =to_idev (qp->ibqp.device); +struct ipath_swqe *wqe; +unsigned long flags; +u16 lrh0; +u32 hwords; +u32 nwords; +u32 extra_bytes; +u32 bth0; +u32 bth2; +u32 pmtu =ib_mtu_enum_to_int (qp->path_mtu); +u32 len; +struct ipath_other_headers *ohdr; +struct ib_wc wc; + +if (test_and_set_bit (IPATH_S_BUSY , &qp->s_flags)) + goto bail; + +if (unlikely (qp->remote_ah_attr.dlid == +ipath_layer_get_lid (dev->dd))) { +/* Pass in an uninitialized ib_wc to save stack space. */ +ipath_ruc_loopback (qp, &wc); +clear_bit (IPATH_S_BUSY , &qp->s_flags); + goto bail; + } + + ohdr = &qp->s_hdr.u.oth; +if (qp->remote_ah_attr.ah_flags &IB_AH_GRH ) + ohdr = &qp->s_hdr.u.l.oth; + +again: +/* Check for a constructed packet to be sent. */ +if (qp->s_hdrwords !=0 ) { +/* +* If no PIO bufs are available, return. +* An interrupt will call ipath_ib_piobufavail() +* when one is available. +*/ +if (ipath_verbs_send (dev->dd, qp->s_hdrwords, + (u32 *) &qp->s_hdr, + qp->s_cur_size, + qp->s_cur_sge)) { +ipath_no_bufs_available (qp, dev); + goto bail; + } + dev->n_unicast_xmit++; +/* Record that we sent the packet and s_hdr is empty. */ + qp->s_hdrwords =0 ; + } + + lrh0 =IPS_LRH_BTH ; +/* header size in 32-bit words LRH+BTH = (8+12)/4. */ + hwords =5 ; + +/* +* The lock is needed to synchronize between +* setting qp->s_ack_state and post_send(). +*/ +spin_lock_irqsave (&qp->s_lock, flags); + +if (!(ib_ipath_state_ops[qp->state] &IPATH_PROCESS_SEND_OK )) + goto done; + + bth0 =ipath_layer_get_pkey (dev->dd, qp->s_pkey_index); + +/* Send a request. */ + wqe =get_swqe_ptr (qp, qp->s_last); +switch (qp->s_state) { +default : +/* +* Signal the completion of the last send (if there is +* one). +*/ +if (qp->s_last != qp->s_tail) +complete_last_send (qp, wqe, &wc); + +/* Check if send work queue is empty. */ +if (qp->s_tail == qp->s_head) + goto done; +/* +* Start a new request. +*/ + qp->s_psn = wqe->psn = qp->s_next_psn; + qp->s_sge.sge = wqe->sg_list[0 ]; + qp->s_sge.sg_list = wqe->sg_list +1 ; + qp->s_sge.num_sge = wqe->wr.num_sge; + qp->s_len = len = wqe->length; +switch (wqe->wr.opcode) { +case IB_WR_SEND : +case IB_WR_SEND_WITH_IMM : +if (len > pmtu) { + qp->s_state =OP (SEND_FIRST ); + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_SEND ) + qp->s_state =OP (SEND_ONLY ); +else { + qp->s_state = +OP (SEND_ONLY_WITH_IMMEDIATE ); +/* Immediate data comes after the BTH */ + ohdr->u.imm_data = wqe->wr.imm_data; + hwords +=1 ; + } +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; +break ; + +case IB_WR_RDMA_WRITE : +case IB_WR_RDMA_WRITE_WITH_IMM : + ohdr->u.rc.reth.vaddr = +cpu_to_be64 (wqe->wr.wr.rdma.remote_addr); + ohdr->u.rc.reth.rkey = +cpu_to_be32 (wqe->wr.wr.rdma.rkey); + ohdr->u.rc.reth.length =cpu_to_be32 (len); + hwords +=sizeof (struct ib_reth ) /4 ; +if (len > pmtu) { + qp->s_state =OP (RDMA_WRITE_FIRST ); + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_RDMA_WRITE ) + qp->s_state =OP (RDMA_WRITE_ONLY ); +else { + qp->s_state = +OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE ); +/* Immediate data comes after the RETH */ + ohdr->u.rc.imm_data = wqe->wr.imm_data; + hwords +=1 ; +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; + } +break ; + +default : + goto done; + } +if (++qp->s_tail >= qp->s_size) + qp->s_tail =0 ; +break ; + +case OP (SEND_FIRST ): + qp->s_state =OP (SEND_MIDDLE ); +/* FALLTHROUGH */ +case OP (SEND_MIDDLE ): + len = qp->s_len; +if (len > pmtu) { + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_SEND ) + qp->s_state =OP (SEND_LAST ); +else { + qp->s_state =OP (SEND_LAST_WITH_IMMEDIATE ); +/* Immediate data comes after the BTH */ + ohdr->u.imm_data = wqe->wr.imm_data; + hwords +=1 ; + } +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; +break ; + +case OP (RDMA_WRITE_FIRST ): + qp->s_state =OP (RDMA_WRITE_MIDDLE ); +/* FALLTHROUGH */ +case OP (RDMA_WRITE_MIDDLE ): + len = qp->s_len; +if (len > pmtu) { + len = pmtu; +break ; + } +if (wqe->wr.opcode ==IB_WR_RDMA_WRITE ) + qp->s_state =OP (RDMA_WRITE_LAST ); +else { + qp->s_state = +OP (RDMA_WRITE_LAST_WITH_IMMEDIATE ); +/* Immediate data comes after the BTH */ + ohdr->u.imm_data = wqe->wr.imm_data; + hwords +=1 ; +if (wqe->wr.send_flags &IB_SEND_SOLICITED ) + bth0 |=1 <<23 ; + } +break ; + } + bth2 = qp->s_next_psn++ &IPS_PSN_MASK ; + qp->s_len -= len; + bth0 |= qp->s_state <<24 ; + +spin_unlock_irqrestore (&qp->s_lock, flags); + +/* Construct the header. */ + extra_bytes = (4 - len) &3 ; + nwords = (len + extra_bytes) >>2 ; +if (unlikely (qp->remote_ah_attr.ah_flags &IB_AH_GRH )) { +/* Header size in 32-bit words. */ + hwords +=10 ; + lrh0 =IPS_LRH_GRH ; + qp->s_hdr.u.l.grh.version_tclass_flow = +cpu_to_be32 ((6 <<28 ) | + (qp->remote_ah_attr.grh.traffic_class + <<20 ) | + qp->remote_ah_attr.grh.flow_label); + qp->s_hdr.u.l.grh.paylen = +cpu_to_be16 (((hwords -12 ) + nwords + +SIZE_OF_CRC ) <<2 ); +/* next_hdr is defined by C8-7 in ch. 8.4.1 */ + qp->s_hdr.u.l.grh.next_hdr =0x1B ; + qp->s_hdr.u.l.grh.hop_limit = + qp->remote_ah_attr.grh.hop_limit; +/* The SGID is 32-bit aligned. */ + qp->s_hdr.u.l.grh.sgid.global.subnet_prefix = + dev->gid_prefix; + qp->s_hdr.u.l.grh.sgid.global.interface_id = +ipath_layer_get_guid (dev->dd); + qp->s_hdr.u.l.grh.dgid = qp->remote_ah_attr.grh.dgid; + } + qp->s_hdrwords = hwords; + qp->s_cur_sge = &qp->s_sge; + qp->s_cur_size = len; + lrh0 |= qp->remote_ah_attr.sl <<4 ; + qp->s_hdr.lrh[0 ] =cpu_to_be16 (lrh0); +/* DEST LID */ + qp->s_hdr.lrh[1 ] =cpu_to_be16 (qp->remote_ah_attr.dlid); + qp->s_hdr.lrh[2 ] =cpu_to_be16 (hwords + nwords +SIZE_OF_CRC ); + qp->s_hdr.lrh[3 ] =cpu_to_be16 (ipath_layer_get_lid (dev->dd)); + bth0 |= extra_bytes <<20 ; + ohdr->bth[0 ] =cpu_to_be32 (bth0); + ohdr->bth[1 ] =cpu_to_be32 (qp->remote_qpn); + ohdr->bth[2 ] =cpu_to_be32 (bth2); + +/* Check for more work to do. */ + goto again; + +done: +spin_unlock_irqrestore (&qp->s_lock, flags); +clear_bit (IPATH_S_BUSY , &qp->s_flags); + +bail: +return ; +} + +/** +* ipath_uc_rcv - handle an incoming UC packet +* @dev: the device the packet came in on +* @hdr: the header of the packet +* @has_grh: true if the packet has a GRH +* @data: the packet data +* @tlen: the length of the packet +* @qp: the QP for this packet. +* +* This is called from ipath_qp_rcv() to process an incoming UC packet +* for the given QP. +* Called at interrupt level. +*/ +void ipath_uc_rcv (struct ipath_ibdev *dev,struct ipath_ib_header *hdr, +int has_grh,void *data,u32 tlen,struct ipath_qp *qp) +{ +struct ipath_other_headers *ohdr; +int opcode; +u32 hdrsize; +u32 psn; +u32 pad; +unsigned long flags; +struct ib_wc wc; +u32 pmtu =ib_mtu_enum_to_int (qp->path_mtu); +struct ib_reth *reth; +int header_in_data; + +/* Check for GRH */ +if (!has_grh) { + ohdr = &hdr->u.oth; + hdrsize =8 +12 ;/* LRH + BTH */ + psn =be32_to_cpu (ohdr->bth[2 ]); + header_in_data =0 ; + }else { + ohdr = &hdr->u.l.oth; + hdrsize =8 +40 +12 ;/* LRH + GRH + BTH */ +/* +* The header with GRH is 60 bytes and the +* core driver sets the eager header buffer +* size to 56 bytes so the last 4 bytes of +* the BTH header (PSN) is in the data buffer. +*/ + header_in_data = +ipath_layer_get_rcvhdrentsize (dev->dd) ==16 ; +if (header_in_data) { + psn =be32_to_cpu (((__be32 *) data)[0 ]); + data +=sizeof (__be32); + }else + psn =be32_to_cpu (ohdr->bth[2 ]); + } +/* +* The opcode is in the low byte when its in network order +* (top byte when in host order). +*/ + opcode =be32_to_cpu (ohdr->bth[0 ]) >>24 ; + + wc.imm_data =0 ; + wc.wc_flags =0 ; + +spin_lock_irqsave (&qp->r_rq.lock, flags); + +/* Compare the PSN verses the expected PSN. */ +if (unlikely (ipath_cmp24 (psn, qp->r_psn) !=0 )) { +/* +* Handle a sequence error. +* Silently drop any current message. +*/ + qp->r_psn = psn; + inv: + qp->r_state =OP (SEND_LAST ); +switch (opcode) { +case OP (SEND_FIRST ): +case OP (SEND_ONLY ): +case OP (SEND_ONLY_WITH_IMMEDIATE ): + goto send_first; + +case OP (RDMA_WRITE_FIRST ): +case OP (RDMA_WRITE_ONLY ): +case OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE ): + goto rdma_first; + +default : + dev->n_pkt_drops++; + goto done; + } + } + +/* Check for opcode sequence errors. */ +switch (qp->r_state) { +case OP (SEND_FIRST ): +case OP (SEND_MIDDLE ): +if (opcode ==OP (SEND_MIDDLE ) || + opcode ==OP (SEND_LAST ) || + opcode ==OP (SEND_LAST_WITH_IMMEDIATE )) +break ; + goto inv; + +case OP (RDMA_WRITE_FIRST ): +case OP (RDMA_WRITE_MIDDLE ): +if (opcode ==OP (RDMA_WRITE_MIDDLE ) || + opcode ==OP (RDMA_WRITE_LAST ) || + opcode ==OP (RDMA_WRITE_LAST_WITH_IMMEDIATE )) +break ; + goto inv; + +default : +if (opcode ==OP (SEND_FIRST ) || + opcode ==OP (SEND_ONLY ) || + opcode ==OP (SEND_ONLY_WITH_IMMEDIATE ) || + opcode ==OP (RDMA_WRITE_FIRST ) || + opcode ==OP (RDMA_WRITE_ONLY ) || + opcode ==OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE )) +break ; + goto inv; + } + +/* OK, process the packet. */ +switch (opcode) { +case OP (SEND_FIRST ): +case OP (SEND_ONLY ): +case OP (SEND_ONLY_WITH_IMMEDIATE ): + send_first: +if (qp->r_reuse_sge) { + qp->r_reuse_sge =0 ; + qp->r_sge = qp->s_rdma_sge; + }else if (!ipath_get_rwqe (qp,0 )) { + dev->n_pkt_drops++; + goto done; + } +/* Save the WQE so we can reuse it in case of an error. */ + qp->s_rdma_sge = qp->r_sge; + qp->r_rcv_len =0 ; +if (opcode ==OP (SEND_ONLY )) + goto send_last; +else if (opcode ==OP (SEND_ONLY_WITH_IMMEDIATE )) + goto send_last_imm; +/* FALLTHROUGH */ +case OP (SEND_MIDDLE ): +/* Check for invalid length PMTU or posted rwqe len. */ +if (unlikely (tlen != (hdrsize + pmtu +4 ))) { + qp->r_reuse_sge =1 ; + dev->n_pkt_drops++; + goto done; + } + qp->r_rcv_len += pmtu; +if (unlikely (qp->r_rcv_len > qp->r_len)) { + qp->r_reuse_sge =1 ; + dev->n_pkt_drops++; + goto done; + } +ipath_copy_sge (&qp->r_sge, data, pmtu); +break ; + +case OP (SEND_LAST_WITH_IMMEDIATE ): + send_last_imm: +if (header_in_data) { + wc.imm_data = *(__be32 *) data; + data +=sizeof (__be32); + }else { +/* Immediate data comes after BTH */ + wc.imm_data = ohdr->u.imm_data; + } + hdrsize +=4 ; + wc.wc_flags =IB_WC_WITH_IMM ; +/* FALLTHROUGH */ +case OP (SEND_LAST ): + send_last: +/* Get the number of bytes the message was padded by. */ + pad = (be32_to_cpu (ohdr->bth[0 ]) >>20 ) &3 ; +/* Check for invalid length. */ +/* XXX LAST len should be >= 1 */ +if (unlikely (tlen < (hdrsize + pad +4 ))) { + qp->r_reuse_sge =1 ; + dev->n_pkt_drops++; + goto done; + } +/* Don't count the CRC. */ + tlen -= (hdrsize + pad +4 ); + wc.byte_len = tlen + qp->r_rcv_len; +if (unlikely (wc.byte_len > qp->r_len)) { + qp->r_reuse_sge =1 ; + dev->n_pkt_drops++; + goto done; + } +/* XXX Need to free SGEs */ + last_imm: +ipath_copy_sge (&qp->r_sge, data, tlen); + wc.wr_id = qp->r_wr_id; + wc.status =IB_WC_SUCCESS ; + wc.opcode =IB_WC_RECV ; + wc.vendor_err =0 ; + wc.qp_num = qp->ibqp.qp_num; + wc.src_qp = qp->remote_qpn; + wc.pkey_index =0 ; + wc.slid = qp->remote_ah_attr.dlid; + wc.sl = qp->remote_ah_attr.sl; + wc.dlid_path_bits =0 ; + wc.port_num =0 ; +/* Signal completion event if the solicited bit is set. */ +ipath_cq_enter (to_icq (qp->ibqp.recv_cq), &wc, + (ohdr->bth[0 ] & +__constant_cpu_to_be32 (1 <<23 )) !=0 ); +break ; + +case OP (RDMA_WRITE_FIRST ): +case OP (RDMA_WRITE_ONLY ): +case OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE ):/* consume RWQE */ + rdma_first: +/* RETH comes after BTH */ +if (!header_in_data) + reth = &ohdr->u.rc.reth; +else { + reth = (struct ib_reth *)data; + data +=sizeof (*reth); + } + hdrsize +=sizeof (*reth); + qp->r_len =be32_to_cpu (reth->length); + qp->r_rcv_len =0 ; +if (qp->r_len !=0 ) { +u32 rkey =be32_to_cpu (reth->rkey); +u64 vaddr =be64_to_cpu (reth->vaddr); + +/* Check rkey */ +if (unlikely (!ipath_rkey_ok ( + dev, &qp->r_sge, qp->r_len, + vaddr, rkey, +IB_ACCESS_REMOTE_WRITE ))) { + dev->n_pkt_drops++; + goto done; + } + }else { + qp->r_sge.sg_list =NULL ; + qp->r_sge.sge.mr =NULL ; + qp->r_sge.sge.vaddr =NULL ; + qp->r_sge.sge.length =0 ; + qp->r_sge.sge.sge_length =0 ; + } +if (unlikely (!(qp->qp_access_flags & +IB_ACCESS_REMOTE_WRITE ))) { + dev->n_pkt_drops++; + goto done; + } +if (opcode ==OP (RDMA_WRITE_ONLY )) + goto rdma_last; +else if (opcode == +OP (RDMA_WRITE_ONLY_WITH_IMMEDIATE )) + goto rdma_last_imm; +/* FALLTHROUGH */ +case OP (RDMA_WRITE_MIDDLE ): +/* Check for invalid length PMTU or posted rwqe len. */ +if (unlikely (tlen != (hdrsize + pmtu +4 ))) { + dev->n_pkt_drops++; + goto done; + } + qp->r_rcv_len += pmtu; +if (unlikely (qp->r_rcv_len > qp->r_len)) { + dev->n_pkt_drops++; + goto done; + } +ipath_copy_sge (&qp->r_sge, data, pmtu); +break ; + +case OP (RDMA_WRITE_LAST_WITH_IMMEDIATE ): + rdma_last_imm: +/* Get the number of bytes the message was padded by. */ + pad = (be32_to_cpu (ohdr->bth[0 ]) >>20 ) &3 ; +/* Check for invalid length. */ +/* XXX LAST len should be >= 1 */ +if (unlikely (tlen < (hdrsize + pad +4 ))) { + dev->n_pkt_drops++; + goto done; + } +/* Don't count the CRC. */ + tlen -= (hdrsize + pad +4 ); +if (unlikely (tlen + qp->r_rcv_len != qp->r_len)) { + dev->n_pkt_drops++; + goto done; + } +if (qp->r_reuse_sge) { + qp->r_reuse_sge =0 ; + }else if (!ipath_get_rwqe (qp,1 )) { + dev->n_pkt_drops++; + goto done; + } +if (header_in_data) { + wc.imm_data = *(__be32 *) data; + data +=sizeof (__be32); + }else { +/* Immediate data comes after BTH */ + wc.imm_data = ohdr->u.imm_data; + } + hdrsize +=4 ; + wc.wc_flags =IB_WC_WITH_IMM ; + wc.byte_len =0 ; + goto last_imm; + +case OP (RDMA_WRITE_LAST ): + rdma_last: +/* Get the number of bytes the message was padded by. */ + pad = (be32_to_cpu (ohdr->bth[0 ]) >>20 ) &3 ; +/* Check for invalid length. */ +/* XXX LAST len should be >= 1 */ +if (unlikely (tlen < (hdrsize + pad +4 ))) { + dev->n_pkt_drops++; + goto done; + } +/* Don't count the CRC. */ + tlen -= (hdrsize + pad +4 ); +if (unlikely (tlen + qp->r_rcv_len != qp->r_len)) { + dev->n_pkt_drops++; + goto done; + } +ipath_copy_sge (&qp->r_sge, data, tlen); +break ; + +default : +/* Drop packet for unknown opcodes. */ +spin_unlock_irqrestore (&qp->r_rq.lock, flags); + dev->n_pkt_drops++; + goto bail; + } + qp->r_psn++; + qp->r_state = opcode; +done: +spin_unlock_irqrestore (&qp->r_rq.lock, flags); + +bail: +return ; +}
drivers/infiniband/hw/ipath/ipath_ud.c new file +621 -0
621 lines not on this page · raw message
PATCH 1/1 ipath - layering interfaces used by higher-level driver code
In reply to Bryan O'SullivanThe layering interfaces are used to implement the Infiniband protocols and the ethernet emulation driver.
drivers/infiniband/hw/ipath/ipath_layer.c new file +1515 -0
@@ -0,0 +1,1515 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +/* +* These are the routines used by layered drivers, currently just the +* layered ethernet driver and verbs layer. +*/ + +#include <linux/io.h> +#include <linux/pci.h> +#include <asm/byteorder.h> + +#include "ipath_kernel.h" +#include "ips_common.h" +#include "ipath_layer.h" + +/* Acquire before ipath_devs_lock. */ +static DEFINE_MUTEX (ipath_layer_mutex); + +u16 ipath_layer_rcv_opcode; +static int (*layer_intr)(void *,u32 ); +static int (*layer_rcv)(void *,void *,struct sk_buff *); +static int (*layer_rcv_lid)(void *,void *); +static int (*verbs_piobufavail)(void *); +static void (*verbs_rcv)(void *,void *,void *,u32 ); +int ipath_verbs_registered; + +static void *(*layer_add_one)(int ,struct ipath_devdata *); +static void (*layer_remove_one)(void *); +static void *(*verbs_add_one)(int ,struct ipath_devdata *); +static void (*verbs_remove_one)(void *); +static void (*verbs_timer_cb)(void *); + +int __ipath_layer_intr (struct ipath_devdata *dd,u32 arg) +{ +int ret = -ENODEV ; + +if (dd->ipath_layer.l_arg && layer_intr) + ret =layer_intr (dd->ipath_layer.l_arg, arg); + +return ret; +} + +int ipath_layer_intr (struct ipath_devdata *dd,u32 arg) +{ +int ret; + +mutex_lock (&ipath_layer_mutex); + + ret =__ipath_layer_intr (dd, arg); + +mutex_unlock (&ipath_layer_mutex); + +return ret; +} + +int __ipath_layer_rcv (struct ipath_devdata *dd,void *hdr, +struct sk_buff *skb) +{ +int ret = -ENODEV ; + +if (dd->ipath_layer.l_arg && layer_rcv) + ret =layer_rcv (dd->ipath_layer.l_arg, hdr, skb); + +return ret; +} + +int __ipath_layer_rcv_lid (struct ipath_devdata *dd,void *hdr) +{ +int ret = -ENODEV ; + +if (dd->ipath_layer.l_arg && layer_rcv_lid) + ret =layer_rcv_lid (dd->ipath_layer.l_arg, hdr); + +return ret; +} + +int __ipath_verbs_piobufavail (struct ipath_devdata *dd) +{ +int ret = -ENODEV ; + +if (dd->verbs_layer.l_arg && verbs_piobufavail) + ret =verbs_piobufavail (dd->verbs_layer.l_arg); + +return ret; +} + +int __ipath_verbs_rcv (struct ipath_devdata *dd,void *rc,void *ebuf, +u32 tlen) +{ +int ret = -ENODEV ; + +if (dd->verbs_layer.l_arg && verbs_rcv) { +verbs_rcv (dd->verbs_layer.l_arg, rc, ebuf, tlen); + ret =0 ; + } + +return ret; +} + +int ipath_layer_set_linkstate (struct ipath_devdata *dd,u8 newstate) +{ +u32 lstate; +int ret; + +switch (newstate) { +case IPATH_IB_LINKDOWN : +ipath_set_ib_lstate (dd,INFINIPATH_IBCC_LINKINITCMD_POLL << +INFINIPATH_IBCC_LINKINITCMD_SHIFT ); +/* don't wait */ + ret =0 ; + goto bail; + +case IPATH_IB_LINKDOWN_SLEEP : +ipath_set_ib_lstate (dd,INFINIPATH_IBCC_LINKINITCMD_SLEEP << +INFINIPATH_IBCC_LINKINITCMD_SHIFT ); +/* don't wait */ + ret =0 ; + goto bail; + +case IPATH_IB_LINKDOWN_DISABLE : +ipath_set_ib_lstate (dd, +INFINIPATH_IBCC_LINKINITCMD_DISABLE << +INFINIPATH_IBCC_LINKINITCMD_SHIFT ); +/* don't wait */ + ret =0 ; + goto bail; + +case IPATH_IB_LINKINIT : +if (dd->ipath_flags &IPATH_LINKINIT ) { + ret =0 ; + goto bail; + } +ipath_set_ib_lstate (dd,INFINIPATH_IBCC_LINKCMD_INIT << +INFINIPATH_IBCC_LINKCMD_SHIFT ); + lstate =IPATH_LINKINIT ; +break ; + +case IPATH_IB_LINKARM : +if (dd->ipath_flags &IPATH_LINKARMED ) { + ret =0 ; + goto bail; + } +if (!(dd->ipath_flags & + (IPATH_LINKINIT |IPATH_LINKACTIVE ))) { + ret = -EINVAL ; + goto bail; + } +ipath_set_ib_lstate (dd,INFINIPATH_IBCC_LINKCMD_ARMED << +INFINIPATH_IBCC_LINKCMD_SHIFT ); +/* +* Since the port can transition to ACTIVE by receiving +* a non VL 15 packet, wait for either state. +*/ + lstate =IPATH_LINKARMED |IPATH_LINKACTIVE ; +break ; + +case IPATH_IB_LINKACTIVE : +if (dd->ipath_flags &IPATH_LINKACTIVE ) { + ret =0 ; + goto bail; + } +if (!(dd->ipath_flags &IPATH_LINKARMED )) { + ret = -EINVAL ; + goto bail; + } +ipath_set_ib_lstate (dd,INFINIPATH_IBCC_LINKCMD_ACTIVE << +INFINIPATH_IBCC_LINKCMD_SHIFT ); + lstate =IPATH_LINKACTIVE ; +break ; + +default : +ipath_dbg ("Invalid linkstate 0x%x requested\n" , newstate); + ret = -EINVAL ; + goto bail; + } + ret =ipath_wait_linkstate (dd, lstate,2000 ); + +bail: +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_linkstate); + +/** +* ipath_layer_set_mtu - set the MTU +* @dd: the infinipath device +* @arg: the new MTU +* +* we can handle "any" incoming size, the issue here is whether we +* need to restrict our outgoing size. For now, we don't do any +* sanity checking on this, and we don't deal with what happens to +* programs that are already running when the size changes. +* NOTE: changing the MTU will usually cause the IBC to go back to +* link initialize (IPATH_IBSTATE_INIT) state... +*/ +int ipath_layer_set_mtu (struct ipath_devdata *dd,u16 arg) +{ +u32 piosize; +int changed =0 ; +int ret; + +/* +* mtu is IB data payload max. It's the largest power of 2 less +* than piosize (or even larger, since it only really controls the +* largest we can receive; we can send the max of the mtu and +* piosize). We check that it's one of the valid IB sizes. +*/ +if (arg !=256 && arg !=512 && arg !=1024 && arg !=2048 && + arg !=4096 ) { +ipath_dbg ("Trying to set invalid mtu %u, failing\n" , arg); + ret = -EINVAL ; + goto bail; + } +if (dd->ipath_ibmtu == arg) { + ret =0 ;/* same as current */ + goto bail; + } + + piosize = dd->ipath_ibmaxlen; + dd->ipath_ibmtu = arg; + +if (arg >= (piosize -IPATH_PIO_MAXIBHDR )) { +/* Only if it's not the initial value (or reset to it) */ +if (piosize != dd->ipath_init_ibmaxlen) { + dd->ipath_ibmaxlen = piosize; + changed =1 ; + } + }else if ((arg +IPATH_PIO_MAXIBHDR ) != dd->ipath_ibmaxlen) { + piosize = arg +IPATH_PIO_MAXIBHDR ; +ipath_cdbg (VERBOSE ,"ibmaxlen was 0x%x, setting to 0x%x " +"(mtu 0x%x)\n" , dd->ipath_ibmaxlen, piosize, + arg); + dd->ipath_ibmaxlen = piosize; + changed =1 ; + } + +if (changed) { +/* +* set the IBC maxpktlength to the size of our pio +* buffers in words +*/ +u64 ibc = dd->ipath_ibcctrl; + ibc &= ~(INFINIPATH_IBCC_MAXPKTLEN_MASK << +INFINIPATH_IBCC_MAXPKTLEN_SHIFT ); + + piosize = piosize -2 *sizeof (u32);/* ignore pbc */ + dd->ipath_ibmaxlen = piosize; + piosize /=sizeof (u32);/* in words */ +/* +* for ICRC, which we only send in diag test pkt mode, and +* we don't need to worry about that for mtu +*/ + piosize +=1 ; + + ibc |= piosize <<INFINIPATH_IBCC_MAXPKTLEN_SHIFT ; + dd->ipath_ibcctrl = ibc; +ipath_write_kreg (dd, dd->ipath_kregs->kr_ibcctrl, + dd->ipath_ibcctrl); + dd->ipath_f_tidtemplate (dd); + } + + ret =0 ; + +bail: +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_mtu); + +int ipath_set_sps_lid (struct ipath_devdata *dd,u32 arg,u8 lmc) +{ + ipath_stats.sps_lid[dd->ipath_unit] = arg; + dd->ipath_lid = arg; + dd->ipath_lmc = lmc; + +mutex_lock (&ipath_layer_mutex); + +if (dd->ipath_layer.l_arg && layer_intr) +layer_intr (dd->ipath_layer.l_arg,IPATH_LAYER_INT_LID ); + +mutex_unlock (&ipath_layer_mutex); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_set_sps_lid); + +int ipath_layer_set_guid (struct ipath_devdata *dd,__be64 guid) +{ +/* XXX - need to inform anyone who cares this just happened. */ + dd->ipath_guid = guid; +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_guid); + +__be64 ipath_layer_get_guid (struct ipath_devdata *dd) +{ +return dd->ipath_guid; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_guid); + +u32 ipath_layer_get_nguid (struct ipath_devdata *dd) +{ +return dd->ipath_nguid; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_nguid); + +int ipath_layer_query_device (struct ipath_devdata *dd,u32 * vendor, +u32 * boardrev,u32 * majrev,u32 * minrev) +{ + *vendor = dd->ipath_vendorid; + *boardrev = dd->ipath_boardrev; + *majrev = dd->ipath_majrev; + *minrev = dd->ipath_minrev; + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_query_device); + +u32 ipath_layer_get_flags (struct ipath_devdata *dd) +{ +return dd->ipath_flags; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_flags); + +struct device *ipath_layer_get_device (struct ipath_devdata *dd) +{ +return &dd->pcidev->dev; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_device); + +u16 ipath_layer_get_deviceid (struct ipath_devdata *dd) +{ +return dd->ipath_deviceid; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_deviceid); + +u64 ipath_layer_get_lastibcstat (struct ipath_devdata *dd) +{ +return dd->ipath_lastibcstat; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_lastibcstat); + +u32 ipath_layer_get_ibmtu (struct ipath_devdata *dd) +{ +return dd->ipath_ibmtu; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_ibmtu); + +void ipath_layer_add (struct ipath_devdata *dd) +{ +mutex_lock (&ipath_layer_mutex); + +if (layer_add_one) + dd->ipath_layer.l_arg = +layer_add_one (dd->ipath_unit, dd); + +if (verbs_add_one) + dd->verbs_layer.l_arg = +verbs_add_one (dd->ipath_unit, dd); + +mutex_unlock (&ipath_layer_mutex); +} + +void ipath_layer_del (struct ipath_devdata *dd) +{ +mutex_lock (&ipath_layer_mutex); + +if (dd->ipath_layer.l_arg && layer_remove_one) { +layer_remove_one (dd->ipath_layer.l_arg); + dd->ipath_layer.l_arg =NULL ; + } + +if (dd->verbs_layer.l_arg && verbs_remove_one) { +verbs_remove_one (dd->verbs_layer.l_arg); + dd->verbs_layer.l_arg =NULL ; + } + +mutex_unlock (&ipath_layer_mutex); +} + +int ipath_layer_register (void *(*l_add)(int ,struct ipath_devdata *), +void (*l_remove)(void *), +int (*l_intr)(void *,u32 ), +int (*l_rcv)(void *,void *,struct sk_buff *), +u16 l_rcv_opcode, +int (*l_rcv_lid)(void *,void *)) +{ +struct ipath_devdata *dd, *tmp; +unsigned long flags; + +mutex_lock (&ipath_layer_mutex); + + layer_add_one = l_add; + layer_remove_one = l_remove; + layer_intr = l_intr; + layer_rcv = l_rcv; + layer_rcv_lid = l_rcv_lid; + ipath_layer_rcv_opcode = l_rcv_opcode; + +spin_lock_irqsave (&ipath_devs_lock, flags); + +list_for_each_entry_safe (dd, tmp, &ipath_dev_list, ipath_list) { +if (!(dd->ipath_flags &IPATH_INITTED )) +continue ; + +if (dd->ipath_layer.l_arg) +continue ; + +if (!(*dd->ipath_statusp &IPATH_STATUS_SMA )) + *dd->ipath_statusp |=IPATH_STATUS_OIB_SMA ; + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + dd->ipath_layer.l_arg =l_add (dd->ipath_unit, dd); +spin_lock_irqsave (&ipath_devs_lock, flags); + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); +mutex_unlock (&ipath_layer_mutex); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_register); + +void ipath_layer_unregister (void ) +{ +struct ipath_devdata *dd, *tmp; +unsigned long flags; + +mutex_lock (&ipath_layer_mutex); +spin_lock_irqsave (&ipath_devs_lock, flags); + +list_for_each_entry_safe (dd, tmp, &ipath_dev_list, ipath_list) { +if (dd->ipath_layer.l_arg && layer_remove_one) { +spin_unlock_irqrestore (&ipath_devs_lock, flags); +layer_remove_one (dd->ipath_layer.l_arg); +spin_lock_irqsave (&ipath_devs_lock, flags); + dd->ipath_layer.l_arg =NULL ; + } + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + + layer_add_one =NULL ; + layer_remove_one =NULL ; + layer_intr =NULL ; + layer_rcv =NULL ; + layer_rcv_lid =NULL ; + +mutex_unlock (&ipath_layer_mutex); +} + +EXPORT_SYMBOL_GPL (ipath_layer_unregister); + +static void __ipath_verbs_timer (unsigned long arg) +{ +struct ipath_devdata *dd = (struct ipath_devdata *) arg; + +/* +* If port 0 receive packet interrupts are not available, or +* can be missed, poll the receive queue +*/ +if (dd->ipath_flags &IPATH_POLL_RX_INTR ) +ipath_kreceive (dd); + +/* Handle verbs layer timeouts. */ +if (dd->verbs_layer.l_arg && verbs_timer_cb) +verbs_timer_cb (dd->verbs_layer.l_arg); + +mod_timer (&dd->verbs_layer.l_timer, jiffies +1 ); +} + +/** +* ipath_verbs_register - verbs layer registration +* @l_piobufavail: callback for when PIO buffers become available +* @l_rcv: callback for receiving a packet +* @l_timer_cb: timer callback +* @ipath_devdata: device data structure is put here +*/ +int ipath_verbs_register (void *(*l_add)(int ,struct ipath_devdata *), +void (*l_remove)(void *arg), +int (*l_piobufavail) (void *arg), +void (*l_rcv) (void *arg,void *rhdr, +void *data,u32 tlen), +void (*l_timer_cb) (void *arg)) +{ +struct ipath_devdata *dd, *tmp; +unsigned long flags; + +mutex_lock (&ipath_layer_mutex); + + verbs_add_one = l_add; + verbs_remove_one = l_remove; + verbs_piobufavail = l_piobufavail; + verbs_rcv = l_rcv; + verbs_timer_cb = l_timer_cb; + +spin_lock_irqsave (&ipath_devs_lock, flags); + +list_for_each_entry_safe (dd, tmp, &ipath_dev_list, ipath_list) { +if (!(dd->ipath_flags &IPATH_INITTED )) +continue ; + +if (dd->verbs_layer.l_arg) +continue ; + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + dd->verbs_layer.l_arg =l_add (dd->ipath_unit, dd); +spin_lock_irqsave (&ipath_devs_lock, flags); + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); +mutex_unlock (&ipath_layer_mutex); + + ipath_verbs_registered =1 ; + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_verbs_register); + +void ipath_verbs_unregister (void ) +{ +struct ipath_devdata *dd, *tmp; +unsigned long flags; + +mutex_lock (&ipath_layer_mutex); +spin_lock_irqsave (&ipath_devs_lock, flags); + +list_for_each_entry_safe (dd, tmp, &ipath_dev_list, ipath_list) { + *dd->ipath_statusp &= ~IPATH_STATUS_OIB_SMA ; + +if (dd->verbs_layer.l_arg && verbs_remove_one) { +spin_unlock_irqrestore (&ipath_devs_lock, flags); +verbs_remove_one (dd->verbs_layer.l_arg); +spin_lock_irqsave (&ipath_devs_lock, flags); + dd->verbs_layer.l_arg =NULL ; + } + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + + verbs_add_one =NULL ; + verbs_remove_one =NULL ; + verbs_piobufavail =NULL ; + verbs_rcv =NULL ; + verbs_timer_cb =NULL ; + +mutex_unlock (&ipath_layer_mutex); +} + +EXPORT_SYMBOL_GPL (ipath_verbs_unregister); + +int ipath_layer_open (struct ipath_devdata *dd,u32 * pktmax) +{ +int ret; +u32 intval =0 ; + +mutex_lock (&ipath_layer_mutex); + +if (!dd->ipath_layer.l_arg) { + ret = -EINVAL ; + goto bail; + } + + ret =ipath_setrcvhdrsize (dd,NUM_OF_EXTRA_WORDS_IN_HEADER_QUEUE ); + +if (ret <0 ) + goto bail; + + *pktmax = dd->ipath_ibmaxlen; + +if (*dd->ipath_statusp &IPATH_STATUS_IB_READY ) + intval |=IPATH_LAYER_INT_IF_UP ; +if (ipath_stats.sps_lid[dd->ipath_unit]) + intval |=IPATH_LAYER_INT_LID ; +if (ipath_stats.sps_mlid[dd->ipath_unit]) + intval |=IPATH_LAYER_INT_BCAST ; +/* +* do this on open, in case low level is already up and +* just layered driver was reloaded, etc. +*/ +if (intval) +layer_intr (dd->ipath_layer.l_arg, intval); + + ret =0 ; +bail: +mutex_unlock (&ipath_layer_mutex); + +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_open); + +u16 ipath_layer_get_lid (struct ipath_devdata *dd) +{ +return dd->ipath_lid; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_lid); + +/** +* ipath_layer_get_mac - get the MAC address +* @dd: the infinipath device +* @mac: the MAC is put here +* +* This is the EUID-64 OUI octets (top 3), then +* skip the next 2 (which should both be zero or 0xff). +* The returned MAC is in network order +* mac points to at least 6 bytes of buffer +* We assume that by the time the LID is set, that the GUID is as valid +* as it's ever going to be, rather than adding yet another status bit. +*/ + +int ipath_layer_get_mac (struct ipath_devdata *dd,u8 * mac) +{ +u8 *guid; + + guid = (u8 *) &dd->ipath_guid; + + mac[0 ] = guid[0 ]; + mac[1 ] = guid[1 ]; + mac[2 ] = guid[2 ]; + mac[3 ] = guid[5 ]; + mac[4 ] = guid[6 ]; + mac[5 ] = guid[7 ]; +if ((guid[3 ] || guid[4 ]) && !(guid[3 ] ==0xff && guid[4 ] ==0xff )) +ipath_dbg ("Warning, guid bytes 3 and 4 not 0 or 0xffff: " +"%x %x\n" , guid[3 ], guid[4 ]); +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_mac); + +u16 ipath_layer_get_bcast (struct ipath_devdata *dd) +{ +return dd->ipath_mlid; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_bcast); + +u32 ipath_layer_get_cr_errpkey (struct ipath_devdata *dd) +{ +return ipath_read_creg32 (dd, dd->ipath_cregs->cr_errpkey); +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_cr_errpkey); + +static void update_sge (struct ipath_sge_state *ss,u32 length) +{ +struct ipath_sge *sge = &ss->sge; + + sge->vaddr += length; + sge->length -= length; + sge->sge_length -= length; +if (sge->sge_length ==0 ) { +if (--ss->num_sge) + *sge = *ss->sg_list++; + }else if (sge->length ==0 && sge->mr !=NULL ) { +if (++sge->n >=IPATH_SEGSZ ) { +if (++sge->m >= sge->mr->mapsz) +return ; + sge->n =0 ; + } + sge->vaddr = sge->mr->map[sge->m]->segs[sge->n].vaddr; + sge->length = sge->mr->map[sge->m]->segs[sge->n].length; + } +} + +#ifdef __LITTLE_ENDIAN +static inline u32 get_upper_bits (u32 data,u32 shift) +{ +return data >> shift; +} + +static inline u32 set_upper_bits (u32 data,u32 shift) +{ +return data << shift; +} + +static inline u32 clear_upper_bytes (u32 data,u32 n,u32 off) +{ + data <<= ((sizeof (u32) - n) *BITS_PER_BYTE ); + data >>= ((sizeof (u32) - n - off) *BITS_PER_BYTE ); +return data; +} +#else +static inline u32 get_upper_bits (u32 data,u32 shift) +{ +return data << shift; +} + +static inline u32 set_upper_bits (u32 data,u32 shift) +{ +return data >> shift; +} + +static inline u32 clear_upper_bytes (u32 data,u32 n,u32 off) +{ + data >>= ((sizeof (u32) - n) *BITS_PER_BYTE ); + data <<= ((sizeof (u32) - n - off) *BITS_PER_BYTE ); +return data; +} +#endif + +static void copy_io (u32 __iomem *piobuf,struct ipath_sge_state *ss, +u32 length) +{ +u32 extra =0 ; +u32 data =0 ; +u32 last; + +while (1 ) { +u32 len = ss->sge.length; +u32 off; + +BUG_ON (len ==0 ); +if (len > length) + len = length; +if (len > ss->sge.sge_length) + len = ss->sge.sge_length; +/* If the source address is not aligned, try to align it. */ + off = (unsigned long )ss->sge.vaddr & (sizeof (u32) -1 ); +if (off) { +u32 *addr = (u32 *)((unsigned long )ss->sge.vaddr & + ~(sizeof (u32) -1 )); +u32 v =get_upper_bits (*addr, off *BITS_PER_BYTE ); +u32 y; + + y =sizeof (u32) - off; +if (len > y) + len = y; +if (len + extra >=sizeof (u32)) { + data |=set_upper_bits (v, extra * +BITS_PER_BYTE ); + len =sizeof (u32) - extra; +if (len == length) { + last = data; +break ; + } +__raw_writel (data, piobuf); + piobuf++; + extra =0 ; + data =0 ; + }else { +/* Clear unused upper bytes */ + data |=clear_upper_bytes (v, len, extra); +if (len == length) { + last = data; +break ; + } + extra += len; + } + }else if (extra) { +/* Source address is aligned. */ +u32 *addr = (u32 *) ss->sge.vaddr; +int shift = extra *BITS_PER_BYTE ; +int ushift =32 - shift; +u32 l = len; + +while (l >=sizeof (u32)) { +u32 v = *addr; + + data |=set_upper_bits (v, shift); +__raw_writel (data, piobuf); + data =get_upper_bits (v, ushift); + piobuf++; + addr++; + l -=sizeof (u32); + } +/* +* We still have 'extra' number of bytes leftover. +*/ +if (l) { +u32 v = *addr; + +if (l + extra >=sizeof (u32)) { + data |=set_upper_bits (v, shift); + len -= l + extra -sizeof (u32); +if (len == length) { + last = data; +break ; + } +__raw_writel (data, piobuf); + piobuf++; + extra =0 ; + data =0 ; + }else { +/* Clear unused upper bytes */ + data |=clear_upper_bytes (v, l, + extra); +if (len == length) { + last = data; +break ; + } + extra += l; + } + }else if (len == length) { + last = data; +break ; + } + }else if (len == length) { +u32 w; + +/* +* Need to round up for the last dword in the +* packet. +*/ + w = (len +3 ) >>2 ; +__iowrite32_copy (piobuf, ss->sge.vaddr, w -1 ); + piobuf += w -1 ; + last = ((u32 *) ss->sge.vaddr)[w -1 ]; +break ; + }else { +u32 w = len >>2 ; + +__iowrite32_copy (piobuf, ss->sge.vaddr, w); + piobuf += w; + + extra = len & (sizeof (u32) -1 ); +if (extra) { +u32 v = ((u32 *) ss->sge.vaddr)[w]; + +/* Clear unused upper bytes */ + data =clear_upper_bytes (v, extra,0 ); + } + } +update_sge (ss, len); + length -= len; + } +/* must flush early everything before trigger word */ +ipath_flush_wc (); +__raw_writel (last, piobuf); +/* be sure trigger word is written */ +ipath_flush_wc (); +update_sge (ss, length); +} + +/** +* ipath_verbs_send - send a packet from the verbs layer +* @dd: the infinipath device +* @hdrwords: the number of works in the header +* @hdr: the packet header +* @len: the length of the packet in bytes +* @ss: the SGE to send +* +* This is like ipath_sma_send_pkt() in that we need to be able to send +* packets after the chip is initialized (MADs) but also like +* ipath_layer_send_hdr() since its used by the verbs layer. +*/ +int ipath_verbs_send (struct ipath_devdata *dd,u32 hdrwords, +u32 *hdr,u32 len,struct ipath_sge_state *ss) +{ +u32 __iomem *piobuf; +u32 plen; +int ret; + +/* +1 is for the qword padding of pbc */ + plen = hdrwords + ((len +3 ) >>2 ) +1 ; +if (unlikely ((plen <<2 ) > dd->ipath_ibmaxlen)) { +ipath_dbg ("packet len 0x%x too long, failing\n" , plen); + ret = -EINVAL ; + goto bail; + } + +/* Get a PIO buffer to use. */ + piobuf =ipath_getpiobuf (dd,NULL ); +if (unlikely (piobuf ==NULL )) { + ret = -EBUSY ; + goto bail; + } + +/* +* Write len to control qword, no flags. +* We have to flush after the PBC for correctness on some cpus +* or WC buffer can be written out of order. +*/ +writeq (plen, piobuf); +ipath_flush_wc (); + piobuf +=2 ; +if (len ==0 ) { +/* +* If there is just the header portion, must flush before +* writing last word of header for correctness, and after +* the last header word (trigger word). +*/ +__iowrite32_copy (piobuf, hdr, hdrwords -1 ); +ipath_flush_wc (); +__raw_writel (hdr[hdrwords -1 ], piobuf + hdrwords -1 ); +ipath_flush_wc (); + ret =0 ; + goto bail; + } + +__iowrite32_copy (piobuf, hdr, hdrwords); + piobuf += hdrwords; + +/* The common case is aligned and contained in one segment. */ +if (likely (ss->num_sge ==1 && len <= ss->sge.length && + !((unsigned long )ss->sge.vaddr & (sizeof (u32) -1 )))) { +u32 w; + +/* Need to round up for the last dword in the packet. */ + w = (len +3 ) >>2 ; +__iowrite32_copy (piobuf, ss->sge.vaddr, w -1 ); +/* must flush early everything before trigger word */ +ipath_flush_wc (); +__raw_writel (((u32 *) ss->sge.vaddr)[w -1 ], + piobuf + w -1 ); +/* be sure trigger word is written */ +ipath_flush_wc (); +update_sge (ss, len); + ret =0 ; + goto bail; + } +copy_io (piobuf, ss, len); + ret =0 ; + +bail: +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_verbs_send); + +int ipath_layer_snapshot_counters (struct ipath_devdata *dd,u64 *swords, +u64 *rwords,u64 *spkts,u64 *rpkts, +u64 *xmit_wait) +{ +int ret; + +if (!(dd->ipath_flags &IPATH_INITTED )) { +/* no hardware, freeze, etc. */ +ipath_dbg ("unit %u not usable\n" , dd->ipath_unit); + ret = -EINVAL ; + goto bail; + } + *swords =ipath_snap_cntr (dd, dd->ipath_cregs->cr_wordsendcnt); + *rwords =ipath_snap_cntr (dd, dd->ipath_cregs->cr_wordrcvcnt); + *spkts =ipath_snap_cntr (dd, dd->ipath_cregs->cr_pktsendcnt); + *rpkts =ipath_snap_cntr (dd, dd->ipath_cregs->cr_pktrcvcnt); + *xmit_wait =ipath_snap_cntr (dd, dd->ipath_cregs->cr_sendstallcnt); + + ret =0 ; + +bail: +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_snapshot_counters); + +/** +* ipath_layer_get_counters - get various chip counters +* @dd: the infinipath device +* @cntrs: counters are placed here +* +* Return the counters needed by recv_pma_get_portcounters(). +*/ +int ipath_layer_get_counters (struct ipath_devdata *dd, +struct ipath_layer_counters *cntrs) +{ +int ret; + +if (!(dd->ipath_flags &IPATH_INITTED )) { +/* no hardware, freeze, etc. */ +ipath_dbg ("unit %u not usable\n" , dd->ipath_unit); + ret = -EINVAL ; + goto bail; + } + cntrs->symbol_error_counter = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_ibsymbolerrcnt); + cntrs->link_error_recovery_counter = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_iblinkerrrecovcnt); + cntrs->link_downed_counter = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_iblinkdowncnt); + cntrs->port_rcv_errors = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_rxdroppktcnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_rcvovflcnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_portovflcnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_errrcvflowctrlcnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_err_rlencnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_invalidrlencnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_erricrccnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_errvcrccnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_errlpcrccnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_errlinkcnt) + +ipath_snap_cntr (dd, dd->ipath_cregs->cr_badformatcnt); + cntrs->port_rcv_remphys_errors = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_rcvebpcnt); + cntrs->port_xmit_discards = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_unsupvlcnt); + cntrs->port_xmit_data = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_wordsendcnt); + cntrs->port_rcv_data = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_wordrcvcnt); + cntrs->port_xmit_packets = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_pktsendcnt); + cntrs->port_rcv_packets = +ipath_snap_cntr (dd, dd->ipath_cregs->cr_pktrcvcnt); + + ret =0 ; + +bail: +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_counters); + +int ipath_layer_want_buffer (struct ipath_devdata *dd) +{ +set_bit (IPATH_S_PIOINTBUFAVAIL , &dd->ipath_sendctrl); +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, + dd->ipath_sendctrl); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_want_buffer); + +int ipath_layer_send_hdr (struct ipath_devdata *dd,struct ether_header *hdr) +{ +int ret =0 ; +u32 __iomem *piobuf; +u32 plen, *uhdr; +size_t count; +__be16 vlsllnh; + +if (!(dd->ipath_flags &IPATH_RCVHDRSZ_SET )) { +ipath_dbg ("send while not open\n" ); + ret = -EINVAL ; + }else +if ((dd->ipath_flags & (IPATH_LINKUNK |IPATH_LINKDOWN )) || + dd->ipath_lid ==0 ) { +/* +* lid check is for when sma hasn't yet configured +*/ + ret = -ENETDOWN ; +ipath_cdbg (VERBOSE ,"send while not ready, " +"mylid=%u, flags=0x%x\n" , + dd->ipath_lid, dd->ipath_flags); + } + + vlsllnh = *((__be16 *) hdr); +if (vlsllnh !=htons (IPS_LRH_BTH )) { +ipath_dbg ("Warning: lrh[0] wrong (%x, not %x); " +"not sending\n" ,be16_to_cpu (vlsllnh), +IPS_LRH_BTH ); + ret = -EINVAL ; + } +if (ret) + goto done; + +/* Get a PIO buffer to use. */ + piobuf =ipath_getpiobuf (dd,NULL ); +if (piobuf ==NULL ) { + ret = -EBUSY ; + goto done; + } + + plen = (sizeof (*hdr) >>2 );/* actual length */ +ipath_cdbg (EPKT ,"0x%x+1w pio %p\n" , plen, piobuf); + +writeq (plen+1 , piobuf);/* len (+1 for pad) to pbc, no flags */ +ipath_flush_wc (); + piobuf +=2 ; + uhdr = (u32 *)hdr; + count = plen-1 ;/* amount we can copy before trigger word */ +__iowrite32_copy (piobuf, uhdr, count); +ipath_flush_wc (); +__raw_writel (uhdr[count], piobuf + count); +ipath_flush_wc ();/* ensure it's sent, now */ + + ipath_stats.sps_ether_spkts++;/* ether packet sent */ + +done: +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_send_hdr); + +int ipath_layer_set_piointbufavail_int (struct ipath_devdata *dd) +{ +set_bit (IPATH_S_PIOINTBUFAVAIL , &dd->ipath_sendctrl); + +ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl, + dd->ipath_sendctrl); +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_piointbufavail_int); + +int ipath_layer_enable_timer (struct ipath_devdata *dd) +{ +/* +* HT-400 has a design flaw where the chip and kernel idea +* of the tail register don't always agree, and therefore we won't +* get an interrupt on the next packet received. +* If the board supports per packet receive interrupts, use it. +* Otherwise, the timer function periodically checks for packets +* to cover this case. +* Either way, the timer is needed for verbs layer related +* processing. +*/ +if (dd->ipath_flags &IPATH_GPIO_INTR ) { +ipath_write_kreg (dd, dd->ipath_kregs->kr_debugportselect, +0x2074076542310ULL ); +/* Enable GPIO bit 2 interrupt */ +ipath_write_kreg (dd, dd->ipath_kregs->kr_gpio_mask, + (u64) (1 <<2 )); + } + +init_timer (&dd->verbs_layer.l_timer); + dd->verbs_layer.l_timer.function = __ipath_verbs_timer; + dd->verbs_layer.l_timer.data = (unsigned long )dd; + dd->verbs_layer.l_timer.expires = jiffies +1 ; +add_timer (&dd->verbs_layer.l_timer); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_enable_timer); + +int ipath_layer_disable_timer (struct ipath_devdata *dd) +{ +/* Disable GPIO bit 2 interrupt */ +if (dd->ipath_flags &IPATH_GPIO_INTR ) +ipath_write_kreg (dd, dd->ipath_kregs->kr_gpio_mask,0 ); + +del_timer_sync (&dd->verbs_layer.l_timer); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_disable_timer); + +/** +* ipath_layer_set_verbs_flags - set the verbs layer flags +* @dd: the infinipath device +* @flags: the flags to set +*/ +int ipath_layer_set_verbs_flags (struct ipath_devdata *dd,unsigned flags) +{ +struct ipath_devdata *ss; +unsigned long lflags; + +spin_lock_irqsave (&ipath_devs_lock, lflags); + +list_for_each_entry (ss, &ipath_dev_list, ipath_list) { +if (!(ss->ipath_flags &IPATH_INITTED )) +continue ; +if ((flags &IPATH_VERBS_KERNEL_SMA ) && + !(*ss->ipath_statusp &IPATH_STATUS_SMA )) + *ss->ipath_statusp |=IPATH_STATUS_OIB_SMA ; +else + *ss->ipath_statusp &= ~IPATH_STATUS_OIB_SMA ; + } + +spin_unlock_irqrestore (&ipath_devs_lock, lflags); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_verbs_flags); + +/** +* ipath_layer_get_npkeys - return the size of the PKEY table for port 0 +* @dd: the infinipath device +*/ +unsigned ipath_layer_get_npkeys (struct ipath_devdata *dd) +{ +return ARRAY_SIZE (dd->ipath_pd[0 ]->port_pkeys); +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_npkeys); + +/** +* ipath_layer_get_pkey - return the indexed PKEY from the port 0 PKEY table +* @dd: the infinipath device +* @index: the PKEY index +*/ +unsigned ipath_layer_get_pkey (struct ipath_devdata *dd,unsigned index) +{ +unsigned ret; + +if (index >=ARRAY_SIZE (dd->ipath_pd[0 ]->port_pkeys)) + ret =0 ; +else + ret = dd->ipath_pd[0 ]->port_pkeys[index]; + +return ret; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_pkey); + +/** +* ipath_layer_get_pkeys - return the PKEY table for port 0 +* @dd: the infinipath device +* @pkeys: the pkey table is placed here +*/ +int ipath_layer_get_pkeys (struct ipath_devdata *dd,u16 * pkeys) +{ +struct ipath_portdata *pd = dd->ipath_pd[0 ]; + +memcpy (pkeys, pd->port_pkeys,sizeof (pd->port_pkeys)); + +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_pkeys); + +/** +* rm_pkey - decrecment the reference count for the given PKEY +* @dd: the infinipath device +* @key: the PKEY index +* +* Return true if this was the last reference and the hardware table entry +* needs to be changed. +*/ +static int rm_pkey (struct ipath_devdata *dd,u16 key) +{ +int i; +int ret; + +for (i =0 ; i <ARRAY_SIZE (dd->ipath_pkeys); i++) { +if (dd->ipath_pkeys[i] != key) +continue ; +if (atomic_dec_and_test (&dd->ipath_pkeyrefs[i])) { + dd->ipath_pkeys[i] =0 ; + ret =1 ; + goto bail; + } +break ; + } + + ret =0 ; + +bail: +return ret; +} + +/** +* add_pkey - add the given PKEY to the hardware table +* @dd: the infinipath device +* @key: the PKEY +* +* Return an error code if unable to add the entry, zero if no change, +* or 1 if the hardware PKEY register needs to be updated. +*/ +static int add_pkey (struct ipath_devdata *dd,u16 key) +{ +int i; +u16 lkey = key &0x7FFF ; +int any =0 ; +int ret; + +if (lkey ==0x7FFF ) { + ret =0 ; + goto bail; + } + +/* Look for an empty slot or a matching PKEY. */ +for (i =0 ; i <ARRAY_SIZE (dd->ipath_pkeys); i++) { +if (!dd->ipath_pkeys[i]) { + any++; +continue ; + } +/* If it matches exactly, try to increment the ref count */ +if (dd->ipath_pkeys[i] == key) { +if (atomic_inc_return (&dd->ipath_pkeyrefs[i]) >1 ) { + ret =0 ; + goto bail; + } +/* Lost the race. Look for an empty slot below. */ +atomic_dec (&dd->ipath_pkeyrefs[i]); + any++; + } +/* +* It makes no sense to have both the limited and unlimited +* PKEY set at the same time since the unlimited one will +* disable the limited one. +*/ +if ((dd->ipath_pkeys[i] &0x7FFF ) == lkey) { + ret = -EEXIST ; + goto bail; + } + } +if (!any) { + ret = -EBUSY ; + goto bail; + } +for (i =0 ; i <ARRAY_SIZE (dd->ipath_pkeys); i++) { +if (!dd->ipath_pkeys[i] && +atomic_inc_return (&dd->ipath_pkeyrefs[i]) ==1 ) { +/* for ipathstats, etc. */ + ipath_stats.sps_pkeys[i] = lkey; + dd->ipath_pkeys[i] = key; + ret =1 ; + goto bail; + } + } + ret = -EBUSY ; + +bail: +return ret; +} + +/** +* ipath_layer_set_pkeys - set the PKEY table for port 0 +* @dd: the infinipath device +* @pkeys: the PKEY table +*/ +int ipath_layer_set_pkeys (struct ipath_devdata *dd,u16 * pkeys) +{ +struct ipath_portdata *pd; +int i; +int changed =0 ; + + pd = dd->ipath_pd[0 ]; + +for (i =0 ; i <ARRAY_SIZE (pd->port_pkeys); i++) { +u16 key = pkeys[i]; +u16 okey = pd->port_pkeys[i]; + +if (key == okey) +continue ; +/* +* The value of this PKEY table entry is changing. +* Remove the old entry in the hardware's array of PKEYs. +*/ +if (okey &0x7FFF ) + changed |=rm_pkey (dd, okey); +if (key &0x7FFF ) { +int ret =add_pkey (dd, key); + +if (ret <0 ) + key =0 ; +else + changed |= ret; + } + pd->port_pkeys[i] = key; + } +if (changed) { +u64 pkey; + + pkey = (u64 ) dd->ipath_pkeys[0 ] | + ((u64 ) dd->ipath_pkeys[1 ] <<16 ) | + ((u64 ) dd->ipath_pkeys[2 ] <<32 ) | + ((u64 ) dd->ipath_pkeys[3 ] <<48 ); +ipath_cdbg (VERBOSE ,"p0 new pkey reg %llx\n" , + (unsigned long long ) pkey); +ipath_write_kreg (dd, dd->ipath_kregs->kr_partitionkey, + pkey); + } +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_pkeys); + +/** +* ipath_layer_get_linkdowndefaultstate - get the default linkdown state +* @dd: the infinipath device +* +* Returns zero if the default is POLL, 1 if the default is SLEEP. +*/ +int ipath_layer_get_linkdowndefaultstate (struct ipath_devdata *dd) +{ +return !!(dd->ipath_ibcctrl &INFINIPATH_IBCC_LINKDOWNDEFAULTSTATE ); +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_linkdowndefaultstate); + +/** +* ipath_layer_set_linkdowndefaultstate - set the default linkdown state +* @dd: the infinipath device +* @sleep: the new state +* +* Note that this will only take effect when the link state changes. +*/ +int ipath_layer_set_linkdowndefaultstate (struct ipath_devdata *dd, +int sleep) +{ +if (sleep) + dd->ipath_ibcctrl |=INFINIPATH_IBCC_LINKDOWNDEFAULTSTATE ; +else + dd->ipath_ibcctrl &= ~INFINIPATH_IBCC_LINKDOWNDEFAULTSTATE ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_ibcctrl, + dd->ipath_ibcctrl); +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_linkdowndefaultstate); + +int ipath_layer_get_phyerrthreshold (struct ipath_devdata *dd) +{ +return (dd->ipath_ibcctrl >> +INFINIPATH_IBCC_PHYERRTHRESHOLD_SHIFT ) & +INFINIPATH_IBCC_PHYERRTHRESHOLD_MASK ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_phyerrthreshold); + +/** +* ipath_layer_set_phyerrthreshold - set the physical error threshold +* @dd: the infinipath device +* @n: the new threshold +* +* Note that this will only take effect when the link state changes. +*/ +int ipath_layer_set_phyerrthreshold (struct ipath_devdata *dd,unsigned n) +{ +unsigned v; + + v = (dd->ipath_ibcctrl >>INFINIPATH_IBCC_PHYERRTHRESHOLD_SHIFT ) & +INFINIPATH_IBCC_PHYERRTHRESHOLD_MASK ; +if (v != n) { + dd->ipath_ibcctrl &= + ~(INFINIPATH_IBCC_PHYERRTHRESHOLD_MASK << +INFINIPATH_IBCC_PHYERRTHRESHOLD_SHIFT ); + dd->ipath_ibcctrl |= + (u64 ) n <<INFINIPATH_IBCC_PHYERRTHRESHOLD_SHIFT ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_ibcctrl, + dd->ipath_ibcctrl); + } +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_phyerrthreshold); + +int ipath_layer_get_overrunthreshold (struct ipath_devdata *dd) +{ +return (dd->ipath_ibcctrl >> +INFINIPATH_IBCC_OVERRUNTHRESHOLD_SHIFT ) & +INFINIPATH_IBCC_OVERRUNTHRESHOLD_MASK ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_get_overrunthreshold); + +/** +* ipath_layer_set_overrunthreshold - set the overrun threshold +* @dd: the infinipath device +* @n: the new threshold +* +* Note that this will only take effect when the link state changes. +*/ +int ipath_layer_set_overrunthreshold (struct ipath_devdata *dd,unsigned n) +{ +unsigned v; + + v = (dd->ipath_ibcctrl >>INFINIPATH_IBCC_OVERRUNTHRESHOLD_SHIFT ) & +INFINIPATH_IBCC_OVERRUNTHRESHOLD_MASK ; +if (v != n) { + dd->ipath_ibcctrl &= + ~(INFINIPATH_IBCC_OVERRUNTHRESHOLD_MASK << +INFINIPATH_IBCC_OVERRUNTHRESHOLD_SHIFT ); + dd->ipath_ibcctrl |= + (u64 ) n <<INFINIPATH_IBCC_OVERRUNTHRESHOLD_SHIFT ; +ipath_write_kreg (dd, dd->ipath_kregs->kr_ibcctrl, + dd->ipath_ibcctrl); + } +return 0 ; +} + +EXPORT_SYMBOL_GPL (ipath_layer_set_overrunthreshold); + +int ipath_layer_get_boardname (struct ipath_devdata *dd,char *name, +size_t namelen) +{ +return dd->ipath_f_get_boardname (dd, name, namelen); +} +EXPORT_SYMBOL_GPL (ipath_layer_get_boardname); + +u32 ipath_layer_get_rcvhdrentsize (struct ipath_devdata *dd) +{ +return dd->ipath_rcvhdrentsize; +} +EXPORT_SYMBOL_GPL (ipath_layer_get_rcvhdrentsize);
drivers/infiniband/hw/ipath/ipath_layer.h new file +181 -0
181 lines not on this page · raw message
PATCH 1/1 ipath - sysfs and ipathfs support for core driver
In reply to Bryan O'SullivanThe ipathfs filesystem contains files that are not appropriate for sysfs, because they contain binary data. The hierarchy is simple; the top-level directory contains driver-wide attribute files, while numbered subdirectories contain per-device attribute files.
Our userspace code currently expects this filesystem to be mounted on /ipathfs, but a final location has not yet been chosen.
drivers/infiniband/hw/ipath/ipath_fs.c new file +605 -0
@@ -0,0 +1,605 @@ +/* +* Copyright (c) 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include <linux/version.h> +#include <linux/config.h> +#include <linux/module.h> +#include <linux/fs.h> +#include <linux/mount.h> +#include <linux/pagemap.h> +#include <linux/init.h> +#include <linux/namei.h> +#include <linux/pci.h> + +#include "ipath_kernel.h" + +#define IPATHFS_MAGIC 0x726a77 + +static struct super_block *ipath_super; + +static int ipathfs_mknod (struct inode *dir,struct dentry *dentry, +int mode,struct file_operations *fops, +void *data) +{ +int error; +struct inode *inode =new_inode (dir->i_sb); + +if (!inode) { + error = -EPERM ; + goto bail; + } + + inode->i_mode = mode; + inode->i_uid =0 ; + inode->i_gid =0 ; + inode->i_blksize =PAGE_CACHE_SIZE ; + inode->i_blocks =0 ; + inode->i_atime = inode->i_mtime = inode->i_ctime =CURRENT_TIME ; + inode->u.generic_ip = data; +if ((mode &S_IFMT ) ==S_IFDIR ) { + inode->i_op = &simple_dir_inode_operations; + inode->i_nlink++; + dir->i_nlink++; + } + + inode->i_fop = fops; + +d_instantiate (dentry, inode); + error =0 ; + +bail: +return error; +} + +static int create_file (const char *name,mode_t mode, +struct dentry *parent,struct dentry **dentry, +struct file_operations *fops,void *data) +{ +int error; + + *dentry =NULL ; +mutex_lock (&parent->d_inode->i_mutex); + *dentry =lookup_one_len (name, parent,strlen (name)); +if (!IS_ERR (dentry)) + error =ipathfs_mknod (parent->d_inode, *dentry, + mode, fops, data); +else + error =PTR_ERR (dentry); +mutex_unlock (&parent->d_inode->i_mutex); + +return error; +} + +static ssize_t atomic_stats_read (struct file *file,char __user *buf, +size_t count,loff_t *ppos) +{ +return simple_read_from_buffer (buf, count, ppos, &ipath_stats, +sizeof ipath_stats); +} + +static struct file_operations atomic_stats_ops = { + .read = atomic_stats_read, +}; + +#define NUM_COUNTERS sizeof(struct infinipath_counters) / sizeof(u64) + +static ssize_t atomic_counters_read (struct file *file,char __user *buf, +size_t count,loff_t *ppos) +{ +u64 counters[NUM_COUNTERS ]; +u16 i; +struct ipath_devdata *dd; + + dd = file->f_dentry->d_inode->u.generic_ip; + +for (i =0 ; i <NUM_COUNTERS ; i++) + counters[i] =ipath_snap_cntr (dd, i); + +return simple_read_from_buffer (buf, count, ppos, counters, +sizeof counters); +} + +static struct file_operations atomic_counters_ops = { + .read = atomic_counters_read, +}; + +static ssize_t atomic_node_info_read (struct file *file,char __user *buf, +size_t count,loff_t *ppos) +{ +u32 nodeinfo[10 ]; +struct ipath_devdata *dd; +u64 guid; + + dd = file->f_dentry->d_inode->u.generic_ip; + + guid =be64_to_cpu (dd->ipath_guid); + + nodeinfo[0 ] =/* BaseVersion is SMA */ +/* ClassVersion is SMA */ + (1 <<8 )/* NodeType */ + | (1 <<0 );/* NumPorts */ + nodeinfo[1 ] = (u32) (guid >>32 ); + nodeinfo[2 ] = (u32) (guid &0xffffffff ); +/* PortGUID == SystemImageGUID for us */ + nodeinfo[3 ] = nodeinfo[1 ]; +/* PortGUID == SystemImageGUID for us */ + nodeinfo[4 ] = nodeinfo[2 ]; +/* PortGUID == NodeGUID for us */ + nodeinfo[5 ] = nodeinfo[3 ]; +/* PortGUID == NodeGUID for us */ + nodeinfo[6 ] = nodeinfo[4 ]; + nodeinfo[7 ] = (4 <<16 )/* we support 4 pkeys */ + | (dd->ipath_deviceid <<0 ); +/* our chip version as 16 bits major, 16 bits minor */ + nodeinfo[8 ] = dd->ipath_minrev | (dd->ipath_majrev <<16 ); + nodeinfo[9 ] = (dd->ipath_unit <<24 ) | (dd->ipath_vendorid <<0 ); + +return simple_read_from_buffer (buf, count, ppos, nodeinfo, +sizeof nodeinfo); +} + +static struct file_operations atomic_node_info_ops = { + .read = atomic_node_info_read, +}; + +static ssize_t atomic_port_info_read (struct file *file,char __user *buf, +size_t count,loff_t *ppos) +{ +u32 portinfo[13 ]; +u32 tmp, tmp2; +struct ipath_devdata *dd; + + dd = file->f_dentry->d_inode->u.generic_ip; + +/* so we only initialize non-zero fields. */ +memset (portinfo,0 ,sizeof portinfo); + +/* +* Notimpl yet M_Key (64) +* Notimpl yet GID (64) +*/ + + portinfo[4 ] = (dd->ipath_lid <<16 ); + +/* +* Notimpl yet SMLID (should we store this in the driver, in case +* SMA dies?) CapabilityMask is 0, we don't support any of these +* DiagCode is 0; we don't store any diag info for now Notimpl yet +* M_KeyLeasePeriod (we don't support M_Key) +*/ + +/* LocalPortNum is whichever port number they ask for */ + portinfo[7 ] = (dd->ipath_unit <<24 ) +/* LinkWidthEnabled */ + | (2 <<16 ) +/* LinkWidthSupported (really 2, but not IB valid) */ + | (3 <<8 ) +/* LinkWidthActive */ + | (2 <<0 ); + tmp = dd->ipath_lastibcstat &IPATH_IBSTATE_MASK ; + tmp2 =5 ; +if (tmp ==IPATH_IBSTATE_INIT ) + tmp =2 ; +else if (tmp ==IPATH_IBSTATE_ARM ) + tmp =3 ; +else if (tmp ==IPATH_IBSTATE_ACTIVE ) + tmp =4 ; +else { + tmp =0 ;/* down */ + tmp2 = tmp &0xf ; + } + + portinfo[8 ] = (1 <<28 )/* LinkSpeedSupported */ + | (tmp <<24 )/* PortState */ + | (tmp2 <<20 )/* PortPhysicalState */ + | (2 <<16 ) + +/* LinkDownDefaultState */ +/* M_KeyProtectBits == 0 */ +/* NotImpl yet LMC == 0 (we can support all values) */ + | (1 <<4 )/* LinkSpeedActive */ + | (1 <<0 );/* LinkSpeedEnabled */ +switch (dd->ipath_ibmtu) { +case 4096 : + tmp =5 ; +break ; +case 2048 : + tmp =4 ; +break ; +case 1024 : + tmp =3 ; +break ; +case 512 : + tmp =2 ; +break ; +case 256 : + tmp =1 ; +break ; +default :/* oops, something is wrong */ +ipath_dbg ("Problem, ipath_ibmtu 0x%x not a valid IB MTU, " +"treat as 2048\n" , dd->ipath_ibmtu); + tmp =4 ; +break ; + } + portinfo[9 ] = (tmp <<28 ) +/* NeighborMTU */ +/* Notimpl MasterSMSL */ + | (1 <<20 ) + +/* VLCap */ +/* Notimpl InitType (actually, an SMA decision) */ +/* VLHighLimit is 0 (only one VL) */ + ;/* VLArbitrationHighCap is 0 (only one VL) */ + portinfo[10 ] =/* VLArbitrationLowCap is 0 (only one VL) */ +/* InitTypeReply is SMA decision */ + (5 <<16 )/* MTUCap 4096 */ + | (7 <<13 )/* VLStallCount */ + | (0x1f <<8 )/* HOQLife */ + | (1 <<4 ) + +/* OperationalVLs 0 */ +/* PartitionEnforcementInbound */ +/* PartitionEnforcementOutbound not enforced */ +/* FilterRawinbound not enforced */ + ;/* FilterRawOutbound not enforced */ +/* M_KeyViolations are not counted by hardware, SMA can count */ + tmp =ipath_read_creg32 (dd, dd->ipath_cregs->cr_errpkey); +/* P_KeyViolations are counted by hardware. */ + portinfo[11 ] = ((tmp &0xffff ) <<0 ); + portinfo[12 ] = +/* Q_KeyViolations are not counted by hardware */ + (1 <<8 ) + +/* GUIDCap */ +/* SubnetTimeOut handled by SMA */ +/* RespTimeValue handled by SMA */ + ; +/* LocalPhyErrors are programmed to max */ + portinfo[12 ] |= (0xf <<20 ) + | (0xf <<16 )/* OverRunErrors are programmed to max */ + ; + +return simple_read_from_buffer (buf, count, ppos, portinfo, +sizeof portinfo); +} + +static struct file_operations atomic_port_info_ops = { + .read = atomic_port_info_read, +}; + +static ssize_t flash_read (struct file *file,char __user *buf, +size_t count,loff_t *ppos) +{ +struct ipath_devdata *dd; +ssize_t ret; +loff_t pos; +char *tmp; + + pos = *ppos; + +if ( pos <0 ) { + ret = -EINVAL ; + goto bail; + } + +if (pos >=sizeof (struct ipath_flash )) { + ret =0 ; + goto bail; + } + +if (count >sizeof (struct ipath_flash ) - pos) + count =sizeof (struct ipath_flash ) - pos; + + tmp =kmalloc (count,GFP_KERNEL ); +if (!tmp) { + ret = -ENOMEM ; + goto bail; + } + + dd = file->f_dentry->d_inode->u.generic_ip; +if (ipath_eeprom_read (dd, pos, tmp, count)) { +ipath_dev_err (dd,"failed to read from flash\n" ); + ret = -ENXIO ; + goto bail_tmp; + } + +if (copy_to_user (buf, tmp, count)) { + ret = -EFAULT ; + goto bail_tmp; + } + + *ppos = pos + count; + ret = count; + +bail_tmp: +kfree (tmp); + +bail: +return ret; +} + +static ssize_t flash_write (struct file *file,const char __user *buf, +size_t count,loff_t *ppos) +{ +struct ipath_devdata *dd; +ssize_t ret; +loff_t pos; +char *tmp; + + pos = *ppos; + +if ( pos <0 ) { + ret = -EINVAL ; + goto bail; + } + +if (pos >=sizeof (struct ipath_flash )) { + ret =0 ; + goto bail; + } + +if (count >sizeof (struct ipath_flash ) - pos) + count =sizeof (struct ipath_flash ) - pos; + + tmp =kmalloc (count,GFP_KERNEL ); +if (!tmp) { + ret = -ENOMEM ; + goto bail; + } + +if (copy_from_user (tmp, buf, count)) { + ret = -EFAULT ; + goto bail_tmp; + } + + dd = file->f_dentry->d_inode->u.generic_ip; +if (ipath_eeprom_write (dd, pos, tmp, count)) { + ret = -ENXIO ; +ipath_dev_err (dd,"failed to write to flash\n" ); + goto bail_tmp; + } + + *ppos = pos + count; + ret = count; + +bail_tmp: +kfree (tmp); + +bail: +return ret; +} + +static struct file_operations flash_ops = { + .read = flash_read, + .write = flash_write, +}; + +static int create_device_files (struct super_block *sb, +struct ipath_devdata *dd) +{ +struct dentry *dir, *tmp; +char unit[10 ]; +int ret; + +snprintf (unit,sizeof unit,"%02d" , dd->ipath_unit); + ret =create_file (unit,S_IFDIR |S_IRUGO |S_IXUGO , sb->s_root, &dir, + (struct file_operations *) &simple_dir_operations, + dd); +if (ret) { +printk (KERN_ERR "create_file(%s) failed: %d\n" , unit, ret); + goto bail; + } + + ret =create_file ("atomic_counters" ,S_IFREG |S_IRUGO , dir, &tmp, + &atomic_counters_ops, dd); +if (ret) { +printk (KERN_ERR "create_file(%s/atomic_counters) " +"failed: %d\n" , unit, ret); + goto bail; + } + + ret =create_file ("node_info" ,S_IFREG |S_IRUGO , dir, &tmp, + &atomic_node_info_ops, dd); +if (ret) { +printk (KERN_ERR "create_file(%s/node_info) " +"failed: %d\n" , unit, ret); + goto bail; + } + + ret =create_file ("port_info" ,S_IFREG |S_IRUGO , dir, &tmp, + &atomic_port_info_ops, dd); +if (ret) { +printk (KERN_ERR "create_file(%s/port_info) " +"failed: %d\n" , unit, ret); + goto bail; + } + + ret =create_file ("flash" ,S_IFREG |S_IWUSR |S_IRUGO , dir, &tmp, + &flash_ops, dd); +if (ret) { +printk (KERN_ERR "create_file(%s/flash) " +"failed: %d\n" , unit, ret); + goto bail; + } + +bail: +return ret; +} + +static void remove_file (struct dentry *parent,char *name) +{ +struct dentry *tmp; + + tmp =lookup_one_len (name, parent,strlen (name)); + +spin_lock (&dcache_lock); +spin_lock (&tmp->d_lock); +if (!(d_unhashed (tmp) && tmp->d_inode)) { +dget_locked (tmp); +__d_drop (tmp); +spin_unlock (&tmp->d_lock); +spin_unlock (&dcache_lock); +simple_unlink (parent->d_inode, tmp); + }else { +spin_unlock (&tmp->d_lock); +spin_unlock (&dcache_lock); + } +} + +static int remove_device_files (struct super_block *sb, +struct ipath_devdata *dd) +{ +struct dentry *dir, *root; +char unit[10 ]; +int ret; + + root =dget (sb->s_root); +mutex_lock (&root->d_inode->i_mutex); +snprintf (unit,sizeof unit,"%02d" , dd->ipath_unit); + dir =lookup_one_len (unit, root,strlen (unit)); + +if (IS_ERR (dir)) { + ret =PTR_ERR (dir); +printk (KERN_ERR "Lookup of %s failed\n" , unit); + goto bail; + } + +remove_file (dir,"flash" ); +remove_file (dir,"port_info" ); +remove_file (dir,"node_info" ); +remove_file (dir,"atomic_counters" ); +d_delete (dir); + ret =simple_rmdir (root->d_inode, dir); + +bail: +mutex_unlock (&root->d_inode->i_mutex); +dput (root); +return ret; +} + +static int ipathfs_fill_super (struct super_block *sb,void *data, +int silent) +{ +struct ipath_devdata *dd, *tmp; +unsigned long flags; +int ret; + +static struct tree_descr files[] = { + [1 ] = {"atomic_stats" , &atomic_stats_ops,S_IRUGO }, + {"" }, + }; + + ret =simple_fill_super (sb,IPATHFS_MAGIC , files); +if (ret) { +printk (KERN_ERR "simple_fill_super failed: %d\n" , ret); + goto bail; + } + +spin_lock_irqsave (&ipath_devs_lock, flags); + +list_for_each_entry_safe (dd, tmp, &ipath_dev_list, ipath_list) { +spin_unlock_irqrestore (&ipath_devs_lock, flags); + ret =create_device_files (sb, dd); +if (ret) { +deactivate_super (sb); + goto bail; + } +spin_lock_irqsave (&ipath_devs_lock, flags); + } + +spin_unlock_irqrestore (&ipath_devs_lock, flags); + +bail: +return ret; +} + +static struct super_block *ipathfs_get_sb (struct file_system_type *fs_type, +int flags,const char *dev_name, +void *data) +{ + ipath_super =get_sb_single (fs_type, flags, data, + ipathfs_fill_super); +return ipath_super; +} + +static void ipathfs_kill_super (struct super_block *s) +{ +kill_litter_super (s); + ipath_super =NULL ; +} + +int ipathfs_add_device (struct ipath_devdata *dd) +{ +int ret; + +if (ipath_super ==NULL ) { + ret =0 ; + goto bail; + } + + ret =create_device_files (ipath_super, dd); + +bail: +return ret; +} + +int ipathfs_remove_device (struct ipath_devdata *dd) +{ +int ret; + +if (ipath_super ==NULL ) { + ret =0 ; + goto bail; + } + + ret =remove_device_files (ipath_super, dd); + +bail: +return ret; +} + +static struct file_system_type ipathfs_fs_type = { + .owner =THIS_MODULE , + .name ="ipathfs" , + .get_sb = ipathfs_get_sb, + .kill_sb = ipathfs_kill_super, +}; + +int __init ipath_init_ipathfs (void ) +{ +return register_filesystem (&ipathfs_fs_type); +} + +void __exit ipath_exit_ipathfs(void) +{ +unregister_filesystem (&ipathfs_fs_type); +}
drivers/infiniband/hw/ipath/ipath_sysfs.c new file +778 -0
778 lines not on this page · raw message
PATCH 1/1 ipath - support for userspace apps using core driver
In reply to Bryan O'SullivanThese files introduce a char device that userspace apps use to gain direct memory-mapped access to the InfiniPath hardware, and routines for pinning and unpinning user memory in cases where the hardware needs to DMA into the user address space.
drivers/infiniband/hw/ipath/ipath_file_ops.c new file +1910 -0
@@ -0,0 +1,1910 @@ +/* +* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include <linux/pci.h> +#include <linux/poll.h> +#include <linux/cdev.h> +#include <linux/swap.h> +#include <linux/vmalloc.h> +#include <asm/pgtable.h> + +#include "ipath_kernel.h" +#include "ips_common.h" +#include "ipath_layer.h" + +static int ipath_open (struct inode *,struct file *); +static int ipath_close (struct inode *,struct file *); +static ssize_t ipath_write (struct file *,const char __user *,size_t , +loff_t *); +static unsigned int ipath_poll (struct file *,struct poll_table_struct *); +static int ipath_mmap (struct file *,struct vm_area_struct *); + +static struct file_operations ipath_file_ops = { + .owner =THIS_MODULE , + .write = ipath_write, + .open = ipath_open, + .release = ipath_close, + .poll = ipath_poll, + .mmap = ipath_mmap +}; + +static int ipath_get_base_info (struct ipath_portdata *pd, +void __user *ubase,size_t ubase_size) +{ +int ret =0 ; +struct ipath_base_info *kinfo =NULL ; +struct ipath_devdata *dd = pd->port_dd; + +if (ubase_size <sizeof (*kinfo)) { +ipath_cdbg (PROC , +"Base size %lu, need %lu (version mismatch?)\n" , + (unsigned long ) ubase_size, + (unsigned long )sizeof (*kinfo)); + ret = -EINVAL ; + goto bail; + } + + kinfo =kzalloc (sizeof (*kinfo),GFP_KERNEL ); +if (kinfo ==NULL ) { + ret = -ENOMEM ; + goto bail; + } + + ret = dd->ipath_f_get_base_info (pd, kinfo); +if (ret <0 ) + goto bail; + + kinfo->spi_rcvhdr_cnt = dd->ipath_rcvhdrcnt; + kinfo->spi_rcvhdrent_size = dd->ipath_rcvhdrentsize; + kinfo->spi_tidegrcnt = dd->ipath_rcvegrcnt; + kinfo->spi_rcv_egrbufsize = dd->ipath_rcvegrbufsize; +/* +* have to mmap whole thing +*/ + kinfo->spi_rcv_egrbuftotlen = + pd->port_rcvegrbuf_chunks * pd->port_rcvegrbuf_size; + kinfo->spi_rcv_egrperchunk = pd->port_rcvegrbufs_perchunk; + kinfo->spi_rcv_egrchunksize = kinfo->spi_rcv_egrbuftotlen / + pd->port_rcvegrbuf_chunks; + kinfo->spi_tidcnt = dd->ipath_rcvtidcnt; +/* +* for this use, may be ipath_cfgports summed over all chips that +* are are configured and present +*/ + kinfo->spi_nports = dd->ipath_cfgports; +/* unit (chip/board) our port is on */ + kinfo->spi_unit = dd->ipath_unit; +/* for now, only a single page */ + kinfo->spi_tid_maxsize =PAGE_SIZE ; + +/* +* Doing this per port, and based on the skip value, etc. This has +* to be the actual buffer size, since the protocol code treats it +* as an array. +* +* These have to be set to user addresses in the user code via mmap. +* These values are used on return to user code for the mmap target +* addresses only. For 32 bit, same 44 bit address problem, so use +* the physical address, not virtual. Before 2.6.11, using the +* page_address() macro worked, but in 2.6.11, even that returns the +* full 64 bit address (upper bits all 1's). So far, using the +* physical addresses (or chip offsets, for chip mapping) works, but +* no doubt some future kernel release will chang that, and we'll be +* on to yet another method of dealing with this +*/ + kinfo->spi_rcvhdr_base = (u64 ) pd->port_rcvhdrq_phys; + kinfo->spi_rcv_egrbufs = (u64 ) pd->port_rcvegr_phys; + kinfo->spi_pioavailaddr = (u64 ) dd->ipath_pioavailregs_phys; + kinfo->spi_status = (u64 ) kinfo->spi_pioavailaddr + + (void *) dd->ipath_statusp - + (void *) dd->ipath_pioavailregs_dma; + kinfo->spi_piobufbase = (u64 ) pd->port_piobufs; + kinfo->__spi_uregbase = + dd->ipath_uregbase + dd->ipath_palign * pd->port_port; + + kinfo->spi_pioindex = dd->ipath_pbufsport * (pd->port_port -1 ); + kinfo->spi_piocnt = dd->ipath_pbufsport; + kinfo->spi_pioalign = dd->ipath_palign; + + kinfo->spi_qpair =IPATH_KD_QP ; + kinfo->spi_piosize = dd->ipath_ibmaxlen; + kinfo->spi_mtu = dd->ipath_ibmaxlen;/* maxlen, not ibmtu */ + kinfo->spi_port = pd->port_port; + kinfo->spi_sw_version =IPATH_USER_SWVERSION ; + kinfo->spi_hw_version = dd->ipath_revision; + +if (copy_to_user (ubase, kinfo,sizeof (*kinfo))) + ret = -EFAULT ; + +bail: +kfree (kinfo); +return ret; +} + +/** +* ipath_tid_update - update a port TID +* @pd: the port +* @ti: the TID information +* +* The new implementation as of Oct 2004 is that the driver assigns +* the tid and returns it to the caller. To make it easier to +* catch bugs, and to reduce search time, we keep a cursor for +* each port, walking the shadow tid array to find one that's not +* in use. +* +* For now, if we can't allocate the full list, we fail, although +* in the long run, we'll allocate as many as we can, and the +* caller will deal with that by trying the remaining pages later. +* That means that when we fail, we have to mark the tids as not in +* use again, in our shadow copy. +* +* It's up to the caller to free the tids when they are done. +* We'll unlock the pages as they free them. +* +* Also, right now we are locking one page at a time, but since +* the intended use of this routine is for a single group of +* virtually contiguous pages, that should change to improve +* performance. +*/ +static int ipath_tid_update (struct ipath_portdata *pd, +const struct ipath_tid_info *ti) +{ +int ret =0 , ntids; +u32 tid, porttid, cnt, i, tidcnt; +u16 *tidlist; +struct ipath_devdata *dd = pd->port_dd; +u64 physaddr; +unsigned long vaddr; +u64 __iomem *tidbase; +unsigned long tidmap[8 ]; +struct page **pagep =NULL ; + +if (!dd->ipath_pageshadow) { + ret = -ENOMEM ; + goto done; + } + + cnt = ti->tidcnt; +if (!cnt) { +ipath_dbg ("After copyin, tidcnt 0, tidlist %llx\n" , + (unsigned long long ) ti->tidlist); +/* +* Should we treat as success? likely a bug +*/ + ret = -EFAULT ; + goto done; + } + tidcnt = dd->ipath_rcvtidcnt; +if (cnt >= tidcnt) { +/* make sure it all fits in port_tid_pg_list */ +dev_info (&dd->pcidev->dev,"Process tried to allocate %u " +"TIDs, only trying max (%u)\n" , cnt, tidcnt); + cnt = tidcnt; + } + pagep = (struct page **)pd->port_tid_pg_list; + tidlist = (u16 *) (&pagep[cnt]); + +memset (tidmap,0 ,sizeof (tidmap)); + tid = pd->port_tidcursor; +/* before decrement; chip actual # */ + porttid = pd->port_port * tidcnt; + ntids = tidcnt; + tidbase = (u64 __iomem *) (((char __iomem *) dd->ipath_kregbase) + + dd->ipath_rcvtidbase + + porttid *sizeof (*tidbase)); + +ipath_cdbg (VERBOSE ,"Port%u %u tids, cursor %u, tidbase %p\n" , + pd->port_port, cnt, tid, tidbase); + +/* virtual address of first page in transfer */ + vaddr = ti->tidvaddr; +if (!access_ok (VERIFY_WRITE , (void __user *) vaddr, + cnt *PAGE_SIZE )) { +ipath_dbg ("Fail vaddr %p, %u pages, !access_ok\n" , + (void *)vaddr, cnt); + ret = -EFAULT ; + goto done; + } + ret =ipath_get_user_pages (vaddr, cnt, pagep); +if (ret) { +if (ret == -EBUSY ) { +ipath_dbg ("Failed to lock addr %p, %u pages " +"(already locked)\n" , + (void *) vaddr, cnt); +/* +* for now, continue, and see what happens but with +* the new implementation, this should never happen, +* unless perhaps the user has mpin'ed the pages +* themselves (something we need to test) +*/ + ret =0 ; + }else { +dev_info (&dd->pcidev->dev, +"Failed to lock addr %p, %u pages: " +"errno %d\n" , (void *) vaddr, cnt, -ret); + goto done; + } + } +for (i =0 ; i < cnt; i++, vaddr +=PAGE_SIZE ) { +for (; ntids--; tid++) { +if (tid == tidcnt) + tid =0 ; +if (!dd->ipath_pageshadow[porttid + tid]) +break ; + } +if (ntids <0 ) { +/* +* oops, wrapped all the way through their TIDs, +* and didn't have enough free; see comments at +* start of routine +*/ +ipath_dbg ("Not enough free TIDs for %u pages " +"(index %d), failing\n" , cnt, i); + i--;/* last tidlist[i] not filled in */ + ret = -ENOMEM ; +break ; + } + tidlist[i] = tid; +ipath_cdbg (VERBOSE ,"Updating idx %u to TID %u, " +"vaddr %lx\n" , i, tid, vaddr); +/* we "know" system pages and TID pages are same size */ + dd->ipath_pageshadow[porttid + tid] = pagep[i]; +/* +* don't need atomic or it's overhead +*/ +__set_bit (tid, tidmap); + physaddr =page_to_phys (pagep[i]); + ipath_stats.sps_pagelocks++; +ipath_cdbg (VERBOSE , +"TID %u, vaddr %lx, physaddr %llx pgp %p\n" , + tid, vaddr, (unsigned long long ) physaddr, + pagep[i]); + dd->ipath_f_put_tid (dd, &tidbase[tid],1 , physaddr); +/* +* don't check this tid in ipath_portshadow, since we +* just filled it in; start with the next one. +*/ + tid++; + } + +if (ret) { +u32 limit; + cleanup: +/* jump here if copy out of updated info failed... */ +ipath_dbg ("After failure (ret=%d), undo %d of %d entries\n" , + -ret, i, cnt); +/* same code that's in ipath_free_tid() */ + limit =sizeof (tidmap) *BITS_PER_BYTE ; +if (limit > tidcnt) +/* just in case size changes in future */ + limit = tidcnt; + tid =find_first_bit ((const unsigned long *)tidmap, limit); +for (; tid < limit; tid++) { +if (!test_bit (tid, tidmap)) +continue ; +if (dd->ipath_pageshadow[porttid + tid]) { +ipath_cdbg (VERBOSE ,"Freeing TID %u\n" , + tid); + dd->ipath_f_put_tid (dd, &tidbase[tid],1 , + dd->ipath_tidinvalid); + dd->ipath_pageshadow[porttid + tid] =NULL ; + ipath_stats.sps_pageunlocks++; + } + } +ipath_release_user_pages (pagep, cnt); + }else { +/* +* Copy the updated array, with ipath_tid's filled in, back +* to user. Since we did the copy in already, this "should +* never fail" If it does, we have to clean up... +*/ +if (copy_to_user ((void __user *) + (unsigned long ) ti->tidlist, + tidlist, cnt *sizeof (*tidlist))) { + ret = -EFAULT ; + goto cleanup; + } +if (copy_to_user ((void __user *) (unsigned long ) ti->tidmap, + tidmap,sizeof tidmap)) { + ret = -EFAULT ; + goto cleanup; + } +if (tid == tidcnt) + tid =0 ; + pd->port_tidcursor = tid; + } + +done: +if (ret) +ipath_dbg ("Failed to map %u TID pages, failing with %d\n" , + ti->tidcnt, -ret); +return ret; +} + +/** +* ipath_tid_free - free a port TID +* @pd: the port +* @ti: the TID info +* +* right now we are unlocking one page at a time, but since +* the intended use of this routine is for a single group of +* virtually contiguous pages, that should change to improve +* performance. We check that the TID is in range for this port +* but otherwise don't check validity; if user has an error and +* frees the wrong tid, it's only their own data that can thereby +* be corrupted. We do check that the TID was in use, for sanity +* We always use our idea of the saved address, not the address that +* they pass in to us. +*/ + +static int ipath_tid_free (struct ipath_portdata *pd, +const struct ipath_tid_info *ti) +{ +int ret =0 ; +u32 tid, porttid, cnt, limit, tidcnt; +struct ipath_devdata *dd = pd->port_dd; +u64 __iomem *tidbase; +unsigned long tidmap[8 ]; + +if (!dd->ipath_pageshadow) { + ret = -ENOMEM ; + goto done; + } + +if (copy_from_user (tidmap, (void __user *)(unsigned long )ti->tidmap, +sizeof tidmap)) { + ret = -EFAULT ; + goto done; + } + + porttid = pd->port_port * dd->ipath_rcvtidcnt; + tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvtidbase + + porttid *sizeof (*tidbase)); + + tidcnt = dd->ipath_rcvtidcnt; + limit =sizeof (tidmap) *BITS_PER_BYTE ; +if (limit > tidcnt) +/* just in case size changes in future */ + limit = tidcnt; + tid =find_first_bit (tidmap, limit); +ipath_cdbg (VERBOSE ,"Port%u free %u tids; first bit (max=%d) " +"set is %d, porttid %u\n" , pd->port_port, ti->tidcnt, + limit, tid, porttid); +for (cnt =0 ; tid < limit; tid++) { +/* +* small optimization; if we detect a run of 3 or so without +* any set, use find_first_bit again. That's mainly to +* accelerate the case where we wrapped, so we have some at +* the beginning, and some at the end, and a big gap +* in the middle. +*/ +if (!test_bit (tid, tidmap)) +continue ; + cnt++; +if (dd->ipath_pageshadow[porttid + tid]) { +ipath_cdbg (VERBOSE ,"PID %u freeing TID %u\n" , + pd->port_pid, tid); + dd->ipath_f_put_tid (dd, &tidbase[tid],1 , + dd->ipath_tidinvalid); +ipath_release_user_pages ( + &dd->ipath_pageshadow[porttid + tid],1 ); + dd->ipath_pageshadow[porttid + tid] =NULL ; + ipath_stats.sps_pageunlocks++; + }else +ipath_dbg ("Unused tid %u, ignoring\n" , tid); + } +if (cnt != ti->tidcnt) +ipath_dbg ("passed in tidcnt %d, only %d bits set in map\n" , + ti->tidcnt, cnt); +done: +if (ret) +ipath_dbg ("Failed to unmap %u TID pages, failing with %d\n" , + ti->tidcnt, -ret); +return ret; +} + +/** +* ipath_set_part_key - set a partition key +* @pd: the port +* @key: the key +* +* We can have up to 4 active at a time (other than the default, which is +* always allowed). This is somewhat tricky, since multiple ports may set +* the same key, so we reference count them, and clean up at exit. All 4 +* partition keys are packed into a single infinipath register. It's an +* error for a process to set the same pkey multiple times. We provide no +* mechanism to de-allocate a pkey at this time, we may eventually need to +* do that. I've used the atomic operations, and no locking, and only make +* a single pass through what's available. This should be more than +* adequate for some time. I'll think about spinlocks or the like if and as +* it's necessary. +*/ +static int ipath_set_part_key (struct ipath_portdata *pd,u16 key) +{ +struct ipath_devdata *dd = pd->port_dd; +int i, any =0 , pidx =-1 ; +u16 lkey = key &0x7FFF ; +int ret; + +if (lkey == (IPS_DEFAULT_P_KEY &0x7FFF )) { +/* nothing to do; this key always valid */ + ret =0 ; + goto bail; + } + +ipath_cdbg (VERBOSE ,"p%u try to set pkey %hx, current keys " +"%hx:%x %hx:%x %hx:%x %hx:%x\n" , + pd->port_port, key, dd->ipath_pkeys[0 ], +atomic_read (&dd->ipath_pkeyrefs[0 ]), dd->ipath_pkeys[1 ], +atomic_read (&dd->ipath_pkeyrefs[1 ]), dd->ipath_pkeys[2 ], +atomic_read (&dd->ipath_pkeyrefs[2 ]), dd->ipath_pkeys[3 ], +atomic_read (&dd->ipath_pkeyrefs[3 ])); + +if (!lkey) { +ipath_cdbg (PROC ,"p%u tries to set key 0, not allowed\n" , + pd->port_port); + ret = -EINVAL ; + goto bail; + } + +/* +* Set the full membership bit, because it has to be +* set in the register or the packet, and it seems +* cleaner to set in the register than to force all +* callers to set it. (see bug 4331) +*/ + key |=0x8000 ; + +for (i =0 ; i <ARRAY_SIZE (pd->port_pkeys); i++) { +if (!pd->port_pkeys[i] && pidx ==-1 ) + pidx = i; +if (pd->port_pkeys[i] == key) { +ipath_cdbg (VERBOSE ,"p%u tries to set same pkey " +"(%x) more than once\n" , + pd->port_port, key); + ret = -EEXIST ; + goto bail; + } + } +if (pidx ==-1 ) { +ipath_dbg ("All pkeys for port %u already in use, " +"can't set %x\n" , pd->port_port, key); + ret = -EBUSY ; + goto bail; + } +for (any = i =0 ; i <ARRAY_SIZE (dd->ipath_pkeys); i++) { +if (!dd->ipath_pkeys[i]) { + any++; +continue ; + } +if (dd->ipath_pkeys[i] == key) { +atomic_t *pkrefs = &dd->ipath_pkeyrefs[i]; + +if (atomic_inc_return (pkrefs) >1 ) { + pd->port_pkeys[pidx] = key; +ipath_cdbg (VERBOSE ,"p%u set key %x " +"matches #%d, count now %d\n" , + pd->port_port, key, i, +atomic_read (pkrefs)); + ret =0 ; + goto bail; + }else { +/* +* lost race, decrement count, catch below +*/ +atomic_dec (pkrefs); +ipath_cdbg (VERBOSE ,"Lost race, count was " +"0, after dec, it's %d\n" , +atomic_read (pkrefs)); + any++; + } + } +if ((dd->ipath_pkeys[i] &0x7FFF ) == lkey) { +/* +* It makes no sense to have both the limited and +* full membership PKEY set at the same time since +* the unlimited one will disable the limited one. +*/ + ret = -EEXIST ; + goto bail; + } + } +if (!any) { +ipath_dbg ("port %u, all pkeys already in use, " +"can't set %x\n" , pd->port_port, key); + ret = -EBUSY ; + goto bail; + } +for (any = i =0 ; i <ARRAY_SIZE (dd->ipath_pkeys); i++) { +if (!dd->ipath_pkeys[i] && +atomic_inc_return (&dd->ipath_pkeyrefs[i]) ==1 ) { +u64 pkey; + +/* for ipathstats, etc. */ + ipath_stats.sps_pkeys[i] = lkey; + pd->port_pkeys[pidx] = dd->ipath_pkeys[i] = key; + pkey = + (u64 ) dd->ipath_pkeys[0 ] | + ((u64 ) dd->ipath_pkeys[1 ] <<16 ) | + ((u64 ) dd->ipath_pkeys[2 ] <<32 ) | + ((u64 ) dd->ipath_pkeys[3 ] <<48 ); +ipath_cdbg (PROC ,"p%u set key %x in #%d, " +"portidx %d, new pkey reg %llx\n" , + pd->port_port, key, i, pidx, + (unsigned long long ) pkey); +ipath_write_kreg ( + dd, dd->ipath_kregs->kr_partitionkey, pkey); + + ret =0 ; + goto bail; + } + } +ipath_dbg ("port %u, all pkeys already in use 2nd pass, " +"can't set %x\n" , pd->port_port, key); + ret = -EBUSY ; + +bail: +return ret; +} + +/** +* ipath_manage_rcvq - manage a port's receive queue +* @pd: the port +* @start_stop: action to carry out +* +* start_stop == 0 disables receive on the port, for use in queue +* overflow conditions. start_stop==1 re-enables, to be used to +* re-init the software copy of the head register +*/ +static int ipath_manage_rcvq (struct ipath_portdata *pd,int start_stop) +{ +struct ipath_devdata *dd = pd->port_dd; +u64 tval; + +ipath_cdbg (PROC ,"%sabling rcv for unit %u port %u\n" , + start_stop ?"en" :"dis" , dd->ipath_unit, + pd->port_port); +/* atomically clear receive enable port. */ +if (start_stop) { +/* +* On enable, force in-memory copy of the tail register to +* 0, so that protocol code doesn't have to worry about +* whether or not the chip has yet updated the in-memory +* copy or not on return from the system call. The chip +* always resets it's tail register back to 0 on a +* transition from disabled to enabled. This could cause a +* problem if software was broken, and did the enable w/o +* the disable, but eventually the in-memory copy will be +* updated and correct itself, even in the face of software +* bugs. +*/ + *pd->port_rcvhdrtail_kvaddr =0 ; +set_bit (INFINIPATH_R_PORTENABLE_SHIFT + pd->port_port, + &dd->ipath_rcvctrl); + }else +clear_bit (INFINIPATH_R_PORTENABLE_SHIFT + pd->port_port, + &dd->ipath_rcvctrl); +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); +/* now be sure chip saw it before we return */ + tval =ipath_read_kreg64 (dd, dd->ipath_kregs->kr_scratch); +if (start_stop) { +/* +* And try to be sure that tail reg update has happened too. +* This should in theory interlock with the RXE changes to +* the tail register. Don't assign it to the tail register +* in memory copy, since we could overwrite an update by the +* chip if we did. +*/ + tval =ipath_read_ureg32 (dd, ur_rcvhdrtail, pd->port_port); + } +/* always; new head should be equal to new tail; see above */ +return 0 ; +} + +static void ipath_clean_part_key (struct ipath_portdata *pd, +struct ipath_devdata *dd) +{ +int i, j, pchanged =0 ; +u64 oldpkey; + +/* for debugging only */ + oldpkey = (u64 ) dd->ipath_pkeys[0 ] | + ((u64 ) dd->ipath_pkeys[1 ] <<16 ) | + ((u64 ) dd->ipath_pkeys[2 ] <<32 ) | + ((u64 ) dd->ipath_pkeys[3 ] <<48 ); + +for (i =0 ; i <ARRAY_SIZE (pd->port_pkeys); i++) { +if (!pd->port_pkeys[i]) +continue ; +ipath_cdbg (VERBOSE ,"look for key[%d] %hx in pkeys\n" , i, + pd->port_pkeys[i]); +for (j =0 ; j <ARRAY_SIZE (dd->ipath_pkeys); j++) { +/* check for match independent of the global bit */ +if ((dd->ipath_pkeys[j] &0x7fff ) != + (pd->port_pkeys[i] &0x7fff )) +continue ; +if (atomic_dec_and_test (&dd->ipath_pkeyrefs[j])) { +ipath_cdbg (VERBOSE ,"p%u clear key " +"%x matches #%d\n" , + pd->port_port, + pd->port_pkeys[i], j); + ipath_stats.sps_pkeys[j] = + dd->ipath_pkeys[j] =0 ; + pchanged++; + } +else ipath_cdbg ( +VERBOSE ,"p%u key %x matches #%d, " +"but ref still %d\n" , pd->port_port, + pd->port_pkeys[i], j, +atomic_read (&dd->ipath_pkeyrefs[j])); +break ; + } + pd->port_pkeys[i] =0 ; + } +if (pchanged) { +u64 pkey = (u64 ) dd->ipath_pkeys[0 ] | + ((u64 ) dd->ipath_pkeys[1 ] <<16 ) | + ((u64 ) dd->ipath_pkeys[2 ] <<32 ) | + ((u64 ) dd->ipath_pkeys[3 ] <<48 ); +ipath_cdbg (VERBOSE ,"p%u old pkey reg %llx, " +"new pkey reg %llx\n" , pd->port_port, + (unsigned long long ) oldpkey, + (unsigned long long ) pkey); +ipath_write_kreg (dd, dd->ipath_kregs->kr_partitionkey, + pkey); + } +} + +/** +* ipath_create_user_egr - allocate eager TID buffers +* @pd: the port to allocate TID buffers for +* +* This routine is now quite different for user and kernel, because +* the kernel uses skb's, for the accelerated network performance +* This is the user port version +* +* Allocate the eager TID buffers and program them into infinipath +* They are no longer completely contiguous, we do multiple allocation +* calls. +*/ +static int ipath_create_user_egr (struct ipath_portdata *pd) +{ +struct ipath_devdata *dd = pd->port_dd; +unsigned e, egrcnt, alloced, egrperchunk, chunk, egrsize, egroff; +size_t size; +int ret; + + egrcnt = dd->ipath_rcvegrcnt; +/* TID number offset for this port */ + egroff = pd->port_port * egrcnt; + egrsize = dd->ipath_rcvegrbufsize; +ipath_cdbg (VERBOSE ,"Allocating %d egr buffers, at egrtid " +"offset %x, egrsize %u\n" , egrcnt, egroff, egrsize); + +/* +* to avoid wasting a lot of memory, we allocate 32KB chunks of +* physically contiguous memory, advance through it until used up +* and then allocate more. Of course, we need memory to store those +* extra pointers, now. Started out with 256KB, but under heavy +* memory pressure (creating large files and then copying them over +* NFS while doing lots of MPI jobs), we hit some allocation +* failures, even though we can sleep... (2.6.10) Still get +* failures at 64K. 32K is the lowest we can go without waiting +* more memory again. It seems likely that the coalescing in +* free_pages, etc. still has issues (as it has had previously +* during 2.6.x development). +*/ + size =0x8000 ; + alloced =ALIGN (egrsize * egrcnt, size); + egrperchunk = size / egrsize; + chunk = (egrcnt + egrperchunk -1 ) / egrperchunk; + pd->port_rcvegrbuf_chunks = chunk; + pd->port_rcvegrbufs_perchunk = egrperchunk; + pd->port_rcvegrbuf_size = size; + pd->port_rcvegrbuf =vmalloc (chunk *sizeof (pd->port_rcvegrbuf[0 ])); +if (!pd->port_rcvegrbuf) { + ret = -ENOMEM ; + goto bail; + } + pd->port_rcvegrbuf_phys = +vmalloc (chunk *sizeof (pd->port_rcvegrbuf_phys[0 ])); +if (!pd->port_rcvegrbuf_phys) { + ret = -ENOMEM ; + goto bail_rcvegrbuf; + } +for (e =0 ; e < pd->port_rcvegrbuf_chunks; e++) { +/* +* GFP_USER, but without GFP_FS, so buffer cache can be +* coalesced (we hope); otherwise, even at order 4, +* heavy filesystem activity makes these fail +*/ +gfp_t gfp_flags = __GFP_WAIT | __GFP_IO | __GFP_COMP; + + pd->port_rcvegrbuf[e] =dma_alloc_coherent ( + &dd->pcidev->dev, size, &pd->port_rcvegrbuf_phys[e], + gfp_flags); + +if (!pd->port_rcvegrbuf[e]) { + ret = -ENOMEM ; + goto bail_rcvegrbuf_phys; + } + } + + pd->port_rcvegr_phys = pd->port_rcvegrbuf_phys[0 ]; + +for (e = chunk =0 ; chunk < pd->port_rcvegrbuf_chunks; chunk++) { +dma_addr_t pa = pd->port_rcvegrbuf_phys[chunk]; +unsigned i; + +for (i =0 ; e < egrcnt && i < egrperchunk; e++, i++) { + dd->ipath_f_put_tid (dd, e + egroff + + (u64 __iomem *) + ((char __iomem *) + dd->ipath_kregbase + + dd->ipath_rcvegrbase),0 , pa); + pa += egrsize; + } +cond_resched ();/* don't hog the cpu */ + } + + ret =0 ; + goto bail; + +bail_rcvegrbuf_phys: +for (e =0 ; e < pd->port_rcvegrbuf_chunks && + pd->port_rcvegrbuf[e]; e++) +dma_free_coherent (&dd->pcidev->dev, size, + pd->port_rcvegrbuf[e], + pd->port_rcvegrbuf_phys[e]); + +vfree (pd->port_rcvegrbuf_phys); + pd->port_rcvegrbuf_phys =NULL ; +bail_rcvegrbuf: +vfree (pd->port_rcvegrbuf); + pd->port_rcvegrbuf =NULL ; +bail: +return ret; +} + +static int ipath_do_user_init (struct ipath_portdata *pd, +const struct ipath_user_info *uinfo) +{ +int ret =0 ; +struct ipath_devdata *dd = pd->port_dd; +u64 physaddr, uaddr, off, atmp; +struct page *pagep; +u32 head32; +u64 head; + +/* for now, if major version is different, bail */ +if ((uinfo->spu_userversion >>16 ) !=IPATH_USER_SWMAJOR ) { +dev_info (&dd->pcidev->dev, +"User major version %d not same as driver " +"major %d\n" , uinfo->spu_userversion >>16 , +IPATH_USER_SWMAJOR ); + ret = -ENODEV ; + goto done; + } + +if ((uinfo->spu_userversion &0xffff ) !=IPATH_USER_SWMINOR ) +ipath_dbg ("User minor version %d not same as driver " +"minor %d\n" , uinfo->spu_userversion &0xffff , +IPATH_USER_SWMINOR ); + +if (uinfo->spu_rcvhdrsize) { + ret =ipath_setrcvhdrsize (dd, uinfo->spu_rcvhdrsize); +if (ret) + goto done; + } + +/* for now we do nothing with rcvhdrcnt: uinfo->spu_rcvhdrcnt */ + +/* set up for the rcvhdr Q tail register writeback to user memory */ +if (!uinfo->spu_rcvhdraddr || + !access_ok (VERIFY_WRITE , (u64 __user *) (unsigned long ) + uinfo->spu_rcvhdraddr,sizeof (u64))) { +ipath_dbg ("Port %d rcvhdrtail addr %llx not valid\n" , + pd->port_port, + (unsigned long long ) uinfo->spu_rcvhdraddr); + ret = -EINVAL ; + goto done; + } + + off =offset_in_page (uinfo->spu_rcvhdraddr); + uaddr =PAGE_MASK & (unsigned long ) uinfo->spu_rcvhdraddr; + ret =ipath_get_user_pages_nocopy (uaddr, &pagep); +if (ret) { +dev_info (&dd->pcidev->dev,"Failed to lookup and lock " +"address %llx for rcvhdrtail: errno %d\n" , + (unsigned long long ) uinfo->spu_rcvhdraddr, -ret); + goto done; + } + ipath_stats.sps_pagelocks++; + pd->port_rcvhdrtail_uaddr = uaddr; + pd->port_rcvhdrtail_pagep = pagep; + pd->port_rcvhdrtail_kvaddr = +page_address (pagep); + pd->port_rcvhdrtail_kvaddr += off; + physaddr =page_to_phys (pagep) + off; +ipath_cdbg (VERBOSE ,"port %d user addr %llx hdrtailaddr, %llx " +"physical (off=%llx)\n" , + pd->port_port, + (unsigned long long ) uinfo->spu_rcvhdraddr, + (unsigned long long ) physaddr, (unsigned long long ) off); +ipath_write_kreg_port (dd, dd->ipath_kregs->kr_rcvhdrtailaddr, + pd->port_port, physaddr); + atmp =ipath_read_kreg64_port (dd, + dd->ipath_kregs->kr_rcvhdrtailaddr, + pd->port_port); +if (physaddr != atmp) { +ipath_dev_err (dd, +"Catastrophic software error, " +"RcvHdrTailAddr%u written as %llx, " +"read back as %llx\n" , pd->port_port, + (unsigned long long ) physaddr, + (unsigned long long ) atmp); + ret = -EINVAL ; + goto done; + } + +/* for right now, kernel piobufs are at end, so port 1 is at 0 */ + pd->port_piobufs = dd->ipath_piobufbase + + dd->ipath_pbufsport * (pd->port_port - +1 ) * dd->ipath_palign; +ipath_cdbg (VERBOSE ,"Set base of piobufs for port %u to 0x%x\n" , + pd->port_port, pd->port_piobufs); + +/* +* Now allocate the rcvhdr Q and eager TIDs; skip the TID +* array for time being. If pd->port_port > chip-supported, +* we need to do extra stuff here to handle by handling overflow +* through port 0, someday +*/ + ret =ipath_create_rcvhdrq (dd, pd); +if (!ret) + ret =ipath_create_user_egr (pd); +if (ret) + goto done; +/* enable receives now */ +/* atomically set enable bit for this port */ +set_bit (INFINIPATH_R_PORTENABLE_SHIFT + pd->port_port, + &dd->ipath_rcvctrl); + +/* +* set the head registers for this port to the current values +* of the tail pointers, since we don't know if they were +* updated on last use of the port. +*/ + head32 =ipath_read_ureg32 (dd, ur_rcvhdrtail, pd->port_port); + head = (u64 ) head32; +ipath_write_ureg (dd, ur_rcvhdrhead, head, pd->port_port); + head32 =ipath_read_ureg32 (dd, ur_rcvegrindextail, pd->port_port); +ipath_write_ureg (dd, ur_rcvegrindexhead, head32, pd->port_port); + dd->ipath_lastegrheads[pd->port_port] =-1 ; + dd->ipath_lastrcvhdrqtails[pd->port_port] =-1 ; +ipath_cdbg (VERBOSE ,"Wrote port%d head %llx, egrhead %x from " +"tail regs\n" , pd->port_port, + (unsigned long long ) head, head32); + pd->port_tidcursor =0 ;/* start at beginning after open */ +/* +* now enable the port; the tail registers will be written to memory +* by the chip as soon as it sees the write to +* dd->ipath_kregs->kr_rcvctrl. The update only happens on +* transition from 0 to 1, so clear it first, then set it as part of +* enabling the port. This will (very briefly) affect any other +* open ports, but it shouldn't be long enough to be an issue. +*/ +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl & ~INFINIPATH_R_TAILUPD ); +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); + +done: +return ret; +} + +static int mmap_ureg (struct vm_area_struct *vma,struct ipath_devdata *dd, +u64 ureg) +{ +unsigned long phys; +int ret; + +/* it's the real hardware, so io_remap works */ + +if ((vma->vm_end - vma->vm_start) >PAGE_SIZE ) { +dev_info (&dd->pcidev->dev,"FAIL mmap userreg: reqlen " +"%lx > PAGE\n" , vma->vm_end - vma->vm_start); + ret = -EFAULT ; + }else { + phys = dd->ipath_physaddr + ureg; + vma->vm_page_prot =pgprot_noncached (vma->vm_page_prot); + + vma->vm_flags |=VM_DONTCOPY |VM_DONTEXPAND ; + ret =io_remap_pfn_range (vma, vma->vm_start, + phys >>PAGE_SHIFT , + vma->vm_end - vma->vm_start, + vma->vm_page_prot); + } +return ret; +} + +static int mmap_piobufs (struct vm_area_struct *vma, +struct ipath_devdata *dd, +struct ipath_portdata *pd) +{ +unsigned long phys; +int ret; + +/* +* When we map the PIO buffers, we want to map them as writeonly, no +* read possible. +*/ + +if ((vma->vm_end - vma->vm_start) > + (dd->ipath_pbufsport * dd->ipath_palign)) { +dev_info (&dd->pcidev->dev,"FAIL mmap piobufs: " +"reqlen %lx > PAGE\n" , + vma->vm_end - vma->vm_start); + ret = -EFAULT ; + goto bail; + } + + phys = dd->ipath_physaddr + pd->port_piobufs; +/* +* Do *NOT* mark this as non-cached (PWT bit), or we don't get the +* write combining behavior we want on the PIO buffers! +* vma->vm_page_prot = +* pgprot_noncached(vma->vm_page_prot); +*/ + +if (vma->vm_flags &VM_READ ) { +dev_info (&dd->pcidev->dev, +"Can't map piobufs as readable (flags=%lx)\n" , + vma->vm_flags); + ret = -EPERM ; + goto bail; + } + +/* don't allow them to later change to readable with mprotect */ + + vma->vm_flags &= ~VM_MAYWRITE ; + vma->vm_flags |=VM_DONTCOPY |VM_DONTEXPAND ; + + ret =io_remap_pfn_range (vma, vma->vm_start, phys >>PAGE_SHIFT , + vma->vm_end - vma->vm_start, + vma->vm_page_prot); +bail: +return ret; +} + +static int mmap_rcvegrbufs (struct vm_area_struct *vma, +struct ipath_portdata *pd) +{ +struct ipath_devdata *dd = pd->port_dd; +unsigned long start, size; +size_t total_size, i; +dma_addr_t *phys; +int ret; + +if (!pd->port_rcvegrbuf) { + ret = -EFAULT ; + goto bail; + } + + size = pd->port_rcvegrbuf_size; + total_size = pd->port_rcvegrbuf_chunks * size; +if ((vma->vm_end - vma->vm_start) > total_size) { +dev_info (&dd->pcidev->dev,"FAIL on egr bufs: " +"reqlen %lx > actual %lx\n" , + vma->vm_end - vma->vm_start, + (unsigned long ) total_size); + ret = -EFAULT ; + goto bail; + } + +if (vma->vm_flags &VM_WRITE ) { +dev_info (&dd->pcidev->dev,"Can't map eager buffers as " +"writable (flags=%lx)\n" , vma->vm_flags); + ret = -EPERM ; + goto bail; + } + + start = vma->vm_start; + phys = pd->port_rcvegrbuf_phys; + +/* don't allow them to later change to writeable with mprotect */ + vma->vm_flags &= ~VM_MAYWRITE ; + +for (i =0 ; i < pd->port_rcvegrbuf_chunks; i++, start += size) { + ret =remap_pfn_range (vma, start, phys[i] >>PAGE_SHIFT , + size, vma->vm_page_prot); +if (ret <0 ) + goto bail; + } + ret =0 ; + +bail: +return ret; +} + +static int mmap_rcvhdrq (struct vm_area_struct *vma, +struct ipath_portdata *pd) +{ +struct ipath_devdata *dd = pd->port_dd; +size_t total_size; +int ret; + +/* +* kmalloc'ed memory, physically contiguous; this is from +* spi_rcvhdr_base; we allow user to map read-write so they can +* write hdrq entries to allow protocol code to directly poll +* whether a hdrq entry has been written. +*/ + total_size =ALIGN (dd->ipath_rcvhdrcnt * dd->ipath_rcvhdrentsize * +sizeof (u32),PAGE_SIZE ); +if ((vma->vm_end - vma->vm_start) > total_size) { +dev_info (&dd->pcidev->dev, +"FAIL on rcvhdrq: reqlen %lx > actual %lx\n" , + vma->vm_end - vma->vm_start, + (unsigned long ) total_size); + ret = -EFAULT ; + goto bail; + } + + ret =remap_pfn_range (vma, vma->vm_start, + pd->port_rcvhdrq_phys >>PAGE_SHIFT , + vma->vm_end - vma->vm_start, + vma->vm_page_prot); +bail: +return ret; +} + +static int mmap_pioavailregs (struct vm_area_struct *vma, +struct ipath_portdata *pd) +{ +struct ipath_devdata *dd = pd->port_dd; +int ret; + +/* +* when we map the PIO bufferavail registers, we want to map them as +* readonly, no write possible. +* +* kmalloc'ed memory, physically contiguous, one page only, readonly +*/ + +if ((vma->vm_end - vma->vm_start) >PAGE_SIZE ) { +dev_info (&dd->pcidev->dev,"FAIL on pioavailregs_dma: " +"reqlen %lx > actual %lx\n" , + vma->vm_end - vma->vm_start, + (unsigned long )PAGE_SIZE ); + ret = -EFAULT ; + goto bail; + } + +if (vma->vm_flags &VM_WRITE ) { +dev_info (&dd->pcidev->dev, +"Can't map pioavailregs as writable (flags=%lx)\n" , + vma->vm_flags); + ret = -EPERM ; + goto bail; + } + +/* don't allow them to later change with mprotect */ + vma->vm_flags &= ~VM_MAYWRITE ; + + ret =remap_pfn_range (vma, vma->vm_start, + dd->ipath_pioavailregs_phys >>PAGE_SHIFT , +PAGE_SIZE , vma->vm_page_prot); +bail: +return ret; +} + +/** +* ipath_mmap - mmap various structures into user space +* @fp: the file pointer +* @vma: the VM area +* +* We use this to have a shared buffer between the kernel and the user code +* for the rcvhdr queue, egr buffers, and the per-port user regs and pio +* buffers in the chip. We have the open and close entries so we can bump +* the ref count and keep the driver from being unloaded while still mapped. +*/ +static int ipath_mmap (struct file *fp,struct vm_area_struct *vma) +{ +struct ipath_portdata *pd; +struct ipath_devdata *dd; +u64 pgaddr, ureg; +int ret; + + pd =port_fp (fp); + dd = pd->port_dd; +/* +* This is the ipath_do_user_init() code, mapping the shared buffers +* into the user process. The address referred to by vm_pgoff is the +* virtual, not physical, address; we only do one mmap for each +* space mapped. +*/ + pgaddr = vma->vm_pgoff <<PAGE_SHIFT ; + +/* +* note that ureg does *NOT* have the kregvirt as part of it, to be +* sure that for 32 bit programs, we don't end up trying to map a > +* 44 address. Has to match ipath_get_base_info() code that sets +* __spi_uregbase +*/ + + ureg = dd->ipath_uregbase + dd->ipath_palign * pd->port_port; + +ipath_cdbg (MM ,"ushare: pgaddr %llx vm_start=%lx, vmlen %lx\n" , + (unsigned long long ) pgaddr, vma->vm_start, + vma->vm_end - vma->vm_start); + +if (pgaddr == ureg) + ret =mmap_ureg (vma, dd, ureg); +else if (pgaddr == pd->port_piobufs) + ret =mmap_piobufs (vma, dd, pd); +else if (pgaddr == (u64 ) pd->port_rcvegr_phys) + ret =mmap_rcvegrbufs (vma, pd); +else if (pgaddr == (u64 ) pd->port_rcvhdrq_phys) + ret =mmap_rcvhdrq (vma, pd); +else if (pgaddr == dd->ipath_pioavailregs_phys) + ret =mmap_pioavailregs (vma, pd); +else + ret = -EINVAL ; + + vma->vm_private_data =NULL ; + +if (ret <0 ) +dev_info (&dd->pcidev->dev, +"Failure %d on addr %lx, off %lx\n" , + -ret, vma->vm_start, vma->vm_pgoff); + +return ret; +} + +static unsigned int ipath_poll (struct file *fp, +struct poll_table_struct *pt) +{ +struct ipath_portdata *pd; +u32 head, tail; +int bit; +struct ipath_devdata *dd; + + pd =port_fp (fp); + dd = pd->port_dd; + + bit = pd->port_port +INFINIPATH_R_INTRAVAIL_SHIFT ; +set_bit (bit, &dd->ipath_rcvctrl); + +/* +* Before blocking, make sure that head is still == tail, +* reading from the chip, so we can be sure the interrupt +* enable has made it to the chip. If not equal, disable +* interrupt again and return immediately. This avoids races, +* and the overhead of the chip read doesn't matter much at +* this point, since we are waiting for something anyway. +*/ + +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); + + head =ipath_read_ureg32 (dd, ur_rcvhdrhead, pd->port_port); + tail =ipath_read_ureg32 (dd, ur_rcvhdrtail, pd->port_port); + +if (tail == head) { +set_bit (IPATH_PORT_WAITING_RCV , &pd->port_flag); +poll_wait (fp, &pd->port_wait, pt); + +if (test_bit (IPATH_PORT_WAITING_RCV , &pd->port_flag)) { +/* timed out, no packets received */ +clear_bit (IPATH_PORT_WAITING_RCV , &pd->port_flag); + pd->port_rcvwait_to++; + } + } +else { +/* it's already happened; don't do wait_event overhead */ + pd->port_rcvnowait++; + } + +clear_bit (bit, &dd->ipath_rcvctrl); +ipath_write_kreg (dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); + +return 0 ; +} + +static int try_alloc_port (struct ipath_devdata *dd,int port, +struct file *fp) +{ +int ret; + +if (!dd->ipath_pd[port]) { +void *p, *ptmp; + + p =kzalloc (sizeof (struct ipath_portdata ),GFP_KERNEL ); + +/* +* Allocate memory for use in ipath_tid_update() just once +* at open, not per call. Reduces cost of expected send +* setup. +*/ + ptmp =kmalloc (dd->ipath_rcvtidcnt *sizeof (u16) + + dd->ipath_rcvtidcnt *sizeof (struct page **), +GFP_KERNEL ); +if (!p || !ptmp) { +ipath_dev_err (dd,"Unable to allocate portdata " +"memory, failing open\n" ); + ret = -ENOMEM ; +kfree (p); +kfree (ptmp); + goto bail; + } + dd->ipath_pd[port] = p; + dd->ipath_pd[port]->port_port = port; + dd->ipath_pd[port]->port_dd = dd; + dd->ipath_pd[port]->port_tid_pg_list = ptmp; +init_waitqueue_head (&dd->ipath_pd[port]->port_wait); + } +if (!dd->ipath_pd[port]->port_cnt) { + dd->ipath_pd[port]->port_cnt =1 ; + fp->private_data = (void *) dd->ipath_pd[port]; +ipath_cdbg (PROC ,"%s[%u] opened unit:port %u:%u\n" , + current->comm, current->pid, dd->ipath_unit, + port); + dd->ipath_pd[port]->port_pid = current->pid; +strncpy (dd->ipath_pd[port]->port_comm, current->comm, +sizeof (dd->ipath_pd[port]->port_comm)); + ipath_stats.sps_ports++; + ret =0 ; + goto bail; + } + ret = -EBUSY ; + +bail: +return ret; +} + +static inline int usable (struct ipath_devdata *dd) +{ +return dd && + (dd->ipath_flags &IPATH_PRESENT ) && + dd->ipath_kregbase && + dd->ipath_lid && + !(dd->ipath_flags & (IPATH_LINKDOWN |IPATH_DISABLED + |IPATH_LINKUNK )); +} + +static int find_free_port (int unit,struct file *fp) +{ +struct ipath_devdata *dd =ipath_lookup (unit); +int ret, i; + +if (!dd) { + ret = -ENODEV ; + goto bail; + } + +if (!usable (dd)) { + ret = -ENETDOWN ; + goto bail; + } + +for (i =0 ; i < dd->ipath_cfgports; i++) { + ret =try_alloc_port (dd, i, fp); +if (ret != -EBUSY ) + goto bail; + } + ret = -EBUSY ; + +bail: +return ret; +} + +static int find_best_unit (struct file *fp) +{ +int ret =0 , i, prefunit =-1 , devmax; +int maxofallports, npresent, nup; +int ndev; + + (void )ipath_count_units (&npresent, &nup, &maxofallports); + +/* +* This code is present to allow a knowledgeable person to +* specify the layout of processes to processors before opening +* this driver, and then we'll assign the process to the "closest" +* HT-400 to that processor (we assume reasonable connectivity, +* for now). This code assumes that if affinity has been set +* before this point, that at most one cpu is set; for now this +* is reasonable. I check for both cpus_empty() and cpus_full(), +* in case some kernel variant sets none of the bits when no +* affinity is set. 2.6.11 and 12 kernels have all present +* cpus set. Some day we'll have to fix it up further to handle +* a cpu subset. This algorithm fails for two HT-400's connected +* in tunnel fashion. Eventually this needs real topology +* information. There may be some issues with dual core numbering +* as well. This needs more work prior to release. +*/ +if (!cpus_empty (current->cpus_allowed) && + !cpus_full (current->cpus_allowed)) { +int ncpus =num_online_cpus (), curcpu =-1 ; +for (i =0 ; i < ncpus; i++) +if (cpu_isset (i, current->cpus_allowed)) { +ipath_cdbg (PROC ,"%s[%u] affinity set for " +"cpu %d\n" , current->comm, + current->pid, i); + curcpu = i; + } +if (curcpu !=-1 ) { +if (npresent) { + prefunit = curcpu / (ncpus / npresent); +ipath_dbg ("%s[%u] %d chips, %d cpus, " +"%d cpus/chip, select unit %d\n" , + current->comm, current->pid, + npresent, ncpus, ncpus / npresent, + prefunit); + } + } + } + +/* +* user ports start at 1, kernel port is 0 +* For now, we do round-robin access across all chips +*/ + +if (prefunit !=-1 ) + devmax = prefunit +1 ; +else + devmax =ipath_count_units (NULL ,NULL ,NULL ); +recheck: +for (i =1 ; i < maxofallports; i++) { +for (ndev = prefunit !=-1 ? prefunit :0 ; ndev < devmax; + ndev++) { +struct ipath_devdata *dd =ipath_lookup (ndev); + +if (!usable (dd)) +continue ;/* can't use this unit */ +if (i >= dd->ipath_cfgports) +/* +* Maxed out on users of this unit. Try +* next. +*/ +continue ; + ret =try_alloc_port (dd, i, fp); +if (!ret) + goto done; + } + } + +if (npresent) { +if (nup ==0 ) { + ret = -ENETDOWN ; +ipath_dbg ("No ports available (none initialized " +"and ready)\n" ); + }else { +if (prefunit >0 ) { +/* if started above 0, retry from 0 */ +ipath_cdbg (PROC , +"%s[%u] no ports on prefunit " +"%d, clear and re-check\n" , + current->comm, current->pid, + prefunit); + devmax =ipath_count_units (NULL ,NULL , +NULL ); + prefunit =-1 ; + goto recheck; + } + ret = -EBUSY ; +ipath_dbg ("No ports available\n" ); + } + }else { + ret = -ENXIO ; +ipath_dbg ("No boards found\n" ); + } + +done: +return ret; +} + +static int ipath_open (struct inode *in,struct file *fp) +{ +int ret, minor; + +mutex_lock (&ipath_mutex); + + minor =iminor (in); +ipath_cdbg (VERBOSE ,"open on dev %lx (minor %d)\n" , + (long )in->i_rdev, minor); + +if (minor) + ret =find_free_port (minor -1 , fp); +else + ret =find_best_unit (fp); + +mutex_unlock (&ipath_mutex); +return ret; +} + +/** +* unlock_exptid - unlock any expected TID entries port still had in use +* @pd: port +* +* We don't actually update the chip here, because we do a bulk update +* below, using ipath_f_clear_tids. +*/ +static void unlock_expected_tids (struct ipath_portdata *pd) +{ +struct ipath_devdata *dd = pd->port_dd; +int port_tidbase = pd->port_port * dd->ipath_rcvtidcnt; +int i, cnt =0 , maxtid = port_tidbase + dd->ipath_rcvtidcnt; + +ipath_cdbg (VERBOSE ,"Port %u unlocking any locked expTID pages\n" , + pd->port_port); +for (i = port_tidbase; i < maxtid; i++) { +if (!dd->ipath_pageshadow[i]) +continue ; + +ipath_release_user_pages_on_close (&dd->ipath_pageshadow[i], +1 ); + dd->ipath_pageshadow[i] =NULL ; + cnt++; + ipath_stats.sps_pageunlocks++; + } +if (cnt) +ipath_cdbg (VERBOSE ,"Port %u locked %u expTID entries\n" , + pd->port_port, cnt); + +if (ipath_stats.sps_pagelocks || ipath_stats.sps_pageunlocks) +ipath_cdbg (VERBOSE ,"%llu pages locked, %llu unlocked\n" , + (unsigned long long ) ipath_stats.sps_pagelocks, + (unsigned long long ) + ipath_stats.sps_pageunlocks); +} + +static int ipath_close (struct inode *in,struct file *fp) +{ +int ret =0 ; +struct ipath_portdata *pd; +struct ipath_devdata *dd; +unsigned port; + +ipath_cdbg (VERBOSE ,"close on dev %lx, private data %p\n" , + (long )in->i_rdev, fp->private_data); + +mutex_lock (&ipath_mutex); + + pd =port_fp (fp); + port = pd->port_port; + fp->private_data =NULL ; + dd = pd->port_dd; + +if (pd->port_hdrqfull) { +ipath_cdbg (PROC ,"%s[%u] had %u rcvhdrqfull errors " +"during run\n" , pd->port_comm, pd->port_pid, + pd->port_hdrqfull); + pd->port_hdrqfull =0 ; + } + +if (pd->port_rcvwait_to || pd->port_piowait_to + || pd->port_rcvnowait || pd->port_pionowait) { +ipath_cdbg (VERBOSE ,"port%u, %u rcv, %u pio wait timeo; " +"%u rcv %u, pio already\n" , + pd->port_port, pd->port_rcvwait_to, + pd->port_piowait_to, pd->port_rcvnowait, + pd->port_pionowait); + pd->port_rcvwait_to = pd->port_piowait_to = + pd->port_rcvnowait = pd->port_pionowait =0 ; + } +if (pd->port_flag) { +ipath_dbg ("port %u port_flag still set to 0x%lx\n" , + pd->port_port, pd->port_flag); + pd->port_flag =0 ; + } + +if (dd->ipath_kregbase) { +if (pd->port_rcvhdrtail_uaddr) { + pd->port_rcvhdrtail_uaddr =0 ; + pd->port_rcvhdrtail_kvaddr =NULL ; +ipath_release_user_pages_on_close ( + &pd->port_rcvhdrtail_pagep,1 ); + pd->port_rcvhdrtail_pagep =NULL ; + ipath_stats.sps_pageunlocks++; + } +ipath_write_kreg_port ( + dd, dd->ipath_kregs->kr_rcvhdrtailaddr, + port,0ULL ); +ipath_write_kreg_port ( + dd, dd->ipath_kregs->kr_rcvhdraddr, + pd->port_port,0 ); + +/* clean up the pkeys for this port user */ +ipath_clean_part_key (pd, dd); + +if (port < dd->ipath_cfgports) { +int i = dd->ipath_pbufsport * (port -1 ); +ipath_disarm_piobufs (dd, i, dd->ipath_pbufsport); + +/* atomically clear receive enable port. */ +clear_bit (INFINIPATH_R_PORTENABLE_SHIFT + port, + &dd->ipath_rcvctrl); +ipath_write_kreg ( + dd, + dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); + +if (dd->ipath_pageshadow) +unlock_expected_tids (pd); + ipath_stats.sps_ports--; +ipath_cdbg (PROC ,"%s[%u] closed port %u:%u\n" , + pd->port_comm, pd->port_pid, + dd->ipath_unit, port); + } + } + + pd->port_cnt =0 ; + pd->port_pid =0 ; + + dd->ipath_f_clear_tids (dd, pd->port_port); + +ipath_free_pddata (dd, pd->port_port,0 ); + +mutex_unlock (&ipath_mutex); + +return ret; +} + +static int ipath_port_info (struct ipath_portdata *pd, +struct ipath_port_info __user *uinfo) +{ +struct ipath_port_info info; +int nup; +int ret; + + (void )ipath_count_units (NULL , &nup,NULL ); + info.num_active = nup; + info.unit = pd->port_dd->ipath_unit; + info.port = pd->port_port; + +if (copy_to_user (uinfo, &info,sizeof (info))) { + ret = -EFAULT ; + goto bail; + } + ret =0 ; + +bail: +return ret; +} + +static ssize_t ipath_write (struct file *fp,const char __user *data, +size_t count,loff_t *off) +{ +const struct ipath_cmd __user *ucmd; +struct ipath_portdata *pd; +const void __user *src; +size_t consumed, copy; +struct ipath_cmd cmd; +ssize_t ret =0 ; +void *dest; + +if (count <sizeof (cmd.type)) { + ret = -EINVAL ; + goto bail; + } + + ucmd = (const struct ipath_cmd __user *) data; + +if (copy_from_user (&cmd.type, &ucmd->type,sizeof (cmd.type))) { + ret = -EFAULT ; + goto bail; + } + + consumed =sizeof (cmd.type); + +switch (cmd.type) { +case IPATH_CMD_USER_INIT : + copy =sizeof (cmd.cmd.user_info); + dest = &cmd.cmd.user_info; + src = &ucmd->cmd.user_info; +break ; +case IPATH_CMD_RECV_CTRL : + copy =sizeof (cmd.cmd.recv_ctrl); + dest = &cmd.cmd.recv_ctrl; + src = &ucmd->cmd.recv_ctrl; +break ; +case IPATH_CMD_PORT_INFO : + copy =sizeof (cmd.cmd.port_info); + dest = &cmd.cmd.port_info; + src = &ucmd->cmd.port_info; +break ; +case IPATH_CMD_TID_UPDATE : +case IPATH_CMD_TID_FREE : + copy =sizeof (cmd.cmd.tid_info); + dest = &cmd.cmd.tid_info; + src = &ucmd->cmd.tid_info; +break ; +case IPATH_CMD_SET_PART_KEY : + copy =sizeof (cmd.cmd.part_key); + dest = &cmd.cmd.part_key; + src = &ucmd->cmd.part_key; +break ; +default : + ret = -EINVAL ; + goto bail; + } + +if ((count - consumed) < copy) { + ret = -EINVAL ; + goto bail; + } + +if (copy_from_user (dest, src, copy)) { + ret = -EFAULT ; + goto bail; + } + + consumed += copy; + pd =port_fp (fp); + +switch (cmd.type) { +case IPATH_CMD_USER_INIT : + ret =ipath_do_user_init (pd, &cmd.cmd.user_info); +if (ret <0 ) + goto bail; + ret =ipath_get_base_info ( + pd, (void __user *) (unsigned long ) + cmd.cmd.user_info.spu_base_info, + cmd.cmd.user_info.spu_base_info_size); +break ; +case IPATH_CMD_RECV_CTRL : + ret =ipath_manage_rcvq (pd, cmd.cmd.recv_ctrl); +break ; +case IPATH_CMD_PORT_INFO : + ret =ipath_port_info (pd, + (struct ipath_port_info __user *) + (unsigned long ) cmd.cmd.port_info); +break ; +case IPATH_CMD_TID_UPDATE : + ret =ipath_tid_update (pd, &cmd.cmd.tid_info); +break ; +case IPATH_CMD_TID_FREE : + ret =ipath_tid_free (pd, &cmd.cmd.tid_info); +break ; +case IPATH_CMD_SET_PART_KEY : + ret =ipath_set_part_key (pd, cmd.cmd.part_key); +break ; + } + +if (ret >=0 ) + ret = consumed; + +bail: +return ret; +} + +static struct class *ipath_class; + +static int init_cdev (int minor,char *name,struct file_operations *fops, +struct cdev **cdevp,struct class_device **class_devp) +{ +const dev_t dev =MKDEV (IPATH_MAJOR , minor); +struct cdev *cdev =NULL ; +struct class_device *class_dev =NULL ; +int ret; + + cdev =cdev_alloc (); +if (!cdev) { + printk(KERN_ERR IPATH_DRV_NAME +": Could not allocate cdev for minor %d, %s\n" , + minor, name); + ret = -ENOMEM ; + goto done; + } + + cdev->owner =THIS_MODULE ; + cdev->ops = fops; +kobject_set_name (&cdev->kobj, name); + + ret =cdev_add (cdev, dev,1 ); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME +": Could not add cdev for minor %d, %s (err %d)\n" , + minor, name, -ret); + goto err_cdev; + } + + class_dev =class_device_create (ipath_class,NULL , dev,NULL , name); + +if (IS_ERR (class_dev)) { + ret =PTR_ERR (class_dev); + printk(KERN_ERR IPATH_DRV_NAME ": Could not create " +"class_dev for minor %d, %s (err %d)\n" , + minor, name, -ret); + goto err_cdev; + } + + goto done; + +err_cdev: +cdev_del (cdev); + cdev =NULL ; + +done: +if (ret >=0 ) { + *cdevp = cdev; + *class_devp = class_dev; + }else { + *cdevp =NULL ; + *class_devp =NULL ; + } + +return ret; +} + +int ipath_cdev_init (int minor,char *name,struct file_operations *fops, +struct cdev **cdevp,struct class_device **class_devp) +{ +return init_cdev (minor, name, fops, cdevp, class_devp); +} + +static void cleanup_cdev (struct cdev **cdevp, +struct class_device **class_devp) +{ +struct class_device *class_dev = *class_devp; + +if (class_dev) { +class_device_unregister (class_dev); + *class_devp =NULL ; + } + +if (*cdevp) { +cdev_del (*cdevp); + *cdevp =NULL ; + } +} + +void ipath_cdev_cleanup (struct cdev **cdevp, +struct class_device **class_devp) +{ +cleanup_cdev (cdevp, class_devp); +} + +static struct cdev *wildcard_cdev; +static struct class_device *wildcard_class_dev; + +static const dev_t dev =MKDEV (IPATH_MAJOR ,0 ); + +static int user_init (void ) +{ +int ret; + + ret =register_chrdev_region (dev,IPATH_NMINORS ,IPATH_DRV_NAME ); +if (ret <0 ) { + printk(KERN_ERR IPATH_DRV_NAME ": Could not register " + "chrdev region (err %d)\n", -ret); + goto done; + } + + ipath_class =class_create (THIS_MODULE ,IPATH_DRV_NAME ); + +if (IS_ERR (ipath_class)) { + ret =PTR_ERR (ipath_class); + printk(KERN_ERR IPATH_DRV_NAME ": Could not create " + "device class (err %d)\n", -ret); + goto bail; + } + + goto done; +bail: +unregister_chrdev_region (dev,IPATH_NMINORS ); +done: +return ret; +} + +static void user_cleanup (void ) +{ +if (ipath_class) { +class_destroy (ipath_class); + ipath_class =NULL ; + } + +unregister_chrdev_region (dev,IPATH_NMINORS ); +} + +static atomic_t user_count =ATOMIC_INIT (0 ); +static atomic_t user_setup =ATOMIC_INIT (0 ); + +int ipath_user_add (struct ipath_devdata *dd) +{ +char name[10 ]; +int ret; + +if (atomic_inc_return (&user_count) ==1 ) { + ret =user_init (); +if (ret <0 ) { +ipath_dev_err (dd,"Unable to set up user support: " +"error %d\n" , -ret); + goto bail; + } + ret =ipath_diag_init (); +if (ret <0 ) { +ipath_dev_err (dd,"Unable to set up diag support: " +"error %d\n" , -ret); + goto bail_sma; + } + + ret =init_cdev (0 ,"ipath" , &ipath_file_ops, &wildcard_cdev, + &wildcard_class_dev); +if (ret <0 ) { +ipath_dev_err (dd,"Could not create wildcard " +"minor: error %d\n" , -ret); + goto bail_diag; + } + +atomic_set (&user_setup,1 ); + } + +snprintf (name,sizeof (name),"ipath%d" , dd->ipath_unit); + + ret =init_cdev (dd->ipath_unit +1 , name, &ipath_file_ops, + &dd->cdev, &dd->class_dev); +if (ret <0 ) +ipath_dev_err (dd,"Could not create user minor %d, %s\n" , + dd->ipath_unit +1 , name); + + goto bail; + +bail_diag: +ipath_diag_cleanup (); +bail_sma: +user_cleanup (); +bail: +return ret; +} + +void ipath_user_del (struct ipath_devdata *dd) +{ +cleanup_cdev (&dd->cdev, &dd->class_dev); + +if (atomic_dec_return (&user_count) ==0 ) { +if (atomic_read (&user_setup) ==0 ) + goto bail; + +cleanup_cdev (&wildcard_cdev, &wildcard_class_dev); +ipath_diag_cleanup (); +user_cleanup (); + +atomic_set (&user_setup,0 ); + } +bail: +return ; +}
drivers/infiniband/hw/ipath/ipath_user_pages.c new file +207 -0
207 lines not on this page · raw message
PATCH 1/1 ipath - misc infiniband code, part 1
In reply to Bryan O'SullivanCompletion queues, local and remote memory keys, and memory region support.
drivers/infiniband/hw/ipath/ipath_cq.c new file +295 -0
@@ -0,0 +1,295 @@ +/* +* Copyright (c) 2005, 2006 PathScale, Inc. All rights reserved. +* +* This software is available to you under a choice of one of two +* licenses. You may choose to be licensed under the terms of the GNU +* General Public License (GPL) Version 2, available from the file +* COPYING in the main directory of this source tree, or the +* OpenIB.org BSD license below: +* +* Redistribution and use in source and binary forms, with or +* without modification, are permitted provided that the following +* conditions are met: +* +* - Redistributions of source code must retain the above +* copyright notice, this list of conditions and the following +* disclaimer. +* +* - Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials +* provided with the distribution. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND +* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS +* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN +* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN +* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE +* SOFTWARE. +*/ + +#include <linux/err.h> +#include <linux/vmalloc.h> + +#include "ipath_verbs.h" + +/** +* ipath_cq_enter - add a new entry to the completion queue +* @cq: completion queue +* @entry: work completion entry to add +* @sig: true if @entry is a solicitated entry +* +* This may be called with one of the qp->s_lock or qp->r_rq.lock held. +*/ +void ipath_cq_enter (struct ipath_cq *cq,struct ib_wc *entry,int solicited) +{ +unsigned long flags; +u32 next; + +spin_lock_irqsave (&cq->lock, flags); + +if (cq->head == cq->ibcq.cqe) + next =0 ; +else + next = cq->head +1 ; +if (unlikely (next == cq->tail)) { +spin_unlock_irqrestore (&cq->lock, flags); +if (cq->ibcq.event_handler) { +struct ib_event ev; + + ev.device = cq->ibcq.device; + ev.element.cq = &cq->ibcq; + ev.event =IB_EVENT_CQ_ERR ; + cq->ibcq.event_handler (&ev, cq->ibcq.cq_context); + } +return ; + } + cq->queue[cq->head] = *entry; + cq->head = next; + +if (cq->notify ==IB_CQ_NEXT_COMP || + (cq->notify ==IB_CQ_SOLICITED && solicited)) { + cq->notify =IB_CQ_NONE ; + cq->triggered++; +/* +* This will cause send_complete() to be called in +* another thread. +*/ +tasklet_hi_schedule (&cq->comptask); + } + +spin_unlock_irqrestore (&cq->lock, flags); + +if (entry->status !=IB_WC_SUCCESS ) +to_idev (cq->ibcq.device)->n_wqe_errs++; +} + +/** +* ipath_poll_cq - poll for work completion entries +* @ibcq: the completion queue to poll +* @num_entries: the maximum number of entries to return +* @entry: pointer to array where work completions are placed +* +* Returns the number of completion entries polled. +* +* This may be called from interrupt context. Also called by ib_poll_cq() +* in the generic verbs code. +*/ +int ipath_poll_cq (struct ib_cq *ibcq,int num_entries,struct ib_wc *entry) +{ +struct ipath_cq *cq =to_icq (ibcq); +unsigned long flags; +int npolled; + +spin_lock_irqsave (&cq->lock, flags); + +for (npolled =0 ; npolled < num_entries; ++npolled, ++entry) { +if (cq->tail == cq->head) +break ; + *entry = cq->queue[cq->tail]; +if (cq->tail == cq->ibcq.cqe) + cq->tail =0 ; +else + cq->tail++; + } + +spin_unlock_irqrestore (&cq->lock, flags); + +return npolled; +} + +static void send_complete (unsigned long data) +{ +struct ipath_cq *cq = (struct ipath_cq *)data; + +/* +* The completion handler will most likely rearm the notification +* and poll for all pending entries. If a new completion entry +* is added while we are in this routine, tasklet_hi_schedule() +* won't call us again until we return so we check triggered to +* see if we need to call the handler again. +*/ +for (;;) { +u8 triggered = cq->triggered; + + cq->ibcq.comp_handler (&cq->ibcq, cq->ibcq.cq_context); + +if (cq->triggered == triggered) +return ; + } +} + +/** +* ipath_create_cq - create a completion queue +* @ibdev: the device this completion queue is attached to +* @entries: the minimum size of the completion queue +* @context: unused by the InfiniPath driver +* @udata: unused by the InfiniPath driver +* +* Returns a pointer to the completion queue or negative errno values +* for failure. +* +* Called by ib_create_cq() in the generic verbs code. +*/ +struct ib_cq *ipath_create_cq (struct ib_device *ibdev,int entries, +struct ib_ucontext *context, +struct ib_udata *udata) +{ +struct ipath_cq *cq; +struct ib_wc *wc; +struct ib_cq *ret; + +/* +* Need to use vmalloc() if we want to support large #s of +* entries. +*/ + cq =kmalloc (sizeof (*cq),GFP_KERNEL ); +if (!cq) { + ret =ERR_PTR (-ENOMEM ); + goto bail; + } + +/* +* Need to use vmalloc() if we want to support large #s of entries. +*/ + wc =vmalloc (sizeof (*wc) * (entries +1 )); +if (!wc) { +kfree (cq); + ret =ERR_PTR (-ENOMEM ); + goto bail; + } +/* +* ib_create_cq() will initialize cq->ibcq except for cq->ibcq.cqe. +* The number of entries should be >= the number requested or return +* an error. +*/ + cq->ibcq.cqe = entries; + cq->notify =IB_CQ_NONE ; + cq->triggered =0 ; +spin_lock_init (&cq->lock); +tasklet_init (&cq->comptask, send_complete, (unsigned long )cq); + cq->head =0 ; + cq->tail =0 ; + cq->queue = wc; + + ret = &cq->ibcq; + +bail: +return ret; +} + +/** +* ipath_destroy_cq - destroy a completion queue +* @ibcq: the completion queue to destroy. +* +* Returns 0 for success. +* +* Called by ib_destroy_cq() in the generic verbs code. +*/ +int ipath_destroy_cq (struct ib_cq *ibcq) +{ +struct ipath_cq *cq =to_icq (ibcq); + +tasklet_kill (&cq->comptask); +vfree (cq->queue); +kfree (cq); + +return 0 ; +} + +/** +* ipath_req_notify_cq - change the notification type for a completion queue +* @ibcq: the completion queue +* @notify: the type of notification to request +* +* Returns 0 for success. +* +* This may be called from interrupt context. Also called by +* ib_req_notify_cq() in the generic verbs code. +*/ +int ipath_req_notify_cq (struct ib_cq *ibcq,enum ib_cq_notify notify) +{ +struct ipath_cq *cq =to_icq (ibcq); +unsigned long flags; + +spin_lock_irqsave (&cq->lock, flags); +/* +* Don't change IB_CQ_NEXT_COMP to IB_CQ_SOLICITED but allow +* any other transitions. +*/ +if (cq->notify !=IB_CQ_NEXT_COMP ) + cq->notify = notify; +spin_unlock_irqrestore (&cq->lock, flags); +return 0 ; +} + +int ipath_resize_cq (struct ib_cq *ibcq,int cqe,struct ib_udata *udata) +{ +struct ipath_cq *cq =to_icq (ibcq); +struct ib_wc *wc, *old_wc; +u32 n; +int ret; + +/* +* Need to use vmalloc() if we want to support large #s of entries. +*/ + wc =vmalloc (sizeof (*wc) * (cqe +1 )); +if (!wc) { + ret = -ENOMEM ; + goto bail; + } + +spin_lock_irq (&cq->lock); +if (cq->head < cq->tail) + n = cq->ibcq.cqe +1 + cq->head - cq->tail; +else + n = cq->head - cq->tail; +if (unlikely ((u32 )cqe < n)) { +spin_unlock_irq (&cq->lock); +vfree (wc); + ret = -EOVERFLOW ; + goto bail; + } +for (n =0 ; cq->tail != cq->head; n++) { + wc[n] = cq->queue[cq->tail]; +if (cq->tail == cq->ibcq.cqe) + cq->tail =0 ; +else + cq->tail++; + } + cq->ibcq.cqe = cqe; + cq->head = n; + cq->tail =0 ; + old_wc = cq->queue; + cq->queue = wc; +spin_unlock_irq (&cq->lock); + +vfree (old_wc); + + ret =0 ; + +bail: +return ret; +}
drivers/infiniband/hw/ipath/ipath_keys.c new file +236 -0
236 lines not on this page · raw message
drivers/infiniband/hw/ipath/ipath_mr.c new file +383 -0
383 lines not on this page · raw message
drivers/infiniband/hw/ipath/ipath_srq.c new file +273 -0
273 lines not on this page · raw message