Promise SATA driver
I can't find any readme in the Documentation folder about this, and I remember the original 'promise drivers goes gpl' thread degenerating into a license discussion.
I've got a 378 s150 tx chipset with their fasttrak raid bios. How should I configure the drives to use with the 2.6.3 kernel promise SATA driver? Can I configure them as a raid array?
TIA
Andrew Walrond
Quoted 1 line · Andrew Walrond
I've got a 378 s150 tx chipset with their fasttrak raid bios. How should I configure the drives to use with the 2.6.3 kernel promise SATA driver? Can I configure them as a raid array?
The 2.6.3 sata_promise driver ignores any RAID configuration you set up, and directly talks to the drives.
Jeff
Quoted 7 lines · Jeff Garzik
Quoted 3 lines · Andrew Walrond
I've got a 378 s150 tx chipset with their fasttrak raid bios. How should I configure the drives to use with the 2.6.3 kernel promise SATA driver? Can I configure them as a raid array?
The 2.6.3
sata_promisedriver ignores any RAID configuration you set up, and directly talks to the drives.
To boot off one you might have to setup a RAID configuration in the card BIOS though (Which is why I have a single drive configured as a raid0 :-) )
Quoted 10 lines · Pekka Pietikainen
Quoted 5 lines · Jeff Garzik
Quoted 1 line · Andrew Walrond
I've got a 378 s150 tx chipset with their fasttrak raid bios. How should I configure the drives to use with the 2.6.3 kernel promise SATA driver? Can I configure them as a raid array?
The 2.6.3
sata_promisedriver ignores any RAID configuration you set up, and directly talks to the drives.To boot off one you might have to setup a RAID configuration in the card BIOS though (Which is why I have a single drive configured as a raid0 :-) )
Hum, the BIOS works fine here with no arrays defined...
Jeff
I take it the software raid thing wasn't part of the gpl'ed driver, and isn't something that is likely to happen?
Andrew Walrond
Quoted 1 line · Andrew Walrond
I take it the software raid thing wasn't part of the gpl'ed driver, and isn't something that is likely to happen?
In 2.4, RAID0 and RAID1 are supported via the pdcraid driver.
In 2.6, Promise software RAID support does not exist. In conversations with Promise, we all agreed to encourage and support the standard Linux RAID, md.
Jeff
Quoted 9 lines · Jeff Garzik
Quoted 1 line · Andrew Walrond
I take it the software raid thing wasn't part of the gpl'ed driver, and isn't something that is likely to happen?
In 2.4, RAID0 and RAID1 are supported via the pdcraid driver.
In 2.6, Promise software RAID support does not exist. In conversations with Promise, we all agreed to encourage and support the standard Linux RAID, md.
Jeff
Does that apply to the FastTrack S150 SX4 aswell? The hardware XOR-engine will not be used? What about the onboard cache?
// Henrik Gustafsson
Quoted 10 lines · Henrik Gustafsson
Quoted 8 lines · Jeff Garzik
Quoted 1 line · Andrew Walrond
I take it the software raid thing wasn't part of the gpl'ed driver, and isn't something that is likely to happen?
In 2.4, RAID0 and RAID1 are supported via the pdcraid driver.
Quoted 7 lines
Quoted 3 lines
In 2.6, Promise software RAID support does not exist. In conversations with Promise, we all agreed to encourage and support the standard Linux RAID, md.
Jeff
Does that apply to the FastTrack S150 SX4 aswell? The hardware XOR-engine will not be used? What about the onboard cache?
I'm glad you asked.
The SX4 is a very different story. The hardware XOR engine and on-board cache are not currently used, but they will be in the future.
For the TX series, there is no on-board cache, so hardware XOR engine isn't very useful. For the SX series, it is very useful.
Promise did some neat stuff with the SX4... so neat it takes some thinking to figure out how to best implement it in Linux :)
Jeff
Quoted 22 lines · Jeff Garzik
Quoted 10 lines · Henrik Gustafsson
Quoted 8 lines · Jeff Garzik
Quoted 1 line · Andrew Walrond
I take it the software raid thing wasn't part of the gpl'ed driver, and isn't something that is likely to happen?
In 2.4, RAID0 and RAID1 are supported via the pdcraid driver.
Quoted 7 lines
Quoted 3 lines
In 2.6, Promise software RAID support does not exist. In conversations with Promise, we all agreed to encourage and support the standard Linux RAID, md.
Jeff
Does that apply to the FastTrack S150 SX4 aswell? The hardware XOR-engine will not be used? What about the onboard cache?
I'm glad you asked.
Quoted 8 lines
The SX4 is a very different story. The hardware XOR engine and on-board cache are not currently used, but they will be in the future.
For the TX series, there is no on-board cache, so hardware XOR engine isn't very useful. For the SX series, it is very useful.
Promise did some neat stuff with the SX4... so neat it takes some thinking to figure out how to best implement it in Linux :)
Jeff
I'm glad for that particular response :)
I happen to have such a card in a computer here. Right now it's not used for anything in particular (waiting for things to stabilising a bit) so I can test out patches without worrying about any data on it, so feel free to suggest things to try.
Is there any active development done on it?
My current working conditions (and lack of specs for the card) prevents me from doing much work on it myself atm, but is there perhaps another way of following the development on that part a bit more closely?
I have done my (small, but still... :) ) share of driver development and low-level coding (company I work for makes me write code for their embedded devices and sometimes drivers for the PC-interfaces) so I might just be able to pitch in with an idea or two.
// Henrik Gustafsson
Quoted 6 lines · Henrik Gustafsson
I happen to have such a card in a computer here. Right now it's not used for anything in particular (waiting for things to stabilising a bit) so I can test out patches without worrying about any data on it, so feel free to suggest things to try.
Is there any active development done on it?
Well, the basic SX4 SATA driver is pretty much done. There is one bugfix I need to merge for PCI-X, but that's it.
Unfortunately, it is a bit slower than average since every request must bounce through RAM first, with no queueing.
Using the on-board DIMM as a write-through cache would boost performance significantly.
Quoted 8 lines
My current working conditions (and lack of specs for the card) prevents me from doing much work on it myself atm, but is there perhaps another way of following the development on that part a bit more closely?
I have done my (small, but still... :) ) share of driver development and low-level coding (company I work for makes me write code for their embedded devices and sometimes drivers for the PC-interfaces) so I might just be able to pitch in with an idea or two.
Well, the specs are under NDA but are available from Promise.
However... if you want to tackle creating the write-through cache, that shouldn't require any specs at all. If you are knowledgeable enough to create generic write-through cache code for an ATA drive, that's sufficient :)
Jeff
In article <[email protected]>,
Quoted 6 lines · Jeff Garzik
Quoted 2 lines · Andrew Walrond
I take it the software raid thing wasn't part of the gpl'ed driver, and isn't something that is likely to happen?
In 2.4, RAID0 and RAID1 are supported via the pdcraid driver.
I looked at those drivers, but they don't support error recovery in RAID1 mode of any kind. It's just "read from one drive, write to both" but if one disk goes south you're SOL.
Just FYI ;)
Mike.
A message that is not in the archive (sent off-list or not yet received): mit.lcs.mail.linux-kernel/[email protected]
Quoted 3 lines · Jeff Garzik
In 2.6, Promise software RAID support does not exist. In conversations with Promise, we all agreed to encourage and support the standard Linux RAID, md.
Does this mean a dual-boot Linux/Windows system cannot use a Promise RAID?
- Pat
Quoted 10 lines · Patrick J. LoPresti
Quoted 3 lines · Jeff Garzik
In 2.6, Promise software RAID support does not exist. In conversations with Promise, we all agreed to encourage and support the standard Linux RAID, md.
Does this mean a dual-boot Linux/Windows system cannot use a Promise RAID?
In 2.4, you can use pdcraid driver.
In 2.6, correct, there is no Promise RAID driver.
Jeff