hda: 92xx S/PDIF In support
PATCH 1/1 hda: 92xx S/PDIF In support
Add support for S/PDIF IN on reference boards quirks. Also disable the IEC958 capture switch on boards with GPIO0 enabled.
Signed-off-by Matthew Ranostay <[email protected]>
---
pci/hda/patch_sigmatel.c +20 -12
@@ -1245,7 +1245,7 @@ static int stac92xx_build_controls(struct hda_codec *codec)return err; spec->multiout.share_spdif =1 ; } -if (spec->dig_in_nid) { +if (spec->dig_in_nid && (!spec->gpio_dir &0x01 )) { err =snd_hda_create_spdif_in_ctls (codec, spec->dig_in_nid);if (err <0 )return err;
@@ -4075,10 +4075,6 @@ again:memcpy (&spec->private_dimux, &stac92hd73xx_dmux,sizeof (stac92hd73xx_dmux)); -/* GPIO0 High = Enable EAPD */ - spec->eapd_mask = spec->gpio_mask = spec->gpio_dir =0x1 ; - spec->gpio_data =0x01 ; -switch (spec->board_config) {case STAC_DELL_M6 : spec->init = dell_eq_core_init;
@@ -4118,6 +4114,11 @@ again: spec->num_dmics =STAC92HD73XX_NUM_DMICS ; spec->num_smuxes =ARRAY_SIZE (stac92hd73xx_smux_nids); } +if (spec->board_config >STAC_92HD73XX_REF ) { +/* GPIO0 High = Enable EAPD */ + spec->eapd_mask = spec->gpio_mask = spec->gpio_dir =0x1 ; + spec->gpio_data =0x01 ; + } spec->dinput_mux = &spec->private_dimux; spec->num_pwrs =ARRAY_SIZE (stac92hd73xx_pwr_nids);
@@ -4354,10 +4355,12 @@ again: spec->aloopback_mask =0x20 ; spec->aloopback_shift =0 ; -/* GPIO0 High = EAPD */ - spec->gpio_mask =0x01 ; - spec->gpio_dir =0x01 ; - spec->gpio_data =0x01 ; +if (spec->board_config >STAC_92HD71BXX_REF ) { +/* GPIO0 = EAPD */ + spec->gpio_mask =0x01 ; + spec->gpio_dir =0x01 ; + spec->gpio_data =0x01 ; + } spec->powerdown_adcs =1 ; spec->digbeep_nid =0x26 ;
@@ -4599,9 +4602,11 @@ static int patch_stac927x(struct hda_codec *codec) spec->num_dmuxes =ARRAY_SIZE (stac927x_dmux_nids);break ;default : -/* GPIO0 High = Enable EAPD */ - spec->eapd_mask = spec->gpio_mask = spec->gpio_dir =0x1 ; - spec->gpio_data =0x01 ; +if (spec->board_config >STAC_D965_REF ) { +/* GPIO0 High = Enable EAPD */ + spec->eapd_mask = spec->gpio_mask =0x01 ; + spec->gpio_dir = spec->gpio_data =0x01 ; + } spec->num_dmics =0 ; spec->init = stac927x_core_init;
@@ -4715,6 +4720,9 @@ static int patch_stac9205(struct hda_codec *codec)*/ spec->gpio_data =0x01 ;break ; +case STAC_9205_REF : +/* SPDIF-In enabled */ +break ;default :/* GPIO0 High = EAPD */ spec->eapd_mask = spec->gpio_mask = spec->gpio_dir =0x1 ;
Takashi Iwai
AppliedAt Fri, 26 Sep 2008 10:06:40 -0400,
Quoted 5 lines · Matthew Ranostay
Add support for S/PDIF IN on reference boards quirks. Also disable the IEC958 capture switch on boards with GPIO0 enabled.
Signed-off-by Matthew Ranostay <[email protected]>
Applied. Thanks.
Takashi