Skip to contentSkip to conversation

Problem with ncurses and alsamixer (cannot open terminal: vt100 or xterm)

DISCUSSION David Topper 2 participants 2 messages Jun 2, 2007 – Jun 4, 2007

lore
Share & tools
lore
#0 lore raw

I finally managed to get the alsa-1.0.4 utils to compile on an ARM based SBC. When I launch alsamixer, however, I get an error:

Error opening terminal: xterm

When I ssh into the board. Or:

Error opening terminal: vt100

When connected via serial cable.

I suspect this has something to do with the linking (or lack thereof) of alsamixer for ncurses. The ncurrses library, by the way, I cross compiled with the following command:

CC=/opt/crosstool/arm-unknown-linux-gnu/gcc-3.3.4-glibc-2.3.2/bin/arm-unknown-linux-gnu-gcc ./configure --host=arm-linux --prefix=/home/topper/ts-packages/ --exec-prefix=/home/topper/ts-packages/

But for the alsa utils, I simple ran ./configure, and the script detected the ncurses library, ran through and compiled. Yet, something seems amuck because:

root@ts7000:root# ldd /bin/alsamixer
        libasound.so.2 => /lib/libasound.so.2 (0x2aac8000)
        libm.so.6 => /lib/libm.so.6 (0x2ab6f000)
        libdl.so.2 => /lib/libdl.so.2 (0x2abe9000)
        libpthread.so.0 => /lib/libpthread.so.0 (0x2abf3000)
        libc.so.6 => /lib/libc.so.6 (0x2ac4b000)
        /lib/ld-linux.so.2 => /lib/ld-linux.so.2 (0x2aaab000)

Whereas on my Linux Intel laptop:

awn:~$ ldd /usr/bin/alsamixer
        libncurses.so.5 => /lib/libncurses.so.5 (0x4002c000)
        libasound.so.2 => /usr/lib/libasound.so.2 (0x40069000)
        libm.so.6 => /lib/libm.so.6 (0x4010d000)
        libdl.so.2 => /lib/libdl.so.2 (0x40130000)
        libpthread.so.0 => /lib/libpthread.so.0 (0x40133000)
        libc.so.6 => /lib/libc.so.6 (0x40184000)
        /lib/ld-linux.so.2 => /lib/ld-linux.so.2 (0x40000000)

So I have two questions:

1. How might ensure proper linking of the ncurses library.
2. Is there another way to tell alsa to activate various cards, set volume, etc.. so I can test to see if the alsa driver is even working on this board.

Thanks,

Dave Topper

Signature · 2 lines
Technical Director - Virginia Center for Computer Music
http://www.virginia.edu/music/VCCM/
#1 lore raw

At Sat, 02 Jun 2007 16:34:12 -0400,

Quoted 43 lines · David Topper

I finally managed to get the alsa-1.0.4 utils to compile on an ARM based SBC. When I launch alsamixer, however, I get an error:

Error opening terminal: xterm

When I ssh into the board. Or:

Error opening terminal: vt100

When connected via serial cable.

I suspect this has something to do with the linking (or lack thereof) of alsamixer for ncurses. The ncurrses library, by the way, I cross compiled with the following command:

CC=/opt/crosstool/arm-unknown-linux-gnu/gcc-3.3.4-glibc-2.3.2/bin/arm-unknown-linux-gnu-gcc ./configure --host=arm-linux --prefix=/home/topper/ts-packages/ --exec-prefix=/home/topper/ts-packages/

But for the alsa utils, I simple ran ./configure, and the script detected the ncurses library, ran through and compiled. Yet, something seems amuck because:

root@ts7000:root# ldd /bin/alsamixer
        libasound.so.2 => /lib/libasound.so.2 (0x2aac8000)
        libm.so.6 => /lib/libm.so.6 (0x2ab6f000)
        libdl.so.2 => /lib/libdl.so.2 (0x2abe9000)
        libpthread.so.0 => /lib/libpthread.so.0 (0x2abf3000)
        libc.so.6 => /lib/libc.so.6 (0x2ac4b000)
        /lib/ld-linux.so.2 => /lib/ld-linux.so.2 (0x2aaab000)

Whereas on my Linux Intel laptop:

awn:~$ ldd /usr/bin/alsamixer
        libncurses.so.5 => /lib/libncurses.so.5 (0x4002c000)
        libasound.so.2 => /usr/lib/libasound.so.2 (0x40069000)
        libm.so.6 => /lib/libm.so.6 (0x4010d000)
        libdl.so.2 => /lib/libdl.so.2 (0x40130000)
        libpthread.so.0 => /lib/libpthread.so.0 (0x40133000)
        libc.so.6 => /lib/libc.so.6 (0x40184000)
        /lib/ld-linux.so.2 => /lib/ld-linux.so.2 (0x40000000)
Quoted 3 lines

So I have two questions:

1. How might ensure proper linking of the ncurses library.

Give --with-curses option.
You might be using non-standard curses library.

Quoted 3 lines

2. Is there another way to tell alsa to activate various cards, set volume, etc.. so I can test to see if the alsa driver is even working on this board.

Use amixer to list/set/get mixer elements only with command line.

And, above all:

3. any reason to use the ancient ALSA 1.0.4?

Takashi