Skip to contentSkip to conversation

capture with non-interleaved mode

DISCUSSION [email protected] 3 participants 6 messages Oct 14, 2003 – Oct 16, 2003

lore
Share & tools
lore
#0 lore raw

Hi. I'm developping a signal processing program which needs to compute data from each channel of soundcards separately.
After searches I found that I must open the soundcard with the SND_PCM_ACCESS_RW_NONINTERLEAVED flag but it doesn't works well : for each readn operation i get the -32 error code . Meanwhile, I tested capture in interleaved mode and it works well.
I had to use hw:x,y for the interleaved capture and plughw:x,y for the non- interleaved capture, I don't know if non-interleaved capture works with hw:x,y.

Any advice (or piece of source code) ?

Thanks,

Cyril Coquilleau

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#1 lore raw
Quoted 8 lines

Hi. I'm developping a signal processing program which needs to compute data from each channel of soundcards separately.
After searches I found that I must open the soundcard with the SND_PCM_ACCESS_RW_NONINTERLEAVED flag but it doesn't works well : for each readn operation i get the -32 error code . Meanwhile, I tested capture in interleaved mode and it works well.
I had to use hw:x,y for the interleaved capture and plughw:x,y for the non- interleaved capture, I don't know if non-interleaved capture works with hw:x,y.

[ We need a FAQ ... ]

ALSA's "hw" devices can only be used with parameters that match capabilities offered by the underlying hardware. There's not much hardware out there that supports non-interleaved I/O, so as a result, most "hw" devices can't do this. The Hammerfall and ice1712 series are notable exceptions. But there is a corollary: if you were using a hammerfall, the "hw" device cannot do interleaved I/O either.

as to your error, its probably a bug in your code. JACK uses non-interleaved mode by default, and it works with both plughw and hw models of many different kinds. if you posted the relevant parts of it here, somebody can probably help you.

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#2 lore raw
Quoted 22 lines
Quoted 9 lines

Hi. I'm developping a signal processing program which needs to compute data

from each channel of soundcards separately.
After searches I found that I must open the soundcard with the SND_PCM_ACCESS_RW_NONINTERLEAVED flag but it doesn't works well : for each

readn operation i get the -32 error code . Meanwhile, I tested capture in interleaved mode and it works well.
I had to use hw:x,y for the interleaved capture and plughw:x,y for the

non-

Quoted 1 line

interleaved capture, I don't know if non-interleaved capture works with

hw:x,y.

[ We need a FAQ ... ]

ALSA's "hw" devices can only be used with parameters that match capabilities offered by the underlying hardware. There's not much hardware out there that supports non-interleaved I/O, so as a result, most "hw" devices can't do this. The Hammerfall and ice1712 series are notable exceptions. But there is a corollary: if you were using a hammerfall, the "hw" device cannot do interleaved I/O either.

Quoted 6 lines

as to your error, its probably a bug in your code. JACK uses non-interleaved mode by default, and it works with both plughw and hw models of many different kinds. if you posted the relevant parts of it here, somebody can probably help you.

I join the relevant parts of the source (without error handlers) :

#define BUF_SIZE 128

struct snd_card
{
snd_pcm_t *handle;
snd_pcm_hw_params_t *params;

short inputBuffer[BUF_SIZE*2];
void *buffer[2];
};
typedef struct snd_card snd_card_t;

int
main (....)
{
char card_id[32];
int err;
itn card = 0;
snd_card_t *card1;

  card1 = calloc(1,sizeof(snd_card_t));
  card1->buffer[0] = card1->inputBuffer;
  card1->buffer[1] = &card1->inputBuffer[BUF_SIZE];
  snprintf (card_id, 32, "plughw:%d", card);

snd_pcm_open (&card1->handle, card_id, SND_PCM_STREAM_CAPTURE, 0); snd_pcm_hw_params_malloc (&card1->params); snd_pcm_hw_params_any (card1->handle, card1->params); snd_pcm_hw_params_set_channels (card1->handle, card1->params, 2); snd_pcm_hw_params_set_access (card1->handle, card1->params,
SND_PCM_ACCESS_RW_NONINTERLEAVED);
snd_pcm_hw_params_set_format (card1->handle, card1->params,
SND_PCM_FORMAT_S16_LE);
snd_pcm_hw_params_set_rate_near (card1->handle, card1->params, ECHANT, 0); snd_pcm_hw_params (card1->handle, card1->params); snd_pcm_hw_params_free (card1->params);
snd_pcm_prepare (card1->handle);

while (...)

  {
    err = snd_pcm_readn (card1->handle, card1->buffer, BUF_SIZE);
    printf("err=%d, buff=%d\n", err, card1->buffer[0]);
    ...

}
...
}

And here is the result of printf
err=-32, buff=-1
err=-32, buff=-1
err=-32, buff=-1
err=-32, buff=-1
err=-32, buff=-1

If you see the problem...

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#3 lore raw

At Tue, 14 Oct 2003 17:30:40 +0200,

Quoted 75 lines · [email protected] wrote:
Quoted 23 lines
Quoted 10 lines

Hi. I'm developping a signal processing program which needs to compute data

from each channel of soundcards separately.
After searches I found that I must open the soundcard with the SND_PCM_ACCESS_RW_NONINTERLEAVED flag but it doesn't works well : for each

readn operation i get the -32 error code . Meanwhile, I tested capture in interleaved mode and it works well.
I had to use hw:x,y for the interleaved capture and plughw:x,y for the

non-

Quoted 1 line

interleaved capture, I don't know if non-interleaved capture works with

hw:x,y.

[ We need a FAQ ... ]

ALSA's "hw" devices can only be used with parameters that match capabilities offered by the underlying hardware. There's not much hardware out there that supports non-interleaved I/O, so as a result, most "hw" devices can't do this. The Hammerfall and ice1712 series are notable exceptions. But there is a corollary: if you were using a hammerfall, the "hw" device cannot do interleaved I/O either.

Quoted 6 lines

as to your error, its probably a bug in your code. JACK uses non-interleaved mode by default, and it works with both plughw and hw models of many different kinds. if you posted the relevant parts of it here, somebody can probably help you.

I join the relevant parts of the source (without error handlers) :

#define BUF_SIZE 128

struct snd_card
{
snd_pcm_t *handle;
snd_pcm_hw_params_t *params;

short inputBuffer[BUF_SIZE*2];
void *buffer[2];
};
typedef struct snd_card snd_card_t;

int
main (....)
{
char card_id[32];
int err;
itn card = 0;
snd_card_t *card1;

  card1 = calloc(1,sizeof(snd_card_t));
  card1->buffer[0] = card1->inputBuffer;
  card1->buffer[1] = &card1->inputBuffer[BUF_SIZE];
  snprintf (card_id, 32, "plughw:%d", card);

snd_pcm_open (&card1->handle, card_id, SND_PCM_STREAM_CAPTURE, 0); snd_pcm_hw_params_malloc (&card1->params); snd_pcm_hw_params_any (card1->handle, card1->params); snd_pcm_hw_params_set_channels (card1->handle, card1->params, 2); snd_pcm_hw_params_set_access (card1->handle, card1->params,
SND_PCM_ACCESS_RW_NONINTERLEAVED);
snd_pcm_hw_params_set_format (card1->handle, card1->params,
SND_PCM_FORMAT_S16_LE);
snd_pcm_hw_params_set_rate_near (card1->handle, card1->params, ECHANT, 0); snd_pcm_hw_params (card1->handle, card1->params); snd_pcm_hw_params_free (card1->params);
snd_pcm_prepare (card1->handle);

while (...)

  {
    err = snd_pcm_readn (card1->handle, card1->buffer, BUF_SIZE);
    printf("err=%d, buff=%d\n", err, card1->buffer[0]);
    ...
Quoted 8 lines

}
...
}

And here is the result of printf
err=-32, buff=-1

-32 is EPIPE. it's likely buffer under/overrun.

Takashi

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#4 lore raw
Quoted 86 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line

Hi. I'm developping a signal processing program which needs to compute

data

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

from each channel of soundcards separately.
After searches I found that I must open the soundcard with the SND_PCM_ACCESS_RW_NONINTERLEAVED flag but it doesn't works well : for

each

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

readn operation i get the -32 error code . Meanwhile, I tested capture

in

Quoted 4 lines
Quoted 4 lines
Quoted 2 lines

interleaved mode and it works well.
I had to use hw:x,y for the interleaved capture and plughw:x,y for the

non-

Quoted 1 line

interleaved capture, I don't know if non-interleaved capture works

with

Quoted 46 lines
Quoted 11 lines

hw:x,y.

[ We need a FAQ ... ]

ALSA's "hw" devices can only be used with parameters that match capabilities offered by the underlying hardware. There's not much hardware out there that supports non-interleaved I/O, so as a result, most "hw" devices can't do this. The Hammerfall and ice1712 series are notable exceptions. But there is a corollary: if you were using a hammerfall, the "hw" device cannot do interleaved I/O either.

Quoted 6 lines

as to your error, its probably a bug in your code. JACK uses non-interleaved mode by default, and it works with both plughw and hw models of many different kinds. if you posted the relevant parts of it here, somebody can probably help you.

I join the relevant parts of the source (without error handlers) :

#define BUF_SIZE 128
#define ECHANT 44100

struct snd_card
{
snd_pcm_t *handle;
snd_pcm_hw_params_t *params;

short inputBuffer[BUF_SIZE*2];
void *buffer[2];
};
typedef struct snd_card snd_card_t;

int
main (....)
{
char card_id[32];
int err;
itn card = 0;
snd_card_t *card1;

  card1 = calloc(1,sizeof(snd_card_t));
  card1->buffer[0] = card1->inputBuffer;
  card1->buffer[1] = &card1->inputBuffer[BUF_SIZE];
  snprintf (card_id, 32, "plughw:%d", card);
Quoted 9 lines

snd_pcm_open (&card1->handle, card_id, SND_PCM_STREAM_CAPTURE, 0); snd_pcm_hw_params_malloc (&card1->params); snd_pcm_hw_params_any (card1->handle, card1->params); snd_pcm_hw_params_set_channels (card1->handle, card1->params, 2); snd_pcm_hw_params_set_access (card1->handle, card1->params,
SND_PCM_ACCESS_RW_NONINTERLEAVED);
snd_pcm_hw_params_set_format (card1->handle, card1->params,
SND_PCM_FORMAT_S16_LE);
snd_pcm_hw_params_set_rate_near (card1->handle, card1->params, ECHANT,

0);

Quoted 15 lines
  snd_pcm_hw_params (card1->handle, card1->params);
  snd_pcm_hw_params_free (card1->params);
  snd_pcm_prepare (card1->handle);

while (...)

  {
    err = snd_pcm_readn (card1->handle, card1->buffer, BUF_SIZE);
    printf("err=%d, buff=%d\n", err, card1->buffer[0]);
    ...

}
...
}

Quoted 6 lines
Quoted 2 lines

And here is the result of printf
err=-32, buff=-1

-32 is EPIPE. it's likely buffer under/overrun.

I've not managed to fix this bug into my program... Do you see the error on my code (bad soundcard initialization or other) or have you got another way to propose me to capture the two channels of my soundcard separately ?

Cyril

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#5 lore raw
Quoted 4 lines

I've not managed to fix this bug into my program... Do you see the error on my

code (bad soundcard initialization or other) or have you got another way to propose me to capture the two channels of my soundcard separately ?

try increasing BUF_SIZE to 4096 and see what happens. 128 frames/period is in seriously low-latency territory, and i doubt that your program is designed for that. if i was to make a guess, you probably try to write to disk after reading from the audio interface, in the same thread, yes? sorry, you can't do that for 128 frames/period, and a general design rule, you shouldn't ever do it (though it obviously works for some simple programs with just stereo in).

--p

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php