irq 7: nobody cared! (intel8x0 sound / 2.6.2-rc3-mm1)
Got this when tried to run mplayer (mplayer played something audible for 1 sec and then stalled):
irq 7: nobody cared!
Call Trace: [<c010c0f4>] __report_bad_irq+0x24/0x80 [<c010c1d1>] note_interrupt+0x61/0x90 [<c010c46d>] do_IRQ+0x10d/0x120 [<c0279e1c>] common_interrupt+0x18/0x20 [<c010c093>] handle_IRQ_event+0x23/0x60 [<c010c3e3>] do_IRQ+0x83/0x120 [<c0279e1c>] common_interrupt+0x18/0x20
handlers:
[<f99a1720>] (snd_intel8x0_interrupt+0x0/0x1e0 [snd_intel8x0]) Disabling IRQ #7
sound module in use is intel8x0 as seen above. Chip itself is nforce2 integrated audio.
I know there were problems earlier with this chip and new ALSA, but thought maybe this is helpful. The kernel is booted with pci=noacpi due to recent problems with nforce2 mb's using -mm series kernels.
It worked flawlessly in 2.6.1-rc1-mm1.
Lenar
At Fri, 06 Feb 2004 18:19:52 +0200,
Quoted 14 lines · Lenar Lõhmus
Got this when tried to run mplayer (mplayer played something audible for 1 sec and then stalled):
irq 7: nobody cared!
Call Trace: [<c010c0f4>] __report_bad_irq+0x24/0x80 [<c010c1d1>] note_interrupt+0x61/0x90 [<c010c46d>] do_IRQ+0x10d/0x120 [<c0279e1c>] common_interrupt+0x18/0x20 [<c010c093>] handle_IRQ_event+0x23/0x60 [<c010c3e3>] do_IRQ+0x83/0x120 [<c0279e1c>] common_interrupt+0x18/0x20
Quoted 6 lines
handlers:
[<f99a1720>] (snd_intel8x0_interrupt+0x0/0x1e0[snd_intel8x0]) Disabling IRQ #7sound module in use is intel8x0 as seen above. Chip itself is nforce2 integrated audio.
could you check the status register value when this happens with the attached patch?
--
Takashi Iwai <[email protected]> ALSA Developer - www.alsa-project.org
sound/pci/intel8x0.c +1 -0
@@ -807,6 +807,7 @@if (status)iputdword (chip, chip->int_sta_reg, status);spin_unlock (&chip->reg_lock); +printk (KERN_DEBUG "intel8x0: ignored irq, status = 0x%x, sta_mask = 0x%x\n" , status, chip->int_sta_mask);return IRQ_NONE ; }
Quoted 5 lines · Takashi Iwai
could you check the status register value when this happens with the attached patch?
It never happened after applying this patch (not the right circumstances I think). It always printed this:
intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
And sound worked.
Today discovered this message from dmesg:
intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0 irq 7: nobody cared!
Call Trace: [<c010c0f4>] __report_bad_irq+0x24/0x80 [<c010c1d1>] note_interrupt+0x61/0x90 [<c010c46d>] do_IRQ+0x10d/0x120 [<c0279e1c>] common_interrupt+0x18/0x20 [<c010c093>] handle_IRQ_event+0x23/0x60 [<c010c3e3>] do_IRQ+0x83/0x120 [<c0279e1c>] common_interrupt+0x18/0x20 [<f99a97dc>] dl_done_list+0x7c/0x110 [ohci_hcd] [<f99aa114>] ohci_irq+0x84/0x160 [ohci_hcd] [<f99ade79>] nic_irq+0x1a9/0x1d0 [forcedeth] [<f996d52e>] usb_hcd_irq+0x2e/0x60 [usbcore] [<c010c09f>] handle_IRQ_event+0x2f/0x60 [<c010c3e3>] do_IRQ+0x83/0x120 [<c0107000>] _stext+0x0/0x50 [<c0279e1c>] common_interrupt+0x18/0x20 [<c0107000>] _stext+0x0/0x50 [<c0108b53>] default_idle+0x23/0x30 [<c0108bbc>] cpu_idle+0x2c/0x40 [<c02fe70a>] start_kernel+0x13a/0x150 [<c02fe480>] unknown_bootoption+0x0/0x100
handlers:
[<f99a1720>] (snd_intel8x0_interrupt+0x0/0x200 [snd_intel8x0]) Disabling IRQ #7
And mplayer stalls again. The 'ignored irq' message was the same and no additional messages after call trace.
/proc/interrupts:
CPU0
0: 78008640 XT-PIC timer 1: 35441 XT-PIC i8042 2: 0 XT-PIC cascade 5: 18501105 XT-PIC eth1 7: 203478 XT-PIC NVidia nForce2 8: 22814379 XT-PIC rtc 9: 0 XT-PIC acpi 11: 639763 XT-PIC ide2, ehci_hcd 12: 47894522 XT-PIC ohci_hcd, eth0 14: 589578 XT-PIC ide0 15: 115750 XT-PIC ide1 NMI: 0 LOC: 78015575 ERR: 3478 MIS: 0
Lenar
At Tue, 10 Feb 2004 19:26:19 +0200,
Quoted 13 lines · Lenar Lõhmus
Quoted 5 lines · Takashi Iwai
could you check the status register value when this happens with the attached patch?
It never happened after applying this patch (not the right circumstances I think). It always printed this:
intel8x0: ignored irq, status =
0x300100,sta_mask=0xf0
Quoted 8 lines
And sound worked.
Today discovered this message from dmesg:
intel8x0: ignored irq, status =
0x300100,sta_mask=0xf0
intel8x0: ignored irq, status =0x300100,sta_mask=0xf0
intel8x0: ignored irq, status =0x300100,sta_mask=0xf0irq 7: nobody cared!
ok then really some unknown status bits are set. the attached patch should fix this problem anyway.
Takashi
sound/pci/intel8x0.c +1 -1
@@ -807,7 +807,7 @@if (status)iputdword (chip, chip->int_sta_reg, status);spin_unlock (&chip->reg_lock); -return IRQ_NONE ; +return IRQ_HANDLED (status); }for (i =0 ; i < chip->bdbars_count; i++) {
Moins,
sound/pci/intel8x0.c line 810
Quoted 11 lines · * On Tue, 10 Feb 2004 20:05:35 +0100, Takashi Iwai <[email protected]> said:
ok then really some unknown status bits are set. the attached patch should fix this problem anyway.
sound/pci/intel8x0.c +1
-1@@ -807,7 +807,7 @@if (status)iputdword (chip, chip->int_sta_reg, status);spin_unlock (&chip->reg_lock); -return IRQ_NONE ; +return IRQ_HANDLED (status);
did not compile, tried
return IRQ_RETVAL(status);
instead. Works, but I get 150,000 interrupts/s even without playing any sound.
thanks,
Ralf
Signature · 3 lines
P: Linus Torvalds patch-2.2.4 -S: Buried alive in diapers +S: Buried alive in reporters
Quoted 14 lines · Ralf Gerbig
sound/pci/intel8x0.c line 810
Quoted 8 lines · * On Tue, 10 Feb 2004 20:05:35 +0100, Takashi Iwai <[email protected]> said:
sound/pci/intel8x0.c +1
-1@@ -807,7 +807,7 @@if (status)iputdword (chip, chip->int_sta_reg, status);spin_unlock (&chip->reg_lock); -return IRQ_NONE ; +return IRQ_HANDLED (status);did not compile, tried
Quoted 4 lines
return IRQ_RETVAL(status);instead. Works, but I get 150,000 interrupts/s even without playing any sound.
Can you add something like
static int count = 10;
if (count) {
count--;
printk("sound status = %08x (mask %08x)\n",
status, chip->int_sta_mask);
}to just before the return?
That should tell what the register contents are, and might be a clue about what event it thinks is active.
Linus
Moins,
Quoted 9 lines · Linus Torvalds
Can you add something like
static int count = 10; if (count) { count--; printk("sound status = %08x (mask %08x)\n", status, chip->int_sta_mask); }
Quoted 4 lines
to just before the return?
That should tell what the register contents are, and might be a clue about what event it thinks is active.
kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
kernel: sound status = 00000000 (mask 00000000)
kernel: sound status = 00000000 (mask 00000000)
kernel: sound status = 00300100 (mask 000000f0)
last message repeated 7 times
/sbin/hotplug[18871]: no runnable /etc/hotplug/sound.agent is installed /sbin/hotplug[18886]: no runnable /etc/hotplug/sound.agent is installed /sbin/hotplug[18878]: no runnable /etc/hotplug/sound.agent is installed /sbin/hotplug[18885]: no runnable /etc/hotplug/sound.agent is installed
kernel: intel8x0_measure_ac97_clock: measured 49492 usecs
kernel: intel8x0: clocking to 47354
kernel: ALSA sound/pci/intel8x0.c:2787: joystick(s) found /sbin/hotplug[18901]: no runnable /etc/hotplug/sound.agent is installed
playing a video with mplayer:
kernel: ALSA sound/core/pcm_lib.c:233: Unexpected hw_pointer value [2] (stream = 0, delta: -1108, max jitter = 4456): wrong interrupt acknowledge?
Signature · 3 lines
P: Linus Torvalds patch-2.2.4 -S: Buried alive in diapers +S: Buried alive in reporters
At 10 Feb 2004 21:49:19 +0100,
Quoted 34 lines · Ralf Gerbig
Moins,
Quoted 9 lines · Linus Torvalds
Can you add something like
static int count = 10; if (count) { count--; printk("sound status = %08x (mask %08x)\n", status, chip->int_sta_mask); }Quoted 4 lines
to just before the return?
That should tell what the register contents are, and might be a clue about what event it thinks is active.
kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
kernel: sound status = 00000000 (mask 00000000)
kernel: sound status = 00000000 (mask 00000000)
kernel: sound status = 00300100 (mask000000f0)
last message repeated 7 times
/sbin/hotplug[18871]: no runnable/etc/hotplug/sound.agentis installed /sbin/hotplug[18886]: no runnable/etc/hotplug/sound.agentis installed /sbin/hotplug[18878]: no runnable/etc/hotplug/sound.agentis installed /sbin/hotplug[18885]: no runnable/etc/hotplug/sound.agentis installed
kernel:intel8x0_measure_ac97_clock: measured 49492 usecs
kernel: intel8x0: clocking to 47354
kernel: ALSAsound/pci/intel8x0.c:2787: joystick(s) found /sbin/hotplug[18901]: no runnable/etc/hotplug/sound.agentis installed
Quoted 3 lines
playing a video with mplayer:
kernel: ALSA
sound/core/pcm_lib.c:233: Unexpectedhw_pointervalue [2] (stream = 0, delta: -1108, max jitter = 4456): wrong interrupt acknowledge?
this is likely a different problem.
usually this message appears when the interrupt handling is sloppy.
--
Takashi Iwai <[email protected]> ALSA Developer - www.alsa-project.org
Moins,
Quoted 33 lines · * On Wed, 11 Feb 2004 11:42:14 +0100, Takashi Iwai <[email protected]> said:
Quoted 31 lines · Ralf Gerbig
Quoted 9 lines · Linus Torvalds
Can you add something like
static int count = 10; if (count) { count--; printk("sound status = %08x (mask %08x)\n", status, chip->int_sta_mask); }Quoted 4 lines
to just before the return?
That should tell what the register contents are, and might be a clue about what event it thinks is active.
kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
kernel: sound status = 00000000 (mask 00000000)
kernel: sound status = 00000000 (mask 00000000)
kernel: sound status = 00300100 (mask000000f0)
last message repeated 7 times
/sbin/hotplug[18871]: no runnable/etc/hotplug/sound.agentis installed /sbin/hotplug[18886]: no runnable/etc/hotplug/sound.agentis installed /sbin/hotplug[18878]: no runnable/etc/hotplug/sound.agentis installed /sbin/hotplug[18885]: no runnable/etc/hotplug/sound.agentis installed
kernel:intel8x0_measure_ac97_clock: measured 49492 usecs
kernel: intel8x0: clocking to 47354
kernel: ALSAsound/pci/intel8x0.c:2787: joystick(s) found /sbin/hotplug[18901]: no runnable/etc/hotplug/sound.agentis installed
Quoted 6 lines
Quoted 3 lines
playing a video with mplayer:
kernel: ALSA
sound/core/pcm_lib.c:233: Unexpectedhw_pointervalue [2] (stream = 0, delta: -1108, max jitter = 4456): wrong interrupt acknowledge?this is likely a different problem.
usually this message appears when the interrupt handling is sloppy.
tried this: ( beware I do _not_ know what I'm doing)
oss/i810_audio.c 2004-02-11 20:48:51.000000000 +0100 renamed from oss/i810_audio.c.orig 2004-02-11 20:13:45.000000000 +0100 +10 -2
@@ -149,7 +149,7 @@ //#define DEBUG //#define DEBUG2 -//#define DEBUG_INTERRUPTS +#define DEBUG_INTERRUPTS //#define DEBUG_MMAP //#define DEBUG_MMIO
@@ -1380,8 +1380,16 @@ if(!(status & INT_MASK)) { + + static int count = 10; + if (count) { + count--; + printk("sound status = %08x (mask %08x)\n", + status, INT_MASK); + } + spin_unlock(&card->lock); - return IRQ_NONE; /* not for us */ + return IRQ_RETVAL(status); /* not for us */ } if(status & (INT_PO|INT_PI|INT_MC))
which resulted in:
kernel: Intel 810 + AC97 Audio, version 0.24, 20:51:32 Feb 11 2004
kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
kernel: i810: NVIDIA nForce Audio found at IO 0xd400 and 0xd000, MEM 0x0000 and 0x0000, IRQ 21
kernel: sound status = 00300100 (mask 00000ce7)
last message repeated 9 times
kernel: i810_audio: Audio Controller supports 6 channels.
kernel: i810_audio: Defaulting to base 2 channel mode.
kernel: i810_audio: Resetting connection 0
kernel: ac97_codec: AC97 codec, id: CMI97 (CMedia)
kernel: AC97 codec does not have proper volume support.
kernel: i810_audio: only 48Khz playback available.
kernel: i810_audio: AC'97 codec 0, new EID value = 0x05c6
kernel: i810_audio: AC'97 codec 0, DAC map configured, total channels = 6 /sbin/hotplug[31860]: no runnable /etc/hotplug/sound.agent is installed
kernel: i810_audio: 9472 bytes in 50 milliseconds
kernel: i810_audio: setting clocking to 48648
line in -> line out with xawtv works,
PCM (echo /usr/share/sounds/alsa/test.wav >/dev/dsp) -> does not hang, but no sound
and I get ~250,000 ints/s on IRQ 21
thanks,
Ralf
Signature · 3 lines
P: Linus Torvalds patch-2.2.4 -S: Buried alive in diapers +S: Buried alive in reporters
At 11 Feb 2004 21:11:08 +0100,
Review
Quoted 3 lines · Ralf Gerbig
(quoted diff) +1
-1- return IRQ_NONE; /* not for us */ + return IRQ_RETVAL(status); /* not for us */
after checking the code again, using status as IRQ_RETVAL() isn't a good way, because it has also some static status bits. the attached patch would be better to avoid the confusion. it will return IRQ_HANDLED only when some irq bits are really acknowledged.
Takashi
Index: alsa-kernel/pci/intel8x0.c
===================================================================
RCS file: /suse/tiwai/cvs/alsa/alsa-kernel/pci/intel8x0.c,v retrieving revision 1.115
pci/intel8x0.c +12 -2
@@ -804,10 +804,20 @@spin_lock (&chip->reg_lock); status =igetdword (chip, chip->int_sta_reg);if ((status & chip->int_sta_mask) ==0 ) { -if (status) +static int status_ack =0 ; +static int err_count =10 ; +if (status) {iputdword (chip, chip->int_sta_reg, status); + status_ack =igetdword (chip, chip->int_sta_reg); + }spin_unlock (&chip->reg_lock); -return IRQ_NONE ; + status ^= status_ack; +if (status && err_count) { + err_count--; +snd_printd ("intel8x0: unknown IRQ bits 0x%x (sta_mask=0x%x)\n" , + status, chip->int_sta_mask); + } +return IRQ_RETVAL (status); }for (i =0 ; i < chip->bdbars_count; i++) {
Moins,
Quoted 2 lines · * On Mon, 09 Feb 2004 19:56:48 +0100, Takashi Iwai <[email protected]> said:
could you check the status register value when this happens with the attached patch?
I'm not Lenar, but this is what I get upon module load:
Epox EP8RDA3 Mobo, nforce2, acpi, apic, preempt, 2.6.3-rc1-mm1
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)
21: 751435 IO-APIC-level NVidia nForce2
line in -> line out (bttv) works fine, aplay just plays the first snippet of sound a couple of times and then hangs.
kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
kernel: intel8x0: ignored irq, status = 0x0, sta_mask = 0x0
kernel: intel8x0: ignored irq, status = 0x0, sta_mask = 0x0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2377 times
kernel: intel8x0: ignored irq, status = 0x300100,red irq, status = 0xred irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2146 times
kernel: intel8x0: ignored irq, status = 0x3001red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 1863 times
/sbin/hotplug[5795]: no runnable /etc/hotplug/sound.agent is installed
/sbin/hotplug[5802]: no runnable /etc/hotplug/sound.agent is installed
/sbin/hotplug[5810]: no runnable /etc/hotplug/sound.agent is installed
/sbin/hotplug[5809]: no runnable /etc/hotplug/sound.agent is installed
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 283 times
kernel: red irred irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2146 times
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask =red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 481 times
/sbin/hotplug[5825]: no runnable /etc/hotplug/sound.agent is installed
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 1665 times
kernel: rq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2142 times
kernel: irq 21: nobody cared!
kernel: Call Trace:
kernel: [__report_bad_irq+42/144] __report_bad_irq+0x2a/0x90 kernel: [<c010cc7a>] __report_bad_irq+0x2a/0x90 kernel: [note_interrupt+112/176] note_interrupt+0x70/0xb0 kernel: [<c010cd70>] note_interrupt+0x70/0xb0 kernel: [do_IRQ+304/320] do_IRQ+0x130/0x140 kernel: [<c010d060>] do_IRQ+0x130/0x140 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 kernel: [<c0321d64>] common_interrupt+0x18/0x20
kernel:
kernel: handlers:
kernel: [_end+542335376/1069053776] (snd_intel8x0_interrupt+0x0/0x260 [snd_intel8x0])
kernel: [<e09aba40>] (snd_intel8x0_interrupt+0x0/0x260 [snd_intel8x0])
kernel: Disabling IRQ #21
without hotplug:
kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
kernel: intel8x0: ignored irq, status = 0x0, sta_mask = 0x0
kernel: intel8x0: ignored irq, status = 0x0, sta_mask = 0x0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 939 times
kernel: red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2147 times
kernel: red irq, statured irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2146 times
kernel: intel8x0: ignored irq, status = 0x300100, stred irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2147 times
kernel: red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2147 times
kernel: red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 981 times
kernel: intel8x0: ignored irq, status = 0x300100red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 1163 times
kernel: intel8x0: ignored irq, status = red irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2147 times
kernel: >intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
kernel: intel8x0: ignored irq, status = 0x300100, sta_mask = 0xf0
last message repeated 2134 times
kernel: irq 21: nobody cared! kernel: Call Trace: kernel: [__report_bad_irq+42/144] __report_bad_irq+0x2a/0x90 kernel: [<c010cc7a>] __report_bad_irq+0x2a/0x90 kernel: [note_interrupt+112/176] note_interrupt+0x70/0xb0 kernel: [<c010cd70>] note_interrupt+0x70/0xb0 kernel: [do_IRQ+304/320] do_IRQ+0x130/0x140 kernel: [<c010d060>] do_IRQ+0x130/0x140 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 kernel: [<c0321d64>] common_interrupt+0x18/0x20 kernel: [schedule+884/1456] schedule+0x374/0x5b0 kernel: [<c011dff4>] schedule+0x374/0x5b0 kernel: [preempt_schedule+54/96] preempt_schedule+0x36/0x60 kernel: [<c011e266>] preempt_schedule+0x36/0x60 kernel: [unix_dgram_sendmsg+872/1392] unix_dgram_sendmsg+0x368/0x570 kernel: [<c031c518>] unix_dgram_sendmsg+0x368/0x570 kernel: [call_console_drivers+101/288] call_console_drivers+0x65/0x120 kernel: [<c01221b5>] call_console_drivers+0x65/0x120 kernel: [call_console_drivers+101/288] call_console_drivers+0x65/0x120 kernel: [<c01221b5>] call_console_drivers+0x65/0x120 kernel: [sock_aio_write+191/240] sock_aio_write+0xbf/0xf0 kernel: [<c02b8a3f>] sock_aio_write+0xbf/0xf0 kernel: [do_sync_write+140/192] do_sync_write+0x8c/0xc0 kernel: [<c0157d5c>] do_sync_write+0x8c/0xc0 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 kernel: [<c0321d64>] common_interrupt+0x18/0x20 kernel: [vfs_write+254/304] vfs_write+0xfe/0x130 kernel: [<c0157e8e>] vfs_write+0xfe/0x130 kernel: [sys_write+66/112] sys_write+0x42/0x70 kernel: [<c0157f72>] sys_write+0x42/0x70 kernel: [syscall_call+7/11] syscall_call+0x7/0xb kernel: [<c03213f7>] syscall_call+0x7/0xb
kernel:
kernel: handlers:
kernel: [_end+542335376/1069053776] (snd_intel8x0_interrupt+0x0/0x260 [snd_intel8x0])
kernel: [<e09aba40>] (snd_intel8x0_interrupt+0x0/0x260 [snd_intel8x0])
kernel: Disabling IRQ #21
hope this helps,
Ralf
Signature · 3 lines
P: Linus Torvalds patch-2.2.4 -S: Buried alive in diapers +S: Buried alive in reporters