Skip to contentSkip to conversation

drm/rockchip: vop2: RK3588 clocking, sync polarity, AXI port and window fixes

PATCH Superseded Arun Iyengar 3 participants 18 messages Nov 10

Subsystems (4)

v1 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

cover drm/rockchip: vop2: RK3588 clocking, sync polarity, AXI port and window fixes

This series collects fixes for the RK3588 VOP2 found while bringing up HDMI and DisplayPort output on an Orange Pi 5 (RK3588S).

Patches 1 and 2 fix the RK3588 interface setup: rk3588_calc_cru_cfg() leaves dividers it does not use uninitialised and the garbage ends up in VP_CLK_CTRL, and rk3588_get_hdmi_pol() decodes the POLFLAG bits it is handed as DRM mode flags, so the GRF sync polarity bits are wrong for most modes.

Patch 3 stops the RK3588 Cluster windows from advertising AFBC with the lossless colour transform (YTR) for RGB565/BGR565, which the decoder cannot display (black picture plus POST_BUF_EMPTY).

Patches 4 and 5 deal with POST_BUF_EMPTY underflows. The VOP2 fetches through two AXI read ports but the port of each window is fixed in the window table, so the usual primary plane plus overlay configuration of a video port puts both layers on one port while the other sits idle. One port cannot sustain two full screen 4K@120Hz layers (measured: the fetch rate collapses from ~6 GB/s to ~3 GB/s and about half of all lines underflow). Patch 4 assigns the port when a window starts fetching, balancing the estimated load; patch 5 rate-limits the POST_BUF_EMPTY interrupt to once per frame, since an underflowing port otherwise keeps the CPU in the interrupt handler 50000 to 300000 times per second.

Patches 6 to 8 are smaller fixes: the start mixer search skipped Esmart3 (for_each_set_bit() was given the highest window id as the bit count), a gamma LUT update cleared the other fields of LUT_PORT_SEL (the VP0/VP2 dclk source selection and the VP0/VP1 merge enable), and the AFBC tile count and transform offset were wrong for a source that starts inside a 16 pixel superblock.

Tested on an Orange Pi 5 (RK3588S) with an HDMI 2.1 TV and a DisplayPort monitor, pictures judged with a camera. Patches 1 and 2:
VP0_CLK_CTRL reads back without the garbage dclk_out divider, the sync polarities seen by the HDMI controller (VIDEO_INTERFACE_STATUS0) match the mode flags for +/+ (1080p, 2160p) and -/- (720x480, 640x480) modes, and the picture is correct over TMDS and FRL modes from 27 to 1188 MHz. Patch 3: RGB565 is offered on the Cluster windows only without YTR, and those planes scan out correctly on three Cluster windows. Patches 4 and 5: 3840x2160@120 with a full screen overlay (previously ~120000 POST_BUF_EMPTY per second and a scrambled picture) and a dual-display session (HDMI 4K@60 plus DP 4K@30, two video players, ten minutes) run with zero underflows. Patches 6 to 8 were found while driving Esmart3 and partial AFBC overlays: an AFBC overlay placed at x=1001 shows correctly. All eight have been in the board's kernel for the display test runs since.

This series was developed with Claude (Anthropic) as a coding assistant:
it wrote the code and the commit messages, and I reviewed and tested every change as described above.

---
Arun Iyengar (8):
drm/rockchip: vop2: Don't use uninitialised dividers on RK3588 drm/rockchip: vop2: Fix the HDMI sync polarity on RK3588 drm/rockchip: vop2: Don't accept AFBC YTR for RGB565 on RK3588 drm/rockchip: vop2: Balance window fetches across both AXI ports on RK3588 drm/rockchip: vop2: Report POST_BUF_EMPTY at most once per frame drm/rockchip: vop2: Find the first mixer of a video port with Esmart3 too drm/rockchip: vop2: Keep the other LUT_PORT_SEL fields on gamma LUT updates drm/rockchip: vop2: Fix the AFBC offsets of a source that starts inside a superblock

 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 186 +++++++++++++++++++++++++--
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.h |  24 ++++
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c |  27 +++-
 3 files changed, 223 insertions(+), 14 deletions(-)

---
base-commit: 8deaade4a5a4ff635df91e246e42139ab2b33f6d
change-id: 20261110-vop2-fixes-fa45142799c1

Best regards,

Signature · 1 line
Arun Iyengar <[email protected]>
#1 lore raw

PATCH 1/8 drm/rockchip: vop2: Don't use uninitialised dividers on RK3588

rk3588_calc_cru_cfg() converts all four dividers to their register encoding with ilog2(), but only sets the ones the interface uses:
dclk_out_div is left uninitialised for HDMI, eDP and DPI, and if_pixclk_div/if_dclk_div for DP and DPI. The garbage is then written to RK3588_VP_CLK_CTRL; on an Orange Pi 5 the dclk_out divider of the HDMI video port reads back as 3 (/8) in every mode.

Start all dividers at 1. dclk_out only feeds DP and MIPI (and HDMI with DSC, which is not supported), so for the other interfaces keep it at the dclk_core rate, as the vendor kernel does for HDMI with DSC, instead of letting it run at the full DCLK rate.

Fixes 5a028e8f062f ("drm/rockchip: vop2: Add support for rk3588")
---
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +12 -0
index c44648e1bc0d..659fd0a3ab63 100644
@@ -1579,6 +1579,15 @@ static unsigned long rk3588_calc_cru_cfg(struct vop2_video_port *vp, int id,
 	unsigned long if_pixclk_rate;
 	int K = 1;
 
+	/*
+	 * Not every interface uses every divider: dclk_out only feeds DP and
+	 * MIPI, the interface dividers are unused for DP. Start from 1 so that
+	 * no divider is left uninitialised when its value is converted below.
+	 */
+	*dclk_out_div = 1;
+	*if_pixclk_div = 1;
+	*if_dclk_div = 1;
+
 	if (vop2_output_if_is_hdmi(id)) {
 		/*
 		 * K = 2: dclk_core = if_pixclk_rate > if_dclk_rate
@@ -1648,6 +1657,9 @@ static unsigned long rk3588_calc_cru_cfg(struct vop2_video_port *vp, int id,
 	}
 
 	*dclk_core_div = dclk_rate / dclk_core_rate;
+	/* An unused dclk_out must not run faster than dclk_core */
+	if (!vop2_output_if_is_dp(id) && !vop2_output_if_is_mipi(id))
+		*dclk_out_div = *dclk_core_div;
 	*if_pixclk_div = ilog2(*if_pixclk_div);
 	*if_dclk_div = ilog2(*if_dclk_div);
 	*dclk_core_div = ilog2(*dclk_core_div);
Signature · 1 line
2.55.0
#2 lore raw

PATCH 2/8 drm/rockchip: vop2: Fix the HDMI sync polarity on RK3588

In reply to Arun Iyengar

rk3588_set_intf_mux() passes the POLFLAG bits of the mode to rk3588_get_hdmi_pol(), which decodes them as DRM mode flags: the VSYNC_POSITIVE bit is taken for DRM_MODE_FLAG_NHSYNC and POLFLAG_DCLK_INV for DRM_MODE_FLAG_NVSYNC. As a result GRF_VO1_CON0 marks the HSYNC of every +HSync/+VSync mode (e.g. all 1080p, 2160p CTA modes) as negative and both syncs of -HSync/-VSync modes (e.g. 720x480, 640x480) as positive.

The bits in GRF_VO1_CON0 are set for a negative sync; that is how the vendor kernel programs them (vop2_get_hdmi_pol(), called with the mode flags, sets them for DRM_MODE_FLAG_NHSYNC/NVSYNC on RK3588). Decode the POLFLAG bits accordingly.

Fixes 5a028e8f062f ("drm/rockchip: vop2: Add support for rk3588")
---
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +7 -3
index 659fd0a3ab63..7c48b440cb29 100644
@@ -1687,12 +1687,16 @@ static u32 rk3588_get_mipi_port_mux(int vp_id)
 		return 0;
 }
 
-static u32 rk3588_get_hdmi_pol(u32 flags)
+/*
+ * The HDMI sync polarity bits in GRF_VO1_CON0 are set for an active low
+ * (negative) sync.
+ */
+static u32 rk3588_get_hdmi_pol(u32 polflags)
 {
 	u32 val;
 
-	val = (flags & DRM_MODE_FLAG_NHSYNC) ? BIT(HSYNC_POSITIVE) : 0;
-	val |= (flags & DRM_MODE_FLAG_NVSYNC) ? BIT(VSYNC_POSITIVE) : 0;
+	val = (polflags & BIT(HSYNC_POSITIVE)) ? 0 : BIT(HSYNC_POSITIVE);
+	val |= (polflags & BIT(VSYNC_POSITIVE)) ? 0 : BIT(VSYNC_POSITIVE);
 
 	return val;
 }
Signature · 1 line
2.55.0
#3 lore raw

PATCH 3/8 drm/rockchip: vop2: Don't accept AFBC YTR for RGB565 on RK3588

In reply to Arun Iyengar

The Cluster windows of the RK3588 VOP2 advertise every AFBC modifier of format_modifiers_afbc for RGB565 and BGR565, including the ones with the lossless colour transform (YTR). Scanning out an RGB565 buffer rendered by the Mali-G610 (panfrost) with AFBC(16x16 | SPARSE | YTR) gives a black picture and POST_BUF_EMPTY on the video port, on every Cluster window, while the same buffer rendered with AFBC(16x16 | SPARSE) displays correctly, as do 32 bpp formats with YTR.

YTR on RGB565 is also a questionable pairing to start with:
Documentation/gpu/afbc.rst requires the R, G, B component order when YTR is used, with component 0 in the least significant bits, which DRM_FORMAT_RGB565 (B in the low bits) doesn't have, and the Arm Mali-D71 (komeda) only accepts AFBC for BGR565.

Stop advertising and accepting YTR for the two 16 bpp RGB formats on RK3588, so that userspace picks a modifier the decoder handles. The BGR565 case could not be tested (Mesa can't import BGR565 dma-bufs), it's rejected as well because the decoder is configured identically for both formats, apart from the R/B swap after decoding.

Fixes 5a028e8f062f ("drm/rockchip: vop2: Add support for rk3588")
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +12 -0
index 76d151b8bc52..629ea7f11250 100644
@@ -404,6 +404,18 @@ static bool rockchip_vop2_mod_supported(struct drm_plane *plane, u32 format,
 	if (vop2_convert_afbc_format(format) == VOP2_AFBC_FMT_INVALID)
 		return false;
 
+	/*
+	 * The AFBC decoder of the RK3588 Cluster windows can't decode 16 bpp
+	 * RGB that uses the lossless colour transform: the picture stays
+	 * black and the video port reports POST_BUF_EMPTY, while the same
+	 * buffers without YTR display fine.
+	 */
+	if (vop2->version == VOP_VERSION_RK3588 && (modifier & AFBC_FORMAT_MOD_YTR) &&
+	    (format == DRM_FORMAT_RGB565 || format == DRM_FORMAT_BGR565)) {
+		drm_dbg_kms(vop2->drm, "No AFBC YTR support for 16 bpp RGB\n");
+		return false;
+	}
+
 	/* Different windows have different format/modifier support */
 	for (i = 0; i < plane->modifier_count; i++) {
 		if (plane->modifiers[i] == modifier)
Signature · 1 line
2.55.0
#4 lore raw

PATCH 4/8 drm/rockchip: vop2: Balance window fetches across both AXI ports on RK3588

In reply to Arun Iyengar

The RK3588 VOP2 fetches through two AXI read ports. Every window has a fixed default port in rk3588_vop_win_data: Cluster0/1 and Esmart0/1 use AXI0, Cluster2/3 and Esmart2/3 use AXI1. The port is chosen by a per window register (CLUSTER_CTRL[13] / ESMART_AXI_CTRL[1]), though, and it is programmed on every plane update.

One port can't sustain two full screen 4K@120Hz layers. With the console on Cluster0 (the primary plane of video port 0) and a video on Esmart0 (its overlay plane), both on AXI0, HDMI 3840x2160@120 reports POST_BUF_EMPTY on about half of all lines (~120000 per second) and the picture is scrambled. The VOP read rate measured with the DDR PMU drops from the expected 6.3 GB/s to 3.2 GB/s: the fetch collapses instead of merely saturating. Measured at 4K@120Hz, XR24 primary plane:

Cluster0 + Esmart0 (AXI0 + AXI0) ~120k POST_BUF_EMPTY/s
Cluster2 + Esmart2 (AXI1 + AXI1) ~100k/s
Esmart0 + Esmart1 (AXI0 + AXI0) ~90k/s (XR24 both)
Cluster0 + Esmart2 (AXI0 + AXI1) 0, 9.2 GB/s read
Cluster0 + Cluster2 (AXI0 + AXI1) 0, 8.6 GB/s read

Moving Esmart0 to AXI1 at runtime (with no other change) makes the first case clean. Raising ACLK_VOP from 750 to 850 MHz, or changing the NoC QoS priority or mode of the VOP ports, makes no difference, and neither does the buffer placement (both planes scanning out the same buffer fail the same way). So the limit is per port, and the fixed assignment puts both layers of the most common configuration on the same port while the other one sits idle. Lower modes are affected
too: the same port also carries Cluster1 for a second display, and under DDR contention from other masters a 4K@60Hz port with the console, an overlay and a second display underflows for short bursts.

Choose the port of a window when it starts fetching instead: estimate the fetch rate of each active window (source size x bpp x refresh), and put the new window on the port that leaves the busier port least loaded, preferring the default one on a tie. A window must not share an AXI read ID with another active window on the same port; the IDs in the table are unique per default port, and mirrored between the two ports (Cluster0/Cluster2, Esmart0/Esmart2, ...), so a window can always use the port its mirror isn't on. A window keeps its port while it stays enabled, so an active layer is never moved.

This is only enabled for RK3588, where it was measured.

---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 99 +++++++++++++++++++++++++++-
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.h | 14 ++++
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c |  3 +-
 3 files changed, 114 insertions(+), 2 deletions(-)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +98 -1
index 629ea7f11250..9aeb90c6aa4b 100644
@@ -1231,6 +1231,98 @@ static int vop2_plane_atomic_check(struct drm_plane *plane,
 	return 0;
 }
 
+static bool vop2_win_axi_ids_clash(const struct vop2_win *a, const struct vop2_win *b)
+{
+	u8 ida[] = { a->data->axi_yrgb_r_id, a->data->axi_uv_r_id };
+	u8 idb[] = { b->data->axi_yrgb_r_id, b->data->axi_uv_r_id };
+	int i, j;
+
+	for (i = 0; i < ARRAY_SIZE(ida); i++)
+		for (j = 0; j < ARRAY_SIZE(idb); j++)
+			if (ida[i] == idb[j])
+				return true;
+
+	return false;
+}
+
+/*
+ * The VOP2 on RK3588 has two AXI read ports. Each window has a default port
+ * (&vop2_win_data.axi_bus_id), but the port is selected by a per window
+ * register, so any window can fetch through either one as long as its read
+ * IDs are unique on that port.
+ *
+ * A single port can't sustain much more than one full screen 4K@120Hz
+ * layer: two such layers on the same port (e.g. Cluster0 and Esmart0, the
+ * default primary and overlay planes of video port 0) make the window
+ * line buffers run dry, the fetch rate collapses and the video port
+ * reports POST_BUF_EMPTY on most lines, which scrambles the picture. The
+ * same layers fetched through different ports are fine. Raising ACLK or
+ * the NoC priority of the VOP doesn't help, the limit is per port.
+ *
+ * So pick the port of a window when it starts fetching: use the port that
+ * leaves the busier of the two ports least loaded, preferring the default
+ * one, and never a port on which another active window already uses one of
+ * its read IDs. A window keeps its port while it stays enabled.
+ */
+static u8 vop2_win_get_axi_bus(struct vop2_win *win, u64 load)
+{
+	struct vop2 *vop2 = win->vop2;
+	u64 bus_load[VOP2_SYS_AXI_BUS_NUM] = { };
+	bool clash[VOP2_SYS_AXI_BUS_NUM] = { };
+	u8 def = win->data->axi_bus_id;
+	unsigned long flags;
+	u8 bus = def;
+	int i;
+
+	if (!(vop2->data->feature & VOP2_FEATURE_AXI_BALANCE))
+		return def;
+
+	spin_lock_irqsave(&vop2->axi_lock, flags);
+
+	if (win->axi_active) {
+		win->axi_load = load;
+		bus = win->axi_bus;
+		goto out;
+	}
+
+	for (i = 0; i < vop2->registered_num_wins; i++) {
+		struct vop2_win *w = &vop2->win[i];
+
+		if (w == win || !w->axi_active)
+			continue;
+
+		bus_load[w->axi_bus] += w->axi_load;
+		if (vop2_win_axi_ids_clash(win, w))
+			clash[w->axi_bus] = true;
+	}
+
+	if (!clash[def ^ 1] &&
+	    (clash[def] || max(bus_load[def ^ 1] + load, bus_load[def]) <
+			   max(bus_load[def] + load, bus_load[def ^ 1])))
+		bus = def ^ 1;
+
+	WARN_ON_ONCE(clash[bus]);
+
+	win->axi_bus = bus;
+	win->axi_load = load;
+	win->axi_active = true;
+out:
+	spin_unlock_irqrestore(&vop2->axi_lock, flags);
+
+	return bus;
+}
+
+static void vop2_win_put_axi_bus(struct vop2_win *win)
+{
+	struct vop2 *vop2 = win->vop2;
+	unsigned long flags;
+
+	spin_lock_irqsave(&vop2->axi_lock, flags);
+	win->axi_active = false;
+	win->axi_load = 0;
+	spin_unlock_irqrestore(&vop2->axi_lock, flags);
+}
+
 static void vop2_plane_atomic_disable(struct drm_plane *plane,
 				      struct drm_atomic_commit *state)
 {
@@ -1241,6 +1333,8 @@ static void vop2_plane_atomic_disable(struct drm_plane *plane,
 
 	drm_dbg(vop2->drm, "%s disable\n", win->data->name);
 
+	vop2_win_put_axi_bus(win);
+
 	if (state)
 		old_pstate = drm_atomic_get_old_plane_state(state, plane);
 
@@ -1416,7 +1510,9 @@ static void vop2_plane_atomic_update(struct drm_plane *plane,
 		afbc_en ? "AFBC" : "", &yrgb_mst);
 
 	if (vop2->version > VOP_VERSION_RK3568) {
-		vop2_win_write(win, VOP2_WIN_AXI_BUS_ID, win->data->axi_bus_id);
+		u64 load = (u64)src_w * src_h * bpp / 8 * drm_mode_vrefresh(adjusted_mode);
+
+		vop2_win_write(win, VOP2_WIN_AXI_BUS_ID, vop2_win_get_axi_bus(win, load));
 		vop2_win_write(win, VOP2_WIN_AXI_YRGB_R_ID, win->data->axi_yrgb_r_id);
 		vop2_win_write(win, VOP2_WIN_AXI_UV_R_ID, win->data->axi_uv_r_id);
 	}
@@ -3005,6 +3101,7 @@ static int vop2_bind(struct device *dev, struct device *master, void *data)
 
 	mutex_init(&vop2->vop2_lock);
 	mutex_init(&vop2->ovl_lock);
+	spin_lock_init(&vop2->axi_lock);
 
 	ret = devm_request_irq(dev, vop2->irq, vop2_isr, IRQF_SHARED, dev_name(dev), vop2);
 	if (ret)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.h +14 -0
index 1c2d7d97a6c2..f1e35967e67f 100644
@@ -29,6 +29,7 @@
 #define VOP2_FEATURE_HAS_VO1_GRF	BIT(2)
 #define VOP2_FEATURE_HAS_VOP_GRF	BIT(3)
 #define VOP2_FEATURE_HAS_SYS_PMU	BIT(4)
+#define VOP2_FEATURE_AXI_BALANCE	BIT(5)
 
 #define WIN_FEATURE_AFBDC		BIT(0)
 #define WIN_FEATURE_CLUSTER		BIT(1)
@@ -219,6 +220,16 @@ struct vop2_win {
 	u32 offset;
 
 	enum drm_plane_type type;
+
+	/**
+	 * @axi_bus: AXI read port the window currently fetches through,
+	 * protected by &vop2.axi_lock.
+	 */
+	u8 axi_bus;
+	/** @axi_active: the window is fetching, protected by &vop2.axi_lock */
+	bool axi_active;
+	/** @axi_load: estimated fetch rate in bytes/s, protected by &vop2.axi_lock */
+	u64 axi_load;
 };
 
 struct vop2_video_port_data {
@@ -356,6 +367,9 @@ struct vop2 {
 	 */
 	struct mutex ovl_lock;
 
+	/* protects the AXI port assignment of all windows (&vop2_win.axi_bus) */
+	spinlock_t axi_lock;
+
 	/* must be put at the end of the struct */
 	struct vop2_win win[];
 };
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +2 -1
index 7c48b440cb29..83203d18865b 100644
@@ -2577,7 +2577,8 @@ static const struct vop2_data rk3576_vop = {
 static const struct vop2_data rk3588_vop = {
 	.version = VOP_VERSION_RK3588,
 	.feature = VOP2_FEATURE_HAS_SYS_GRF | VOP2_FEATURE_HAS_VO1_GRF |
-		   VOP2_FEATURE_HAS_VOP_GRF | VOP2_FEATURE_HAS_SYS_PMU,
+		   VOP2_FEATURE_HAS_VOP_GRF | VOP2_FEATURE_HAS_SYS_PMU |
+		   VOP2_FEATURE_AXI_BALANCE,
 	.nr_vps = 4,
 	.max_input = { 4096, 4320 },
 	.max_output = { 4096, 4320 },
Signature · 1 line
2.55.0
#5 lore raw

Re: [PATCH 4/8] drm/rockchip: vop2: Balance window fetches across both AXI ports on RK3588

Thank you for your contribution! Sashiko AI review found 3 potential issues to consider: - [Medium] drm/rockchip: vop2: plane commit order skews vop2_win_get_axi_bus() - [Medium] drm/rockchip: vop2…

Thank you for your contribution! Sashiko AI review found 3 potential issues to consider:
- [Medium] drm/rockchip: vop2: plane commit order skews vop2_win_get_axi_bus()
- [Medium] drm/rockchip: vop2: vop2_plane_atomic_update() omits UV plane AXI load
- [Medium] drm/rockchip: vop2: premature AXI bus release in vop2_win_put_axi_bus()
It also noticed 1 related pre-existing issue this patch does not introduce:
- [High] drm/rockchip: vop2: wrong GEM object for UV plane in vop2_plane_atomic_update() [1]
--

commit d091a328bc345e54d430e0882d6dfc1be033a2f5
Author: Arun Iyengar <[email protected]>

drm/rockchip: vop2: Balance window fetches across both AXI ports on RK3588

This commit dynamically assigns newly enabled VOP2 windows on RK3588 to the least loaded of the two AXI read ports while avoiding AXI read ID collisions with other active windows.

Quoted 5 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +0 -0
index 629ea7f112502..9aeb90c6aa4b1 100644
@@ -1231,6 +1231,98 @@ static int vop2_plane_atomic_check(struct drm_plane *plane,

[ ... ]

Quoted 37 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +37 -0
+static u8 vop2_win_get_axi_bus(struct vop2_win *win, u64 load)
+{
+	struct vop2 *vop2 = win->vop2;
+	u64 bus_load[VOP2_SYS_AXI_BUS_NUM] = { };
+	bool clash[VOP2_SYS_AXI_BUS_NUM] = { };
+	u8 def = win->data->axi_bus_id;
+	unsigned long flags;
+	u8 bus = def;
+	int i;
+
+	if (!(vop2->data->feature & VOP2_FEATURE_AXI_BALANCE))
+		return def;
+
+	spin_lock_irqsave(&vop2->axi_lock, flags);
+
+	if (win->axi_active) {
+		win->axi_load = load;
+		bus = win->axi_bus;
+		goto out;
+	}
+
+	for (i = 0; i < vop2->registered_num_wins; i++) {
+		struct vop2_win *w = &vop2->win[i];
+
+		if (w == win || !w->axi_active)
+			continue;
+
+		bus_load[w->axi_bus] += w->axi_load;
+		if (vop2_win_axi_ids_clash(win, w))
+			clash[w->axi_bus] = true;
+	}
+
+	if (!clash[def ^ 1] &&
+	    (clash[def] || max(bus_load[def ^ 1] + load, bus_load[def]) <
+			   max(bus_load[def] + load, bus_load[def ^ 1])))
+		bus = def ^ 1;
+

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static int vop2_plane_atomic_check(struct drm_plane *plane, · line 1313

Quoted 10 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +10 -0
+	WARN_ON_ONCE(clash[bus]);
+
+	win->axi_bus = bus;
+	win->axi_load = load;
+	win->axi_active = true;
+out:
+	spin_unlock_irqrestore(&vop2->axi_lock, flags);
+
+	return bus;
+}

[Severity: Medium]
Does vop2_win_get_axi_bus() see stale axi_active and axi_load state for higher-indexed planes changed in the same atomic commit?

drm_atomic_helper_commit_planes() runs a single loop in ascending plane index order, calling atomic_disable() or atomic_update() on each plane. In rk3588_vop_win_data, all windows that default to AXI0 (Cluster0/1, Esmart0/1) have lower indices than their AXI1 mirrors (Cluster2/3, Esmart2/3). When a commit enables Esmart0 while disabling Esmart2 (or another higher-indexed plane on AXI1), vop2_win_get_axi_bus() runs for Esmart0 before vop2_plane_atomic_disable() clears Esmart2's axi_active. It therefore sees Esmart2's old load and read-ID clash on AXI1 and pins Esmart0 to AXI0 alongside Cluster0 for as long as Esmart0 remains enabled, causing the POST_BUF_EMPTY underflows this patch aims to avoid.

Quoted 16 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +12 -0
+
+static void vop2_win_put_axi_bus(struct vop2_win *win)
+{
+	struct vop2 *vop2 = win->vop2;
+	unsigned long flags;
+
+	spin_lock_irqsave(&vop2->axi_lock, flags);
+	win->axi_active = false;
+	win->axi_load = 0;
+	spin_unlock_irqrestore(&vop2->axi_lock, flags);
+}
+
 static void vop2_plane_atomic_disable(struct drm_plane *plane,
 				      struct drm_atomic_commit *state)
 {

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static void vop2_plane_atomic_disable(struct drm_plane *plane, · line 1339

Quoted 7 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +2 -0
@@ -1241,6 +1333,8 @@ static void vop2_plane_atomic_disable(struct drm_plane *plane,
 
 	drm_dbg(vop2->drm, "%s disable\n", win->data->name);
 
+	vop2_win_put_axi_bus(win);
+
 	if (state)
 		old_pstate = drm_atomic_get_old_plane_state(state, plane);

[Severity: Medium]
Can clearing win->axi_active in vop2_plane_atomic_disable() cause an AXI read ID collision before the disable is latched at VSYNC?

VOP2_WIN_ENABLE is a shadow register latched at the video port's next VSYNC, so the disabled window keeps fetching over win->axi_bus until then. If Esmart0 is on AXI1 on VP0 and is disabled while its mirror Esmart2 (which shares read IDs 0x0a and 0x0b) is enabled on VP1, vop2_win_get_axi_bus() sees Esmart0->axi_active == false and assigns Esmart2 to AXI1. If VP1's VSYNC fires before VP0's VSYNC, both windows fetch on AXI1 with identical read IDs until VP0 latches the disable.

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static void vop2_plane_atomic_update(struct drm_plane *plane, · line 1518

Quoted 11 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +3 -1
@@ -1416,7 +1510,9 @@ static void vop2_plane_atomic_update(struct drm_plane *plane,
 		afbc_en ? "AFBC" : "", &yrgb_mst);
 
 	if (vop2->version > VOP_VERSION_RK3568) {
-		vop2_win_write(win, VOP2_WIN_AXI_BUS_ID, win->data->axi_bus_id);
+		u64 load = (u64)src_w * src_h * bpp / 8 * drm_mode_vrefresh(adjusted_mode);
+
+		vop2_win_write(win, VOP2_WIN_AXI_BUS_ID, vop2_win_get_axi_bus(win, load));
 		vop2_win_write(win, VOP2_WIN_AXI_YRGB_R_ID, win->data->axi_yrgb_r_id);
 		vop2_win_write(win, VOP2_WIN_AXI_UV_R_ID, win->data->axi_uv_r_id);
 	}

[Severity: Medium]
Does computing load from bpp omit the UV plane bandwidth for multi-planar YUV formats?

bpp comes from vop2_get_bpp(fb->format), which falls back to drm_format_info_bpp(format, 0) and returns only plane 0's bits per pixel:

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:vop2_get_bpp() {
	switch (format->format) {
	case DRM_FORMAT_YUV420_8BIT:
		return 12;
	case DRM_FORMAT_YUV420_10BIT:
		return 15;
	case DRM_FORMAT_VUY101010:
		return 30;
	default:
		return drm_format_info_bpp(format, 0);
	}
}

For semi-planar formats such as NV12, NV16 or NV24, plane 1 is fetched through the same AXI port via VOP2_WIN_AXI_UV_R_ID, but bpp only counts the Y plane (8 or 10 bpp instead of 12 to 30 bpp), underestimating win->axi_load by 33% to 67%.

[Severity: High]
This problem wasn't introduced by this patch, but earlier in vop2_plane_atomic_update() the UV plane DMA address is computed from fb->obj[0] instead of fb->obj[1] [1]:

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:vop2_plane_atomic_update() {
	...
	rk_obj = to_rockchip_obj(fb->obj[0]);

	yrgb_mst = rk_obj->dma_addr + offset + fb->offsets[0];
	if (fb->format->is_yuv) {
		...
		rk_obj = to_rockchip_obj(fb->obj[0]);
		uv_mst = rk_obj->dma_addr + offset + fb->offsets[1];
	}
}

When a multi-planar YUV framebuffer has separate GEM objects for the Y and UV planes, VOP2_WIN_UV_MST is programmed with plane 0's DMA base address plus plane 1's offset, causing corrupted scanout or out-of-bounds DMA reads past fb->obj[0].

[1] https://sashiko.dev/#/bug/linux-46433ab8-0e41-4994-af45-5dfb41ba7894

Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=4
#6 lore raw

PATCH 5/8 drm/rockchip: vop2: Report POST_BUF_EMPTY at most once per frame

In reply to Arun Iyengar

POST_BUF_EMPTY is raised for every line on which the post processing stage of a video port finds no data. The interrupt handler only rate-limits the error message and leaves the interrupt enabled, so an underflowing video port keeps the CPU in the interrupt handler 50000 to 300000 times per second, for as long as the configuration that causes the underflow stays in place (e.g. 120000 interrupts per second for 3840x2160@120 with two full screen layers on one AXI port).

Mask POST_BUF_EMPTY when it fires and unmask it at the next frame start. The frame start (FS) interrupt is enabled for that frame even when vblank reporting is off, and disabled again once POST_BUF_EMPTY is re-armed. A new per video port lock serialises the interrupt enable bookkeeping between the interrupt handler and the vblank callbacks. The error is still reported, now at most once per frame and video port.

---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 63 ++++++++++++++++++++++++++--
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.h | 10 +++++
 2 files changed, 70 insertions(+), 3 deletions(-)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +60 -3
index 9aeb90c6aa4b..3323e50224c5 100644
@@ -841,6 +841,48 @@ static void vop2_crtc_disable_irq(struct vop2_video_port *vp, u32 irq)
 	vop2_writel(vop2, RK3568_VP_INT_EN(vp->id), irq << 16);
 }
 
+/*
+ * POST_BUF_EMPTY is raised for every line the post processing stage finds
+ * no data for, so an underflowing video port can raise it 100000 times per
+ * second. Report it at most once per frame: mask it when it fires and
+ * unmask it at the next frame start, using the FS interrupt even when
+ * vblank reporting is off.
+ */
+static void vop2_crtc_enable_post_buf_empty_irq(struct vop2_video_port *vp)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->post_buf_empty_masked = false;
+	vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
+}
+
+static void vop2_crtc_handle_post_buf_empty(struct vop2_video_port *vp)
+{
+	struct vop2 *vop2 = vp->vop2;
+
+	spin_lock(&vp->irq_lock);
+	vop2_crtc_disable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	vp->post_buf_empty_masked = true;
+	/* don't clear a pending FS, it may carry a vblank event */
+	vop2_writel(vop2, RK3568_VP_INT_EN(vp->id),
+		    VP_INT_FS_FIELD << 16 | VP_INT_FS_FIELD);
+	spin_unlock(&vp->irq_lock);
+}
+
+static void vop2_crtc_rearm_post_buf_empty(struct vop2_video_port *vp)
+{
+	spin_lock(&vp->irq_lock);
+	if (vp->post_buf_empty_masked) {
+		vp->post_buf_empty_masked = false;
+		vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+		if (!vp->vblank_enabled)
+			vop2_crtc_disable_irq(vp, VP_INT_FS_FIELD);
+	}
+	spin_unlock(&vp->irq_lock);
+}
+
 static int vop2_core_clks_prepare_enable(struct vop2 *vop2)
 {
 	int ret;
@@ -1668,8 +1710,12 @@ static const struct drm_plane_funcs vop2_plane_funcs = {
 static int vop2_crtc_enable_vblank(struct drm_crtc *crtc)
 {
 	struct vop2_video_port *vp = to_vop2_video_port(crtc);
+	unsigned long flags;
 
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->vblank_enabled = true;
 	vop2_crtc_enable_irq(vp, VP_INT_FS_FIELD);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
 
 	return 0;
 }
@@ -1677,8 +1723,13 @@ static int vop2_crtc_enable_vblank(struct drm_crtc *crtc)
 static void vop2_crtc_disable_vblank(struct drm_crtc *crtc)
 {
 	struct vop2_video_port *vp = to_vop2_video_port(crtc);
+	unsigned long flags;
 
-	vop2_crtc_disable_irq(vp, VP_INT_FS_FIELD);
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->vblank_enabled = false;
+	if (!vp->post_buf_empty_masked)
+		vop2_crtc_disable_irq(vp, VP_INT_FS_FIELD);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
 }
 
 static enum drm_mode_status vop2_crtc_mode_valid(struct drm_crtc *crtc,
@@ -1977,7 +2028,7 @@ static void vop2_crtc_atomic_enable(struct drm_crtc *crtc,
 
 	vcstate->yuv_overlay = is_yuv_output(vcstate->bus_format);
 
-	vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	vop2_crtc_enable_post_buf_empty_irq(vp);
 
 	polflags = 0;
 	if (vcstate->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
@@ -2535,6 +2586,7 @@ static irqreturn_t rk3576_vp_isr(int irq, void *data)
 	}
 
 	if (irqs & VP_INT_FS_FIELD) {
+		vop2_crtc_rearm_post_buf_empty(vp);
 		drm_crtc_handle_vblank(crtc);
 		spin_lock(&crtc->dev->event_lock);
 		if (vp->event) {
@@ -2552,6 +2604,7 @@ static irqreturn_t rk3576_vp_isr(int irq, void *data)
 	}
 
 	if (irqs & VP_INT_POST_BUF_EMPTY) {
+		vop2_crtc_handle_post_buf_empty(vp);
 		drm_err_ratelimited(vop2->drm, "POST_BUF_EMPTY irq err at vp%d\n", vp->id);
 		ret = IRQ_HANDLED;
 	}
@@ -2591,6 +2644,7 @@ static irqreturn_t vop2_isr(int irq, void *data)
 			}
 
 			if (irqs & VP_INT_FS_FIELD) {
+				vop2_crtc_rearm_post_buf_empty(vp);
 				drm_crtc_handle_vblank(crtc);
 				spin_lock(&crtc->dev->event_lock);
 				if (vp->event) {
@@ -2608,6 +2662,7 @@ static irqreturn_t vop2_isr(int irq, void *data)
 			}
 
 			if (irqs & VP_INT_POST_BUF_EMPTY) {
+				vop2_crtc_handle_post_buf_empty(vp);
 				drm_err_ratelimited(vop2->drm,
 						    "POST_BUF_EMPTY irq err at vp%d\n",
 						    vp->id);
@@ -2984,7 +3039,7 @@ static int vop2_bind(struct device *dev, struct device *master, void *data)
 	struct vop2 *vop2;
 	struct resource *res;
 	size_t alloc_size;
-	int ret;
+	int ret, i;
 
 	vop2_data = of_device_get_match_data(dev);
 	if (!vop2_data)
@@ -3102,6 +3157,8 @@ static int vop2_bind(struct device *dev, struct device *master, void *data)
 	mutex_init(&vop2->vop2_lock);
 	mutex_init(&vop2->ovl_lock);
 	spin_lock_init(&vop2->axi_lock);
+	for (i = 0; i < ARRAY_SIZE(vop2->vps); i++)
+		spin_lock_init(&vop2->vps[i].irq_lock);
 
 	ret = devm_request_irq(dev, vop2->irq, vop2_isr, IRQF_SHARED, dev_name(dev), vop2);
 	if (ret)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.h +10 -0
index f1e35967e67f..7de32bef8d7b 100644
@@ -272,6 +272,16 @@ struct vop2_video_port {
 	struct drm_pending_vblank_event *event;
 
 	unsigned int nlayers;
+
+	/** @irq_lock: protects @vblank_enabled and @post_buf_empty_masked */
+	spinlock_t irq_lock;
+	/** @vblank_enabled: the FS interrupt is enabled for vblank reporting */
+	bool vblank_enabled;
+	/**
+	 * @post_buf_empty_masked: POST_BUF_EMPTY is masked until the next
+	 * frame start
+	 */
+	bool post_buf_empty_masked;
 };
 
 /**
Signature · 1 line
2.55.0
#7 lore raw

Re: [PATCH 5/8] drm/rockchip: vop2: Report POST_BUF_EMPTY at most once per frame

Thank you for your contribution! Sashiko AI review found 4 potential issues to consider: - [Medium] drm/rockchip: vop2: stale FS status in vop2_crtc_handle_post_buf_empty() - [Medium] drm/rockchip…

Thank you for your contribution! Sashiko AI review found 4 potential issues to consider:
- [Medium] drm/rockchip: vop2: stale FS status in vop2_crtc_handle_post_buf_empty()
- [Medium] drm/rockchip: vop2: VP_INT_FS_FIELD left enabled across CRTC disable
- [Low] drm/rockchip: vop2: vop2_crtc_enable_vblank() clears pending FS irq
- [Low] drm/rockchip: vop2: missing Fixes trailer for POST_BUF_EMPTY irq storm
--

commit 225fca8d582460d4af5df41d587daa2368d818f1
Author: Arun Iyengar <[email protected]>

Quoted 10 lines

drm/rockchip: vop2: Report POST_BUF_EMPTY at most once per frame

POST_BUF_EMPTY is raised for every line on which the post processing stage of a video port finds no data. The interrupt handler only rate-limits the error message and leaves the interrupt enabled, so an underflowing video port keeps the CPU in the interrupt handler 50000 to 300000 times per second, for as long as the configuration that causes the underflow stays in place (e.g. 120000 interrupts per second for 3840x2160@120 with two full screen layers on one AXI port).

Quoted 8 lines

Mask POST_BUF_EMPTY when it fires and unmask it at the next frame start. The frame start (FS) interrupt is enabled for that frame even when vblank reporting is off, and disabled again once POST_BUF_EMPTY is re-armed. A new per video port lock serialises the interrupt enable bookkeeping between the interrupt handler and the vblank callbacks. The error is still reported, now at most once per frame and video port.

[Severity: Low]
This fixes a per-line interrupt storm on underflowing video ports. Should this include:

Fixes 604be85547ce ("drm/rockchip: Add VOP2 driver")
Quoted 14 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +6 -0
index 9aeb90c6aa4b1..3323e50224c55 100644
@@ -841,6 +841,48 @@ static void vop2_crtc_disable_irq(struct vop2_video_port *vp, u32 irq)
 	vop2_writel(vop2, RK3568_VP_INT_EN(vp->id), irq << 16);
 }
 
+/*
+ * POST_BUF_EMPTY is raised for every line the post processing stage finds
+ * no data for, so an underflowing video port can raise it 100000 times per
+ * second. Report it at most once per frame: mask it when it fires and
+ * unmask it at the next frame start, using the FS interrupt even when
+ * vblank reporting is off.

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static void vop2_crtc_disable_irq(struct vop2_video_port *vp, u32 irq) · line 859

Quoted 10 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +10 -0
+ */
+static void vop2_crtc_enable_post_buf_empty_irq(struct vop2_video_port *vp)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->post_buf_empty_masked = false;
+	vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
+}

[Severity: Medium]
Can VP_INT_FS_FIELD stay enabled permanently after a CRTC disable and re-enable cycle?

If VP_INT_POST_BUF_EMPTY fires during the last frame of a video port (either before drm_crtc_vblank_off() or while vop2_crtc_atomic_disable() waits on vp->dsp_hold_completion), vop2_crtc_handle_post_buf_empty() sets vp->post_buf_empty_masked = true and enables VP_INT_FS_FIELD. drm_crtc_vblank_off() -> vop2_crtc_disable_vblank() then sees vp->post_buf_empty_masked == true and leaves VP_INT_FS_FIELD enabled in RK3568_VP_INT_EN(vp->id) when the video port enters standby.

When the CRTC is later re-enabled (while another active video port kept VOP2 powered on), vop2_crtc_enable_post_buf_empty_irq() resets vp->post_buf_empty_masked = false without disabling VP_INT_FS_FIELD. Once vblank turns off, the video port runs with both vp->vblank_enabled and vp->post_buf_empty_masked false while VP_INT_FS_FIELD fires an unhandled interrupt on every frame. In addition, vop2_crtc_atomic_disable() and the err_put_enable_count error paths in vop2_crtc_atomic_enable() never disable VP_INT_POST_BUF_EMPTY.

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static void vop2_crtc_disable_irq(struct vop2_video_port *vp, u32 irq) · line 872

Quoted 13 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +13 -0
+
+static void vop2_crtc_handle_post_buf_empty(struct vop2_video_port *vp)
+{
+	struct vop2 *vop2 = vp->vop2;
+
+	spin_lock(&vp->irq_lock);
+	vop2_crtc_disable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	vp->post_buf_empty_masked = true;
+	/* don't clear a pending FS, it may carry a vblank event */
+	vop2_writel(vop2, RK3568_VP_INT_EN(vp->id),
+		    VP_INT_FS_FIELD << 16 | VP_INT_FS_FIELD);
+	spin_unlock(&vp->irq_lock);
+}

[Severity: Medium]
When vp->vblank_enabled is false, does unmasking VP_INT_FS_FIELD without clearing RK3568_VP_INT_CLR(vp->id) immediately trigger a spurious mid-frame FS interrupt?

VOP2 latches raw interrupt status even while an interrupt is masked, and vop2_isr() / rk3576_vp_isr() only clear bits returned by the masked status register RK3568_VP_INT_STATUS(vp->id). While vblank reporting is disabled, the raw VP_INT_FS_FIELD bit latched at the start of the current frame stays set during active scanout. Writing RK3568_VP_INT_EN(vp->id) here without clearing RK3568_VP_INT_CLR(vp->id) causes VP_INT_FS_FIELD to fire immediately on that stale status and call vop2_crtc_rearm_post_buf_empty() mid-frame, allowing VP_INT_POST_BUF_EMPTY to fire a second time in the same frame.

When vp->vblank_enabled is true, VP_INT_FS_FIELD is already enabled; when !vp->vblank_enabled, calling vop2_crtc_enable_irq(vp, VP_INT_FS_FIELD) will clear the stale raw status before enabling it.

[ ... ]

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static const struct drm_plane_funcs vop2_plane_funcs = { · line 1721

Quoted 13 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +4 -0
@@ -1668,8 +1710,12 @@ static const struct drm_plane_funcs vop2_plane_funcs = {
 static int vop2_crtc_enable_vblank(struct drm_crtc *crtc)
 {
 	struct vop2_video_port *vp = to_vop2_video_port(crtc);
+	unsigned long flags;
 
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->vblank_enabled = true;
 	vop2_crtc_enable_irq(vp, VP_INT_FS_FIELD);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
 
 	return 0;
 }

[Severity: Low]
Can vop2_crtc_enable_vblank() clear a pending VP_INT_FS_FIELD interrupt if vp->post_buf_empty_masked is already true?

When vp->post_buf_empty_masked is true, VP_INT_FS_FIELD is already enabled in hardware. Calling vop2_crtc_enable_irq(vp, VP_INT_FS_FIELD) unconditionally writes RK3568_VP_INT_CLR(vp->id), which can drop a pending frame-start interrupt that raced with vop2_crtc_enable_vblank() and delay both vblank handling and vop2_crtc_rearm_post_buf_empty() by a frame. Guard the vop2_crtc_enable_irq() call with if (!vp->post_buf_empty_masked), matching vop2_crtc_disable_vblank().

Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=5
#8 lore raw

Re: [PATCH 5/8] drm/rockchip: vop2: Report POST_BUF_EMPTY at most once per frame

In reply to Arun Iyengar

Hi Arun,

Quoted 48 lines · On 11/10/2026 3:18 PM, Arun Iyengar via B4 Relay wrote:

From: Arun Iyengar <[email protected]>

POST_BUF_EMPTY is raised for every line on which the post processing stage of a video port finds no data. The interrupt handler only rate-limits the error message and leaves the interrupt enabled, so an underflowing video port keeps the CPU in the interrupt handler 50000 to 300000 times per second, for as long as the configuration that causes the underflow stays in place (e.g. 120000 interrupts per second for 3840x2160@120 with two full screen layers on one AXI port).

Mask POST_BUF_EMPTY when it fires and unmask it at the next frame start. The frame start (FS) interrupt is enabled for that frame even when vblank reporting is off, and disabled again once POST_BUF_EMPTY is re-armed. A new per video port lock serialises the interrupt enable bookkeeping between the interrupt handler and the vblank callbacks. The error is still reported, now at most once per frame and video port.

---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 63 ++++++++++++++++++++++++++--
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.h | 10 +++++
 2 files changed, 70 insertions(+), 3 deletions(-)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +17 -0
index 9aeb90c6aa4b..3323e50224c5 100644
@@ -841,6 +841,48 @@ static void vop2_crtc_disable_irq(struct vop2_video_port *vp, u32 irq)
 	vop2_writel(vop2, RK3568_VP_INT_EN(vp->id), irq << 16);
 }
 
+/*
+ * POST_BUF_EMPTY is raised for every line the post processing stage finds
+ * no data for, so an underflowing video port can raise it 100000 times per
+ * second. Report it at most once per frame: mask it when it fires and
+ * unmask it at the next frame start, using the FS interrupt even when
+ * vblank reporting is off.
+ */
+static void vop2_crtc_enable_post_buf_empty_irq(struct vop2_video_port *vp)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->post_buf_empty_masked = false;
+	vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
+}
+

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static void vop2_crtc_disable_irq(struct vop2_video_port *vp, u32 irq) · line 870

Quoted 10 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +10 -0
+static void vop2_crtc_handle_post_buf_empty(struct vop2_video_port *vp)
+{
+	struct vop2 *vop2 = vp->vop2;
+
+	spin_lock(&vp->irq_lock);
+	vop2_crtc_disable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	vp->post_buf_empty_masked = true;
+	/* don't clear a pending FS, it may carry a vblank event */
+	vop2_writel(vop2, RK3568_VP_INT_EN(vp->id),
+		    VP_INT_FS_FIELD << 16 | VP_INT_FS_FIELD);

Do we really need this? Disabling the POST_BUF_EMPTY IRQ should not affect the FS_FIELD IRQ, because this register has write mask.

Quoted 127 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +33 -3
+	spin_unlock(&vp->irq_lock);
+}
+
+static void vop2_crtc_rearm_post_buf_empty(struct vop2_video_port *vp)
+{
+	spin_lock(&vp->irq_lock);
+	if (vp->post_buf_empty_masked) {
+		vp->post_buf_empty_masked = false;
+		vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+		if (!vp->vblank_enabled)
+			vop2_crtc_disable_irq(vp, VP_INT_FS_FIELD);
+	}
+	spin_unlock(&vp->irq_lock);
+}
+
 static int vop2_core_clks_prepare_enable(struct vop2 *vop2)
 {
 	int ret;
@@ -1668,8 +1710,12 @@ static const struct drm_plane_funcs vop2_plane_funcs = {
 static int vop2_crtc_enable_vblank(struct drm_crtc *crtc)
 {
 	struct vop2_video_port *vp = to_vop2_video_port(crtc);
+	unsigned long flags;
 
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->vblank_enabled = true;
 	vop2_crtc_enable_irq(vp, VP_INT_FS_FIELD);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
 
 	return 0;
 }
@@ -1677,8 +1723,13 @@ static int vop2_crtc_enable_vblank(struct drm_crtc *crtc)
 static void vop2_crtc_disable_vblank(struct drm_crtc *crtc)
 {
 	struct vop2_video_port *vp = to_vop2_video_port(crtc);
+	unsigned long flags;
 
-	vop2_crtc_disable_irq(vp, VP_INT_FS_FIELD);
+	spin_lock_irqsave(&vp->irq_lock, flags);
+	vp->vblank_enabled = false;
+	if (!vp->post_buf_empty_masked)
+		vop2_crtc_disable_irq(vp, VP_INT_FS_FIELD);
+	spin_unlock_irqrestore(&vp->irq_lock, flags);
 }
 
 static enum drm_mode_status vop2_crtc_mode_valid(struct drm_crtc *crtc,
@@ -1977,7 +2028,7 @@ static void vop2_crtc_atomic_enable(struct drm_crtc *crtc,
 
 	vcstate->yuv_overlay = is_yuv_output(vcstate->bus_format);
 
-	vop2_crtc_enable_irq(vp, VP_INT_POST_BUF_EMPTY);
+	vop2_crtc_enable_post_buf_empty_irq(vp);
 
 	polflags = 0;
 	if (vcstate->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
@@ -2535,6 +2586,7 @@ static irqreturn_t rk3576_vp_isr(int irq, void *data)
 	}
 
 	if (irqs & VP_INT_FS_FIELD) {
+		vop2_crtc_rearm_post_buf_empty(vp);
 		drm_crtc_handle_vblank(crtc);
 		spin_lock(&crtc->dev->event_lock);
 		if (vp->event) {
@@ -2552,6 +2604,7 @@ static irqreturn_t rk3576_vp_isr(int irq, void *data)
 	}
 
 	if (irqs & VP_INT_POST_BUF_EMPTY) {
+		vop2_crtc_handle_post_buf_empty(vp);
 		drm_err_ratelimited(vop2->drm, "POST_BUF_EMPTY irq err at vp%d\n", vp->id);
 		ret = IRQ_HANDLED;
 	}
@@ -2591,6 +2644,7 @@ static irqreturn_t vop2_isr(int irq, void *data)
 			}
 
 			if (irqs & VP_INT_FS_FIELD) {
+				vop2_crtc_rearm_post_buf_empty(vp);
 				drm_crtc_handle_vblank(crtc);
 				spin_lock(&crtc->dev->event_lock);
 				if (vp->event) {
@@ -2608,6 +2662,7 @@ static irqreturn_t vop2_isr(int irq, void *data)
 			}
 
 			if (irqs & VP_INT_POST_BUF_EMPTY) {
+				vop2_crtc_handle_post_buf_empty(vp);
 				drm_err_ratelimited(vop2->drm,
 						    "POST_BUF_EMPTY irq err at vp%d\n",
 						    vp->id);
@@ -2984,7 +3039,7 @@ static int vop2_bind(struct device *dev, struct device *master, void *data)
 	struct vop2 *vop2;
 	struct resource *res;
 	size_t alloc_size;
-	int ret;
+	int ret, i;
 
 	vop2_data = of_device_get_match_data(dev);
 	if (!vop2_data)
@@ -3102,6 +3157,8 @@ static int vop2_bind(struct device *dev, struct device *master, void *data)
 	mutex_init(&vop2->vop2_lock);
 	mutex_init(&vop2->ovl_lock);
 	spin_lock_init(&vop2->axi_lock);
+	for (i = 0; i < ARRAY_SIZE(vop2->vps); i++)
+		spin_lock_init(&vop2->vps[i].irq_lock);
 
 	ret = devm_request_irq(dev, vop2->irq, vop2_isr, IRQF_SHARED, dev_name(dev), vop2);
 	if (ret)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.h +10 -0
index f1e35967e67f..7de32bef8d7b 100644
@@ -272,6 +272,16 @@ struct vop2_video_port {
 	struct drm_pending_vblank_event *event;
 
 	unsigned int nlayers;
+
+	/** @irq_lock: protects @vblank_enabled and @post_buf_empty_masked */
+	spinlock_t irq_lock;
+	/** @vblank_enabled: the FS interrupt is enabled for vblank reporting */
+	bool vblank_enabled;
+	/**
+	 * @post_buf_empty_masked: POST_BUF_EMPTY is masked until the next
+	 * frame start
+	 */
+	bool post_buf_empty_masked;
 };
 
 /**
Signature · 2 lines
Best, 
Chaoyi
#9 lore raw

PATCH 6/8 drm/rockchip: vop2: Find the first mixer of a video port with Esmart3 too

In reply to Arun Iyengar

vop2_find_start_mixer_id_for_vp() looks for the first layer that holds a window of the video port, but for_each_set_bit() takes the number of bits to search, and ROCKCHIP_VOP2_ESMART3 is the highest window id, so Esmart3 is never found. A video port whose bottom layer shows Esmart3 then starts its alpha setup at the mixer of a higher layer, or, if Esmart3 is its only window, past all layers, and programs mixers of other video ports.

Search all window ids.

---
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +1 -1
index 83203d18865b..2843bfb36341 100644
@@ -1889,7 +1889,7 @@ static int vop2_find_start_mixer_id_for_vp(struct vop2_video_port *vp)
 
 	for (i = 0; i < 31; i += 4) {
 		match = false;
-		for_each_set_bit(phys_id, &win_mask, ROCKCHIP_VOP2_ESMART3) {
+		for_each_set_bit(phys_id, &win_mask, ROCKCHIP_VOP2_ESMART3 + 1) {
 			win = vop2_find_win_by_phys_id(vop2, phys_id);
 			if (win->data->layer_sel_id[vp->id] == ((layer_sel >> i) & 0xf)) {
 				match = true;
Signature · 1 line
2.55.0
#10 lore raw

Re: [PATCH 6/8] drm/rockchip: vop2: Find the first mixer of a video port with Esmart3 too

Thank you for your contribution! Sashiko AI review found 1 potential issue to consider: - [Low] drm/rockchip: missing Fixes trailer for vop2_find_start_mixer_id_for_vp() --

Thank you for your contribution! Sashiko AI review found 1 potential issue to consider:
- [Low] drm/rockchip: missing Fixes trailer for vop2_find_start_mixer_id_for_vp()
--

commit bef29062242358932c819e26dffcbfccfee3a800
Author: Arun Iyengar <[email protected]>

Quoted 9 lines

drm/rockchip: vop2: Find the first mixer of a video port with Esmart3 too

vop2_find_start_mixer_id_for_vp() looks for the first layer that holds a window of the video port, but for_each_set_bit() takes the number of bits to search, and ROCKCHIP_VOP2_ESMART3 is the highest window id, so Esmart3 is never found. A video port whose bottom layer shows Esmart3 then starts its alpha setup at the mixer of a higher layer, or, if Esmart3 is its only window, past all layers, and programs mixers of other video ports.

Quoted 3 lines

Search all window ids.

[Severity: Low]
This fixes the window bitmask search bound in vop2_find_start_mixer_id_for_vp(). Should this include:

Fixes d3fe9aa49585 ("drm/rockchip: vop2: Use OVL_LAYER_SEL configuration instead of use win_mask calculate used layers")
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=6
#11 lore raw

Re: [PATCH 6/8] drm/rockchip: vop2: Find the first mixer of a video port with Esmart3 too

In reply to Arun Iyengar

Hi Arun,

Quoted 21 lines · On 11/10/2026 3:18 PM, Arun Iyengar via B4 Relay wrote:

From: Arun Iyengar <[email protected]>

vop2_find_start_mixer_id_for_vp() looks for the first layer that holds a window of the video port, but for_each_set_bit() takes the number of bits to search, and ROCKCHIP_VOP2_ESMART3 is the highest window id, so Esmart3 is never found. A video port whose bottom layer shows Esmart3 then starts its alpha setup at the mixer of a higher layer, or, if Esmart3 is its only window, past all layers, and programs mixers of other video ports.

Search all window ids.

---
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +0 -0
index 83203d18865b..2843bfb36341 100644

drivers/gpu/drm/rockchip/rockchip_vop2_reg.c static int vop2_find_start_mixer_id_for_vp(struct vop2_video_port *vp) · line 1892

Quoted 5 lines
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +1 -1
@@ -1889,7 +1889,7 @@ static int vop2_find_start_mixer_id_for_vp(struct vop2_video_port *vp)
 
 	for (i = 0; i < 31; i += 4) {
 		match = false;
-		for_each_set_bit(phys_id, &win_mask, ROCKCHIP_VOP2_ESMART3) {
+		for_each_set_bit(phys_id, &win_mask, ROCKCHIP_VOP2_ESMART3 + 1) {

It would be better to add ROCKCHIP_VOP_MAX_LAYER_ID after ROCKCHIP_VOP2_ESMART3.

Quoted 4 lines
drivers/gpu/drm/rockchip/rockchip_vop2_reg.c +0 -0
 			win = vop2_find_win_by_phys_id(vop2, phys_id);
 			if (win->data->layer_sel_id[vp->id] == ((layer_sel >> i) & 0xf)) {
 				match = true;
Signature · 2 lines
Best, 
Chaoyi
#12 lore raw

PATCH 7/8 drm/rockchip: vop2: Keep the other LUT_PORT_SEL fields on gamma LUT updates

In reply to Arun Iyengar

On RK3588 the gamma LUT of a video port is written through a window that GAMMA_AHB_WRITE_SEL in SYS_CTRL_LUT_PORT_SEL selects. The register also holds the dclk source selection of video ports 0 and 2 and the enable of the video port 0/1 merge for modes wider than 4096 pixels, which writing the whole register clears.

Only update the write select field.

---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +3 -2
index 3323e50224c5..9ad138457204 100644
@@ -1774,8 +1774,9 @@ static void vop2_crtc_atomic_set_gamma_seamless(struct vop2 *vop2,
 						struct vop2_video_port *vp,
 						struct drm_crtc *crtc)
 {
-	vop2_writel(vop2, RK3568_LUT_PORT_SEL,
-		    FIELD_PREP(RK3588_LUT_PORT_SEL__GAMMA_AHB_WRITE_SEL, vp->id));
+	regmap_update_bits(vop2->map, RK3568_LUT_PORT_SEL,
+			   RK3588_LUT_PORT_SEL__GAMMA_AHB_WRITE_SEL,
+			   FIELD_PREP(RK3588_LUT_PORT_SEL__GAMMA_AHB_WRITE_SEL, vp->id));
 	vop2_vp_dsp_lut_enable(vp);
 	vop2_crtc_write_gamma_lut(vop2, crtc);
 	vop2_vp_dsp_lut_update_enable(vp);
Signature · 1 line
2.55.0
#13 lore raw

Re: [PATCH 7/8] drm/rockchip: vop2: Keep the other LUT_PORT_SEL fields on gamma LUT updates

Thank you for your contribution! Sashiko AI review found 1 potential issue to consider: - [Low] drm/rockchip: vop2: missing Fixes trailer for commit 4f537776340d --

Thank you for your contribution! Sashiko AI review found 1 potential issue to consider:
- [Low] drm/rockchip: vop2: missing Fixes trailer for commit 4f537776340d
--

commit a8803c2d42085266d5dfa3113cf2bcad402ebf13
Author: Arun Iyengar <[email protected]>

Quoted 11 lines

drm/rockchip: vop2: Keep the other LUT_PORT_SEL fields on gamma LUT updates

On RK3588 the gamma LUT of a video port is written through a window that GAMMA_AHB_WRITE_SEL in SYS_CTRL_LUT_PORT_SEL selects. The register also holds the dclk source selection of video ports 0 and 2 and the enable of the video port 0/1 merge for modes wider than 4096 pixels, which writing the whole register clears.

Only update the write select field.

[Severity: Low]
This fixes the full-register write to RK3568_LUT_PORT_SEL in vop2_crtc_atomic_set_gamma_seamless(). Should this include:

Fixes 4f537776340d ("rockchip/drm: vop2: add support for gamma LUT")
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=7
Reviewed-by on v1 7/8
#14 lore raw

Re: [PATCH 7/8] drm/rockchip: vop2: Keep the other LUT_PORT_SEL fields on gamma LUT updates

In reply to Arun Iyengar
Quoted 11 lines · On 11/10/2026 3:18 PM, Arun Iyengar via B4 Relay wrote:

From: Arun Iyengar <[email protected]>

On RK3588 the gamma LUT of a video port is written through a window that GAMMA_AHB_WRITE_SEL in SYS_CTRL_LUT_PORT_SEL selects. The register also holds the dclk source selection of video ports 0 and 2 and the enable of the video port 0/1 merge for modes wider than 4096 pixels, which writing the whole register clears.

Only update the write select field.

Quoted 21 lines
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +3 -2
index 3323e50224c5..9ad138457204 100644
@@ -1774,8 +1774,9 @@ static void vop2_crtc_atomic_set_gamma_seamless(struct vop2 *vop2,
 						struct vop2_video_port *vp,
 						struct drm_crtc *crtc)
 {
-	vop2_writel(vop2, RK3568_LUT_PORT_SEL,
-		    FIELD_PREP(RK3588_LUT_PORT_SEL__GAMMA_AHB_WRITE_SEL, vp->id));
+	regmap_update_bits(vop2->map, RK3568_LUT_PORT_SEL,
+			   RK3588_LUT_PORT_SEL__GAMMA_AHB_WRITE_SEL,
+			   FIELD_PREP(RK3588_LUT_PORT_SEL__GAMMA_AHB_WRITE_SEL, vp->id));
 	vop2_vp_dsp_lut_enable(vp);
 	vop2_crtc_write_gamma_lut(vop2, crtc);
 	vop2_vp_dsp_lut_update_enable(vp);
Signature · 2 lines
Best, 
Chaoyi
#15 lore raw

PATCH 8/8 drm/rockchip: vop2: Fix the AFBC offsets of a source that starts inside a superblock

In reply to Arun Iyengar

The AFBC decoder of a window takes the position of the source in the framebuffer (AFBC_PIC_OFFSET), the number of superblock columns to decode (AFBC_TILE_NUM) and the offset of the first pixel inside its superblock (the transform offset). For a source that doesn't start at x = 0:

- The tile number only counts the superblocks of the source width, one short when the source starts inside a superblock and ends inside another one.
- The transform offset is the whole x position, truncated to the 8 bit field, instead of the position in the 16 pixel wide superblock.

Count the superblock columns from the first one the source touches, and take the x offset in the superblock, like the vendor kernel does for the not mirrored cases. The X mirrored and rotated cases are left as they are.

---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +4 -3
index 9ad138457204..dfb76bfbc358 100644
@@ -486,7 +486,7 @@ static u32 vop2_afbc_transform_offset(struct drm_plane_state *pstate,
 		ty = act_yoffset;
 		break;
 	case DRM_MODE_REFLECT_Y:
-		tx = act_xoffset;
+		tx = act_xoffset & 0xf;
 		ty = bottom_crop_line_num - act_yoffset;
 		break;
 	case DRM_MODE_ROTATE_90:
@@ -498,7 +498,7 @@ static u32 vop2_afbc_transform_offset(struct drm_plane_state *pstate,
 		ty = vir_width - width - act_xoffset;
 		break;
 	case 0:
-		tx = act_xoffset;
+		tx = act_xoffset & 0xf;
 		ty = act_yoffset;
 		break;
 	}
@@ -1577,7 +1577,8 @@ static void vop2_plane_atomic_update(struct drm_plane *plane,
 		if (fb->modifier & AFBC_FORMAT_MOD_YTR)
 			afbc_format |= (1 << 4);
 
-		afbc_tile_num = ALIGN(src_w, block_w) / block_w;
+		/* Superblock columns the source covers, the first one partly */
+		afbc_tile_num = ALIGN(src_w + (src->x1 >> 16) % block_w, block_w) / block_w;
 
 		/*
 		 * AFBC pic_vir_width is count by pixel, this is different
Signature · 1 line
2.55.0
#16 lore raw

Re: [PATCH 8/8] drm/rockchip: vop2: Fix the AFBC offsets of a source that starts inside a superblock

Thank you for your contribution! Sashiko AI review found 2 potential issues to consider: - [Medium] drm/rockchip: vop2: wrong 32x8 AFBC x mask in vop2_afbc_transform_offset() - [Low] drm/rockchip…

Thank you for your contribution! Sashiko AI review found 2 potential issues to consider:
- [Medium] drm/rockchip: vop2: wrong 32x8 AFBC x mask in vop2_afbc_transform_offset()
- [Low] drm/rockchip: vop2: missing Fixes trailer for commit 604be85547ce
--

commit 1aeff8145623ebb58cb0a14969b5391365ee2e1c
Author: Arun Iyengar <[email protected]>

Quoted 14 lines

drm/rockchip: vop2: Fix the AFBC offsets of a source that starts inside a superblock

The AFBC decoder of a window takes the position of the source in the framebuffer (AFBC_PIC_OFFSET), the number of superblock columns to decode (AFBC_TILE_NUM) and the offset of the first pixel inside its superblock (the transform offset). For a source that doesn't start at x = 0:

- The tile number only counts the superblocks of the source width, one short when the source starts inside a superblock and ends inside another one.
- The transform offset is the whole x position, truncated to the 8 bit field, instead of the position in the 16 pixel wide superblock.

Quoted 5 lines

Count the superblock columns from the first one the source touches, and take the x offset in the superblock, like the vendor kernel does for the not mirrored cases. The X mirrored and rotated cases are left as they are.

[Severity: Low]
Since this fixes a bug introduced with the initial VOP2 driver, should it include:

Fixes 604be85547ce ("drm/rockchip: Add VOP2 driver")
Quoted 14 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +1 -1
index 9ad138457204f..dfb76bfbc358f 100644
@@ -486,7 +486,7 @@ static u32 vop2_afbc_transform_offset(struct drm_plane_state *pstate,
 		ty = act_yoffset;
 		break;
 	case DRM_MODE_REFLECT_Y:
-		tx = act_xoffset;
+		tx = act_xoffset & 0xf;
 		ty = bottom_crop_line_num - act_yoffset;
 		break;
 	case DRM_MODE_ROTATE_90:

drivers/gpu/drm/rockchip/rockchip_drm_vop2.c static u32 vop2_afbc_transform_offset(struct drm_plane_state *pstate, · line 504

Quoted 8 lines
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c +1 -1
@@ -498,7 +498,7 @@ static u32 vop2_afbc_transform_offset(struct drm_plane_state *pstate,
 		ty = vir_width - width - act_xoffset;
 		break;
 	case 0:
-		tx = act_xoffset;
+		tx = act_xoffset & 0xf;
 		ty = act_yoffset;
 		break;
 	}

[Severity: Medium]
Does masking act_xoffset with 0xf break 32x8 AFBC superblocks when (act_xoffset % 32) is between 16 and 31?

In vop2_plane_atomic_update(), block_w is 32 when AFBC_FORMAT_MOD_BLOCK_SIZE_32x8 is set (such as on RK3576 cluster windows), and afbc_tile_num is computed using (src->x1 >> 16) % block_w. Hardcoding 0xf here truncates tx to 0..15 instead of 0..31, shifting the decoded plane horizontally by 16 pixels whenever bit 4 of act_xoffset is set.

Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=8
#17 lore raw
In reply to Arun Iyengar

Hi Arun,

Quoted 13 lines · On 11/10/2026 3:18 PM, Arun Iyengar via B4 Relay wrote:

This series collects fixes for the RK3588 VOP2 found while bringing up HDMI and DisplayPort output on an Orange Pi 5 (RK3588S).

Patches 1 and 2 fix the RK3588 interface setup: rk3588_calc_cru_cfg() leaves dividers it does not use uninitialised and the garbage ends up in VP_CLK_CTRL, and rk3588_get_hdmi_pol() decodes the POLFLAG bits it is handed as DRM mode flags, so the GRF sync polarity bits are wrong for most modes.

Patch 3 stops the RK3588 Cluster windows from advertising AFBC with the lossless colour transform (YTR) for RGB565/BGR565, which the decoder cannot display (black picture plus POST_BUF_EMPTY).

Quoted 12 lines

Patches 4 and 5 deal with POST_BUF_EMPTY underflows. The VOP2 fetches through two AXI read ports but the port of each window is fixed in the window table, so the usual primary plane plus overlay configuration of a video port puts both layers on one port while the other sits idle. One port cannot sustain two full screen 4K@120Hz layers (measured: the fetch rate collapses from ~6 GB/s to ~3 GB/s and about half of all lines underflow). Patch 4 assigns the port when a window starts fetching, balancing the estimated load; patch 5 rate-limits the POST_BUF_EMPTY interrupt to once per frame, since an underflowing port otherwise keeps the CPU in the interrupt handler 50000 to 300000 times per second.

Have you checked the aclk_vop rate?

Quoted 50 lines

Patches 6 to 8 are smaller fixes: the start mixer search skipped Esmart3 (for_each_set_bit() was given the highest window id as the bit count), a gamma LUT update cleared the other fields of LUT_PORT_SEL (the VP0/VP2 dclk source selection and the VP0/VP1 merge enable), and the AFBC tile count and transform offset were wrong for a source that starts inside a 16 pixel superblock.

Tested on an Orange Pi 5 (RK3588S) with an HDMI 2.1 TV and a DisplayPort monitor, pictures judged with a camera. Patches 1 and 2:
VP0_CLK_CTRL reads back without the garbage dclk_out divider, the sync polarities seen by the HDMI controller (VIDEO_INTERFACE_STATUS0) match the mode flags for +/+ (1080p, 2160p) and -/- (720x480, 640x480) modes, and the picture is correct over TMDS and FRL modes from 27 to 1188 MHz. Patch 3: RGB565 is offered on the Cluster windows only without YTR, and those planes scan out correctly on three Cluster windows. Patches 4 and 5: 3840x2160@120 with a full screen overlay (previously ~120000 POST_BUF_EMPTY per second and a scrambled picture) and a dual-display session (HDMI 4K@60 plus DP 4K@30, two video players, ten minutes) run with zero underflows. Patches 6 to 8 were found while driving Esmart3 and partial AFBC overlays: an AFBC overlay placed at x=1001 shows correctly. All eight have been in the board's kernel for the display test runs since.

This series was developed with Claude (Anthropic) as a coding assistant:
it wrote the code and the commit messages, and I reviewed and tested every change as described above.

---
Arun Iyengar (8):
drm/rockchip: vop2: Don't use uninitialised dividers on RK3588 drm/rockchip: vop2: Fix the HDMI sync polarity on RK3588 drm/rockchip: vop2: Don't accept AFBC YTR for RGB565 on RK3588 drm/rockchip: vop2: Balance window fetches across both AXI ports on RK3588 drm/rockchip: vop2: Report POST_BUF_EMPTY at most once per frame drm/rockchip: vop2: Find the first mixer of a video port with Esmart3 too drm/rockchip: vop2: Keep the other LUT_PORT_SEL fields on gamma LUT updates drm/rockchip: vop2: Fix the AFBC offsets of a source that starts inside a superblock

 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 186 +++++++++++++++++++++++++--
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.h |  24 ++++
 drivers/gpu/drm/rockchip/rockchip_vop2_reg.c |  27 +++-
 3 files changed, 223 insertions(+), 14 deletions(-)

---
base-commit: 8deaade4a5a4ff635df91e246e42139ab2b33f6d
change-id: 20261110-vop2-fixes-fa45142799c1

Best regards,

Signature · 1 line
Arun Iyengar <[email protected]>
Signature · 2 lines
Best, 
Chaoyi