x86 FPU cleanups (v2)
cover x86 FPU cleanups (v2)
This patch set cleans up and merges the 32-bit and 64-bit FPU code.
v2:
- Don't write to %cr4 unless some bits are set
- Reworked the fpu_save_init() merge
[PATCH 01/12] x86: Use correct type for %cr4
[PATCH 02/12] x86: Merge fpu_init()
[PATCH 03/12] x86: Merge tolerant_fwait()
[PATCH 04/12] x86: Merge __save_init_fpu()
[PATCH 05/12] x86-64: Disable preemption when using TS_USEDFPU [PATCH 06/12] x86-64: Fix %cs value in convert_from_fxsr() [PATCH 07/12] x86-64: Simplify constraints for fxsave/fxtstor [PATCH 08/12] x86-32: Remove math_emulate stub [PATCH 09/12] x86: Remove unnecessary ifdefs from i387 code. [PATCH 10/12] x86: Remove PSHUFB_XMM5_* macros [PATCH 11/12] x86-32: Rewrite fpu_save_init()
[PATCH 12/12] x86: Merge fpu_save_init()
arch/x86/include/asm/i387.h | 195 ++++++++++--------------------------- arch/x86/include/asm/processor.h | 4 +- arch/x86/kernel/cpu/common.c | 7 -- arch/x86/kernel/i387.c | 52 +++++------ arch/x86/kernel/process_64.c | 2 +- arch/x86/kernel/traps.c | 35 +------ 6 files changed, 84 insertions(+), 211 deletions(-)
PATCH 1/12 x86: Use correct type for %cr4
%cr4 is 64-bit in 64-bit mode (although the upper 32-bits are currently reserved). Use unsigned long for the temporary variable to get the right size.
--- arch/x86/include/asm/processor.h | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)
arch/x86/include/asm/processor.h +2 -2
@@ -602,7 +602,7 @@ extern unsigned long mmu_cr4_features;static inline void set_in_cr4 (unsigned long mask) { -unsigned cr4; +unsigned long cr4; mmu_cr4_features |= mask; cr4 =read_cr4 ();
@@ -612,7 +612,7 @@ static inline void set_in_cr4(unsigned long mask)static inline void clear_in_cr4 (unsigned long mask) { -unsigned cr4; +unsigned long cr4; mmu_cr4_features &= ~mask; cr4 =read_cr4 ();
Signature · 1 line
1.7.2.2
Re: [PATCH 01/12] x86: Use correct type for %cr4
Quoted 4 lines · Brian Gerst
%cr4 is 64-bit in 64-bit mode (although the upper 32-bits are currently reserved). Use unsigned long for the temporary variable to get the right size.
Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86: Use correct type for %cr4
In reply to Brian GerstCommit-ID: 2df7a6e9e8e67c19e5fe2eac3f2d2223b7bb4a7b Gitweb: http://git.kernel.org/tip/2df7a6e9e8e67c19e5fe2eac3f2d2223b7bb4a7b Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:08 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:16:13 -0700
x86: Use correct type for %cr4
%cr4 is 64-bit in 64-bit mode (although the upper 32-bits are currently reserved). Use unsigned long for the temporary variable to get the right size.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/processor.h | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)
arch/x86/include/asm/processor.h +2 -2
@@ -602,7 +602,7 @@ extern unsigned long mmu_cr4_features;static inline void set_in_cr4 (unsigned long mask) { -unsigned cr4; +unsigned long cr4; mmu_cr4_features |= mask; cr4 =read_cr4 ();
@@ -612,7 +612,7 @@ static inline void set_in_cr4(unsigned long mask)static inline void clear_in_cr4 (unsigned long mask) { -unsigned cr4; +unsigned long cr4; mmu_cr4_features &= ~mask; cr4 =read_cr4 ();
PATCH 2/12 x86: Merge fpu_init()
In reply to Brian GerstMake fpu_init() handle 32-bit setup.
--- arch/x86/kernel/cpu/common.c | 7 ------- arch/x86/kernel/i387.c | 30 ++++++++++++++---------------- arch/x86/kernel/traps.c | 12 ------------ 3 files changed, 14 insertions(+), 35 deletions(-)
arch/x86/kernel/cpu/common.c +0 -7
@@ -1264,13 +1264,6 @@ void __cpuinit cpu_init(void)clear_all_debug_regs ();dbg_restore_debug_regs (); -/* -* Force FPU initialization: -*/ -current_thread_info ()->status =0 ; -clear_used_math (); -mxcsr_feature_mask_init (); -fpu_init ();xsave_init (); }
arch/x86/kernel/i387.c +14 -16
@@ -80,7 +80,6 @@ static void __cpuinit init_thread_xstate(void)#endif } -#ifdef CONFIG_X86_64 /* * Called at bootup to set up the initial FPU state that is later cloned * into all processes.
@@ -88,12 +87,21 @@ static void __cpuinit init_thread_xstate(void)void __cpuinit fpu_init (void ) { -unsigned long oldcr0 =read_cr0 (); - -set_in_cr4 (X86_CR4_OSFXSR ); -set_in_cr4 (X86_CR4_OSXMMEXCPT ); +unsigned long cr0; +unsigned long cr4_mask =0 ; -write_cr0 (oldcr0 & ~(X86_CR0_TS |X86_CR0_EM ));/* clear TS and EM */ +if (cpu_has_fxsr) + cr4_mask |=X86_CR4_OSFXSR ; +if (cpu_has_xmm) + cr4_mask |=X86_CR4_OSXMMEXCPT ; +if (cr4_mask) +set_in_cr4 (cr4_mask); + + cr0 =read_cr0 (); + cr0 &= ~(X86_CR0_TS |X86_CR0_EM );/* clear TS and EM */ +if (!HAVE_HWFP ) + cr0 |=X86_CR0_EM ; +write_cr0 (cr0);if (!smp_processor_id ())init_thread_xstate ();
@@ -104,16 +112,6 @@ void __cpuinit fpu_init(void)clear_used_math (); } -#else /* CONFIG_X86_64 */ - -void __cpuinit fpu_init (void ) -{ -if (!smp_processor_id ()) -init_thread_xstate (); -} - -#endif /* CONFIG_X86_32 */ -void fpu_finit (struct fpu *fpu) {#ifdef CONFIG_X86_32
arch/x86/kernel/traps.c +0 -12
@@ -881,18 +881,6 @@ void __init trap_init(void)#endif #ifdef CONFIG_X86_32 -if (cpu_has_fxsr) { -printk (KERN_INFO "Enabling fast FPU save and restore... " ); -set_in_cr4 (X86_CR4_OSFXSR ); -printk ("done.\n" ); - } -if (cpu_has_xmm) { -printk (KERN_INFO -"Enabling unmasked SIMD FPU exception support... " ); -set_in_cr4 (X86_CR4_OSXMMEXCPT ); -printk ("done.\n" ); - } -set_system_trap_gate (SYSCALL_VECTOR , &system_call);set_bit (SYSCALL_VECTOR , used_vectors);#endif
Signature · 1 line
1.7.2.2
Re: [PATCH 02/12] x86: Merge fpu_init()
Quoted 3 lines · Brian Gerst
Make
fpu_init()handle 32-bit setup.Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86, fpu: Merge fpu_init()
In reply to Brian GerstCommit-ID: 6ac8bac2684235f4caf22a410549c582aa7327d6 Gitweb: http://git.kernel.org/tip/6ac8bac2684235f4caf22a410549c582aa7327d6 Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:09 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:16:20 -0700
x86, fpu: Merge fpu_init()
Make fpu_init() handle 32-bit setup.
LKML-Reference: <[email protected]>
--- arch/x86/kernel/cpu/common.c | 7 ------- arch/x86/kernel/i387.c | 30 ++++++++++++++---------------- arch/x86/kernel/traps.c | 12 ------------ 3 files changed, 14 insertions(+), 35 deletions(-)
arch/x86/kernel/cpu/common.c +0 -7
@@ -1264,13 +1264,6 @@ void __cpuinit cpu_init(void)clear_all_debug_regs ();dbg_restore_debug_regs (); -/* -* Force FPU initialization: -*/ -current_thread_info ()->status =0 ; -clear_used_math (); -mxcsr_feature_mask_init (); -fpu_init ();xsave_init (); }
arch/x86/kernel/i387.c +14 -16
@@ -85,7 +85,6 @@ static void __cpuinit init_thread_xstate(void)#endif } -#ifdef CONFIG_X86_64 /* * Called at bootup to set up the initial FPU state that is later cloned * into all processes.
@@ -93,12 +92,21 @@ static void __cpuinit init_thread_xstate(void)void __cpuinit fpu_init (void ) { -unsigned long oldcr0 =read_cr0 (); - -set_in_cr4 (X86_CR4_OSFXSR ); -set_in_cr4 (X86_CR4_OSXMMEXCPT ); +unsigned long cr0; +unsigned long cr4_mask =0 ; -write_cr0 (oldcr0 & ~(X86_CR0_TS |X86_CR0_EM ));/* clear TS and EM */ +if (cpu_has_fxsr) + cr4_mask |=X86_CR4_OSFXSR ; +if (cpu_has_xmm) + cr4_mask |=X86_CR4_OSXMMEXCPT ; +if (cr4_mask) +set_in_cr4 (cr4_mask); + + cr0 =read_cr0 (); + cr0 &= ~(X86_CR0_TS |X86_CR0_EM );/* clear TS and EM */ +if (!HAVE_HWFP ) + cr0 |=X86_CR0_EM ; +write_cr0 (cr0);if (!smp_processor_id ())init_thread_xstate ();
@@ -109,16 +117,6 @@ void __cpuinit fpu_init(void)clear_used_math (); } -#else /* CONFIG_X86_64 */ - -void __cpuinit fpu_init (void ) -{ -if (!smp_processor_id ()) -init_thread_xstate (); -} - -#endif /* CONFIG_X86_32 */ -void fpu_finit (struct fpu *fpu) {#ifdef CONFIG_X86_32
arch/x86/kernel/traps.c +0 -12
@@ -881,18 +881,6 @@ void __init trap_init(void)#endif #ifdef CONFIG_X86_32 -if (cpu_has_fxsr) { -printk (KERN_INFO "Enabling fast FPU save and restore... " ); -set_in_cr4 (X86_CR4_OSFXSR ); -printk ("done.\n" ); - } -if (cpu_has_xmm) { -printk (KERN_INFO -"Enabling unmasked SIMD FPU exception support... " ); -set_in_cr4 (X86_CR4_OSXMMEXCPT ); -printk ("done.\n" ); - } -set_system_trap_gate (SYSCALL_VECTOR , &system_call);set_bit (SYSCALL_VECTOR , used_vectors);#endif
PATCH 3/12 x86: Merge tolerant_fwait()
In reply to Brian GerstCommit e2e75c91 merged the math exception handler, allowing both 32-bit and 64-bit to handle math exceptions from kernel mode. Switch to using the 64-bit version of tolerant_fwait() without fnclex, which simply ignores the exception if one is still pending from userspace.
--- arch/x86/include/asm/i387.h | 19 ++++--------------- 1 files changed, 4 insertions(+), 15 deletions(-)
arch/x86/include/asm/i387.h +4 -15
@@ -77,15 +77,6 @@ static inline void sanitize_i387_state(struct task_struct *tsk) }#ifdef CONFIG_X86_64 - -/* Ignore delayed exceptions from user space */ -static inline void tolerant_fwait (void ) -{ - asmvolatile ("1: fwait\n" -"2:\n" - _ASM_EXTABLE(1b, 2b)); -} -static inline int fxrstor_checking (struct i387_fxsave_struct *fx) {int err;
@@ -220,11 +211,6 @@ extern void finit_soft_fpu(struct i387_soft_struct *soft);static inline void finit_soft_fpu (struct i387_soft_struct *soft) {}#endif -static inline void tolerant_fwait (void ) -{ - asmvolatile ("fnclex ; fwait" ); -} -/* perform fxrstor iff the processor has extended states, otherwise frstor */ static inline int fxrstor_checking (struct i387_fxsave_struct *fx) {
@@ -344,7 +330,10 @@ static inline void __unlazy_fpu(struct task_struct *tsk)static inline void __clear_fpu (struct task_struct *tsk) {if (task_thread_info (tsk)->status &TS_USEDFPU ) { -tolerant_fwait (); +/* Ignore delayed exceptions from user space */ + asmvolatile ("1: fwait\n" +"2:\n" + _ASM_EXTABLE(1b, 2b));task_thread_info (tsk)->status &= ~TS_USEDFPU ;stts (); }
Signature · 1 line
1.7.2.2
Re: [PATCH 03/12] x86: Merge tolerant_fwait()
Quoted 6 lines · Brian Gerst
Commit
e2e75c91merged the math exception handler, allowing both 32-bit and 64-bit to handle math exceptions from kernel mode. Switch to using the 64-bit version oftolerant_fwait()without fnclex, which simply ignores the exception if one is still pending from userspace.Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86, fpu: Merge tolerant_fwait()
In reply to Brian GerstCommit-ID: 51115d4d45700fc7c08306f7ba6e68551f526ae5 Gitweb: http://git.kernel.org/tip/51115d4d45700fc7c08306f7ba6e68551f526ae5 Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:10 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:16:25 -0700
x86, fpu: Merge tolerant_fwait()
Commit e2e75c91 merged the math exception handler, allowing both 32-bit and 64-bit to handle math exceptions from kernel mode. Switch to using the 64-bit version of tolerant_fwait() without fnclex, which simply ignores the exception if one is still pending from userspace.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 19 ++++--------------- 1 files changed, 4 insertions(+), 15 deletions(-)
arch/x86/include/asm/i387.h +4 -15
@@ -77,15 +77,6 @@ static inline void sanitize_i387_state(struct task_struct *tsk) }#ifdef CONFIG_X86_64 - -/* Ignore delayed exceptions from user space */ -static inline void tolerant_fwait (void ) -{ - asmvolatile ("1: fwait\n" -"2:\n" - _ASM_EXTABLE(1b, 2b)); -} -static inline int fxrstor_checking (struct i387_fxsave_struct *fx) {int err;
@@ -220,11 +211,6 @@ extern void finit_soft_fpu(struct i387_soft_struct *soft);static inline void finit_soft_fpu (struct i387_soft_struct *soft) {}#endif -static inline void tolerant_fwait (void ) -{ - asmvolatile ("fnclex ; fwait" ); -} -/* perform fxrstor iff the processor has extended states, otherwise frstor */ static inline int fxrstor_checking (struct i387_fxsave_struct *fx) {
@@ -344,7 +330,10 @@ static inline void __unlazy_fpu(struct task_struct *tsk)static inline void __clear_fpu (struct task_struct *tsk) {if (task_thread_info (tsk)->status &TS_USEDFPU ) { -tolerant_fwait (); +/* Ignore delayed exceptions from user space */ + asmvolatile ("1: fwait\n" +"2:\n" + _ASM_EXTABLE(1b, 2b));task_thread_info (tsk)->status &= ~TS_USEDFPU ;stts (); }
PATCH 4/12 x86: Merge __save_init_fpu()
In reply to Brian Gerst__save_init_fpu() is identical for 32-bit and 64-bit.
--- arch/x86/include/asm/i387.h | 11 ++--------- 1 files changed, 2 insertions(+), 9 deletions(-)
arch/x86/include/asm/i387.h +2 -9
@@ -197,12 +197,6 @@ static inline void fpu_save_init(struct fpu *fpu) fpu_clear(fpu); } -static inline void __save_init_fpu (struct task_struct *tsk) -{ -fpu_save_init (&tsk->thread.fpu); -task_thread_info (tsk)->status &= ~TS_USEDFPU ; -} -#else /* CONFIG_X86_32 */ #ifdef CONFIG_MATH_EMULATION
@@ -285,15 +279,14 @@ end: ; } +#endif /* CONFIG_X86_64 */ +static inline void __save_init_fpu (struct task_struct *tsk) {fpu_save_init (&tsk->thread.fpu);task_thread_info (tsk)->status &= ~TS_USEDFPU ; } - -#endif /* CONFIG_X86_64 */ -static inline int fpu_fxrstor_checking (struct fpu *fpu) {return fxrstor_checking (&fpu->state->fxsave);
Signature · 1 line
1.7.2.2
Re: [PATCH 04/12] x86: Merge __save_init_fpu()
Quoted 3 lines · Brian Gerst
__save_init_fpu()is identical for 32-bit and 64-bit.Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86, fpu: Merge __save_init_fpu()
In reply to Brian GerstCommit-ID: bfd946cb891800d408decaae268a3480775178a3 Gitweb: http://git.kernel.org/tip/bfd946cb891800d408decaae268a3480775178a3 Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:11 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:16:30 -0700
x86, fpu: Merge __save_init_fpu()
__save_init_fpu() is identical for 32-bit and 64-bit.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 11 ++--------- 1 files changed, 2 insertions(+), 9 deletions(-)
arch/x86/include/asm/i387.h +2 -9
@@ -197,12 +197,6 @@ static inline void fpu_save_init(struct fpu *fpu) fpu_clear(fpu); } -static inline void __save_init_fpu (struct task_struct *tsk) -{ -fpu_save_init (&tsk->thread.fpu); -task_thread_info (tsk)->status &= ~TS_USEDFPU ; -} -#else /* CONFIG_X86_32 */ #ifdef CONFIG_MATH_EMULATION
@@ -285,15 +279,14 @@ end: ; } +#endif /* CONFIG_X86_64 */ +static inline void __save_init_fpu (struct task_struct *tsk) {fpu_save_init (&tsk->thread.fpu);task_thread_info (tsk)->status &= ~TS_USEDFPU ; } - -#endif /* CONFIG_X86_64 */ -static inline int fpu_fxrstor_checking (struct fpu *fpu) {return fxrstor_checking (&fpu->state->fxsave);
PATCH 5/12 x86-64: Disable preemption when using TS_USEDFPU
In reply to Brian GerstConsolidates code and fixes the below race for 64-bit.
commit 9fa2f37bfeb798728241cc4a19578ce6e4258f25
Author: torvalds <torvalds> Date: Tue Sep 2 07:37:25 2003 +0000
Be a lot more careful about TS_USEDFPU and preemption
We had some races where we testecd (or set) TS_USEDFPU together with sequences that depended on the setting (like clearing or setting the TS flag in %cr0) and we could be preempted in between, which screws up the FPU state, since preemption will itself change USEDFPU and the TS flag.
This makes it a lot more explicit: the "internal" low-level FPU functions ("__xxxx_fpu()") all require preemption to be disabled, and the exported "real" functions will make sure that is the case.
One case - in __switch_to() - was switched to the non-preempt-safe internal version, since the scheduler itself has already disabled preemption.
BKrev: 3f5448b5WRiQuyzAlbajs3qoQjSobw
--- arch/x86/include/asm/i387.h | 15 --------------- arch/x86/kernel/process_64.c | 2 +- 2 files changed, 1 insertions(+), 16 deletions(-)
arch/x86/include/asm/i387.h +0 -15
@@ -387,19 +387,6 @@ static inline void irq_ts_restore(int TS_state)stts (); } -#ifdef CONFIG_X86_64 - -static inline void save_init_fpu (struct task_struct *tsk) -{ -__save_init_fpu (tsk); -stts (); -} - -#define unlazy_fpu __unlazy_fpu -#define clear_fpu __clear_fpu - -#else /* CONFIG_X86_32 */ -/* * These disable preemption on their own and are safe */
@@ -425,8 +412,6 @@ static inline void clear_fpu(struct task_struct *tsk)preempt_enable (); } -#endif /* CONFIG_X86_64 */ -/* * i387 state interaction */
arch/x86/kernel/process_64.c +1 -1
@@ -424,7 +424,7 @@ __switch_to(struct task_struct *prev_p, struct task_struct *next_p)load_TLS (next, cpu);/* Must be after DS reload */ -unlazy_fpu (prev_p); +__unlazy_fpu (prev_p);/* Make sure cpu is ready for new context */ if (preload_fpu)
Signature · 1 line
1.7.2.2
Re: [PATCH 05/12] x86-64: Disable preemption when using TS_USEDFPU
Quoted 18 lines · Brian Gerst
Consolidates code and fixes the below race for 64-bit.
commit
9fa2f37bfeb798728241cc4a19578ce6e4258f25Author: torvalds<torvalds> Date: Tue Sep 2 07:37:25 2003 +0000Be a lot more careful about
TS_USEDFPUand preemptionWe had some races where we testecd (or set)
TS_USEDFPUtogether with sequences that depended on the setting (like clearing or setting the TS flag in %cr0) and we could be preempted in between, which screws up the FPU state, since preemption will itself change USEDFPU and the TS flag.This makes it a lot more explicit: the "internal" low-level FPU functions ("
__xxxx_fpu()") all require preemption to be disabled, and the exported "real" functions will make sure that is the case.
Quoted 7 lines
One case - in
__switch_to()- was switched to the non-preempt-safe internal version, since the scheduler itself has already disabled preemption.BKrev: 3f5448b5WRiQuyzAlbajs3qoQjSobw
Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86-64, fpu: Disable preemption when using TS_USEDFPU
In reply to Brian GerstCommit-ID: a4d4fbc7735bba6654b20f859135f9d3f8fe7f76 Gitweb: http://git.kernel.org/tip/a4d4fbc7735bba6654b20f859135f9d3f8fe7f76 Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:12 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:16:45 -0700
x86-64, fpu: Disable preemption when using TS_USEDFPU
Consolidates code and fixes the below race for 64-bit.
commit 9fa2f37bfeb798728241cc4a19578ce6e4258f25
Author: torvalds <torvalds> Date: Tue Sep 2 07:37:25 2003 +0000
Be a lot more careful about TS_USEDFPU and preemption
We had some races where we testecd (or set) TS_USEDFPU together with sequences that depended on the setting (like clearing or setting the TS flag in %cr0) and we could be preempted in between, which screws up the FPU state, since preemption will itself change USEDFPU and the TS flag.
This makes it a lot more explicit: the "internal" low-level FPU functions ("__xxxx_fpu()") all require preemption to be disabled, and the exported "real" functions will make sure that is the case.
One case - in __switch_to() - was switched to the non-preempt-safe internal version, since the scheduler itself has already disabled preemption.
BKrev: 3f5448b5WRiQuyzAlbajs3qoQjSobw
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 15 --------------- arch/x86/kernel/process_64.c | 2 +- 2 files changed, 1 insertions(+), 16 deletions(-)
arch/x86/include/asm/i387.h +0 -15
@@ -387,19 +387,6 @@ static inline void irq_ts_restore(int TS_state)stts (); } -#ifdef CONFIG_X86_64 - -static inline void save_init_fpu (struct task_struct *tsk) -{ -__save_init_fpu (tsk); -stts (); -} - -#define unlazy_fpu __unlazy_fpu -#define clear_fpu __clear_fpu - -#else /* CONFIG_X86_32 */ -/* * These disable preemption on their own and are safe */
@@ -425,8 +412,6 @@ static inline void clear_fpu(struct task_struct *tsk)preempt_enable (); } -#endif /* CONFIG_X86_64 */ -/* * i387 state interaction */
arch/x86/kernel/process_64.c +1 -1
@@ -424,7 +424,7 @@ __switch_to(struct task_struct *prev_p, struct task_struct *next_p)load_TLS (next, cpu);/* Must be after DS reload */ -unlazy_fpu (prev_p); +__unlazy_fpu (prev_p);/* Make sure cpu is ready for new context */ if (preload_fpu)
PATCH 6/12 x86-64: Fix %cs value in convert_from_fxsr()
In reply to Brian GerstWhile %ds still contains the userspace selector, %cs is KERNEL_CS at this point. Always get %cs from pt_regs even for the current task.
--- arch/x86/kernel/i387.c | 18 ++++++++---------- 1 files changed, 8 insertions(+), 10 deletions(-)
arch/x86/kernel/i387.c +8 -10
@@ -384,19 +384,17 @@ convert_from_fxsr(struct user_i387_ia32_struct *env, struct task_struct *tsk)#ifdef CONFIG_X86_64 env->fip = fxsave->rip; env->foo = fxsave->rdp; +/* +* should be actually ds/cs at fpu exception time, but +* that information is not available in 64bit mode. +*/ + env->fcs =task_pt_regs (tsk)->cs;if (tsk == current) { -/* -* should be actually ds/cs at fpu exception time, but -* that information is not available in 64bit mode. -*/ - asm("mov %%ds, %[fos]" : [fos]"=r" (env->fos)); - asm("mov %%cs, %[fcs]" : [fcs]"=r" (env->fcs)); +savesegment (ds, env->fos); }else { -struct pt_regs *regs =task_pt_regs (tsk); - - env->fos =0xffff0000 | tsk->thread.ds; - env->fcs = regs->cs; + env->fos = tsk->thread.ds; } + env->fos |=0xffff0000 ;#else env->fip = fxsave->fip; env->fcs = (u16 ) fxsave->fcs | ((u32 ) fxsave->fop <<16 );
Signature · 1 line
1.7.2.2
Re: [PATCH 06/12] x86-64: Fix %cs value in convert_from_fxsr()
Quoted 4 lines · Brian Gerst
While %ds still contains the userspace selector, %cs is
KERNEL_CSat this point. Always get %cs frompt_regseven for the current task.Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86-64, fpu: Fix %cs value in convert_from_fxsr()
In reply to Brian GerstCommit-ID: 10c11f304986a1f84201c2261a428701f9d2dffc Gitweb: http://git.kernel.org/tip/10c11f304986a1f84201c2261a428701f9d2dffc Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:13 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:16:58 -0700
x86-64, fpu: Fix %cs value in convert_from_fxsr()
While %ds still contains the userspace selector, %cs is KERNEL_CS at this point. Always get %cs from pt_regs even for the current task.
LKML-Reference: <[email protected]>
--- arch/x86/kernel/i387.c | 18 ++++++++---------- 1 files changed, 8 insertions(+), 10 deletions(-)
arch/x86/kernel/i387.c +8 -10
@@ -389,19 +389,17 @@ convert_from_fxsr(struct user_i387_ia32_struct *env, struct task_struct *tsk)#ifdef CONFIG_X86_64 env->fip = fxsave->rip; env->foo = fxsave->rdp; +/* +* should be actually ds/cs at fpu exception time, but +* that information is not available in 64bit mode. +*/ + env->fcs =task_pt_regs (tsk)->cs;if (tsk == current) { -/* -* should be actually ds/cs at fpu exception time, but -* that information is not available in 64bit mode. -*/ - asm("mov %%ds, %[fos]" : [fos]"=r" (env->fos)); - asm("mov %%cs, %[fcs]" : [fcs]"=r" (env->fcs)); +savesegment (ds, env->fos); }else { -struct pt_regs *regs =task_pt_regs (tsk); - - env->fos =0xffff0000 | tsk->thread.ds; - env->fcs = regs->cs; + env->fos = tsk->thread.ds; } + env->fos |=0xffff0000 ;#else env->fip = fxsave->fip; env->fcs = (u16 ) fxsave->fcs | ((u32 ) fxsave->fop <<16 );
PATCH 7/12 x86-64: Simplify constraints for fxsave/fxtstor
In reply to Brian GerstUse the "R" constraint (legacy register) instead of listing all the possible registers. Clean up the comments as well.
--- arch/x86/include/asm/i387.h | 44 ++++++++++++++++-------------------------- 1 files changed, 17 insertions(+), 27 deletions(-)
arch/x86/include/asm/i387.h +17 -27
@@ -81,6 +81,7 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx) {int err; +/* See comment in fxsave() below. */ asmvolatile ("1: rex64/fxrstor (%[fx])\n\t" "2:\n" ".section .fixup,\"ax\"\n"
@@ -89,11 +90,7 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)".previous\n" _ASM_EXTABLE(1b ,3b ) : [err] "=r" (err) -#if 0 /* See comment in fxsave() below. */ - : [fx] "r" (fx), "m" (*fx), "0" (0)); -#else - : [fx] "cdaSDb" (fx), "m" (*fx), "0" (0)); -#endif + : [fx] "R" (fx), "m" (*fx), "0" (0));return err; }
@@ -140,6 +137,7 @@ static inline int fxsave_user(struct i387_fxsave_struct __user *fx)if (unlikely (err))return -EFAULT ; +/* See comment in fxsave() below. */ asmvolatile ("1: rex64/fxsave (%[fx])\n\t" "2:\n" ".section .fixup,\"ax\"\n"
@@ -148,11 +146,7 @@ static inline int fxsave_user(struct i387_fxsave_struct __user *fx)".previous\n" _ASM_EXTABLE(1b ,3b ) : [err] "=r" (err), "=m" (*fx) -#if 0 /* See comment in fxsave() below. */ - : [fx] "r" (fx), "0" (0)); -#else - : [fx] "cdaSDb" (fx), "0" (0)); -#endif + : [fx] "R" (fx), "0" (0));if (unlikely (err) &&__clear_user (fx,sizeof (struct i387_fxsave_struct ))) err = -EFAULT ;
@@ -165,26 +159,22 @@ static inline void fpu_fxsave(struct fpu *fpu)/* Using "rex64; fxsave %0" is broken because, if the memory operand uses any extended registers for addressing, a second REX prefix will be generated (to the assembler, rex64 followed by semicolon -is a separate instruction), and hence the 64-bitness is lost. */ -#if 0 -/* Using "fxsaveq %0" would be the ideal choice, but is only supported -starting with gas 2.16. */ - __asm__ __volatile__("fxsaveq %0" - :"=m" (fpu->state->fxsave)); -#elif 0 -/* Using, as a workaround, the properly prefixed form below isn't +is a separate instruction), and hence the 64-bitness is lost. +Using "fxsaveq %0" would be the ideal choice, but is only supported +starting with gas 2.16. +asm volatile("fxsaveq %0" +: "=m" (fpu->state->fxsave)); +Using, as a workaround, the properly prefixed form below isn't accepted by any binutils version so far released, complaining that the same type of prefix is used twice if an extended register is -needed for addressing (fix submitted to mainline 2005-11-21). */ - __asm__ __volatile__("rex64/fxsave %0" - :"=m" (fpu->state->fxsave)); -#else -/* This, however, we can work around by forcing the compiler to select +needed for addressing (fix submitted to mainline 2005-11-21). +asm volatile("rex64/fxsave %0" +: "=m" (fpu->state->fxsave)); +This, however, we can work around by forcing the compiler to select an addressing mode that doesn't require extended registers. */ - __asm__ __volatile__("rex64/fxsave (%1)" - :"=m" (fpu->state->fxsave) - :"cdaSDb" (&fpu->state->fxsave)); -#endif + asmvolatile ("rex64/fxsave (%[fx])" + :"=m" (fpu->state->fxsave) + : [fx]"R" (&fpu->state->fxsave)); }static inline void fpu_save_init (struct fpu *fpu)
Signature · 1 line
1.7.2.2
Re: [PATCH 07/12] x86-64: Simplify constraints for fxsave/fxtstor
Quoted 4 lines · Brian Gerst
Use the "R" constraint (legacy register) instead of listing all the possible registers. Clean up the comments as well.
Signed-off-by Brian Gerst<[email protected]>
H. Peter Anvin
reviewerRe: [PATCH 07/12] x86-64: Simplify constraints for fxsave/fxtstor
In reply to Brian GerstQuoted 4 lines · Brian Gerst
Use the "R" constraint (legacy register) instead of listing all the possible registers. Clean up the comments as well.
Signed-off-by Brian Gerst <[email protected]>
Hi Brian,
Have you tested this on *old* versions of gcc? Since the whole point of that butt-ugly code sequence is to support now-historic versions of binutils, we need to make sure that "R" was supposed on the corresponding gcc versions...
-hpa
Re: [PATCH 07/12] x86-64: Simplify constraints for fxsave/fxtstor
Quoted 4 lines · H. Peter Anvin
Quoted 3 lines · Brian Gerst
Use the "R" constraint (legacy register) instead of listing all the possible registers. Clean up the comments as well.
Quoted 8 lines
Quoted 1 line
Signed-off-by Brian Gerst <[email protected]>Hi Brian,
Have you tested this on *old* versions of gcc? Since the whole point of that butt-ugly code sequence is to support now-historic versions of binutils, we need to make sure that "R" was supposed on the corresponding gcc versions...
It's documented as far back as the GCC 3.1.1 manual. Whether it actually works or not on older compilers I have no way of testing.
--
Brian Gerst
[tip:x86/fpu] x86-64, fpu: Simplify constraints for fxsave/fxtstor
In reply to Brian GerstCommit-ID: 820241356d6aa9a895fc10def15794a5a5bfcd98 Gitweb: http://git.kernel.org/tip/820241356d6aa9a895fc10def15794a5a5bfcd98 Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:14 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:17:06 -0700
x86-64, fpu: Simplify constraints for fxsave/fxtstor
Use the "R" constraint (legacy register) instead of listing all the possible registers. Clean up the comments as well.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 44 ++++++++++++++++-------------------------- 1 files changed, 17 insertions(+), 27 deletions(-)
arch/x86/include/asm/i387.h +17 -27
@@ -81,6 +81,7 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx) {int err; +/* See comment in fxsave() below. */ asmvolatile ("1: rex64/fxrstor (%[fx])\n\t" "2:\n" ".section .fixup,\"ax\"\n"
@@ -89,11 +90,7 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)".previous\n" _ASM_EXTABLE(1b ,3b ) : [err] "=r" (err) -#if 0 /* See comment in fxsave() below. */ - : [fx] "r" (fx), "m" (*fx), "0" (0)); -#else - : [fx] "cdaSDb" (fx), "m" (*fx), "0" (0)); -#endif + : [fx] "R" (fx), "m" (*fx), "0" (0));return err; }
@@ -140,6 +137,7 @@ static inline int fxsave_user(struct i387_fxsave_struct __user *fx)if (unlikely (err))return -EFAULT ; +/* See comment in fxsave() below. */ asmvolatile ("1: rex64/fxsave (%[fx])\n\t" "2:\n" ".section .fixup,\"ax\"\n"
@@ -148,11 +146,7 @@ static inline int fxsave_user(struct i387_fxsave_struct __user *fx)".previous\n" _ASM_EXTABLE(1b ,3b ) : [err] "=r" (err), "=m" (*fx) -#if 0 /* See comment in fxsave() below. */ - : [fx] "r" (fx), "0" (0)); -#else - : [fx] "cdaSDb" (fx), "0" (0)); -#endif + : [fx] "R" (fx), "0" (0));if (unlikely (err) &&__clear_user (fx,sizeof (struct i387_fxsave_struct ))) err = -EFAULT ;
@@ -165,26 +159,22 @@ static inline void fpu_fxsave(struct fpu *fpu)/* Using "rex64; fxsave %0" is broken because, if the memory operand uses any extended registers for addressing, a second REX prefix will be generated (to the assembler, rex64 followed by semicolon -is a separate instruction), and hence the 64-bitness is lost. */ -#if 0 -/* Using "fxsaveq %0" would be the ideal choice, but is only supported -starting with gas 2.16. */ - __asm__ __volatile__("fxsaveq %0" - :"=m" (fpu->state->fxsave)); -#elif 0 -/* Using, as a workaround, the properly prefixed form below isn't +is a separate instruction), and hence the 64-bitness is lost. +Using "fxsaveq %0" would be the ideal choice, but is only supported +starting with gas 2.16. +asm volatile("fxsaveq %0" +: "=m" (fpu->state->fxsave)); +Using, as a workaround, the properly prefixed form below isn't accepted by any binutils version so far released, complaining that the same type of prefix is used twice if an extended register is -needed for addressing (fix submitted to mainline 2005-11-21). */ - __asm__ __volatile__("rex64/fxsave %0" - :"=m" (fpu->state->fxsave)); -#else -/* This, however, we can work around by forcing the compiler to select +needed for addressing (fix submitted to mainline 2005-11-21). +asm volatile("rex64/fxsave %0" +: "=m" (fpu->state->fxsave)); +This, however, we can work around by forcing the compiler to select an addressing mode that doesn't require extended registers. */ - __asm__ __volatile__("rex64/fxsave (%1)" - :"=m" (fpu->state->fxsave) - :"cdaSDb" (&fpu->state->fxsave)); -#endif + asmvolatile ("rex64/fxsave (%[fx])" + :"=m" (fpu->state->fxsave) + : [fx]"R" (&fpu->state->fxsave)); }static inline void fpu_save_init (struct fpu *fpu)
PATCH 8/12 x86-32: Remove math_emulate stub
In reply to Brian Gerstcheck_fpu() in bugs.c halts boot if no FPU is found and math emulation isn't enabled. Therefore this stub will never be used.
--- arch/x86/kernel/traps.c | 23 ++++++----------------- 1 files changed, 6 insertions(+), 17 deletions(-)
arch/x86/kernel/traps.c +6 -17
@@ -776,21 +776,10 @@ asmlinkage void math_state_restore(void) }EXPORT_SYMBOL_GPL (math_state_restore); -#ifndef CONFIG_MATH_EMULATION -void math_emulate (struct math_emu_info *info) -{ -printk (KERN_EMERG -"math-emulation not enabled and no coprocessor found.\n" ); -printk (KERN_EMERG "killing %s.\n" , current->comm); -force_sig (SIGFPE , current); -schedule (); -} -#endif /* CONFIG_MATH_EMULATION */ - dotraplinkage void __kprobesdo_device_not_available (struct pt_regs *regs,long error_code) { -#ifdef CONFIG_X86_32 +#ifdef CONFIG_MATH_EMULATION if (read_cr0 () &X86_CR0_EM ) {struct math_emu_info info = { };
@@ -798,12 +787,12 @@ do_device_not_available(struct pt_regs *regs, long error_code) info.regs = regs;math_emulate (&info); - }else { -math_state_restore ();/* interrupts still off */ -conditional_sti (regs); + return; } -#else -math_state_restore (); +#endif +math_state_restore ();/* interrupts still off */ +#ifdef CONFIG_X86_32 +conditional_sti (regs);#endif }
Signature · 1 line
1.7.2.2
Re: [PATCH 08/12] x86-32: Remove math_emulate stub
Quoted 4 lines · Brian Gerst
check_fpu()inbugs.chalts boot if no FPU is found and math emulation isn't enabled. Therefore this stub will never be used.Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86-32, fpu: Remove math_emulate stub
In reply to Brian GerstCommit-ID: a334fe43d85f570ae907acf988a053c5eff78d6e Gitweb: http://git.kernel.org/tip/a334fe43d85f570ae907acf988a053c5eff78d6e Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:15 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:17:11 -0700
x86-32, fpu: Remove math_emulate stub
check_fpu() in bugs.c halts boot if no FPU is found and math emulation isn't enabled. Therefore this stub will never be used.
LKML-Reference: <[email protected]>
--- arch/x86/kernel/traps.c | 23 ++++++----------------- 1 files changed, 6 insertions(+), 17 deletions(-)
arch/x86/kernel/traps.c +6 -17
@@ -776,21 +776,10 @@ asmlinkage void math_state_restore(void) }EXPORT_SYMBOL_GPL (math_state_restore); -#ifndef CONFIG_MATH_EMULATION -void math_emulate (struct math_emu_info *info) -{ -printk (KERN_EMERG -"math-emulation not enabled and no coprocessor found.\n" ); -printk (KERN_EMERG "killing %s.\n" , current->comm); -force_sig (SIGFPE , current); -schedule (); -} -#endif /* CONFIG_MATH_EMULATION */ - dotraplinkage void __kprobesdo_device_not_available (struct pt_regs *regs,long error_code) { -#ifdef CONFIG_X86_32 +#ifdef CONFIG_MATH_EMULATION if (read_cr0 () &X86_CR0_EM ) {struct math_emu_info info = { };
@@ -798,12 +787,12 @@ do_device_not_available(struct pt_regs *regs, long error_code) info.regs = regs;math_emulate (&info); - }else { -math_state_restore ();/* interrupts still off */ -conditional_sti (regs); + return; } -#else -math_state_restore (); +#endif +math_state_restore ();/* interrupts still off */ +#ifdef CONFIG_X86_32 +conditional_sti (regs);#endif }
PATCH 9/12 x86: Remove unnecessary ifdefs from i387 code.
In reply to Brian GerstRemove ifdefs for code that the compiler can optimize away on 64-bit.
--- arch/x86/include/asm/i387.h | 12 ++++++------ arch/x86/kernel/i387.c | 4 ---- 2 files changed, 6 insertions(+), 10 deletions(-)
arch/x86/include/asm/i387.h +6 -6
@@ -55,6 +55,12 @@ extern int save_i387_xstate_ia32(void __user *buf);extern int restore_i387_xstate_ia32 (void __user *buf);#endif +#ifdef CONFIG_MATH_EMULATION +extern void finit_soft_fpu (struct i387_soft_struct *soft); +#else +static inline void finit_soft_fpu (struct i387_soft_struct *soft) {} +#endif +#define X87_FSW_ES (1 << 7)/* Exception Summary */ static __always_inline __pure bool use_xsaveopt(void)
@@ -189,12 +195,6 @@ static inline void fpu_save_init(struct fpu *fpu)#else /* CONFIG_X86_32 */ -#ifdef CONFIG_MATH_EMULATION -extern void finit_soft_fpu (struct i387_soft_struct *soft); -#else -static inline void finit_soft_fpu (struct i387_soft_struct *soft) {} -#endif -/* perform fxrstor iff the processor has extended states, otherwise frstor */ static inline int fxrstor_checking (struct i387_fxsave_struct *fx) {
arch/x86/kernel/i387.c +0 -4
@@ -74,10 +74,8 @@ static void __cpuinit init_thread_xstate(void)if (cpu_has_fxsr) xstate_size =sizeof (struct i387_fxsave_struct ); -#ifdef CONFIG_X86_32 else xstate_size =sizeof (struct i387_fsave_struct ); -#endif }/*
@@ -114,12 +112,10 @@ void __cpuinit fpu_init(void)void fpu_finit (struct fpu *fpu) { -#ifdef CONFIG_X86_32 if (!HAVE_HWFP ) {finit_soft_fpu (&fpu->state->soft);return ; } -#endif if (cpu_has_fxsr) {struct i387_fxsave_struct *fx = &fpu->state->fxsave;
Signature · 1 line
1.7.2.2
Re: [PATCH 09/12] x86: Remove unnecessary ifdefs from i387 code.
Quoted 3 lines · Brian Gerst
Remove ifdefs for code that the compiler can optimize away on 64-bit.
Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86, fpu: Remove unnecessary ifdefs from i387 code.
In reply to Brian GerstCommit-ID: 8eb91a577d7763d21628f6761045328784b1911c Gitweb: http://git.kernel.org/tip/8eb91a577d7763d21628f6761045328784b1911c Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:16 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:17:18 -0700
x86, fpu: Remove unnecessary ifdefs from i387 code.
Remove ifdefs for code that the compiler can optimize away on 64-bit.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 12 ++++++------ arch/x86/kernel/i387.c | 4 ---- 2 files changed, 6 insertions(+), 10 deletions(-)
arch/x86/include/asm/i387.h +6 -6
@@ -55,6 +55,12 @@ extern int save_i387_xstate_ia32(void __user *buf);extern int restore_i387_xstate_ia32 (void __user *buf);#endif +#ifdef CONFIG_MATH_EMULATION +extern void finit_soft_fpu (struct i387_soft_struct *soft); +#else +static inline void finit_soft_fpu (struct i387_soft_struct *soft) {} +#endif +#define X87_FSW_ES (1 << 7)/* Exception Summary */ static __always_inline __pure bool use_xsaveopt(void)
@@ -189,12 +195,6 @@ static inline void fpu_save_init(struct fpu *fpu)#else /* CONFIG_X86_32 */ -#ifdef CONFIG_MATH_EMULATION -extern void finit_soft_fpu (struct i387_soft_struct *soft); -#else -static inline void finit_soft_fpu (struct i387_soft_struct *soft) {} -#endif -/* perform fxrstor iff the processor has extended states, otherwise frstor */ static inline int fxrstor_checking (struct i387_fxsave_struct *fx) {
arch/x86/kernel/i387.c +0 -4
@@ -79,10 +79,8 @@ static void __cpuinit init_thread_xstate(void)if (cpu_has_fxsr) xstate_size =sizeof (struct i387_fxsave_struct ); -#ifdef CONFIG_X86_32 else xstate_size =sizeof (struct i387_fsave_struct ); -#endif }/*
@@ -119,12 +117,10 @@ void __cpuinit fpu_init(void)void fpu_finit (struct fpu *fpu) { -#ifdef CONFIG_X86_32 if (!HAVE_HWFP ) {finit_soft_fpu (&fpu->state->soft);return ; } -#endif if (cpu_has_fxsr) {struct i387_fxsave_struct *fx = &fpu->state->fxsave;
PATCH 10/12 x86: Remove PSHUFB_XMM5_* macros
In reply to Brian GerstThe PSHUFB_XMM5_* macros are no longer used.
--- arch/x86/include/asm/i387.h | 3 --- 1 files changed, 0 insertions(+), 3 deletions(-)
arch/x86/include/asm/i387.h +0 -3
@@ -465,7 +465,4 @@ extern void fpu_finit(struct fpu *fpu);#endif /* __ASSEMBLY__ */ -#define PSHUFB_XMM5_XMM0 .byte 0x66, 0x0f, 0x38, 0x00, 0xc5 -#define PSHUFB_XMM5_XMM6 .byte 0x66, 0x0f, 0x38, 0x00, 0xf5 -#endif /* _ASM_X86_I387_H */
Signature · 1 line
1.7.2.2
Re: [PATCH 10/12] x86: Remove PSHUFB_XMM5_* macros
Quoted 3 lines · Brian Gerst
The PSHUFB_XMM5_* macros are no longer used.
Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86, fpu: Remove PSHUFB_XMM5_* macros
In reply to Brian GerstCommit-ID: eec73f813ab0954253e5e2168119c4555f83f07d Gitweb: http://git.kernel.org/tip/eec73f813ab0954253e5e2168119c4555f83f07d Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:17 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:17:25 -0700
x86, fpu: Remove PSHUFB_XMM5_* macros
The PSHUFB_XMM5_* macros are no longer used.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 3 --- 1 files changed, 0 insertions(+), 3 deletions(-)
arch/x86/include/asm/i387.h +0 -3
@@ -465,7 +465,4 @@ extern void fpu_finit(struct fpu *fpu);#endif /* __ASSEMBLY__ */ -#define PSHUFB_XMM5_XMM0 .byte 0x66, 0x0f, 0x38, 0x00, 0xc5 -#define PSHUFB_XMM5_XMM6 .byte 0x66, 0x0f, 0x38, 0x00, 0xf5 -#endif /* _ASM_X86_I387_H */
PATCH 11/12 x86-32: Rewrite fpu_save_init()
In reply to Brian GerstRewrite fpu_save_init() to prepare for merging with 64-bit.
--- arch/x86/include/asm/i387.h | 47 ++++++++++++++++++++---------------------- 1 files changed, 22 insertions(+), 25 deletions(-)
arch/x86/include/asm/i387.h +22 -25
@@ -73,6 +73,11 @@ static __always_inline __pure bool use_xsave(void)return static_cpu_has (X86_FEATURE_XSAVE ); } +static __always_inline __pure bool use_fxsr(void) +{ +return static_cpu_has (X86_FEATURE_FXSR ); +} +extern void __sanitize_i387_state (struct task_struct *);static inline void sanitize_i387_state (struct task_struct *tsk)
@@ -211,6 +216,12 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)return 0 ; } +static inline void fpu_fxsave (struct fpu *fpu) +{ + asmvolatile ("fxsave %[fx]" + : [fx]"=m" (fpu->state->fxsave)); +} +/* We need a safe address that is cheap to find and that is already in L1 during context switch. The best choices are unfortunately different for UP and SMP */
@@ -226,36 +237,24 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)static inline void fpu_save_init (struct fpu *fpu) {if (use_xsave ()) { - struct xsave_struct *xstate = &fpu->state->xsave; - struct i387_fxsave_struct *fx = &fpu->state->fxsave; -fpu_xsave (fpu);/* * xsave header may indicate the init state of the FP. */ - if (!(xstate->xsave_hdr.xstate_bv & XSTATE_FP)) - goto end; - - if (unlikely(fx->swd & X87_FSW_ES)) - asm volatile("fnclex"); - - /* - * we can do a simple return here or be paranoid :) - */ - goto clear_state; +if (!(fpu->state->xsave.xsave_hdr.xstate_bv &XSTATE_FP )) +return ; + }else if (use_fxsr ()) { +fpu_fxsave (fpu); + }else { + asmvolatile ("fsave %[fx]; fwait" + : [fx]"=m" (fpu->state->fsave)); +return ; } - /* Use more nops than strictly needed in case the compiler - varies code */ - alternative_input( - "fnsave %[fx] ;fwait;" GENERIC_NOP8 GENERIC_NOP4, - "fxsave %[fx]\n" - "bt $7,%[fsw] ; jnc 1f ; fnclex\n1:", - X86_FEATURE_FXSR, - [fx] "m" (fpu->state->fxsave), - [fsw] "m" (fpu->state->fxsave.swd) : "memory"); -clear_state: +if (unlikely (fpu->state->fxsave.swd &X87_FSW_ES )) + asmvolatile ("fnclex" ); +/* AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is pending. Clear the x87 state here by setting it to fixed values. safe_address is a random variable that should be in L1 */
@@ -265,8 +264,6 @@ clear_state:"fildl %[addr]" ,/* set F?P to defined value */ X86_FEATURE_FXSAVE_LEAK, [addr] "m" (safe_address)); -end: - ; }#endif /* CONFIG_X86_64 */
Signature · 1 line
1.7.2.2
Re: [PATCH 11/12] x86-32: Rewrite fpu_save_init()
Quoted 3 lines · Brian Gerst
Rewrite
fpu_save_init()to prepare for merging with 64-bit.Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86-32, fpu: Rewrite fpu_save_init()
In reply to Brian GerstCommit-ID: 58a992b9cbaf449aeebd3575c3695a9eb5d95b5e Gitweb: http://git.kernel.org/tip/58a992b9cbaf449aeebd3575c3695a9eb5d95b5e Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:18 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:17:31 -0700
x86-32, fpu: Rewrite fpu_save_init()
Rewrite fpu_save_init() to prepare for merging with 64-bit.
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 47 ++++++++++++++++++++---------------------- 1 files changed, 22 insertions(+), 25 deletions(-)
arch/x86/include/asm/i387.h +22 -25
@@ -73,6 +73,11 @@ static __always_inline __pure bool use_xsave(void)return static_cpu_has (X86_FEATURE_XSAVE ); } +static __always_inline __pure bool use_fxsr(void) +{ +return static_cpu_has (X86_FEATURE_FXSR ); +} +extern void __sanitize_i387_state (struct task_struct *);static inline void sanitize_i387_state (struct task_struct *tsk)
@@ -211,6 +216,12 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)return 0 ; } +static inline void fpu_fxsave (struct fpu *fpu) +{ + asmvolatile ("fxsave %[fx]" + : [fx]"=m" (fpu->state->fxsave)); +} +/* We need a safe address that is cheap to find and that is already in L1 during context switch. The best choices are unfortunately different for UP and SMP */
@@ -226,36 +237,24 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)static inline void fpu_save_init (struct fpu *fpu) {if (use_xsave ()) { - struct xsave_struct *xstate = &fpu->state->xsave; - struct i387_fxsave_struct *fx = &fpu->state->fxsave; -fpu_xsave (fpu);/* * xsave header may indicate the init state of the FP. */ - if (!(xstate->xsave_hdr.xstate_bv & XSTATE_FP)) - goto end; - - if (unlikely(fx->swd & X87_FSW_ES)) - asm volatile("fnclex"); - - /* - * we can do a simple return here or be paranoid :) - */ - goto clear_state; +if (!(fpu->state->xsave.xsave_hdr.xstate_bv &XSTATE_FP )) +return ; + }else if (use_fxsr ()) { +fpu_fxsave (fpu); + }else { + asmvolatile ("fsave %[fx]; fwait" + : [fx]"=m" (fpu->state->fsave)); +return ; } - /* Use more nops than strictly needed in case the compiler - varies code */ - alternative_input( - "fnsave %[fx] ;fwait;" GENERIC_NOP8 GENERIC_NOP4, - "fxsave %[fx]\n" - "bt $7,%[fsw] ; jnc 1f ; fnclex\n1:", - X86_FEATURE_FXSR, - [fx] "m" (fpu->state->fxsave), - [fsw] "m" (fpu->state->fxsave.swd) : "memory"); -clear_state: +if (unlikely (fpu->state->fxsave.swd &X87_FSW_ES )) + asmvolatile ("fnclex" ); +/* AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is pending. Clear the x87 state here by setting it to fixed values. safe_address is a random variable that should be in L1 */
@@ -265,8 +264,6 @@ clear_state:"fildl %[addr]" ,/* set F?P to defined value */ X86_FEATURE_FXSAVE_LEAK, [addr] "m" (safe_address)); -end: - ; }#endif /* CONFIG_X86_64 */
PATCH 12/12 x86: Merge fpu_save_init()
In reply to Brian GerstMake 64-bit use the 32-bit version of fpu_save_init(). Remove unused clear_fpu_state().
--- arch/x86/include/asm/i387.h | 48 +++--------------------------------------- 1 files changed, 4 insertions(+), 44 deletions(-)
arch/x86/include/asm/i387.h +4 -44
@@ -105,36 +105,6 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)return err; } -/* AMD CPUs don't save/restore FDP/FIP/FOP unless an exception -is pending. Clear the x87 state here by setting it to fixed -values. The kernel data segment can be sometimes 0 and sometimes -new user value. Both should be ok. -Use the PDA as safe address because it should be already in L1. */ -static inline void fpu_clear (struct fpu *fpu) -{ -struct xsave_struct *xstate = &fpu->state->xsave; -struct i387_fxsave_struct *fx = &fpu->state->fxsave; - -/* -* xsave header may indicate the init state of the FP. -*/ -if (use_xsave () && - !(xstate->xsave_hdr.xstate_bv &XSTATE_FP )) -return ; - -if (unlikely (fx->swd &X87_FSW_ES )) - asmvolatile ("fnclex" ); - alternative_input(ASM_NOP8 ASM_NOP2, -" emms\n" /* clear stack tags */ -" fildl %%gs:0" ,/* load to clear state */ - X86_FEATURE_FXSAVE_LEAK); -} - -static inline void clear_fpu_state (struct task_struct *tsk) -{ -fpu_clear (&tsk->thread.fpu); -} -static inline int fxsave_user (struct i387_fxsave_struct __user *fx) {int err;
@@ -188,16 +158,6 @@ static inline void fpu_fxsave(struct fpu *fpu) : [fx] "R" (&fpu->state->fxsave)); } -static inline void fpu_save_init (struct fpu *fpu) -{ -if (use_xsave ()) -fpu_xsave (fpu); -else -fpu_fxsave (fpu); - -fpu_clear (fpu); -} -#else /* CONFIG_X86_32 */ /* perform fxrstor iff the processor has extended states, otherwise frstor */
@@ -222,6 +182,8 @@ static inline void fpu_fxsave(struct fpu *fpu) : [fx] "=m" (fpu->state->fxsave)); } +#endif /* CONFIG_X86_64 */ +/* We need a safe address that is cheap to find and that is already in L1 during context switch. The best choices are unfortunately different for UP and SMP */
@@ -259,15 +221,13 @@ static inline void fpu_save_init(struct fpu *fpu)is pending. Clear the x87 state here by setting it to fixed values. safe_address is a random variable that should be in L1 */ alternative_input( - GENERIC_NOP8 GENERIC_NOP2, + ASM_NOP8 ASM_NOP2,"emms\n\t" /* clear stack tags */ -"fildl %[addr]" ,/* set F?P to defined value */ +"fildl %P[addr]" ,/* set F?P to defined value */ X86_FEATURE_FXSAVE_LEAK, [addr] "m" (safe_address)); } -#endif /* CONFIG_X86_64 */ -static inline void __save_init_fpu (struct task_struct *tsk) {fpu_save_init (&tsk->thread.fpu);
Signature · 1 line
1.7.2.2
Re: [PATCH 12/12] x86: Merge fpu_save_init()
Quoted 4 lines · Brian Gerst
Make 64-bit use the 32-bit version of
fpu_save_init(). Remove unusedclear_fpu_state().Signed-off-by Brian Gerst<[email protected]>
[tip:x86/fpu] x86, fpu: Merge fpu_save_init()
In reply to Brian GerstCommit-ID: b2b57fe053c9cf8b8af5a0e826a465996afed0ff Gitweb: http://git.kernel.org/tip/b2b57fe053c9cf8b8af5a0e826a465996afed0ff Author: Brian Gerst <[email protected]> AuthorDate: Fri, 3 Sep 2010 21:17:19 -0400 Committer: H. Peter Anvin <[email protected]> CommitDate: Thu, 9 Sep 2010 14:17:36 -0700
x86, fpu: Merge fpu_save_init()
Make 64-bit use the 32-bit version of fpu_save_init(). Remove unused clear_fpu_state().
LKML-Reference: <[email protected]>
--- arch/x86/include/asm/i387.h | 48 +++--------------------------------------- 1 files changed, 4 insertions(+), 44 deletions(-)
arch/x86/include/asm/i387.h +4 -44
@@ -105,36 +105,6 @@ static inline int fxrstor_checking(struct i387_fxsave_struct *fx)return err; } -/* AMD CPUs don't save/restore FDP/FIP/FOP unless an exception -is pending. Clear the x87 state here by setting it to fixed -values. The kernel data segment can be sometimes 0 and sometimes -new user value. Both should be ok. -Use the PDA as safe address because it should be already in L1. */ -static inline void fpu_clear (struct fpu *fpu) -{ -struct xsave_struct *xstate = &fpu->state->xsave; -struct i387_fxsave_struct *fx = &fpu->state->fxsave; - -/* -* xsave header may indicate the init state of the FP. -*/ -if (use_xsave () && - !(xstate->xsave_hdr.xstate_bv &XSTATE_FP )) -return ; - -if (unlikely (fx->swd &X87_FSW_ES )) - asmvolatile ("fnclex" ); - alternative_input(ASM_NOP8 ASM_NOP2, -" emms\n" /* clear stack tags */ -" fildl %%gs:0" ,/* load to clear state */ - X86_FEATURE_FXSAVE_LEAK); -} - -static inline void clear_fpu_state (struct task_struct *tsk) -{ -fpu_clear (&tsk->thread.fpu); -} -static inline int fxsave_user (struct i387_fxsave_struct __user *fx) {int err;
@@ -188,16 +158,6 @@ static inline void fpu_fxsave(struct fpu *fpu) : [fx] "R" (&fpu->state->fxsave)); } -static inline void fpu_save_init (struct fpu *fpu) -{ -if (use_xsave ()) -fpu_xsave (fpu); -else -fpu_fxsave (fpu); - -fpu_clear (fpu); -} -#else /* CONFIG_X86_32 */ /* perform fxrstor iff the processor has extended states, otherwise frstor */
@@ -222,6 +182,8 @@ static inline void fpu_fxsave(struct fpu *fpu) : [fx] "=m" (fpu->state->fxsave)); } +#endif /* CONFIG_X86_64 */ +/* We need a safe address that is cheap to find and that is already in L1 during context switch. The best choices are unfortunately different for UP and SMP */
@@ -259,15 +221,13 @@ static inline void fpu_save_init(struct fpu *fpu)is pending. Clear the x87 state here by setting it to fixed values. safe_address is a random variable that should be in L1 */ alternative_input( - GENERIC_NOP8 GENERIC_NOP2, + ASM_NOP8 ASM_NOP2,"emms\n\t" /* clear stack tags */ -"fildl %[addr]" ,/* set F?P to defined value */ +"fildl %P[addr]" ,/* set F?P to defined value */ X86_FEATURE_FXSAVE_LEAK, [addr] "m" (safe_address)); } -#endif /* CONFIG_X86_64 */ -static inline void __save_init_fpu (struct task_struct *tsk) {fpu_save_init (&tsk->thread.fpu);
Quoted 1 line · Brian Gerst
This patch set cleans up and merges the 32-bit and 64-bit FPU code.
Oh, you seem to have dropped all of my previous ACKs.