Use defined 16-bits ASC/ASCQ combinations

index c6b4a4dc8d9c..f742a3bfeb86 100644
@@ -12,6 +12,7 @@
 
 #include <linux/build_bug.h>
 #include <linux/types.h>
+#include <scsi/scsi_sense.h>
 
 /*
  *      SCSI opcodes

@@ -218,25 +219,6 @@ enum sam_status {
 
 #define STATUS_MASK         0xfe
 
-/*
- *  SENSE KEYS
- */
-#define NO_SENSE            0x00
-#define RECOVERED_ERROR     0x01
-#define NOT_READY           0x02
-#define MEDIUM_ERROR        0x03
-#define HARDWARE_ERROR      0x04
-#define ILLEGAL_REQUEST     0x05
-#define UNIT_ATTENTION      0x06
-#define DATA_PROTECT        0x07
-#define BLANK_CHECK         0x08
-#define VENDOR_SPECIFIC     0x09
-#define COPY_ABORTED        0x0a
-#define ABORTED_COMMAND     0x0b
-#define VOLUME_OVERFLOW     0x0d
-#define MISCOMPARE          0x0e
-#define COMPLETED	    0x0f
-
 /*
  * Additional Sense Codes (ASC).
  */

950 lines not on this page · raw message

index 805d4c13d070..c2eb1a9ec4c0 100644
@@ -4,876 +4,1642 @@
  * http://www.t10.org/lists/asc-num.txt [most recent: 20200817]
  */
 
-SENSE_CODE(0x0000, "No additional sense information")
-SENSE_CODE(0x0001, "Filemark detected")
-SENSE_CODE(0x0002, "End-of-partition/medium detected")
-SENSE_CODE(0x0003, "Setmark detected")
-SENSE_CODE(0x0004, "Beginning-of-partition/medium detected")
-SENSE_CODE(0x0005, "End-of-data detected")
-SENSE_CODE(0x0006, "I/O process terminated")
-SENSE_CODE(0x0007, "Programmable early warning detected")
-SENSE_CODE(0x0011, "Audio play operation in progress")
-SENSE_CODE(0x0012, "Audio play operation paused")
-SENSE_CODE(0x0013, "Audio play operation successfully completed")
-SENSE_CODE(0x0014, "Audio play operation stopped due to error")
-SENSE_CODE(0x0015, "No current audio status to return")
-SENSE_CODE(0x0016, "Operation in progress")
-SENSE_CODE(0x0017, "Cleaning requested")
-SENSE_CODE(0x0018, "Erase operation in progress")
-SENSE_CODE(0x0019, "Locate operation in progress")
-SENSE_CODE(0x001A, "Rewind operation in progress")
-SENSE_CODE(0x001B, "Set capacity operation in progress")
-SENSE_CODE(0x001C, "Verify operation in progress")
-SENSE_CODE(0x001D, "ATA pass through information available")
-SENSE_CODE(0x001E, "Conflicting SA creation request")
-SENSE_CODE(0x001F, "Logical unit transitioning to another power condition")
-SENSE_CODE(0x0020, "Extended copy information available")
-SENSE_CODE(0x0021, "Atomic command aborted due to ACA")
-SENSE_CODE(0x0022, "Deferred microcode is pending")
-
-SENSE_CODE(0x0100, "No index/sector signal")
-
-SENSE_CODE(0x0200, "No seek complete")
-
-SENSE_CODE(0x0300, "Peripheral device write fault")
-SENSE_CODE(0x0301, "No write current")
-SENSE_CODE(0x0302, "Excessive write errors")
-
-SENSE_CODE(0x0400, "Logical unit not ready, cause not reportable")
-SENSE_CODE(0x0401, "Logical unit is in process of becoming ready")
-SENSE_CODE(0x0402, "Logical unit not ready, initializing command required")
-SENSE_CODE(0x0403, "Logical unit not ready, manual intervention required")
-SENSE_CODE(0x0404, "Logical unit not ready, format in progress")
-SENSE_CODE(0x0405, "Logical unit not ready, rebuild in progress")
-SENSE_CODE(0x0406, "Logical unit not ready, recalculation in progress")
-SENSE_CODE(0x0407, "Logical unit not ready, operation in progress")
-SENSE_CODE(0x0408, "Logical unit not ready, long write in progress")
-SENSE_CODE(0x0409, "Logical unit not ready, self-test in progress")
-SENSE_CODE(0x040A, "Logical unit not accessible, asymmetric access state transition")
-SENSE_CODE(0x040B, "Logical unit not accessible, target port in standby state")
-SENSE_CODE(0x040C, "Logical unit not accessible, target port in unavailable state")
-SENSE_CODE(0x040D, "Logical unit not ready, structure check required")
-SENSE_CODE(0x040E, "Logical unit not ready, security session in progress")
-SENSE_CODE(0x0410, "Logical unit not ready, auxiliary memory not accessible")
-SENSE_CODE(0x0411, "Logical unit not ready, notify (enable spinup) required")
-SENSE_CODE(0x0412, "Logical unit not ready, offline")
-SENSE_CODE(0x0413, "Logical unit not ready, SA creation in progress")
-SENSE_CODE(0x0414, "Logical unit not ready, space allocation in progress")
-SENSE_CODE(0x0415, "Logical unit not ready, robotics disabled")
-SENSE_CODE(0x0416, "Logical unit not ready, configuration required")
-SENSE_CODE(0x0417, "Logical unit not ready, calibration required")
-SENSE_CODE(0x0418, "Logical unit not ready, a door is open")
-SENSE_CODE(0x0419, "Logical unit not ready, operating in sequential mode")
-SENSE_CODE(0x041A, "Logical unit not ready, start stop unit command in progress")
-SENSE_CODE(0x041B, "Logical unit not ready, sanitize in progress")
-SENSE_CODE(0x041C, "Logical unit not ready, additional power use not yet granted")
-SENSE_CODE(0x041D, "Logical unit not ready, configuration in progress")
-SENSE_CODE(0x041E, "Logical unit not ready, microcode activation required")
-SENSE_CODE(0x041F, "Logical unit not ready, microcode download required")
-SENSE_CODE(0x0420, "Logical unit not ready, logical unit reset required")
-SENSE_CODE(0x0421, "Logical unit not ready, hard reset required")
-SENSE_CODE(0x0422, "Logical unit not ready, power cycle required")
-SENSE_CODE(0x0423, "Logical unit not ready, affiliation required")
-SENSE_CODE(0x0424, "Depopulation in progress")
-SENSE_CODE(0x0425, "Depopulation restoration in progress")
-
-SENSE_CODE(0x0500, "Logical unit does not respond to selection")
-
-SENSE_CODE(0x0600, "No reference position found")
-
-SENSE_CODE(0x0700, "Multiple peripheral devices selected")
-
-SENSE_CODE(0x0800, "Logical unit communication failure")
-SENSE_CODE(0x0801, "Logical unit communication time-out")
-SENSE_CODE(0x0802, "Logical unit communication parity error")
-SENSE_CODE(0x0803, "Logical unit communication CRC error (Ultra-DMA/32)")
-SENSE_CODE(0x0804, "Unreachable copy target")
-
-SENSE_CODE(0x0900, "Track following error")
-SENSE_CODE(0x0901, "Tracking servo failure")
-SENSE_CODE(0x0902, "Focus servo failure")
-SENSE_CODE(0x0903, "Spindle servo failure")
-SENSE_CODE(0x0904, "Head select fault")
-SENSE_CODE(0x0905, "Vibration induced tracking error")
-
-SENSE_CODE(0x0A00, "Error log overflow")
-
-SENSE_CODE(0x0B00, "Warning")
-SENSE_CODE(0x0B01, "Warning - specified temperature exceeded")
-SENSE_CODE(0x0B02, "Warning - enclosure degraded")
-SENSE_CODE(0x0B03, "Warning - background self-test failed")
-SENSE_CODE(0x0B04, "Warning - background pre-scan detected medium error")
-SENSE_CODE(0x0B05, "Warning - background medium scan detected medium error")
-SENSE_CODE(0x0B06, "Warning - non-volatile cache now volatile")
-SENSE_CODE(0x0B07, "Warning - degraded power to non-volatile cache")
-SENSE_CODE(0x0B08, "Warning - power loss expected")
-SENSE_CODE(0x0B09, "Warning - device statistics notification active")
-SENSE_CODE(0x0B0A, "Warning - high critical temperature limit exceeded")
-SENSE_CODE(0x0B0B, "Warning - low critical temperature limit exceeded")
-SENSE_CODE(0x0B0C, "Warning - high operating temperature limit exceeded")
-SENSE_CODE(0x0B0D, "Warning - low operating temperature limit exceeded")
-SENSE_CODE(0x0B0E, "Warning - high critical humidity limit exceeded")
-SENSE_CODE(0x0B0F, "Warning - low critical humidity limit exceeded")
-SENSE_CODE(0x0B10, "Warning - high operating humidity limit exceeded")
-SENSE_CODE(0x0B11, "Warning - low operating humidity limit exceeded")
-SENSE_CODE(0x0B12, "Warning - microcode security at risk")
-SENSE_CODE(0x0B13, "Warning - microcode digital signature validation failure")
-SENSE_CODE(0x0B14, "Warning - physical element status change")
-
-SENSE_CODE(0x0C00, "Write error")
-SENSE_CODE(0x0C01, "Write error - recovered with auto reallocation")
-SENSE_CODE(0x0C02, "Write error - auto reallocation failed")
-SENSE_CODE(0x0C03, "Write error - recommend reassignment")
-SENSE_CODE(0x0C04, "Compression check miscompare error")
-SENSE_CODE(0x0C05, "Data expansion occurred during compression")
-SENSE_CODE(0x0C06, "Block not compressible")
-SENSE_CODE(0x0C07, "Write error - recovery needed")
-SENSE_CODE(0x0C08, "Write error - recovery failed")
-SENSE_CODE(0x0C09, "Write error - loss of streaming")
-SENSE_CODE(0x0C0A, "Write error - padding blocks added")
-SENSE_CODE(0x0C0B, "Auxiliary memory write error")
-SENSE_CODE(0x0C0C, "Write error - unexpected unsolicited data")
-SENSE_CODE(0x0C0D, "Write error - not enough unsolicited data")
-SENSE_CODE(0x0C0E, "Multiple write errors")
-SENSE_CODE(0x0C0F, "Defects in error window")
-SENSE_CODE(0x0C10, "Incomplete multiple atomic write operations")
-SENSE_CODE(0x0C11, "Write error - recovery scan needed")
-SENSE_CODE(0x0C12, "Write error - insufficient zone resources")
-
-SENSE_CODE(0x0D00, "Error detected by third party temporary initiator")
-SENSE_CODE(0x0D01, "Third party device failure")
-SENSE_CODE(0x0D02, "Copy target device not reachable")
-SENSE_CODE(0x0D03, "Incorrect copy target device type")
-SENSE_CODE(0x0D04, "Copy target device data underrun")
-SENSE_CODE(0x0D05, "Copy target device data overrun")
-
-SENSE_CODE(0x0E00, "Invalid information unit")
-SENSE_CODE(0x0E01, "Information unit too short")
-SENSE_CODE(0x0E02, "Information unit too long")
-SENSE_CODE(0x0E03, "Invalid field in command information unit")
-
-SENSE_CODE(0x1000, "Id CRC or ECC error")
-SENSE_CODE(0x1001, "Logical block guard check failed")
-SENSE_CODE(0x1002, "Logical block application tag check failed")
-SENSE_CODE(0x1003, "Logical block reference tag check failed")
-SENSE_CODE(0x1004, "Logical block protection error on recover buffered data")
-SENSE_CODE(0x1005, "Logical block protection method error")
-
-SENSE_CODE(0x1100, "Unrecovered read error")
-SENSE_CODE(0x1101, "Read retries exhausted")
-SENSE_CODE(0x1102, "Error too long to correct")
-SENSE_CODE(0x1103, "Multiple read errors")
-SENSE_CODE(0x1104, "Unrecovered read error - auto reallocate failed")
-SENSE_CODE(0x1105, "L-EC uncorrectable error")
-SENSE_CODE(0x1106, "CIRC unrecovered error")
-SENSE_CODE(0x1107, "Data re-synchronization error")
-SENSE_CODE(0x1108, "Incomplete block read")
-SENSE_CODE(0x1109, "No gap found")
-SENSE_CODE(0x110A, "Miscorrected error")
-SENSE_CODE(0x110B, "Unrecovered read error - recommend reassignment")
-SENSE_CODE(0x110C, "Unrecovered read error - recommend rewrite the data")
-SENSE_CODE(0x110D, "De-compression CRC error")
-SENSE_CODE(0x110E, "Cannot decompress using declared algorithm")
-SENSE_CODE(0x110F, "Error reading UPC/EAN number")
-SENSE_CODE(0x1110, "Error reading ISRC number")
-SENSE_CODE(0x1111, "Read error - loss of streaming")
-SENSE_CODE(0x1112, "Auxiliary memory read error")
-SENSE_CODE(0x1113, "Read error - failed retransmission request")
-SENSE_CODE(0x1114, "Read error - lba marked bad by application client")
-SENSE_CODE(0x1115, "Write after sanitize required")
-
-SENSE_CODE(0x1200, "Address mark not found for id field")
-
-SENSE_CODE(0x1300, "Address mark not found for data field")
-
-SENSE_CODE(0x1400, "Recorded entity not found")
-SENSE_CODE(0x1401, "Record not found")
-SENSE_CODE(0x1402, "Filemark or setmark not found")
-SENSE_CODE(0x1403, "End-of-data not found")
-SENSE_CODE(0x1404, "Block sequence error")
-SENSE_CODE(0x1405, "Record not found - recommend reassignment")
-SENSE_CODE(0x1406, "Record not found - data auto-reallocated")
-SENSE_CODE(0x1407, "Locate operation failure")
-
-SENSE_CODE(0x1500, "Random positioning error")
-SENSE_CODE(0x1501, "Mechanical positioning error")
-SENSE_CODE(0x1502, "Positioning error detected by read of medium")
-
-SENSE_CODE(0x1600, "Data synchronization mark error")
-SENSE_CODE(0x1601, "Data sync error - data rewritten")
-SENSE_CODE(0x1602, "Data sync error - recommend rewrite")
-SENSE_CODE(0x1603, "Data sync error - data auto-reallocated")
-SENSE_CODE(0x1604, "Data sync error - recommend reassignment")
-
-SENSE_CODE(0x1700, "Recovered data with no error correction applied")
-SENSE_CODE(0x1701, "Recovered data with retries")
-SENSE_CODE(0x1702, "Recovered data with positive head offset")
-SENSE_CODE(0x1703, "Recovered data with negative head offset")
-SENSE_CODE(0x1704, "Recovered data with retries and/or circ applied")
-SENSE_CODE(0x1705, "Recovered data using previous sector id")
-SENSE_CODE(0x1706, "Recovered data without ECC - data auto-reallocated")
-SENSE_CODE(0x1707, "Recovered data without ECC - recommend reassignment")
-SENSE_CODE(0x1708, "Recovered data without ECC - recommend rewrite")
-SENSE_CODE(0x1709, "Recovered data without ECC - data rewritten")
-
-SENSE_CODE(0x1800, "Recovered data with error correction applied")
-SENSE_CODE(0x1801, "Recovered data with error corr. & retries applied")
-SENSE_CODE(0x1802, "Recovered data - data auto-reallocated")
-SENSE_CODE(0x1803, "Recovered data with CIRC")
-SENSE_CODE(0x1804, "Recovered data with L-EC")
-SENSE_CODE(0x1805, "Recovered data - recommend reassignment")
-SENSE_CODE(0x1806, "Recovered data - recommend rewrite")
-SENSE_CODE(0x1807, "Recovered data with ECC - data rewritten")
-SENSE_CODE(0x1808, "Recovered data with linking")
-
-SENSE_CODE(0x1900, "Defect list error")
-SENSE_CODE(0x1901, "Defect list not available")
-SENSE_CODE(0x1902, "Defect list error in primary list")
-SENSE_CODE(0x1903, "Defect list error in grown list")
-
-SENSE_CODE(0x1A00, "Parameter list length error")
-
-SENSE_CODE(0x1B00, "Synchronous data transfer error")
-
-SENSE_CODE(0x1C00, "Defect list not found")
-SENSE_CODE(0x1C01, "Primary defect list not found")
-SENSE_CODE(0x1C02, "Grown defect list not found")
-
-SENSE_CODE(0x1D00, "Miscompare during verify operation")
-SENSE_CODE(0x1D01, "Miscompare verify of unmapped LBA")
-
-SENSE_CODE(0x1E00, "Recovered id with ECC correction")
-
-SENSE_CODE(0x1F00, "Partial defect list transfer")
-
-SENSE_CODE(0x2000, "Invalid command operation code")
-SENSE_CODE(0x2001, "Access denied - initiator pending-enrolled")
-SENSE_CODE(0x2002, "Access denied - no access rights")
-SENSE_CODE(0x2003, "Access denied - invalid mgmt id key")
-SENSE_CODE(0x2004, "Illegal command while in write capable state")
-SENSE_CODE(0x2005, "Obsolete")
-SENSE_CODE(0x2006, "Illegal command while in explicit address mode")
-SENSE_CODE(0x2007, "Illegal command while in implicit address mode")
-SENSE_CODE(0x2008, "Access denied - enrollment conflict")
-SENSE_CODE(0x2009, "Access denied - invalid LU identifier")
-SENSE_CODE(0x200A, "Access denied - invalid proxy token")
-SENSE_CODE(0x200B, "Access denied - ACL LUN conflict")
-SENSE_CODE(0x200C, "Illegal command when not in append-only mode")
-SENSE_CODE(0x200D, "Not an administrative logical unit")
-SENSE_CODE(0x200E, "Not a subsidiary logical unit")
-SENSE_CODE(0x200F, "Not a conglomerate logical unit")
-
-SENSE_CODE(0x2100, "Logical block address out of range")
-SENSE_CODE(0x2101, "Invalid element address")
-SENSE_CODE(0x2102, "Invalid address for write")
-SENSE_CODE(0x2103, "Invalid write crossing layer jump")
-SENSE_CODE(0x2104, "Unaligned write command")
-SENSE_CODE(0x2105, "Write boundary violation")
-SENSE_CODE(0x2106, "Attempt to read invalid data")
-SENSE_CODE(0x2107, "Read boundary violation")
-SENSE_CODE(0x2108, "Misaligned write command")
-SENSE_CODE(0x2109, "Attempt to access gap zone")
-
-SENSE_CODE(0x2200, "Illegal function (use 20 00, 24 00, or 26 00)")
-
-SENSE_CODE(0x2300, "Invalid token operation, cause not reportable")
-SENSE_CODE(0x2301, "Invalid token operation, unsupported token type")
-SENSE_CODE(0x2302, "Invalid token operation, remote token usage not supported")
-SENSE_CODE(0x2303, "Invalid token operation, remote rod token creation not supported")
-SENSE_CODE(0x2304, "Invalid token operation, token unknown")
-SENSE_CODE(0x2305, "Invalid token operation, token corrupt")
-SENSE_CODE(0x2306, "Invalid token operation, token revoked")
-SENSE_CODE(0x2307, "Invalid token operation, token expired")
-SENSE_CODE(0x2308, "Invalid token operation, token cancelled")
-SENSE_CODE(0x2309, "Invalid token operation, token deleted")
-SENSE_CODE(0x230A, "Invalid token operation, invalid token length")
-
-SENSE_CODE(0x2400, "Invalid field in cdb")
-SENSE_CODE(0x2401, "CDB decryption error")
-SENSE_CODE(0x2402, "Obsolete")
-SENSE_CODE(0x2403, "Obsolete")
-SENSE_CODE(0x2404, "Security audit value frozen")
-SENSE_CODE(0x2405, "Security working key frozen")
-SENSE_CODE(0x2406, "Nonce not unique")
-SENSE_CODE(0x2407, "Nonce timestamp out of range")
-SENSE_CODE(0x2408, "Invalid XCDB")
-SENSE_CODE(0x2409, "Invalid fast format")
-
-SENSE_CODE(0x2500, "Logical unit not supported")
-
-SENSE_CODE(0x2600, "Invalid field in parameter list")
-SENSE_CODE(0x2601, "Parameter not supported")
-SENSE_CODE(0x2602, "Parameter value invalid")
-SENSE_CODE(0x2603, "Threshold parameters not supported")
-SENSE_CODE(0x2604, "Invalid release of persistent reservation")
-SENSE_CODE(0x2605, "Data decryption error")
-SENSE_CODE(0x2606, "Too many target descriptors")
-SENSE_CODE(0x2607, "Unsupported target descriptor type code")
-SENSE_CODE(0x2608, "Too many segment descriptors")
-SENSE_CODE(0x2609, "Unsupported segment descriptor type code")
-SENSE_CODE(0x260A, "Unexpected inexact segment")
-SENSE_CODE(0x260B, "Inline data length exceeded")
-SENSE_CODE(0x260C, "Invalid operation for copy source or destination")
-SENSE_CODE(0x260D, "Copy segment granularity violation")
-SENSE_CODE(0x260E, "Invalid parameter while port is enabled")
-SENSE_CODE(0x260F, "Invalid data-out buffer integrity check value")
-SENSE_CODE(0x2610, "Data decryption key fail limit reached")
-SENSE_CODE(0x2611, "Incomplete key-associated data set")
-SENSE_CODE(0x2612, "Vendor specific key reference not found")
-SENSE_CODE(0x2613, "Application tag mode page is invalid")
-SENSE_CODE(0x2614, "Tape stream mirroring prevented")
-SENSE_CODE(0x2615, "Copy source or copy destination not authorized")
-SENSE_CODE(0x2616, "Fast copy not possible")
-
-SENSE_CODE(0x2700, "Write protected")
-SENSE_CODE(0x2701, "Hardware write protected")
-SENSE_CODE(0x2702, "Logical unit software write protected")
-SENSE_CODE(0x2703, "Associated write protect")
-SENSE_CODE(0x2704, "Persistent write protect")
-SENSE_CODE(0x2705, "Permanent write protect")
-SENSE_CODE(0x2706, "Conditional write protect")
-SENSE_CODE(0x2707, "Space allocation failed write protect")
-SENSE_CODE(0x2708, "Zone is read only")
-
-SENSE_CODE(0x2800, "Not ready to ready change, medium may have changed")
-SENSE_CODE(0x2801, "Import or export element accessed")
-SENSE_CODE(0x2802, "Format-layer may have changed")
-SENSE_CODE(0x2803, "Import/export element accessed, medium changed")
-
-SENSE_CODE(0x2900, "Power on, reset, or bus device reset occurred")
-SENSE_CODE(0x2901, "Power on occurred")
-SENSE_CODE(0x2902, "Scsi bus reset occurred")
-SENSE_CODE(0x2903, "Bus device reset function occurred")
-SENSE_CODE(0x2904, "Device internal reset")
-SENSE_CODE(0x2905, "Transceiver mode changed to single-ended")
-SENSE_CODE(0x2906, "Transceiver mode changed to lvd")
-SENSE_CODE(0x2907, "I_T nexus loss occurred")
-
-SENSE_CODE(0x2A00, "Parameters changed")
-SENSE_CODE(0x2A01, "Mode parameters changed")
-SENSE_CODE(0x2A02, "Log parameters changed")
-SENSE_CODE(0x2A03, "Reservations preempted")
-SENSE_CODE(0x2A04, "Reservations released")
-SENSE_CODE(0x2A05, "Registrations preempted")
-SENSE_CODE(0x2A06, "Asymmetric access state changed")
-SENSE_CODE(0x2A07, "Implicit asymmetric access state transition failed")
-SENSE_CODE(0x2A08, "Priority changed")
-SENSE_CODE(0x2A09, "Capacity data has changed")
-SENSE_CODE(0x2A0A, "Error history I_T nexus cleared")
-SENSE_CODE(0x2A0B, "Error history snapshot released")
-SENSE_CODE(0x2A0C, "Error recovery attributes have changed")
-SENSE_CODE(0x2A0D, "Data encryption capabilities changed")
-SENSE_CODE(0x2A10, "Timestamp changed")
-SENSE_CODE(0x2A11, "Data encryption parameters changed by another i_t nexus")
-SENSE_CODE(0x2A12, "Data encryption parameters changed by vendor specific event")
-SENSE_CODE(0x2A13, "Data encryption key instance counter has changed")
-SENSE_CODE(0x2A14, "SA creation capabilities data has changed")
-SENSE_CODE(0x2A15, "Medium removal prevention preempted")
-SENSE_CODE(0x2A16, "Zone reset write pointer recommended")
-
-SENSE_CODE(0x2B00, "Copy cannot execute since host cannot disconnect")
-
-SENSE_CODE(0x2C00, "Command sequence error")
-SENSE_CODE(0x2C01, "Too many windows specified")
-SENSE_CODE(0x2C02, "Invalid combination of windows specified")
-SENSE_CODE(0x2C03, "Current program area is not empty")
-SENSE_CODE(0x2C04, "Current program area is empty")
-SENSE_CODE(0x2C05, "Illegal power condition request")
-SENSE_CODE(0x2C06, "Persistent prevent conflict")
-SENSE_CODE(0x2C07, "Previous busy status")
-SENSE_CODE(0x2C08, "Previous task set full status")
-SENSE_CODE(0x2C09, "Previous reservation conflict status")
-SENSE_CODE(0x2C0A, "Partition or collection contains user objects")
-SENSE_CODE(0x2C0B, "Not reserved")
-SENSE_CODE(0x2C0C, "Orwrite generation does not match")
-SENSE_CODE(0x2C0D, "Reset write pointer not allowed")
-SENSE_CODE(0x2C0E, "Zone is offline")
-SENSE_CODE(0x2C0F, "Stream not open")
-SENSE_CODE(0x2C10, "Unwritten data in zone")
-SENSE_CODE(0x2C11, "Descriptor format sense data required")
-SENSE_CODE(0x2C12, "Zone is inactive")
-SENSE_CODE(0x2C13, "Well known logical unit access required")
-
-SENSE_CODE(0x2D00, "Overwrite error on update in place")
-
-SENSE_CODE(0x2E00, "Insufficient time for operation")
-SENSE_CODE(0x2E01, "Command timeout before processing")
-SENSE_CODE(0x2E02, "Command timeout during processing")
-SENSE_CODE(0x2E03, "Command timeout during processing due to error recovery")
-
-SENSE_CODE(0x2F00, "Commands cleared by another initiator")
-SENSE_CODE(0x2F01, "Commands cleared by power loss notification")
-SENSE_CODE(0x2F02, "Commands cleared by device server")
-SENSE_CODE(0x2F03, "Some commands cleared by queuing layer event")
-
-SENSE_CODE(0x3000, "Incompatible medium installed")
-SENSE_CODE(0x3001, "Cannot read medium - unknown format")
-SENSE_CODE(0x3002, "Cannot read medium - incompatible format")
-SENSE_CODE(0x3003, "Cleaning cartridge installed")
-SENSE_CODE(0x3004, "Cannot write medium - unknown format")
-SENSE_CODE(0x3005, "Cannot write medium - incompatible format")
-SENSE_CODE(0x3006, "Cannot format medium - incompatible medium")
-SENSE_CODE(0x3007, "Cleaning failure")
-SENSE_CODE(0x3008, "Cannot write - application code mismatch")
-SENSE_CODE(0x3009, "Current session not fixated for append")
-SENSE_CODE(0x300A, "Cleaning request rejected")
-SENSE_CODE(0x300C, "WORM medium - overwrite attempted")
-SENSE_CODE(0x300D, "WORM medium - integrity check")
-SENSE_CODE(0x3010, "Medium not formatted")
-SENSE_CODE(0x3011, "Incompatible volume type")
-SENSE_CODE(0x3012, "Incompatible volume qualifier")
-SENSE_CODE(0x3013, "Cleaning volume expired")
-
-SENSE_CODE(0x3100, "Medium format corrupted")
-SENSE_CODE(0x3101, "Format command failed")
-SENSE_CODE(0x3102, "Zoned formatting failed due to spare linking")
-SENSE_CODE(0x3103, "Sanitize command failed")
-SENSE_CODE(0x3104, "Depopulation failed")
-SENSE_CODE(0x3105, "Depopulation restoration failed")
-
-SENSE_CODE(0x3200, "No defect spare location available")
-SENSE_CODE(0x3201, "Defect list update failure")
-
-SENSE_CODE(0x3300, "Tape length error")
-
-SENSE_CODE(0x3400, "Enclosure failure")
-
-SENSE_CODE(0x3500, "Enclosure services failure")
-SENSE_CODE(0x3501, "Unsupported enclosure function")
-SENSE_CODE(0x3502, "Enclosure services unavailable")
-SENSE_CODE(0x3503, "Enclosure services transfer failure")
-SENSE_CODE(0x3504, "Enclosure services transfer refused")
-SENSE_CODE(0x3505, "Enclosure services checksum error")
-
-SENSE_CODE(0x3600, "Ribbon, ink, or toner failure")
-
-SENSE_CODE(0x3700, "Rounded parameter")
-
-SENSE_CODE(0x3800, "Event status notification")
-SENSE_CODE(0x3802, "Esn - power management class event")
-SENSE_CODE(0x3804, "Esn - media class event")
-SENSE_CODE(0x3806, "Esn - device busy class event")
-SENSE_CODE(0x3807, "Thin Provisioning soft threshold reached")
-SENSE_CODE(0x3808, "Depopulation interrupted")
-
-SENSE_CODE(0x3900, "Saving parameters not supported")
-
-SENSE_CODE(0x3A00, "Medium not present")
-SENSE_CODE(0x3A01, "Medium not present - tray closed")
-SENSE_CODE(0x3A02, "Medium not present - tray open")
-SENSE_CODE(0x3A03, "Medium not present - loadable")
-SENSE_CODE(0x3A04, "Medium not present - medium auxiliary memory accessible")
-
-SENSE_CODE(0x3B00, "Sequential positioning error")
-SENSE_CODE(0x3B01, "Tape position error at beginning-of-medium")
-SENSE_CODE(0x3B02, "Tape position error at end-of-medium")
-SENSE_CODE(0x3B03, "Tape or electronic vertical forms unit not ready")
-SENSE_CODE(0x3B04, "Slew failure")
-SENSE_CODE(0x3B05, "Paper jam")
-SENSE_CODE(0x3B06, "Failed to sense top-of-form")
-SENSE_CODE(0x3B07, "Failed to sense bottom-of-form")
-SENSE_CODE(0x3B08, "Reposition error")
-SENSE_CODE(0x3B09, "Read past end of medium")
-SENSE_CODE(0x3B0A, "Read past beginning of medium")
-SENSE_CODE(0x3B0B, "Position past end of medium")
-SENSE_CODE(0x3B0C, "Position past beginning of medium")
-SENSE_CODE(0x3B0D, "Medium destination element full")
-SENSE_CODE(0x3B0E, "Medium source element empty")
-SENSE_CODE(0x3B0F, "End of medium reached")
-SENSE_CODE(0x3B11, "Medium magazine not accessible")
-SENSE_CODE(0x3B12, "Medium magazine removed")
-SENSE_CODE(0x3B13, "Medium magazine inserted")
-SENSE_CODE(0x3B14, "Medium magazine locked")
-SENSE_CODE(0x3B15, "Medium magazine unlocked")
-SENSE_CODE(0x3B16, "Mechanical positioning or changer error")
-SENSE_CODE(0x3B17, "Read past end of user object")
-SENSE_CODE(0x3B18, "Element disabled")
-SENSE_CODE(0x3B19, "Element enabled")
-SENSE_CODE(0x3B1A, "Data transfer device removed")
-SENSE_CODE(0x3B1B, "Data transfer device inserted")
-SENSE_CODE(0x3B1C, "Too many logical objects on partition to support operation")
-SENSE_CODE(0x3B20, "Element static information changed")
-
-SENSE_CODE(0x3D00, "Invalid bits in identify message")
-
-SENSE_CODE(0x3E00, "Logical unit has not self-configured yet")
-SENSE_CODE(0x3E01, "Logical unit failure")
-SENSE_CODE(0x3E02, "Timeout on logical unit")
-SENSE_CODE(0x3E03, "Logical unit failed self-test")
-SENSE_CODE(0x3E04, "Logical unit unable to update self-test log")
-
-SENSE_CODE(0x3F00, "Target operating conditions have changed")
-SENSE_CODE(0x3F01, "Microcode has been changed")
-SENSE_CODE(0x3F02, "Changed operating definition")
-SENSE_CODE(0x3F03, "Inquiry data has changed")
-SENSE_CODE(0x3F04, "Component device attached")
-SENSE_CODE(0x3F05, "Device identifier changed")
-SENSE_CODE(0x3F06, "Redundancy group created or modified")
-SENSE_CODE(0x3F07, "Redundancy group deleted")
-SENSE_CODE(0x3F08, "Spare created or modified")
-SENSE_CODE(0x3F09, "Spare deleted")
-SENSE_CODE(0x3F0A, "Volume set created or modified")
-SENSE_CODE(0x3F0B, "Volume set deleted")
-SENSE_CODE(0x3F0C, "Volume set deassigned")
-SENSE_CODE(0x3F0D, "Volume set reassigned")
-SENSE_CODE(0x3F0E, "Reported luns data has changed")
-SENSE_CODE(0x3F0F, "Echo buffer overwritten")
-SENSE_CODE(0x3F10, "Medium loadable")
-SENSE_CODE(0x3F11, "Medium auxiliary memory accessible")
-SENSE_CODE(0x3F12, "iSCSI IP address added")
-SENSE_CODE(0x3F13, "iSCSI IP address removed")
-SENSE_CODE(0x3F14, "iSCSI IP address changed")
-SENSE_CODE(0x3F15, "Inspect referrals sense descriptors")
-SENSE_CODE(0x3F16, "Microcode has been changed without reset")
-SENSE_CODE(0x3F17, "Zone transition to full")
-SENSE_CODE(0x3F18, "Bind completed")
-SENSE_CODE(0x3F19, "Bind redirected")
-SENSE_CODE(0x3F1A, "Subsidiary binding changed")
+SENSE_CODE(NO_ADDITIONAL_SENSE_INFORMATION,
+	   "No additional sense information")
+SENSE_CODE(FILEMARK_DETECTED,
+	   "Filemark detected")
+SENSE_CODE(END_OF_PARTITION_MEDIUM_DETECTED,
+	   "End-of-partition/medium detected")
+SENSE_CODE(SETMARK_DETECTED,
+	   "Setmark detected")
+SENSE_CODE(BEGINNING_OF_PARTITION_MEDIUM_DETECTED,
+	   "Beginning-of-partition/medium detected")
+SENSE_CODE(END_OF_DATA_DETECTED,
+	   "End-of-data detected")
+SENSE_CODE(IO_PROCESS_TERMINATED,
+	   "I/O process terminated")
+SENSE_CODE(PROGRAMMABLE_EARLY_WARNING_DETECTED,
+	   "Programmable early warning detected")
+SENSE_CODE(AUDIO_PLAY_OP_IN_PROGRESS,
+	   "Audio play operation in progress")
+SENSE_CODE(AUDIO_PLAY_OP_PAUSED,
+	   "Audio play operation paused")
+SENSE_CODE(AUDIO_PLAY_OP_SUCCESSFULLY_COMPLETED,
+	   "Audio play operation successfully completed")
+SENSE_CODE(AUDIO_PLAY_OP_STOPPED_DUE_TO_ERROR,
+	   "Audio play operation stopped due to error")
+SENSE_CODE(NO_CURRENT_AUDIO_STATUS_TO_RETURN,
+	   "No current audio status to return")
+SENSE_CODE(OP_IN_PROGRESS,
+	   "Operation in progress")
+SENSE_CODE(CLEANING_REQUESTED,
+	   "Cleaning requested")
+SENSE_CODE(ERASE_OP_IN_PROGRESS,
+	   "Erase operation in progress")
+SENSE_CODE(LOCATE_OP_IN_PROGRESS,
+	   "Locate operation in progress")
+SENSE_CODE(REWIND_OP_IN_PROGRESS,
+	   "Rewind operation in progress")
+SENSE_CODE(SET_CAPACITY_OP_IN_PROGRESS,
+	   "Set capacity operation in progress")
+SENSE_CODE(VERIFY_OP_IN_PROGRESS,
+	   "Verify operation in progress")
+SENSE_CODE(ATA_PASS_THROUGH_INFORMATION_AVAILABLE,
+	   "ATA pass through information available")
+SENSE_CODE(CONFLICTING_SA_CREATION_REQUEST,
+	   "Conflicting SA creation request")
+SENSE_CODE(LU_TRANSITIONING_TO_ANOTHER_POWER_CONDITION,
+	   "Logical unit transitioning to another power condition")
+SENSE_CODE(EXTENDED_COPY_INFORMATION_AVAILABLE,
+	   "Extended copy information available")
+SENSE_CODE(ATOMIC_COMMAND_ABORTED_DUE_TO_ACA,
+	   "Atomic command aborted due to ACA")
+SENSE_CODE(DEFERRED_MICROCODE_IS_PENDING,
+	   "Deferred microcode is pending")
+SENSE_CODE(OVERLAPPING_ATOMIC_COMMAND_IN_PROGRESS,
+	   "Overlapping atomic command in progress")
+
+SENSE_CODE(NO_INDEX_SECTOR_SIGNAL,
+	   "No index/sector signal")
+
+SENSE_CODE(NO_SEEK_COMPLETE,
+	   "No seek complete")
+
+SENSE_CODE(PERIPHERAL_DEVICE_WRITE_FAULT,
+	   "Peripheral device write fault")
+SENSE_CODE(NO_WRITE_CURRENT,
+	   "No write current")
+SENSE_CODE(EXCESSIVE_WRITE_ERRORS,
+	   "Excessive write errors")
+
+SENSE_CODE(LU_NOT_READY,
+	   "Logical unit not ready, cause not reportable")
+SENSE_CODE(LU_IS_IN_PROCESS_OF_BECOMING_READY,
+	   "Logical unit is in process of becoming ready")
+SENSE_CODE(LU_NOT_READY_INITIALIZING_COMMAND_REQUIRED,
+	   "Logical unit not ready, initializing command required")
+SENSE_CODE(LU_NOT_READY_MANUAL_INTERVENTION_REQUIRED,
+	   "Logical unit not ready, manual intervention required")
+SENSE_CODE(LU_NOT_READY_FORMAT_IN_PROGRESS,
+	   "Logical unit not ready, format in progress")
+SENSE_CODE(LU_NOT_READY_REBUILD_IN_PROGRESS,
+	   "Logical unit not ready, rebuild in progress")
+SENSE_CODE(LU_NOT_READY_RECALCULATION_IN_PROGRESS,
+	   "Logical unit not ready, recalculation in progress")
+SENSE_CODE(LU_NOT_READY_OP_IN_PROGRESS,
+	   "Logical unit not ready, operation in progress")
+SENSE_CODE(LU_NOT_READY_LONG_WRITE_IN_PROGRESS,
+	   "Logical unit not ready, long write in progress")
+SENSE_CODE(LU_NOT_READY_SELFTEST_IN_PROGRESS,
+	   "Logical unit not ready, self-test in progress")
+SENSE_CODE(LU_NOT_ACCESSIBLE_ASYMMETRIC_ACCESS_STATE_TRANSITION,
+	   "Logical unit not accessible, asymmetric access state transition")
+SENSE_CODE(LU_NOT_ACCESSIBLE_TARGET_PORT_IN_STANDBY_STATE,
+	   "Logical unit not accessible, target port in standby state")
+SENSE_CODE(LU_NOT_ACCESSIBLE_TARGET_PORT_IN_UNAVAILABLE_STATE,
+	   "Logical unit not accessible, target port in unavailable state")
+SENSE_CODE(LU_NOT_READY_STRUCTURE_CHECK_REQUIRED,
+	   "Logical unit not ready, structure check required")
+SENSE_CODE(LU_NOT_READY_SECURITY_SESSION_IN_PROGRESS,
+	   "Logical unit not ready, security session in progress")
+SENSE_CODE(LU_NOT_READY_AUXILIARY_MEMORY_NOT_ACCESSIBLE,
+	   "Logical unit not ready, auxiliary memory not accessible")
+SENSE_CODE(LU_NOT_READY_NOTIFY_REQUIRED,
+	   "Logical unit not ready, notify (enable spinup) required")
+SENSE_CODE(LU_NOT_READY_OFFLINE,
+	   "Logical unit not ready, offline")
+SENSE_CODE(LU_NOT_READY_SA_CREATION_IN_PROGRESS,
+	   "Logical unit not ready, SA creation in progress")
+SENSE_CODE(LU_NOT_READY_SPACE_ALLOCATION_IN_PROGRESS,
+	   "Logical unit not ready, space allocation in progress")
+SENSE_CODE(LU_NOT_READY_ROBOTICS_DISABLED,
+	   "Logical unit not ready, robotics disabled")
+SENSE_CODE(LU_NOT_READY_CONFIG_REQUIRED,
+	   "Logical unit not ready, configuration required")
+SENSE_CODE(LU_NOT_READY_CALIBRATION_REQUIRED,
+	   "Logical unit not ready, calibration required")
+SENSE_CODE(LU_NOT_READY_A_DOOR_IS_OPEN,
+	   "Logical unit not ready, a door is open")
+SENSE_CODE(LU_NOT_READY_OPERATING_IN_SEQUENTIAL_MODE,
+	   "Logical unit not ready, operating in sequential mode")
+SENSE_CODE(LU_NOT_READY_START_STOP_UNIT_COMMAND_IN_PROGRESS,
+	   "Logical unit not ready, start stop unit command in progress")
+SENSE_CODE(LU_NOT_READY_SANITIZE_IN_PROGRESS,
+	   "Logical unit not ready, sanitize in progress")
+SENSE_CODE(LU_NOT_READY_ADDITIONAL_POWER_USE_NOT_YET_GRANTED,
+	   "Logical unit not ready, additional power use not yet granted")
+SENSE_CODE(LU_NOT_READY_CONFIG_IN_PROGRESS,
+	   "Logical unit not ready, configuration in progress")
+SENSE_CODE(LU_NOT_READY_MICROCODE_ACTIVATION_REQUIRED,
+	   "Logical unit not ready, microcode activation required")
+SENSE_CODE(LU_NOT_READY_MICROCODE_DOWNLOAD_REQUIRED,
+	   "Logical unit not ready, microcode download required")
+SENSE_CODE(LU_NOT_READY_LU_RESET_REQUIRED,
+	   "Logical unit not ready, logical unit reset required")
+SENSE_CODE(LU_NOT_READY_HARD_RESET_REQUIRED,
+	   "Logical unit not ready, hard reset required")
+SENSE_CODE(LU_NOT_READY_POWER_CYCLE_REQUIRED,
+	   "Logical unit not ready, power cycle required")
+SENSE_CODE(LU_NOT_READY_AFFILIATION_REQUIRED,
+	   "Logical unit not ready, affiliation required")
+SENSE_CODE(DEPOPULATION_IN_PROGRESS,
+	   "Depopulation in progress")
+SENSE_CODE(DEPOPULATION_RESTORATION_IN_PROGRESS,
+	   "Depopulation restoration in progress")
+
+SENSE_CODE(LU_DOES_NOT_RESPOND_TO_SELECTION,
+	   "Logical unit does not respond to selection")
+
+SENSE_CODE(NO_REFERENCE_POSITION_FOUND,
+	   "No reference position found")
+
+SENSE_CODE(MULTIPLE_PERIPHERAL_DEVICES_SELECTED,
+	   "Multiple peripheral devices selected")
+
+SENSE_CODE(LU_COMMUNICATION_FAILURE,
+	   "Logical unit communication failure")
+SENSE_CODE(LU_COMMUNICATION_TIMEOUT,
+	   "Logical unit communication time-out")
+SENSE_CODE(LU_COMMUNICATION_PARITY_ERROR,
+	   "Logical unit communication parity error")
+SENSE_CODE(LU_COMMUNICATION_CRC_ERROR,
+	   "Logical unit communication CRC error (Ultra-DMA/32)")
+SENSE_CODE(UNREACHABLE_COPY_TARGET,
+	   "Unreachable copy target")
+
+SENSE_CODE(TRACK_FOLLOWING_ERROR,
+	   "Track following error")
+SENSE_CODE(TRACKING_SERVO_FAILURE,
+	   "Tracking servo failure")
+SENSE_CODE(FOCUS_SERVO_FAILURE,
+	   "Focus servo failure")
+SENSE_CODE(SPINDLE_SERVO_FAILURE,
+	   "Spindle servo failure")
+SENSE_CODE(HEAD_SELECT_FAULT,
+	   "Head select fault")
+SENSE_CODE(VIBRATION_INDUCED_TRACKING_ERROR,
+	   "Vibration induced tracking error")
+
+SENSE_CODE(ERROR_LOG_OVERFLOW,
+	   "Error log overflow")
+
+SENSE_CODE(SSC_WARNING,
+	   "Warning")
+SENSE_CODE(WARNING_SPECIFIED_TEMPERATURE_EXCEEDED,
+	   "Warning - specified temperature exceeded")
+SENSE_CODE(WARNING_ENCLOSURE_DEGRADED,
+	   "Warning - enclosure degraded")
+SENSE_CODE(WARNING_BACKGROUND_SELFTEST_FAILED,
+	   "Warning - background self-test failed")
+SENSE_CODE(WARNING_BACKGROUND_PRESCAN_DETECTED_MEDIUM_ERROR,
+	   "Warning - background pre-scan detected medium error")
+SENSE_CODE(WARNING_BACKGROUND_MEDIUM_SCAN_DETECTED_MEDIUM_ERROR,
+	   "Warning - background medium scan detected medium error")
+SENSE_CODE(WARNING_NONVOLATILE_CACHE_NOW_VOLATILE,
+	   "Warning - non-volatile cache now volatile")
+SENSE_CODE(WARNING_DEGRADED_POWER_TO_NONVOLATILE_CACHE,
+	   "Warning - degraded power to non-volatile cache")
+SENSE_CODE(WARNING_POWER_LOSS_EXPECTED,
+	   "Warning - power loss expected")
+SENSE_CODE(WARNING_DEVICE_STATISTICS_NOTIFICATION_ACTIVE,
+	   "Warning - device statistics notification active")
+SENSE_CODE(WARNING_HIGH_CRITICAL_TEMPERATURE_LIMIT_EXCEEDED,
+	   "Warning - high critical temperature limit exceeded")
+SENSE_CODE(WARNING_LOW_CRITICAL_TEMPERATURE_LIMIT_EXCEEDED,
+	   "Warning - low critical temperature limit exceeded")
+SENSE_CODE(WARNING_HIGH_OPERATING_TEMPERATURE_LIMIT_EXCEEDED,
+	   "Warning - high operating temperature limit exceeded")
+SENSE_CODE(WARNING_LOW_OPERATING_TEMPERATURE_LIMIT_EXCEEDED,
+	   "Warning - low operating temperature limit exceeded")
+SENSE_CODE(WARNING_HIGH_CRITICAL_HUMIDITY_LIMIT_EXCEEDED,
+	   "Warning - high critical humidity limit exceeded")
+SENSE_CODE(WARNING_LOW_CRITICAL_HUMIDITY_LIMIT_EXCEEDED,
+	   "Warning - low critical humidity limit exceeded")
+SENSE_CODE(WARNING_HIGH_OPERATING_HUMIDITY_LIMIT_EXCEEDED,
+	   "Warning - high operating humidity limit exceeded")
+SENSE_CODE(WARNING_LOW_OPERATING_HUMIDITY_LIMIT_EXCEEDED,
+	   "Warning - low operating humidity limit exceeded")
+SENSE_CODE(WARNING_MICROCODE_SECURITY_AT_RISK,
+	   "Warning - microcode security at risk")
+SENSE_CODE(WARNING_MICROCODE_DIGITAL_SIGNATURE_VALIDATION_FAILURE,
+	   "Warning - microcode digital signature validation failure")
+SENSE_CODE(WARNING_PHYSICAL_ELEMENT_STATUS_CHANGE,
+	   "Warning - physical element status change")
+
+SENSE_CODE(SSC_WRITE_ERROR,
+	   "Write error")
+SENSE_CODE(WRITE_ERROR_RECOVERED_WITH_AUTO_REALLOCATION,
+	   "Write error - recovered with auto reallocation")
+SENSE_CODE(WRITE_ERROR_AUTO_REALLOCATION_FAILED,
+	   "Write error - auto reallocation failed")
+SENSE_CODE(WRITE_ERROR_RECOMMEND_REASSIGNMENT,
+	   "Write error - recommend reassignment")
+SENSE_CODE(COMPRESSION_CHECK_MISCOMPARE_ERROR,
+	   "Compression check miscompare error")
+SENSE_CODE(DATA_EXPANSION_OCCURRED_DURING_COMPRESSION,
+	   "Data expansion occurred during compression")
+SENSE_CODE(BLOCK_NOT_COMPRESSIBLE,
+	   "Block not compressible")
+SENSE_CODE(WRITE_ERROR_RECOVERY_NEEDED,
+	   "Write error - recovery needed")
+SENSE_CODE(WRITE_ERROR_RECOVERY_FAILED,
+	   "Write error - recovery failed")
+SENSE_CODE(WRITE_ERROR_LOSS_OF_STREAMING,
+	   "Write error - loss of streaming")
+SENSE_CODE(WRITE_ERROR_PADDING_BLOCKS_ADDED,
+	   "Write error - padding blocks added")
+SENSE_CODE(AUXILIARY_MEMORY_WRITE_ERROR,
+	   "Auxiliary memory write error")
+SENSE_CODE(WRITE_ERROR_UNEXPECTED_UNSOLICITED_DATA,
+	   "Write error - unexpected unsolicited data")
+SENSE_CODE(WRITE_ERROR_NOT_ENOUGH_UNSOLICITED_DATA,
+	   "Write error - not enough unsolicited data")
+SENSE_CODE(MULTIPLE_WRITE_ERRORS,
+	   "Multiple write errors")
+SENSE_CODE(DEFECTS_IN_ERROR_WINDOW,
+	   "Defects in error window")
+SENSE_CODE(INCOMPLETE_MULTIPLE_ATOMIC_WRITE_OPERATIONS,
+	   "Incomplete multiple atomic write operations")
+SENSE_CODE(WRITE_ERROR_RECOVERY_SCAN_NEEDED,
+	   "Write error - recovery scan needed")
+SENSE_CODE(WRITE_ERROR_INSUFFICIENT_ZONE_RESOURCES,
+	   "Write error - insufficient zone resources")
+
+SENSE_CODE(ERROR_DETECTED_BY_THIRD_PARTY_TEMPORARY_INITIATOR,
+	   "Error detected by third party temporary initiator")
+SENSE_CODE(THIRD_PARTY_DEVICE_FAILURE,
+	   "Third party device failure")
+SENSE_CODE(COPY_TARGET_DEVICE_NOT_REACHABLE,
+	   "Copy target device not reachable")
+SENSE_CODE(INCORRECT_COPY_TARGET_DEVICE_TYPE,
+	   "Incorrect copy target device type")
+SENSE_CODE(COPY_TARGET_DEVICE_DATA_UNDERRUN,
+	   "Copy target device data underrun")
+SENSE_CODE(COPY_TARGET_DEVICE_DATA_OVERRUN,
+	   "Copy target device data overrun")
+
+SENSE_CODE(INVALID_INFORMATION_UNIT,
+	   "Invalid information unit")
+SENSE_CODE(INFORMATION_UNIT_TOO_SHORT,
+	   "Information unit too short")
+SENSE_CODE(INFORMATION_UNIT_TOO_LONG,
+	   "Information unit too long")
+SENSE_CODE(INVALID_FIELD_IN_COMMAND_INFORMATION_UNIT,
+	   "Invalid field in command information unit")
+
+SENSE_CODE(ID_CRC_OR_ECC_ERROR,
+	   "Id CRC or ECC error")
+SENSE_CODE(LOGICAL_BLOCK_GUARD_CHECK_FAILED,
+	   "Logical block guard check failed")
+SENSE_CODE(LOGICAL_BLOCK_APPLICATION_TAG_CHECK_FAILED,
+	   "Logical block application tag check failed")
+SENSE_CODE(LOGICAL_BLOCK_REFERENCE_TAG_CHECK_FAILED,
+	   "Logical block reference tag check failed")
+SENSE_CODE(LOGICAL_BLOCK_PROTECTION_ERROR_ON_RECOVER_BUFFERED_DATA,
+	   "Logical block protection error on recover buffered data")
+SENSE_CODE(LOGICAL_BLOCK_PROTECTION_METHOD_ERROR,
+	   "Logical block protection method error")
+
+SENSE_CODE(UNRECOVERED_READ_ERROR,
+	   "Unrecovered read error")
+SENSE_CODE(READ_RETRIES_EXHAUSTED,
+	   "Read retries exhausted")
+SENSE_CODE(ERROR_TOO_LONG_TO_CORRECT,
+	   "Error too long to correct")
+SENSE_CODE(MULTIPLE_READ_ERRORS,
+	   "Multiple read errors")
+SENSE_CODE(UNRECOVERED_READ_ERROR_AUTO_REALLOCATE_FAILED,
+	   "Unrecovered read error - auto reallocate failed")
+SENSE_CODE(LEC_UNCORRECTABLE_ERROR,
+	   "L-EC uncorrectable error")
+SENSE_CODE(CIRC_UNRECOVERED_ERROR,
+	   "CIRC unrecovered error")
+SENSE_CODE(DATA_RESYNCHRONIZATION_ERROR,
+	   "Data re-synchronization error")
+SENSE_CODE(INCOMPLETE_BLOCK_READ,
+	   "Incomplete block read")
+SENSE_CODE(NO_GAP_FOUND,
+	   "No gap found")
+SENSE_CODE(MISCORRECTED_ERROR,
+	   "Miscorrected error")
+SENSE_CODE(UNRECOVERED_READ_ERROR_RECOMMEND_REASSIGNMENT,
+	   "Unrecovered read error - recommend reassignment")
+SENSE_CODE(UNRECOVERED_READ_ERROR_RECOMMEND_REWRITE_THE_DATA,
+	   "Unrecovered read error - recommend rewrite the data")
+SENSE_CODE(DECOMPRESSION_CRC_ERROR,
+	   "De-compression CRC error")
+SENSE_CODE(CANNOT_DECOMPRESS_USING_DECLARED_ALGORITHM,
+	   "Cannot decompress using declared algorithm")
+SENSE_CODE(ERROR_READING_UPC_EAN_NUMBER,
+	   "Error reading UPC/EAN number")
+SENSE_CODE(ERROR_READING_ISRC_NUMBER,
+	   "Error reading ISRC number")
+SENSE_CODE(READ_ERROR_LOSS_OF_STREAMING,
+	   "Read error - loss of streaming")
+SENSE_CODE(AUXILIARY_MEMORY_READ_ERROR,
+	   "Auxiliary memory read error")
+SENSE_CODE(READ_ERROR_FAILED_RETRANSMISSION_REQUEST,
+	   "Read error - failed retransmission request")
+SENSE_CODE(READ_ERROR_LBA_MARKED_BAD_BY_APPLICATION_CLIENT,
+	   "Read error - lba marked bad by application client")
+SENSE_CODE(WRITE_AFTER_SANITIZE_REQUIRED,
+	   "Write after sanitize required")
+
+SENSE_CODE(ADDRESS_MARK_NOT_FOUND_FOR_ID_FIELD,
+	   "Address mark not found for id field")
+
+SENSE_CODE(ADDRESS_MARK_NOT_FOUND_FOR_DATA_FIELD,
+	   "Address mark not found for data field")
+
+SENSE_CODE(RECORDED_ENTITY_NOT_FOUND,
+	   "Recorded entity not found")
+SENSE_CODE(RECORD_NOT_FOUND,
+	   "Record not found")
+SENSE_CODE(FILEMARK_OR_SETMARK_NOT_FOUND,
+	   "Filemark or setmark not found")
+SENSE_CODE(END_OF_DATA_NOT_FOUND,
+	   "End-of-data not found")
+SENSE_CODE(BLOCK_SEQUENCE_ERROR,
+	   "Block sequence error")
+SENSE_CODE(RECORD_NOT_FOUND_RECOMMEND_REASSIGNMENT,
+	   "Record not found - recommend reassignment")
+SENSE_CODE(RECORD_NOT_FOUND_DATA_AUTO_REALLOCATED,
+	   "Record not found - data auto-reallocated")
+SENSE_CODE(LOCATE_OPERATION_FAILURE,
+	   "Locate operation failure")
+
+SENSE_CODE(RANDOM_POSITIONING_ERROR,
+	   "Random positioning error")
+SENSE_CODE(MECHANICAL_POSITIONING_ERROR,
+	   "Mechanical positioning error")
+SENSE_CODE(POSITIONING_ERROR_DETECTED_BY_READ_OF_MEDIUM,
+	   "Positioning error detected by read of medium")
+
+SENSE_CODE(DATA_SYNCHRONIZATION_MARK_ERROR,
+	   "Data synchronization mark error")
+SENSE_CODE(DATA_SYNC_ERROR_DATA_REWRITTEN,
+	   "Data sync error - data rewritten")
+SENSE_CODE(DATA_SYNC_ERROR_RECOMMEND_REWRITE,
+	   "Data sync error - recommend rewrite")
+SENSE_CODE(DATA_SYNC_ERROR_DATA_AUTO_REALLOCATED,
+	   "Data sync error - data auto-reallocated")
+SENSE_CODE(DATA_SYNC_ERROR_RECOMMEND_REASSIGNMENT,
+	   "Data sync error - recommend reassignment")
+
+SENSE_CODE(RECOVERED_DATA_WITH_NO_ERROR_CORRECTION_APPLIED,
+	   "Recovered data with no error correction applied")
+SENSE_CODE(RECOVERED_DATA_WITH_RETRIES,
+	   "Recovered data with retries")
+SENSE_CODE(RECOVERED_DATA_WITH_POSITIVE_HEAD_OFFSET,
+	   "Recovered data with positive head offset")
+SENSE_CODE(RECOVERED_DATA_WITH_NEGATIVE_HEAD_OFFSET,
+	   "Recovered data with negative head offset")
+SENSE_CODE(RECOVERED_DATA_WITH_RETRIES_AND_OR_CIRC_APPLIED,
+	   "Recovered data with retries and/or circ applied")
+SENSE_CODE(RECOVERED_DATA_USING_PREVIOUS_SECTOR_ID,
+	   "Recovered data using previous sector id")
+SENSE_CODE(RECOVERED_DATA_WITHOUT_ECC_DATA_AUTO_REALLOCATED,
+	   "Recovered data without ECC - data auto-reallocated")
+SENSE_CODE(RECOVERED_DATA_WITHOUT_ECC_RECOMMEND_REASSIGNMENT,
+	   "Recovered data without ECC - recommend reassignment")
+SENSE_CODE(RECOVERED_DATA_WITHOUT_ECC_RECOMMEND_REWRITE,
+	   "Recovered data without ECC - recommend rewrite")
+SENSE_CODE(RECOVERED_DATA_WITHOUT_ECC_DATA_REWRITTEN,
+	   "Recovered data without ECC - data rewritten")
+
+SENSE_CODE(RECOVERED_DATA_WITH_ERROR_CORRECTION_APPLIED,
+	   "Recovered data with error correction applied")
+SENSE_CODE(RECOVERED_DATA_WITH_ERROR_CORRECTION_RETRIES_APPLIED,
+	   "Recovered data with error corr. & retries applied")
+SENSE_CODE(RECOVERED_DATA_DATA_AUTO_REALLOCATED,
+	   "Recovered data - data auto-reallocated")
+SENSE_CODE(RECOVERED_DATA_WITH_CIRC,
+	   "Recovered data with CIRC")
+SENSE_CODE(RECOVERED_DATA_WITH_LEC,
+	   "Recovered data with L-EC")
+SENSE_CODE(RECOVERED_DATA_RECOMMEND_REASSIGNMENT,
+	   "Recovered data - recommend reassignment")
+SENSE_CODE(RECOVERED_DATA_RECOMMEND_REWRITE,
+	   "Recovered data - recommend rewrite")
+SENSE_CODE(RECOVERED_DATA_WITH_ECC_DATA_REWRITTEN,
+	   "Recovered data with ECC - data rewritten")
+SENSE_CODE(RECOVERED_DATA_WITH_LINKING,
+	   "Recovered data with linking")
+
+SENSE_CODE(DEFECT_LIST_ERROR,
+	   "Defect list error")
+SENSE_CODE(DEFECT_LIST_NOT_AVAILABLE,
+	   "Defect list not available")
+SENSE_CODE(DEFECT_LIST_ERROR_IN_PRIMARY_LIST,
+	   "Defect list error in primary list")
+SENSE_CODE(DEFECT_LIST_ERROR_IN_GROWN_LIST,
+	   "Defect list error in grown list")
+
+SENSE_CODE(PARAMETER_LIST_LENGTH_ERROR,
+	   "Parameter list length error")
+
+SENSE_CODE(SYNCHRONOUS_DATA_TRANSFER_ERROR,
+	   "Synchronous data transfer error")
+
+SENSE_CODE(DEFECT_LIST_NOT_FOUND,
+	   "Defect list not found")
+SENSE_CODE(PRIMARY_DEFECT_LIST_NOT_FOUND,
+	   "Primary defect list not found")
+SENSE_CODE(GROWN_DEFECT_LIST_NOT_FOUND,
+	   "Grown defect list not found")
+
+SENSE_CODE(MISCOMPARE_DURING_VERIFY_OPERATION,
+	   "Miscompare during verify operation")
+SENSE_CODE(MISCOMPARE_VERIFY_OF_UNMAPPED_LBA,
+	   "Miscompare verify of unmapped LBA")
+
+SENSE_CODE(RECOVERED_ID_WITH_ECC_CORRECTION,
+	   "Recovered id with ECC correction")
+
+SENSE_CODE(PARTIAL_DEFECT_LIST_TRANSFER,
+	   "Partial defect list transfer")
+
+SENSE_CODE(INVALID_COMMAND_OP_CODE,
+	   "Invalid command operation code")
+SENSE_CODE(ACCESS_DENIED_INITIATOR_PENDING_ENROLLED,
+	   "Access denied - initiator pending-enrolled")
+SENSE_CODE(ACCESS_DENIED_NO_ACCESS_RIGHTS,
+	   "Access denied - no access rights")
+SENSE_CODE(ACCESS_DENIED_INVALID_MGMT_ID_KEY,
+	   "Access denied - invalid mgmt id key")
+SENSE_CODE(ILLEGAL_COMMAND_WHILE_IN_WRITE_CAPABLE_STATE,
+	   "Illegal command while in write capable state")
+SENSE_CODE(0x2005,
+	   "Obsolete")
+SENSE_CODE(ILLEGAL_COMMAND_WHILE_IN_EXPLICIT_ADDRESS_MODE,
+	   "Illegal command while in explicit address mode")
+SENSE_CODE(ILLEGAL_COMMAND_WHILE_IN_IMPLICIT_ADDRESS_MODE,
+	   "Illegal command while in implicit address mode")
+SENSE_CODE(ACCESS_DENIED_ENROLLMENT_CONFLICT,
+	   "Access denied - enrollment conflict")
+SENSE_CODE(ACCESS_DENIED_INVALID_LU_IDENTIFIER,
+	   "Access denied - invalid LU identifier")
+SENSE_CODE(ACCESS_DENIED_INVALID_PROXY_TOKEN,
+	   "Access denied - invalid proxy token")
+SENSE_CODE(ACCESS_DENIED_ACL_LUN_CONFLICT,
+	   "Access denied - ACL LUN conflict")
+SENSE_CODE(ILLEGAL_COMMAND_WHEN_NOT_IN_APPEND_ONLY_MODE,
+	   "Illegal command when not in append-only mode")
+SENSE_CODE(NOT_AN_ADMINISTRATIVE_LOGICAL_UNIT,
+	   "Not an administrative logical unit")
+SENSE_CODE(NOT_A_SUBSIDIARY_LOGICAL_UNIT,
+	   "Not a subsidiary logical unit")
+SENSE_CODE(NOT_A_CONGLOMERATE_LOGICAL_UNIT,
+	   "Not a conglomerate logical unit")
+
+SENSE_CODE(LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE,
+	   "Logical block address out of range")
+SENSE_CODE(INVALID_ELEMENT_ADDRESS,
+	   "Invalid element address")
+SENSE_CODE(INVALID_ADDRESS_FOR_WRITE,
+	   "Invalid address for write")
+SENSE_CODE(INVALID_WRITE_CROSSING_LAYER_JUMP,
+	   "Invalid write crossing layer jump")
+SENSE_CODE(UNALIGNED_WRITE_COMMAND,
+	   "Unaligned write command")
+SENSE_CODE(WRITE_BOUNDARY_VIOLATION,
+	   "Write boundary violation")
+SENSE_CODE(ATTEMPT_TO_READ_INVALID_DATA,
+	   "Attempt to read invalid data")
+SENSE_CODE(READ_BOUNDARY_VIOLATION,
+	   "Read boundary violation")
+SENSE_CODE(MISALIGNED_WRITE_COMMAND,
+	   "Misaligned write command")
+SENSE_CODE(ATTEMPT_TO_ACCESS_GAP_ZONE,
+	   "Attempt to access gap zone")
+
+SENSE_CODE(ILLEGAL_FUNCTION,
+	   "Illegal function (use 20 00, 24 00, or 26 00)")
+
+SENSE_CODE(INVALID_TOKEN_OP,
+	   "Invalid token operation, cause not reportable")
+SENSE_CODE(INVALID_TOKEN_OP_UNSUPPORTED_TOKEN_TYPE,
+	   "Invalid token operation, unsupported token type")
+SENSE_CODE(INVALID_TOKEN_OP_REMOTE_TOKEN_USAGE_NOT_SUPPORTED,
+	   "Invalid token operation, remote token usage not supported")
+SENSE_CODE(INVALID_TOKEN_OP_REMOTE_ROD_TOKEN_CREATION_NOT_SUPPORTED,
+	   "Invalid token operation, remote rod token creation not supported")
+SENSE_CODE(INVALID_TOKEN_OP_TOKEN_UNKNOWN,
+	   "Invalid token operation, token unknown")
+SENSE_CODE(INVALID_TOKEN_OP_TOKEN_CORRUPT,
+	   "Invalid token operation, token corrupt")
+SENSE_CODE(INVALID_TOKEN_OP_TOKEN_REVOKED,
+	   "Invalid token operation, token revoked")
+SENSE_CODE(INVALID_TOKEN_OP_TOKEN_EXPIRED,
+	   "Invalid token operation, token expired")
+SENSE_CODE(INVALID_TOKEN_OP_TOKEN_CANCELLED,
+	   "Invalid token operation, token cancelled")
+SENSE_CODE(INVALID_TOKEN_OP_TOKEN_DELETED,
+	   "Invalid token operation, token deleted")
+SENSE_CODE(INVALID_TOKEN_OP_INVALID_TOKEN_LENGTH,
+	   "Invalid token operation, invalid token length")
+
+SENSE_CODE(INVALID_FIELD_IN_CDB,
+	   "Invalid field in cdb")
+SENSE_CODE(CDB_DECRYPTION_ERROR,
+	   "CDB decryption error")
+SENSE_CODE(0x2402,
+	   "Obsolete")
+SENSE_CODE(0x2403,
+	   "Obsolete")
+SENSE_CODE(SECURITY_AUDIT_VALUE_FROZEN,
+	   "Security audit value frozen")
+SENSE_CODE(SECURITY_WORKING_KEY_FROZEN,
+	   "Security working key frozen")
+SENSE_CODE(NONCE_NOT_UNIQUE,
+	   "Nonce not unique")
+SENSE_CODE(NONCE_TIMESTAMP_OUT_OF_RANGE,
+	   "Nonce timestamp out of range")
+SENSE_CODE(INVALID_XCDB,
+	   "Invalid XCDB")
+SENSE_CODE(INVALID_FAST_FORMAT,
+	   "Invalid fast format")
+
+SENSE_CODE(LU_NOT_SUPPORTED,
+	   "Logical unit not supported")
+
+SENSE_CODE(INVALID_FIELD_IN_PARAMETER_LIST,
+	   "Invalid field in parameter list")
+SENSE_CODE(PARAMETER_NOT_SUPPORTED,
+	   "Parameter not supported")
+SENSE_CODE(PARAMETER_VALUE_INVALID,
+	   "Parameter value invalid")
+SENSE_CODE(THRESHOLD_PARAMETERS_NOT_SUPPORTED,
+	   "Threshold parameters not supported")
+SENSE_CODE(INVALID_RELEASE_OF_PERSISTENT_RESERVATION,
+	   "Invalid release of persistent reservation")
+SENSE_CODE(DATA_DECRYPTION_ERROR,
+	   "Data decryption error")
+SENSE_CODE(TOO_MANY_TARGET_DESCRIPTORS,
+	   "Too many target descriptors")
+SENSE_CODE(UNSUPPORTED_TARGET_DESCRIPTOR_TYPE_CODE,
+	   "Unsupported target descriptor type code")
+SENSE_CODE(TOO_MANY_SEGMENT_DESCRIPTORS,
+	   "Too many segment descriptors")
+SENSE_CODE(UNSUPPORTED_SEGMENT_DESCRIPTOR_TYPE_CODE,
+	   "Unsupported segment descriptor type code")
+SENSE_CODE(UNEXPECTED_INEXACT_SEGMENT,
+	   "Unexpected inexact segment")
+SENSE_CODE(INLINE_DATA_LENGTH_EXCEEDED,
+	   "Inline data length exceeded")
+SENSE_CODE(INVALID_OP_FOR_COPY_SOURCE_OR_DESTINATION,
+	   "Invalid operation for copy source or destination")
+SENSE_CODE(COPY_SEGMENT_GRANULARITY_VIOLATION,
+	   "Copy segment granularity violation")
+SENSE_CODE(INVALID_PARAMETER_WHILE_PORT_IS_ENABLED,
+	   "Invalid parameter while port is enabled")
+SENSE_CODE(INVALID_DATA_OUT_BUFFER_INTEGRITY_CHECK_VALUE,
+	   "Invalid data-out buffer integrity check value")
+SENSE_CODE(DATA_DECRYPTION_KEY_FAIL_LIMIT_REACHED,
+	   "Data decryption key fail limit reached")
+SENSE_CODE(INCOMPLETE_KEY_ASSOCIATED_DATA_SET,
+	   "Incomplete key-associated data set")
+SENSE_CODE(VENDOR_SPECIFIC_KEY_REFERENCE_NOT_FOUND,
+	   "Vendor specific key reference not found")
+SENSE_CODE(APPLICATION_TAG_MODE_PAGE_IS_INVALID,
+	   "Application tag mode page is invalid")
+SENSE_CODE(TAPE_STREAM_MIRRORING_PREVENTED,
+	   "Tape stream mirroring prevented")
+SENSE_CODE(COPY_SOURCE_OR_COPY_DESTINATION_NOT_AUTHORIZED,
+	   "Copy source or copy destination not authorized")
+SENSE_CODE(FAST_COPY_NOT_POSSIBLE,
+	   "Fast copy not possible")
+
+SENSE_CODE(WRITE_PROTECTED,
+	   "Write protected")
+SENSE_CODE(HW_WRITE_PROTECTED,
+	   "Hardware write protected")
+SENSE_CODE(LU_SOFTWARE_WRITE_PROTECTED,
+	   "Logical unit software write protected")
+SENSE_CODE(ASSOCIATED_WRITE_PROTECT,
+	   "Associated write protect")
+SENSE_CODE(PERSISTENT_WRITE_PROTECT,
+	   "Persistent write protect")
+SENSE_CODE(PERMANENT_WRITE_PROTECT,
+	   "Permanent write protect")
+SENSE_CODE(CONDITIONAL_WRITE_PROTECT,
+	   "Conditional write protect")
+SENSE_CODE(SPACE_ALLOCATION_FAILED_WRITE_PROTECT,
+	   "Space allocation failed write protect")
+SENSE_CODE(ZONE_IS_READ_ONLY,
+	   "Zone is read only")
+
+SENSE_CODE(NOT_READY_TO_READY_CHANGE_MEDIUM_MAY_HAVE_CHANGED,
+	   "Not ready to ready change, medium may have changed")
+SENSE_CODE(IMPORT_OR_EXPORT_ELEMENT_ACCESSED,
+	   "Import or export element accessed")
+SENSE_CODE(FORMAT_LAYER_MAY_HAVE_CHANGED,
+	   "Format-layer may have changed")
+SENSE_CODE(IMPORT_EXPORT_ELEMENT_ACCESSED_MEDIUM_CHANGED,
+	   "Import/export element accessed, medium changed")
+
+SENSE_CODE(POWER_ON_RESET_OR_BUS_DEVICE_RESET_OCCURRED,
+	   "Power on, reset, or bus device reset occurred")
+SENSE_CODE(POWER_ON_OCCURRED,
+	   "Power on occurred")
+SENSE_CODE(SCSI_BUS_RESET_OCCURRED,
+	   "Scsi bus reset occurred")
+SENSE_CODE(BUS_DEVICE_RESET_FUNCTION_OCCURRED,
+	   "Bus device reset function occurred")
+SENSE_CODE(DEVICE_INTERNAL_RESET,
+	   "Device internal reset")
+SENSE_CODE(TRANSCEIVER_MODE_CHANGED_TO_SINGLE_ENDED,
+	   "Transceiver mode changed to single-ended")
+SENSE_CODE(TRANSCEIVER_MODE_CHANGED_TO_LVD,
+	   "Transceiver mode changed to lvd")
+SENSE_CODE(I_T_NEXUS_LOSS_OCCURRED,
+	   "I_T nexus loss occurred")
+
+SENSE_CODE(PARAMETERS_CHANGED,
+	   "Parameters changed")
+SENSE_CODE(MODE_PARAMETERS_CHANGED,
+	   "Mode parameters changed")
+SENSE_CODE(LOG_PARAMETERS_CHANGED,
+	   "Log parameters changed")
+SENSE_CODE(RESERVATIONS_PREEMPTED,
+	   "Reservations preempted")
+SENSE_CODE(RESERVATIONS_RELEASED,
+	   "Reservations released")
+SENSE_CODE(REGISTRATIONS_PREEMPTED,
+	   "Registrations preempted")
+SENSE_CODE(ASYMMETRIC_ACCESS_STATE_CHANGED,
+	   "Asymmetric access state changed")
+SENSE_CODE(IMPLICIT_ASYMMETRIC_ACCESS_STATE_TRANSITION_FAILED,
+	   "Implicit asymmetric access state transition failed")
+SENSE_CODE(PRIORITY_CHANGED,
+	   "Priority changed")
+SENSE_CODE(CAPACITY_DATA_HAS_CHANGED,
+	   "Capacity data has changed")
+SENSE_CODE(ERROR_HISTORY_I_T_NEXUS_CLEARED,
+	   "Error history I_T nexus cleared")
+SENSE_CODE(ERROR_HISTORY_SNAPSHOT_RELEASED,
+	   "Error history snapshot released")
+SENSE_CODE(ERROR_RECOVERY_ATTRIBUTES_HAVE_CHANGED,
+	   "Error recovery attributes have changed")
+SENSE_CODE(DATA_ENCRYPTION_CAPABILITIES_CHANGED,
+	   "Data encryption capabilities changed")
+SENSE_CODE(TIMESTAMP_CHANGED,
+	   "Timestamp changed")
+SENSE_CODE(DATA_ENCRYPTION_PARAMS_CHANGED_BY_ANOTHER_I_T_NEXUS,
+	   "Data encryption parameters changed by another i_t nexus")
+SENSE_CODE(DATA_ENCRYPTION_PARAMS_CHANGED_BY_VENDOR_SPECIFIC_EVENT,
+	   "Data encryption parameters changed by vendor specific event")
+SENSE_CODE(DATA_ENCRYPTION_KEY_INSTANCE_COUNTER_HAS_CHANGED,
+	   "Data encryption key instance counter has changed")
+SENSE_CODE(SA_CREATION_CAPABILITIES_DATA_HAS_CHANGED,
+	   "SA creation capabilities data has changed")
+SENSE_CODE(MEDIUM_REMOVAL_PREVENTION_PREEMPTED,
+	   "Medium removal prevention preempted")
+SENSE_CODE(ZONE_RESET_WRITE_POINTER_RECOMMENDED,
+	   "Zone reset write pointer recommended")
+
+SENSE_CODE(COPY_CANNOT_EXECUTE_SINCE_HOST_CANNOT_DISCONNECT,
+	   "Copy cannot execute since host cannot disconnect")
+
+SENSE_CODE(COMMAND_SEQUENCE_ERROR,
+	   "Command sequence error")
+SENSE_CODE(TOO_MANY_WINDOWS_SPECIFIED,
+	   "Too many windows specified")
+SENSE_CODE(INVALID_COMBINATION_OF_WINDOWS_SPECIFIED,
+	   "Invalid combination of windows specified")
+SENSE_CODE(CURRENT_PROGRAM_AREA_IS_NOT_EMPTY,
+	   "Current program area is not empty")
+SENSE_CODE(CURRENT_PROGRAM_AREA_IS_EMPTY,
+	   "Current program area is empty")
+SENSE_CODE(ILLEGAL_POWER_CONDITION_REQUEST,
+	   "Illegal power condition request")
+SENSE_CODE(PERSISTENT_PREVENT_CONFLICT,
+	   "Persistent prevent conflict")
+SENSE_CODE(PREVIOUS_BUSY_STATUS,
+	   "Previous busy status")
+SENSE_CODE(PREVIOUS_TASK_SET_FULL_STATUS,
+	   "Previous task set full status")
+SENSE_CODE(PREVIOUS_RESERVATION_CONFLICT_STATUS,
+	   "Previous reservation conflict status")
+SENSE_CODE(PARTITION_OR_COLLECTION_CONTAINS_USER_OBJECTS,
+	   "Partition or collection contains user objects")
+SENSE_CODE(NOT_RESERVED,
+	   "Not reserved")
+SENSE_CODE(ORWRITE_GENERATION_DOES_NOT_MATCH,
+	   "Orwrite generation does not match")
+SENSE_CODE(RESET_WRITE_POINTER_NOT_ALLOWED,
+	   "Reset write pointer not allowed")
+SENSE_CODE(ZONE_IS_OFFLINE,
+	   "Zone is offline")
+SENSE_CODE(STREAM_NOT_OPEN,
+	   "Stream not open")
+SENSE_CODE(UNWRITTEN_DATA_IN_ZONE,
+	   "Unwritten data in zone")
+SENSE_CODE(DESCRIPTOR_FORMAT_SENSE_DATA_REQUIRED,
+	   "Descriptor format sense data required")
+SENSE_CODE(ZONE_IS_INACTIVE,
+	   "Zone is inactive")
+SENSE_CODE(WELL_KNOWN_LU_ACCESS_REQUIRED,
+	   "Well known logical unit access required")
+
+SENSE_CODE(OVERWRITE_ERROR_ON_UPDATE_IN_PLACE,
+	   "Overwrite error on update in place")
+
+SENSE_CODE(INSUFFICIENT_TIME_FOR_OPERATION,
+	   "Insufficient time for operation")
+SENSE_CODE(COMMAND_TIMEOUT_BEFORE_PROCESSING,
+	   "Command timeout before processing")
+SENSE_CODE(COMMAND_TIMEOUT_DURING_PROCESSING,
+	   "Command timeout during processing")
+SENSE_CODE(COMMAND_TIMEOUT_DURING_PROCESSING_DUE_TO_ERROR_RECOVERY,
+	   "Command timeout during processing due to error recovery")
+
+SENSE_CODE(COMMANDS_CLEARED_BY_ANOTHER_INITIATOR,
+	   "Commands cleared by another initiator")
+SENSE_CODE(COMMANDS_CLEARED_BY_POWER_LOSS_NOTIFICATION,
+	   "Commands cleared by power loss notification")
+SENSE_CODE(COMMANDS_CLEARED_BY_DEVICE_SERVER,
+	   "Commands cleared by device server")
+SENSE_CODE(SOME_COMMANDS_CLEARED_BY_QUEUING_LAYER_EVENT,
+	   "Some commands cleared by queuing layer event")
+
+SENSE_CODE(INCOMPATIBLE_MEDIUM_INSTALLED,
+	   "Incompatible medium installed")
+SENSE_CODE(CANNOT_READ_MEDIUM_UNKNOWN_FORMAT,
+	   "Cannot read medium - unknown format")
+SENSE_CODE(CANNOT_READ_MEDIUM_INCOMPATIBLE_FORMAT,
+	   "Cannot read medium - incompatible format")
+SENSE_CODE(CLEANING_CARTRIDGE_INSTALLED,
+	   "Cleaning cartridge installed")
+SENSE_CODE(CANNOT_WRITE_MEDIUM_UNKNOWN_FORMAT,
+	   "Cannot write medium - unknown format")
+SENSE_CODE(CANNOT_WRITE_MEDIUM_INCOMPATIBLE_FORMAT,
+	   "Cannot write medium - incompatible format")
+SENSE_CODE(CANNOT_FORMAT_MEDIUM_INCOMPATIBLE_MEDIUM,
+	   "Cannot format medium - incompatible medium")
+SENSE_CODE(CLEANING_FAILURE,
+	   "Cleaning failure")
+SENSE_CODE(CANNOT_WRITE_APPLICATION_CODE_MISMATCH,
+	   "Cannot write - application code mismatch")
+SENSE_CODE(CURRENT_SESSION_NOT_FIXATED_FOR_APPEND,
+	   "Current session not fixated for append")
+SENSE_CODE(CLEANING_REQUEST_REJECTED,
+	   "Cleaning request rejected")
+SENSE_CODE(WORM_MEDIUM_OVERWRITE_ATTEMPTED,
+	   "WORM medium - overwrite attempted")
+SENSE_CODE(WORM_MEDIUM_INTEGRITY_CHECK,
+	   "WORM medium - integrity check")
+SENSE_CODE(MEDIUM_NOT_FORMATTED,
+	   "Medium not formatted")
+SENSE_CODE(INCOMPATIBLE_VOLUME_TYPE,
+	   "Incompatible volume type")
+SENSE_CODE(INCOMPATIBLE_VOLUME_QUALIFIER,
+	   "Incompatible volume qualifier")
+SENSE_CODE(CLEANING_VOLUME_EXPIRED,
+	   "Cleaning volume expired")
+
+SENSE_CODE(MEDIUM_FORMAT_CORRUPTED,
+	   "Medium format corrupted")
+SENSE_CODE(FORMAT_COMMAND_FAILED,
+	   "Format command failed")
+SENSE_CODE(ZONED_FORMATTING_FAILED_DUE_TO_SPARE_LINKING,
+	   "Zoned formatting failed due to spare linking")
+SENSE_CODE(SANITIZE_COMMAND_FAILED,
+	   "Sanitize command failed")
+SENSE_CODE(DEPOPULATION_FAILED,
+	   "Depopulation failed")
+SENSE_CODE(DEPOPULATION_RESTORATION_FAILED,
+	   "Depopulation restoration failed")
+
+SENSE_CODE(NO_DEFECT_SPARE_LOCATION_AVAILABLE,
+	   "No defect spare location available")
+SENSE_CODE(DEFECT_LIST_UPDATE_FAILURE,
+	   "Defect list update failure")
+
+SENSE_CODE(TAPE_LENGTH_ERROR,
+	   "Tape length error")
+
+SENSE_CODE(ENCLOSURE_FAILURE,
+	   "Enclosure failure")
+
+SENSE_CODE(ENCLOSURE_SERVICES_FAILURE,
+	   "Enclosure services failure")
+SENSE_CODE(UNSUPPORTED_ENCLOSURE_FUNCTION,
+	   "Unsupported enclosure function")
+SENSE_CODE(ENCLOSURE_SERVICES_UNAVAILABLE,
+	   "Enclosure services unavailable")
+SENSE_CODE(ENCLOSURE_SERVICES_TRANSFER_FAILURE,
+	   "Enclosure services transfer failure")
+SENSE_CODE(ENCLOSURE_SERVICES_TRANSFER_REFUSED,
+	   "Enclosure services transfer refused")
+SENSE_CODE(ENCLOSURE_SERVICES_CHECKSUM_ERROR,
+	   "Enclosure services checksum error")
+
+SENSE_CODE(RIBBON_INK_OR_TONER_FAILURE,
+	   "Ribbon, ink, or toner failure")
+
+SENSE_CODE(ROUNDED_PARAMETER,
+	   "Rounded parameter")
+
+SENSE_CODE(EVENT_STATUS_NOTIFICATION,
+	   "Event status notification")
+SENSE_CODE(ESN_POWER_MANAGEMENT_CLASS_EVENT,
+	   "Esn - power management class event")
+SENSE_CODE(ESN_MEDIA_CLASS_EVENT,
+	   "Esn - media class event")
+SENSE_CODE(ESN_DEVICE_BUSY_CLASS_EVENT,
+	   "Esn - device busy class event")
+SENSE_CODE(THIN_PROVISIONING_SOFT_THRESHOLD_REACHED,
+	   "Thin Provisioning soft threshold reached")
+SENSE_CODE(DEPOPULATION_INTERRUPTED,
+	   "Depopulation interrupted")
+SENSE_CODE(DEPOPULATION_RESTORATION_INTERRUPTED,
+	   "Depopulation restoration interrupted")
+
+SENSE_CODE(SAVING_PARAMETERS_NOT_SUPPORTED,
+	   "Saving parameters not supported")
+
+SENSE_CODE(MEDIUM_NOT_PRESENT,
+	   "Medium not present")
+SENSE_CODE(MEDIUM_NOT_PRESENT_TRAY_CLOSED,
+	   "Medium not present - tray closed")
+SENSE_CODE(MEDIUM_NOT_PRESENT_TRAY_OPEN,
+	   "Medium not present - tray open")
+SENSE_CODE(MEDIUM_NOT_PRESENT_LOADABLE,
+	   "Medium not present - loadable")
+SENSE_CODE(MEDIUM_NOT_PRESENT_MEDIUM_AUXILIARY_MEMORY_ACCESSIBLE,
+	   "Medium not present - medium auxiliary memory accessible")
+
+SENSE_CODE(SEQUENTIAL_POSITIONING_ERROR,
+	   "Sequential positioning error")
+SENSE_CODE(TAPE_POSITION_ERROR_AT_BEGINNING_OF_MEDIUM,
+	   "Tape position error at beginning-of-medium")
+SENSE_CODE(TAPE_POSITION_ERROR_AT_END_OF_MEDIUM,
+	   "Tape position error at end-of-medium")
+SENSE_CODE(TAPE_OR_ELECTRONIC_VERTICAL_FORMS_UNIT_NOT_READY,
+	   "Tape or electronic vertical forms unit not ready")
+SENSE_CODE(SLEW_FAILURE,
+	   "Slew failure")
+SENSE_CODE(PAPER_JAM,
+	   "Paper jam")
+SENSE_CODE(FAILED_TO_SENSE_TOP_OF_FORM,
+	   "Failed to sense top-of-form")
+SENSE_CODE(FAILED_TO_SENSE_BOTTOM_OF_FORM,
+	   "Failed to sense bottom-of-form")
+SENSE_CODE(REPOSITION_ERROR,
+	   "Reposition error")
+SENSE_CODE(READ_PAST_END_OF_MEDIUM,
+	   "Read past end of medium")
+SENSE_CODE(READ_PAST_BEGINNING_OF_MEDIUM,
+	   "Read past beginning of medium")
+SENSE_CODE(POSITION_PAST_END_OF_MEDIUM,
+	   "Position past end of medium")
+SENSE_CODE(POSITION_PAST_BEGINNING_OF_MEDIUM,
+	   "Position past beginning of medium")
+SENSE_CODE(MEDIUM_DESTINATION_ELEMENT_FULL,
+	   "Medium destination element full")
+SENSE_CODE(MEDIUM_SOURCE_ELEMENT_EMPTY,
+	   "Medium source element empty")
+SENSE_CODE(END_OF_MEDIUM_REACHED,
+	   "End of medium reached")
+SENSE_CODE(MEDIUM_MAGAZINE_NOT_ACCESSIBLE,
+	   "Medium magazine not accessible")
+SENSE_CODE(MEDIUM_MAGAZINE_REMOVED,
+	   "Medium magazine removed")
+SENSE_CODE(MEDIUM_MAGAZINE_INSERTED,
+	   "Medium magazine inserted")
+SENSE_CODE(MEDIUM_MAGAZINE_LOCKED,
+	   "Medium magazine locked")
+SENSE_CODE(MEDIUM_MAGAZINE_UNLOCKED,
+	   "Medium magazine unlocked")
+SENSE_CODE(MECHANICAL_POSITIONING_OR_CHANGER_ERROR,
+	   "Mechanical positioning or changer error")
+SENSE_CODE(READ_PAST_END_OF_USER_OBJECT,
+	   "Read past end of user object")
+SENSE_CODE(ELEMENT_DISABLED,
+	   "Element disabled")
+SENSE_CODE(ELEMENT_ENABLED,
+	   "Element enabled")
+SENSE_CODE(DATA_TRANSFER_DEVICE_REMOVED,
+	   "Data transfer device removed")
+SENSE_CODE(DATA_TRANSFER_DEVICE_INSERTED,
+	   "Data transfer device inserted")
+SENSE_CODE(TOO_MANY_LOGICAL_OBJECTS_ON_PARTITION_TO_SUPPORT_OP,
+	   "Too many logical objects on partition to support operation")
+SENSE_CODE(ELEMENT_STATIC_INFORMATION_CHANGED,
+	   "Element static information changed")
+
+SENSE_CODE(INVALID_BITS_IN_IDENTIFY_MESSAGE,
+	   "Invalid bits in identify message")
+
+SENSE_CODE(LU_HAS_NOT_SELF_CONFIGURED_YET,
+	   "Logical unit has not self-configured yet")
+SENSE_CODE(LU_FAILURE,
+	   "Logical unit failure")
+SENSE_CODE(TIMEOUT_ON_LOGICAL_UNIT,
+	   "Timeout on logical unit")
+SENSE_CODE(LU_FAILED_SELF_TEST,
+	   "Logical unit failed self-test")
+SENSE_CODE(LU_UNABLE_TO_UPDATE_SELFTEST_LOG,
+	   "Logical unit unable to update self-test log")
+
+SENSE_CODE(TARGET_OPERATING_CONDITIONS_HAVE_CHANGED,
+	   "Target operating conditions have changed")
+SENSE_CODE(MICROCODE_HAS_BEEN_CHANGED,
+	   "Microcode has been changed")
+SENSE_CODE(CHANGED_OPERATING_DEFINITION,
+	   "Changed operating definition")
+SENSE_CODE(INQUIRY_DATA_HAS_CHANGED,
+	   "Inquiry data has changed")
+SENSE_CODE(COMPONENT_DEVICE_ATTACHED,
+	   "Component device attached")
+SENSE_CODE(DEVICE_IDENTIFIER_CHANGED,
+	   "Device identifier changed")
+SENSE_CODE(REDUNDANCY_GROUP_CREATED_OR_MODIFIED,
+	   "Redundancy group created or modified")
+SENSE_CODE(REDUNDANCY_GROUP_DELETED,
+	   "Redundancy group deleted")
+SENSE_CODE(SPARE_CREATED_OR_MODIFIED,
+	   "Spare created or modified")
+SENSE_CODE(SPARE_DELETED,
+	   "Spare deleted")
+SENSE_CODE(VOLUME_SET_CREATED_OR_MODIFIED,
+	   "Volume set created or modified")
+SENSE_CODE(VOLUME_SET_DELETED,
+	   "Volume set deleted")
+SENSE_CODE(VOLUME_SET_DEASSIGNED,
+	   "Volume set deassigned")
+SENSE_CODE(VOLUME_SET_REASSIGNED,
+	   "Volume set reassigned")
+SENSE_CODE(REPORTED_LUNS_DATA_HAS_CHANGED,
+	   "Reported luns data has changed")
+SENSE_CODE(ECHO_BUFFER_OVERWRITTEN,
+	   "Echo buffer overwritten")
+SENSE_CODE(MEDIUM_LOADABLE,
+	   "Medium loadable")
+SENSE_CODE(MEDIUM_AUXILIARY_MEMORY_ACCESSIBLE,
+	   "Medium auxiliary memory accessible")
+SENSE_CODE(iSCSI_IP_ADDRESS_ADDED,
+	   "iSCSI IP address added")
+SENSE_CODE(iSCSI_IP_ADDRESS_REMOVED,
+	   "iSCSI IP address removed")
+SENSE_CODE(iSCSI_IP_ADDRESS_CHANGED,
+	   "iSCSI IP address changed")
+SENSE_CODE(INSPECT_REFERRALS_SENSE_DESCRIPTORS,
+	   "Inspect referrals sense descriptors")
+SENSE_CODE(MICROCODE_HAS_BEEN_CHANGED_WITHOUT_RESET,
+	   "Microcode has been changed without reset")
+SENSE_CODE(ZONE_TRANSITION_TO_FULL,
+	   "Zone transition to full")
+SENSE_CODE(BIND_COMPLETED,
+	   "Bind completed")
+SENSE_CODE(BIND_REDIRECTED,
+	   "Bind redirected")
+SENSE_CODE(SUBSIDIARY_BINDING_CHANGED,
+	   "Subsidiary binding changed")
 
 /*
- *	SENSE_CODE(0x40NN, "Ram failure")
- *	SENSE_CODE(0x40NN, "Diagnostic failure on component nn")
- *	SENSE_CODE(0x41NN, "Data path failure")
- *	SENSE_CODE(0x42NN, "Power-on or self-test failure")
+ * SENSE_CODE(0x40NN, "Ram failure")
+ * SENSE_CODE(0x40NN, "Diagnostic failure on component nn")
+ *
+ * SENSE_CODE(0x41NN, "Data path failure")
+ *
+ * SENSE_CODE(0x42NN, "Power-on or self-test failure")
  */
-SENSE_CODE(0x4300, "Message error")
-
-SENSE_CODE(0x4400, "Internal target failure")
-SENSE_CODE(0x4401, "Persistent reservation information lost")
-SENSE_CODE(0x4471, "ATA device failed set features")
-
-SENSE_CODE(0x4500, "Select or reselect failure")
-
-SENSE_CODE(0x4600, "Unsuccessful soft reset")
-
-SENSE_CODE(0x4700, "Scsi parity error")
-SENSE_CODE(0x4701, "Data phase CRC error detected")
-SENSE_CODE(0x4702, "Scsi parity error detected during st data phase")
-SENSE_CODE(0x4703, "Information unit iuCRC error detected")
-SENSE_CODE(0x4704, "Asynchronous information protection error detected")
-SENSE_CODE(0x4705, "Protocol service CRC error")
-SENSE_CODE(0x4706, "Phy test function in progress")
-SENSE_CODE(0x477f, "Some commands cleared by iSCSI Protocol event")
-
-SENSE_CODE(0x4800, "Initiator detected error message received")
-
-SENSE_CODE(0x4900, "Invalid message error")
-
-SENSE_CODE(0x4A00, "Command phase error")
-
-SENSE_CODE(0x4B00, "Data phase error")
-SENSE_CODE(0x4B01, "Invalid target port transfer tag received")
-SENSE_CODE(0x4B02, "Too much write data")
-SENSE_CODE(0x4B03, "Ack/nak timeout")
-SENSE_CODE(0x4B04, "Nak received")
-SENSE_CODE(0x4B05, "Data offset error")
-SENSE_CODE(0x4B06, "Initiator response timeout")
-SENSE_CODE(0x4B07, "Connection lost")
-SENSE_CODE(0x4B08, "Data-in buffer overflow - data buffer size")
-SENSE_CODE(0x4B09, "Data-in buffer overflow - data buffer descriptor area")
-SENSE_CODE(0x4B0A, "Data-in buffer error")
-SENSE_CODE(0x4B0B, "Data-out buffer overflow - data buffer size")
-SENSE_CODE(0x4B0C, "Data-out buffer overflow - data buffer descriptor area")
-SENSE_CODE(0x4B0D, "Data-out buffer error")
-SENSE_CODE(0x4B0E, "PCIe fabric error")
-SENSE_CODE(0x4B0F, "PCIe completion timeout")
-SENSE_CODE(0x4B10, "PCIe completer abort")
-SENSE_CODE(0x4B11, "PCIe poisoned tlp received")
-SENSE_CODE(0x4B12, "PCIe eCRC check failed")
-SENSE_CODE(0x4B13, "PCIe unsupported request")
-SENSE_CODE(0x4B14, "PCIe acs violation")
-SENSE_CODE(0x4B15, "PCIe tlp prefix blocked")
-
-SENSE_CODE(0x4C00, "Logical unit failed self-configuration")
+
+SENSE_CODE(MESSAGE_ERROR,
+	   "Message error")
+
+SENSE_CODE(INTERNAL_TARGET_FAILURE,
+	   "Internal target failure")
+SENSE_CODE(PERSISTENT_RESERVATION_INFORMATION_LOST,
+	   "Persistent reservation information lost")
+SENSE_CODE(ATA_DEVICE_FAILED_SET_FEATURES,
+	   "ATA device failed set features")
+
+SENSE_CODE(SELECT_OR_RESELECT_FAILURE,
+	   "Select or reselect failure")
+
+SENSE_CODE(UNSUCCESSFUL_SOFT_RESET,
+	   "Unsuccessful soft reset")
+
+SENSE_CODE(SCSI_PARITY_ERROR,
+	   "Scsi parity error")
+SENSE_CODE(DATA_PHASE_CRC_ERROR_DETECTED,
+	   "Data phase CRC error detected")
+SENSE_CODE(SCSI_PARITY_ERROR_DETECTED_DURING_ST_DATA_PHASE,
+	   "Scsi parity error detected during st data phase")
+SENSE_CODE(INFORMATION_UNIT_iuCRC_ERROR_DETECTED,
+	   "Information unit iuCRC error detected")
+SENSE_CODE(ASYNCHRONOUS_INFORMATION_PROTECTION_ERROR_DETECTED,
+	   "Asynchronous information protection error detected")
+SENSE_CODE(PROTOCOL_SERVICE_CRC_ERROR,
+	   "Protocol service CRC error")
+SENSE_CODE(PHY_TEST_FUNCTION_IN_PROGRESS,
+	   "Phy test function in progress")
+SENSE_CODE(SOME_COMMANDS_CLEARED_BY_ISCSI_PROTOCOL_EVENT,
+	   "Some commands cleared by iSCSI Protocol event")
+
+SENSE_CODE(INITIATOR_DETECTED_ERROR_MESSAGE_RECEIVED,
+	   "Initiator detected error message received")
+
+SENSE_CODE(INVALID_MESSAGE_ERROR,
+	   "Invalid message error")
+
+SENSE_CODE(COMMAND_PHASE_ERROR,
+	   "Command phase error")
+
+SENSE_CODE(DATA_PHASE_ERROR,
+	   "Data phase error")
+SENSE_CODE(INVALID_TARGET_PORT_TRANSFER_TAG_RECEIVED,
+	   "Invalid target port transfer tag received")
+SENSE_CODE(TOO_MUCH_WRITE_DATA,
+	   "Too much write data")
+SENSE_CODE(ACK_NAK_TIMEOUT,
+	   "Ack/nak timeout")
+SENSE_CODE(NAK_RECEIVED,
+	   "Nak received")
+SENSE_CODE(DATA_OFFSET_ERROR,
+	   "Data offset error")
+SENSE_CODE(INITIATOR_RESPONSE_TIMEOUT,
+	   "Initiator response timeout")
+SENSE_CODE(CONNECTION_LOST,
+	   "Connection lost")
+SENSE_CODE(DATA_IN_BUFFER_OVERFLOW_BUFFER_SIZE,
+	   "Data-in buffer overflow - data buffer size")
+SENSE_CODE(DATA_IN_BUFFER_OVERFLOW_BUFFER_DESCRIPTOR_AREA,
+	   "Data-in buffer overflow - data buffer descriptor area")
+SENSE_CODE(DATA_IN_BUFFER_ERROR,
+	   "Data-in buffer error")
+SENSE_CODE(DATA_OUT_BUFFER_OVERFLOW_BUFFER_SIZE,
+	   "Data-out buffer overflow - data buffer size")
+SENSE_CODE(DATA_OUT_BUFFER_OVERFLOW_BUFFER_DESCRIPTOR_AREA,
+	   "Data-out buffer overflow - data buffer descriptor area")
+SENSE_CODE(DATA_OUT_BUFFER_ERROR,
+	   "Data-out buffer error")
+SENSE_CODE(PCIE_FABRIC_ERROR,
+	   "PCIe fabric error")
+SENSE_CODE(PCIE_COMPLETION_TIMEOUT,
+	   "PCIe completion timeout")
+SENSE_CODE(PCIE_COMPLETER_ABORT,
+	   "PCIe completer abort")
+SENSE_CODE(PCIE_POISONED_TLP_RECEIVED,
+	   "PCIe poisoned tlp received")
+SENSE_CODE(PCIE_ECRC_CHECK_FAILED,
+	   "PCIe eCRC check failed")
+SENSE_CODE(PCIE_UNSUPPORTED_REQUEST,
+	   "PCIe unsupported request")
+SENSE_CODE(PCIE_ACS_VIOLATION,
+	   "PCIe acs violation")
+SENSE_CODE(PCIE_TLP_PREFIX_BLOCKED,
+	   "PCIe tlp prefix blocked")
+
+SENSE_CODE(LU_FAILED_SELF_CONFIGURATION,
+	   "Logical unit failed self-configuration")
+
 /*
- *	SENSE_CODE(0x4DNN, "Tagged overlapped commands (nn = queue tag)")
+ * SENSE_CODE(0x4DNN, "Tagged overlapped commands (nn = queue tag)")
  */
-SENSE_CODE(0x4E00, "Overlapped commands attempted")
-
-SENSE_CODE(0x5000, "Write append error")
-SENSE_CODE(0x5001, "Write append position error")
-SENSE_CODE(0x5002, "Position error related to timing")
-
-SENSE_CODE(0x5100, "Erase failure")
-SENSE_CODE(0x5101, "Erase failure - incomplete erase operation detected")
-
-SENSE_CODE(0x5200, "Cartridge fault")
-
-SENSE_CODE(0x5300, "Media load or eject failed")
-SENSE_CODE(0x5301, "Unload tape failure")
-SENSE_CODE(0x5302, "Medium removal prevented")
-SENSE_CODE(0x5303, "Medium removal prevented by data transfer element")
-SENSE_CODE(0x5304, "Medium thread or unthread failure")
-SENSE_CODE(0x5305, "Volume identifier invalid")
-SENSE_CODE(0x5306, "Volume identifier missing")
-SENSE_CODE(0x5307, "Duplicate volume identifier")
-SENSE_CODE(0x5308, "Element status unknown")
-SENSE_CODE(0x5309, "Data transfer device error - load failed")
-SENSE_CODE(0x530a, "Data transfer device error - unload failed")
-SENSE_CODE(0x530b, "Data transfer device error - unload missing")
-SENSE_CODE(0x530c, "Data transfer device error - eject failed")
-SENSE_CODE(0x530d, "Data transfer device error - library communication failed")
-
-SENSE_CODE(0x5400, "Scsi to host system interface failure")
-
-SENSE_CODE(0x5500, "System resource failure")
-SENSE_CODE(0x5501, "System buffer full")
-SENSE_CODE(0x5502, "Insufficient reservation resources")
-SENSE_CODE(0x5503, "Insufficient resources")
-SENSE_CODE(0x5504, "Insufficient registration resources")
-SENSE_CODE(0x5505, "Insufficient access control resources")
-SENSE_CODE(0x5506, "Auxiliary memory out of space")
-SENSE_CODE(0x5507, "Quota error")
-SENSE_CODE(0x5508, "Maximum number of supplemental decryption keys exceeded")
-SENSE_CODE(0x5509, "Medium auxiliary memory not accessible")
-SENSE_CODE(0x550A, "Data currently unavailable")
-SENSE_CODE(0x550B, "Insufficient power for operation")
-SENSE_CODE(0x550C, "Insufficient resources to create rod")
-SENSE_CODE(0x550D, "Insufficient resources to create rod token")
-SENSE_CODE(0x550E, "Insufficient zone resources")
-SENSE_CODE(0x550F, "Insufficient zone resources to complete write")
-SENSE_CODE(0x5510, "Maximum number of streams open")
-SENSE_CODE(0x5511, "Insufficient resources to bind")
-
-SENSE_CODE(0x5700, "Unable to recover table-of-contents")
-
-SENSE_CODE(0x5800, "Generation does not exist")
-
-SENSE_CODE(0x5900, "Updated block read")
-
-SENSE_CODE(0x5A00, "Operator request or state change input")
-SENSE_CODE(0x5A01, "Operator medium removal request")
-SENSE_CODE(0x5A02, "Operator selected write protect")
-SENSE_CODE(0x5A03, "Operator selected write permit")
-
-SENSE_CODE(0x5B00, "Log exception")
-SENSE_CODE(0x5B01, "Threshold condition met")
-SENSE_CODE(0x5B02, "Log counter at maximum")
-SENSE_CODE(0x5B03, "Log list codes exhausted")
-
-SENSE_CODE(0x5C00, "Rpl status change")
-SENSE_CODE(0x5C01, "Spindles synchronized")
-SENSE_CODE(0x5C02, "Spindles not synchronized")
-
-SENSE_CODE(0x5D00, "Failure prediction threshold exceeded")
-SENSE_CODE(0x5D01, "Media failure prediction threshold exceeded")
-SENSE_CODE(0x5D02, "Logical unit failure prediction threshold exceeded")
-SENSE_CODE(0x5D03, "Spare area exhaustion prediction threshold exceeded")
-SENSE_CODE(0x5D10, "Hardware impending failure general hard drive failure")
-SENSE_CODE(0x5D11, "Hardware impending failure drive error rate too high")
-SENSE_CODE(0x5D12, "Hardware impending failure data error rate too high")
-SENSE_CODE(0x5D13, "Hardware impending failure seek error rate too high")
-SENSE_CODE(0x5D14, "Hardware impending failure too many block reassigns")
-SENSE_CODE(0x5D15, "Hardware impending failure access times too high")
-SENSE_CODE(0x5D16, "Hardware impending failure start unit times too high")
-SENSE_CODE(0x5D17, "Hardware impending failure channel parametrics")
-SENSE_CODE(0x5D18, "Hardware impending failure controller detected")
-SENSE_CODE(0x5D19, "Hardware impending failure throughput performance")
-SENSE_CODE(0x5D1A, "Hardware impending failure seek time performance")
-SENSE_CODE(0x5D1B, "Hardware impending failure spin-up retry count")
-SENSE_CODE(0x5D1C, "Hardware impending failure drive calibration retry count")
-SENSE_CODE(0x5D20, "Controller impending failure general hard drive failure")
-SENSE_CODE(0x5D21, "Controller impending failure drive error rate too high")
-SENSE_CODE(0x5D22, "Controller impending failure data error rate too high")
-SENSE_CODE(0x5D23, "Controller impending failure seek error rate too high")
-SENSE_CODE(0x5D24, "Controller impending failure too many block reassigns")
-SENSE_CODE(0x5D25, "Controller impending failure access times too high")
-SENSE_CODE(0x5D26, "Controller impending failure start unit times too high")
-SENSE_CODE(0x5D27, "Controller impending failure channel parametrics")
-SENSE_CODE(0x5D28, "Controller impending failure controller detected")
-SENSE_CODE(0x5D29, "Controller impending failure throughput performance")
-SENSE_CODE(0x5D2A, "Controller impending failure seek time performance")
-SENSE_CODE(0x5D2B, "Controller impending failure spin-up retry count")
-SENSE_CODE(0x5D2C, "Controller impending failure drive calibration retry count")
-SENSE_CODE(0x5D30, "Data channel impending failure general hard drive failure")
-SENSE_CODE(0x5D31, "Data channel impending failure drive error rate too high")
-SENSE_CODE(0x5D32, "Data channel impending failure data error rate too high")
-SENSE_CODE(0x5D33, "Data channel impending failure seek error rate too high")
-SENSE_CODE(0x5D34, "Data channel impending failure too many block reassigns")
-SENSE_CODE(0x5D35, "Data channel impending failure access times too high")
-SENSE_CODE(0x5D36, "Data channel impending failure start unit times too high")
-SENSE_CODE(0x5D37, "Data channel impending failure channel parametrics")
-SENSE_CODE(0x5D38, "Data channel impending failure controller detected")
-SENSE_CODE(0x5D39, "Data channel impending failure throughput performance")
-SENSE_CODE(0x5D3A, "Data channel impending failure seek time performance")
-SENSE_CODE(0x5D3B, "Data channel impending failure spin-up retry count")
-SENSE_CODE(0x5D3C, "Data channel impending failure drive calibration retry count")
-SENSE_CODE(0x5D40, "Servo impending failure general hard drive failure")
-SENSE_CODE(0x5D41, "Servo impending failure drive error rate too high")
-SENSE_CODE(0x5D42, "Servo impending failure data error rate too high")
-SENSE_CODE(0x5D43, "Servo impending failure seek error rate too high")
-SENSE_CODE(0x5D44, "Servo impending failure too many block reassigns")
-SENSE_CODE(0x5D45, "Servo impending failure access times too high")
-SENSE_CODE(0x5D46, "Servo impending failure start unit times too high")
-SENSE_CODE(0x5D47, "Servo impending failure channel parametrics")
-SENSE_CODE(0x5D48, "Servo impending failure controller detected")
-SENSE_CODE(0x5D49, "Servo impending failure throughput performance")
-SENSE_CODE(0x5D4A, "Servo impending failure seek time performance")
-SENSE_CODE(0x5D4B, "Servo impending failure spin-up retry count")
-SENSE_CODE(0x5D4C, "Servo impending failure drive calibration retry count")
-SENSE_CODE(0x5D50, "Spindle impending failure general hard drive failure")
-SENSE_CODE(0x5D51, "Spindle impending failure drive error rate too high")
-SENSE_CODE(0x5D52, "Spindle impending failure data error rate too high")
-SENSE_CODE(0x5D53, "Spindle impending failure seek error rate too high")
-SENSE_CODE(0x5D54, "Spindle impending failure too many block reassigns")
-SENSE_CODE(0x5D55, "Spindle impending failure access times too high")
-SENSE_CODE(0x5D56, "Spindle impending failure start unit times too high")
-SENSE_CODE(0x5D57, "Spindle impending failure channel parametrics")
-SENSE_CODE(0x5D58, "Spindle impending failure controller detected")
-SENSE_CODE(0x5D59, "Spindle impending failure throughput performance")
-SENSE_CODE(0x5D5A, "Spindle impending failure seek time performance")
-SENSE_CODE(0x5D5B, "Spindle impending failure spin-up retry count")
-SENSE_CODE(0x5D5C, "Spindle impending failure drive calibration retry count")
-SENSE_CODE(0x5D60, "Firmware impending failure general hard drive failure")
-SENSE_CODE(0x5D61, "Firmware impending failure drive error rate too high")
-SENSE_CODE(0x5D62, "Firmware impending failure data error rate too high")
-SENSE_CODE(0x5D63, "Firmware impending failure seek error rate too high")
-SENSE_CODE(0x5D64, "Firmware impending failure too many block reassigns")
-SENSE_CODE(0x5D65, "Firmware impending failure access times too high")
-SENSE_CODE(0x5D66, "Firmware impending failure start unit times too high")
-SENSE_CODE(0x5D67, "Firmware impending failure channel parametrics")
-SENSE_CODE(0x5D68, "Firmware impending failure controller detected")
-SENSE_CODE(0x5D69, "Firmware impending failure throughput performance")
-SENSE_CODE(0x5D6A, "Firmware impending failure seek time performance")
-SENSE_CODE(0x5D6B, "Firmware impending failure spin-up retry count")
-SENSE_CODE(0x5D6C, "Firmware impending failure drive calibration retry count")
-SENSE_CODE(0x5D73, "Media impending failure endurance limit met")
-SENSE_CODE(0x5DFF, "Failure prediction threshold exceeded (false)")
-
-SENSE_CODE(0x5E00, "Low power condition on")
-SENSE_CODE(0x5E01, "Idle condition activated by timer")
-SENSE_CODE(0x5E02, "Standby condition activated by timer")
-SENSE_CODE(0x5E03, "Idle condition activated by command")
-SENSE_CODE(0x5E04, "Standby condition activated by command")
-SENSE_CODE(0x5E05, "Idle_b condition activated by timer")
-SENSE_CODE(0x5E06, "Idle_b condition activated by command")
-SENSE_CODE(0x5E07, "Idle_c condition activated by timer")
-SENSE_CODE(0x5E08, "Idle_c condition activated by command")
-SENSE_CODE(0x5E09, "Standby_y condition activated by timer")
-SENSE_CODE(0x5E0A, "Standby_y condition activated by command")
-SENSE_CODE(0x5E41, "Power state change to active")
-SENSE_CODE(0x5E42, "Power state change to idle")
-SENSE_CODE(0x5E43, "Power state change to standby")
-SENSE_CODE(0x5E45, "Power state change to sleep")
-SENSE_CODE(0x5E47, "Power state change to device control")
-
-SENSE_CODE(0x6000, "Lamp failure")
-
-SENSE_CODE(0x6100, "Video acquisition error")
-SENSE_CODE(0x6101, "Unable to acquire video")
-SENSE_CODE(0x6102, "Out of focus")
-
-SENSE_CODE(0x6200, "Scan head positioning error")
-
-SENSE_CODE(0x6300, "End of user area encountered on this track")
-SENSE_CODE(0x6301, "Packet does not fit in available space")
-
-SENSE_CODE(0x6400, "Illegal mode for this track")
-SENSE_CODE(0x6401, "Invalid packet size")
-
-SENSE_CODE(0x6500, "Voltage fault")
-
-SENSE_CODE(0x6600, "Automatic document feeder cover up")
-SENSE_CODE(0x6601, "Automatic document feeder lift up")
-SENSE_CODE(0x6602, "Document jam in automatic document feeder")
-SENSE_CODE(0x6603, "Document miss feed automatic in document feeder")
-
-SENSE_CODE(0x6700, "Configuration failure")
-SENSE_CODE(0x6701, "Configuration of incapable logical units failed")
-SENSE_CODE(0x6702, "Add logical unit failed")
-SENSE_CODE(0x6703, "Modification of logical unit failed")
-SENSE_CODE(0x6704, "Exchange of logical unit failed")
-SENSE_CODE(0x6705, "Remove of logical unit failed")
-SENSE_CODE(0x6706, "Attachment of logical unit failed")
-SENSE_CODE(0x6707, "Creation of logical unit failed")
-SENSE_CODE(0x6708, "Assign failure occurred")
-SENSE_CODE(0x6709, "Multiply assigned logical unit")
-SENSE_CODE(0x670A, "Set target port groups command failed")
-SENSE_CODE(0x670B, "ATA device feature not enabled")
-SENSE_CODE(0x670C, "Command rejected")
-SENSE_CODE(0x670D, "Explicit bind not allowed")
-
-SENSE_CODE(0x6800, "Logical unit not configured")
-SENSE_CODE(0x6801, "Subsidiary logical unit not configured")
-
-SENSE_CODE(0x6900, "Data loss on logical unit")
-SENSE_CODE(0x6901, "Multiple logical unit failures")
-SENSE_CODE(0x6902, "Parity/data mismatch")
-
-SENSE_CODE(0x6A00, "Informational, refer to log")
-
-SENSE_CODE(0x6B00, "State change has occurred")
-SENSE_CODE(0x6B01, "Redundancy level got better")
-SENSE_CODE(0x6B02, "Redundancy level got worse")
-
-SENSE_CODE(0x6C00, "Rebuild failure occurred")
-
-SENSE_CODE(0x6D00, "Recalculate failure occurred")
-
-SENSE_CODE(0x6E00, "Command to logical unit failed")
-
-SENSE_CODE(0x6F00, "Copy protection key exchange failure - authentication failure")
-SENSE_CODE(0x6F01, "Copy protection key exchange failure - key not present")
-SENSE_CODE(0x6F02, "Copy protection key exchange failure - key not established")
-SENSE_CODE(0x6F03, "Read of scrambled sector without authentication")
-SENSE_CODE(0x6F04, "Media region code is mismatched to logical unit region")
-SENSE_CODE(0x6F05, "Drive region must be permanent/region reset count error")
-SENSE_CODE(0x6F06, "Insufficient block count for binding nonce recording")
-SENSE_CODE(0x6F07, "Conflict in binding nonce recording")
-SENSE_CODE(0x6F08, "Insufficient permission")
-SENSE_CODE(0x6F09, "Invalid drive-host pairing server")
-SENSE_CODE(0x6F0A, "Drive-host pairing suspended")
+
+SENSE_CODE(OVERLAPPED_COMMANDS_ATTEMPTED,
+	   "Overlapped commands attempted")
+
+SENSE_CODE(WRITE_APPEND_ERROR,
+	   "Write append error")
+SENSE_CODE(WRITE_APPEND_POSITION_ERROR,
+	   "Write append position error")
+SENSE_CODE(POSITION_ERROR_RELATED_TO_TIMING,
+	   "Position error related to timing")
+
+SENSE_CODE(ERASE_FAILURE,
+	   "Erase failure")
+SENSE_CODE(ERASE_FAILURE_INCOMPLETE_ERASE_OP_DETECTED,
+	   "Erase failure - incomplete erase operation detected")
+
+SENSE_CODE(CARTRIDGE_FAULT,
+	   "Cartridge fault")
+
+SENSE_CODE(MEDIA_LOAD_OR_EJECT_FAILED,
+	   "Media load or eject failed")
+SENSE_CODE(UNLOAD_TAPE_FAILURE,
+	   "Unload tape failure")
+SENSE_CODE(MEDIUM_REMOVAL_PREVENTED,
+	   "Medium removal prevented")
+SENSE_CODE(MEDIUM_REMOVAL_PREVENTED_BY_DATA_TRANSFER_ELEMENT,
+	   "Medium removal prevented by data transfer element")
+SENSE_CODE(MEDIUM_THREAD_OR_UNTHREAD_FAILURE,
+	   "Medium thread or unthread failure")
+SENSE_CODE(VOLUME_IDENTIFIER_INVALID,
+	   "Volume identifier invalid")
+SENSE_CODE(VOLUME_IDENTIFIER_MISSING,
+	   "Volume identifier missing")
+SENSE_CODE(DUPLICATE_VOLUME_IDENTIFIER,
+	   "Duplicate volume identifier")
+SENSE_CODE(ELEMENT_STATUS_UNKNOWN,
+	   "Element status unknown")
+SENSE_CODE(DATA_TRANSFER_DEVICE_ERR_LOAD_FAILED,
+	   "Data transfer device error - load failed")
+SENSE_CODE(DATA_TRANSFER_DEVICE_ERR_UNLOAD_FAILED,
+	   "Data transfer device error - unload failed")
+SENSE_CODE(DATA_TRANSFER_DEVICE_ERR_UNLOAD_MISSING,
+	   "Data transfer device error - unload missing")
+SENSE_CODE(DATA_TRANSFER_DEVICE_ERR_EJECT_FAILED,
+	   "Data transfer device error - eject failed")
+SENSE_CODE(DATA_TRANSFER_DEVICE_ERR_LIBRARY_COMMUNICATION_FAILED,
+	   "Data transfer device error - library communication failed")
+
+SENSE_CODE(SCSI_TO_HOST_SYSTEM_INTERFACE_FAILURE,
+	   "Scsi to host system interface failure")
+
+SENSE_CODE(SYSTEM_RESOURCE_FAILURE,
+	   "System resource failure")
+SENSE_CODE(SYSTEM_BUFFER_FULL,
+	   "System buffer full")
+SENSE_CODE(INSUFFICIENT_RESERVATION_RESOURCES,
+	   "Insufficient reservation resources")
+SENSE_CODE(INSUFFICIENT_RESOURCES,
+	   "Insufficient resources")
+SENSE_CODE(INSUFFICIENT_REGISTRATION_RESOURCES,
+	   "Insufficient registration resources")
+SENSE_CODE(INSUFFICIENT_ACCESS_CONTROL_RESOURCES,
+	   "Insufficient access control resources")
+SENSE_CODE(AUXILIARY_MEMORY_OUT_OF_SPACE,
+	   "Auxiliary memory out of space")
+SENSE_CODE(QUOTA_ERROR,
+	   "Quota error")
+SENSE_CODE(MAXIMUM_NUMBER_OF_SUPPLEMENTAL_DECRYPTION_KEYS_EXCEEDED,
+	   "Maximum number of supplemental decryption keys exceeded")
+SENSE_CODE(MEDIUM_AUXILIARY_MEMORY_NOT_ACCESSIBLE,
+	   "Medium auxiliary memory not accessible")
+SENSE_CODE(DATA_CURRENTLY_UNAVAILABLE,
+	   "Data currently unavailable")
+SENSE_CODE(INSUFFICIENT_POWER_FOR_OPERATION,
+	   "Insufficient power for operation")
+SENSE_CODE(INSUFFICIENT_RESOURCES_TO_CREATE_ROD,
+	   "Insufficient resources to create rod")
+SENSE_CODE(INSUFFICIENT_RESOURCES_TO_CREATE_ROD_TOKEN,
+	   "Insufficient resources to create rod token")
+SENSE_CODE(INSUFFICIENT_ZONE_RESOURCES,
+	   "Insufficient zone resources")
+SENSE_CODE(INSUFFICIENT_ZONE_RESOURCES_TO_COMPLETE_WRITE,
+	   "Insufficient zone resources to complete write")
+SENSE_CODE(MAXIMUM_NUMBER_OF_STREAMS_OPEN,
+	   "Maximum number of streams open")
+SENSE_CODE(INSUFFICIENT_RESOURCES_TO_BIND,
+	   "Insufficient resources to bind")
+
+SENSE_CODE(UNABLE_TO_RECOVER_TABLE_OF_CONTENTS,
+	   "Unable to recover table-of-contents")
+
+SENSE_CODE(GENERATION_DOES_NOT_EXIST,
+	   "Generation does not exist")
+
+SENSE_CODE(UPDATED_BLOCK_READ,
+	   "Updated block read")
+
+SENSE_CODE(OPERATOR_REQUEST_OR_STATE_CHANGE_INPUT,
+	   "Operator request or state change input")
+SENSE_CODE(OPERATOR_MEDIUM_REMOVAL_REQUEST,
+	   "Operator medium removal request")
+SENSE_CODE(OPERATOR_SELECTED_WRITE_PROTECT,
+	   "Operator selected write protect")
+SENSE_CODE(OPERATOR_SELECTED_WRITE_PERMIT,
+	   "Operator selected write permit")
+
+SENSE_CODE(LOG_EXCEPTION,
+	   "Log exception")
+SENSE_CODE(THRESHOLD_CONDITION_MET,
+	   "Threshold condition met")
+SENSE_CODE(LOG_COUNTER_AT_MAXIMUM,
+	   "Log counter at maximum")
+SENSE_CODE(LOG_LIST_CODES_EXHAUSTED,
+	   "Log list codes exhausted")
+
+SENSE_CODE(RPL_STATUS_CHANGE,
+	   "Rpl status change")
+SENSE_CODE(SPINDLES_SYNCHRONIZED,
+	   "Spindles synchronized")
+SENSE_CODE(SPINDLES_NOT_SYNCHRONIZED,
+	   "Spindles not synchronized")
+
+SENSE_CODE(FAILURE_PREDICTION_THRESHOLD_EXCEEDED,
+	   "Failure prediction threshold exceeded")
+SENSE_CODE(MEDIA_FAILURE_PREDICTION_THRESHOLD_EXCEEDED,
+	   "Media failure prediction threshold exceeded")
+SENSE_CODE(LU_FAILURE_PREDICTION_THRESHOLD_EXCEEDED,
+	   "Logical unit failure prediction threshold exceeded")
+SENSE_CODE(SPARE_AREA_EXHAUSTION_PREDICTION_THRESHOLD_EXCEEDED,
+	   "Spare area exhaustion prediction threshold exceeded")
+SENSE_CODE(HW_IMPENDING_FAILURE_GENERAL_HARD_DRIVE_FAILURE,
+	   "Hardware impending failure general hard drive failure")
+SENSE_CODE(HW_IMPENDING_FAILURE_DRIVE_ERROR_RATE_TOO_HIGH,
+	   "Hardware impending failure drive error rate too high")
+SENSE_CODE(HW_IMPENDING_FAILURE_DATA_ERROR_RATE_TOO_HIGH,
+	   "Hardware impending failure data error rate too high")
+SENSE_CODE(HW_IMPENDING_FAILURE_SEEK_ERROR_RATE_TOO_HIGH,
+	   "Hardware impending failure seek error rate too high")
+SENSE_CODE(HW_IMPENDING_FAILURE_TOO_MANY_BLOCK_REASSIGNS,
+	   "Hardware impending failure too many block reassigns")
+SENSE_CODE(HW_IMPENDING_FAILURE_ACCESS_TIMES_TOO_HIGH,
+	   "Hardware impending failure access times too high")
+SENSE_CODE(HW_IMPENDING_FAILURE_START_UNIT_TIMES_TOO_HIGH,
+	   "Hardware impending failure start unit times too high")
+SENSE_CODE(HW_IMPENDING_FAILURE_CHANNEL_PARAMETRICS,
+	   "Hardware impending failure channel parametrics")
+SENSE_CODE(HW_IMPENDING_FAILURE_CONTROLLER_DETECTED,
+	   "Hardware impending failure controller detected")
+SENSE_CODE(HW_IMPENDING_FAILURE_THROUGHPUT_PERFORMANCE,
+	   "Hardware impending failure throughput performance")
+SENSE_CODE(HW_IMPENDING_FAILURE_SEEK_TIME_PERFORMANCE,
+	   "Hardware impending failure seek time performance")
+SENSE_CODE(HW_IMPENDING_FAILURE_SPINUP_RETRY_COUNT,
+	   "Hardware impending failure spin-up retry count")
+SENSE_CODE(HW_IMPENDING_FAILURE_DRIVE_CALIBRATION_RETRY_COUNT,
+	   "Hardware impending failure drive calibration retry count")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_GENERAL_HARD_DRIVE_FAILURE,
+	   "Controller impending failure general hard drive failure")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_DRIVE_ERROR_RATE_TOO_HIGH,
+	   "Controller impending failure drive error rate too high")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_DATA_ERROR_RATE_TOO_HIGH,
+	   "Controller impending failure data error rate too high")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_SEEK_ERROR_RATE_TOO_HIGH,
+	   "Controller impending failure seek error rate too high")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_TOO_MANY_BLOCK_REASSIGNS,
+	   "Controller impending failure too many block reassigns")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_ACCESS_TIMES_TOO_HIGH,
+	   "Controller impending failure access times too high")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_START_UNIT_TIMES_TOO_HIGH,
+	   "Controller impending failure start unit times too high")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_CHANNEL_PARAMETRICS,
+	   "Controller impending failure channel parametrics")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_CONTROLLER_DETECTED,
+	   "Controller impending failure controller detected")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_THROUGHPUT_PERFORMANCE,
+	   "Controller impending failure throughput performance")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_SEEK_TIME_PERFORMANCE,
+	   "Controller impending failure seek time performance")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_SPINUP_RETRY_COUNT,
+	   "Controller impending failure spin-up retry count")
+SENSE_CODE(CONTROLLER_IMPENDING_FAILURE_DRIVE_CALIBRATION_RETRY_COUNT,
+	   "Controller impending failure drive calibration retry count")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_GENERAL_HARD_DRIVE_FAILURE,
+	   "Data channel impending failure general hard drive failure")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_DRIVE_ERROR_RATE_TOO_HIGH,
+	   "Data channel impending failure drive error rate too high")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_DATA_ERROR_RATE_TOO_HIGH,
+	   "Data channel impending failure data error rate too high")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_SEEK_ERROR_RATE_TOO_HIGH,
+	   "Data channel impending failure seek error rate too high")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_TOO_MANY_BLOCK_REASSIGNS,
+	   "Data channel impending failure too many block reassigns")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_ACCESS_TIMES_TOO_HIGH,
+	   "Data channel impending failure access times too high")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_START_UNIT_TIMES_TOO_HIGH,
+	   "Data channel impending failure start unit times too high")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_CHANNEL_PARAMETRICS,
+	   "Data channel impending failure channel parametrics")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_CONTROLLER_DETECTED,
+	   "Data channel impending failure controller detected")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_THROUGHPUT_PERFORMANCE,
+	   "Data channel impending failure throughput performance")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_SEEK_TIME_PERFORMANCE,
+	   "Data channel impending failure seek time performance")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_SPINUP_RETRY_COUNT,
+	   "Data channel impending failure spin-up retry count")
+SENSE_CODE(DATA_CHANNEL_IMPENDING_FAILURE_DRIVE_CALIBRATION_RETRY_COUNT,
+	   "Data channel impending failure drive calibration retry count")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_GENERAL_HARD_DRIVE_FAILURE,
+	   "Servo impending failure general hard drive failure")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_DRIVE_ERROR_RATE_TOO_HIGH,
+	   "Servo impending failure drive error rate too high")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_DATA_ERROR_RATE_TOO_HIGH,
+	   "Servo impending failure data error rate too high")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_SEEK_ERROR_RATE_TOO_HIGH,
+	   "Servo impending failure seek error rate too high")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_TOO_MANY_BLOCK_REASSIGNS,
+	   "Servo impending failure too many block reassigns")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_ACCESS_TIMES_TOO_HIGH,
+	   "Servo impending failure access times too high")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_START_UNIT_TIMES_TOO_HIGH,
+	   "Servo impending failure start unit times too high")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_CHANNEL_PARAMETRICS,
+	   "Servo impending failure channel parametrics")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_CONTROLLER_DETECTED,
+	   "Servo impending failure controller detected")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_THROUGHPUT_PERFORMANCE,
+	   "Servo impending failure throughput performance")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_SEEK_TIME_PERFORMANCE,
+	   "Servo impending failure seek time performance")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_SPINUP_RETRY_COUNT,
+	   "Servo impending failure spin-up retry count")
+SENSE_CODE(SERVO_IMPENDING_FAILURE_DRIVE_CALIBRATION_RETRY_COUNT,
+	   "Servo impending failure drive calibration retry count")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_GENERAL_HARD_DRIVE_FAILURE,
+	   "Spindle impending failure general hard drive failure")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_DRIVE_ERROR_RATE_TOO_HIGH,
+	   "Spindle impending failure drive error rate too high")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_DATA_ERROR_RATE_TOO_HIGH,
+	   "Spindle impending failure data error rate too high")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_SEEK_ERROR_RATE_TOO_HIGH,
+	   "Spindle impending failure seek error rate too high")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_TOO_MANY_BLOCK_REASSIGNS,
+	   "Spindle impending failure too many block reassigns")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_ACCESS_TIMES_TOO_HIGH,
+	   "Spindle impending failure access times too high")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_START_UNIT_TIMES_TOO_HIGH,
+	   "Spindle impending failure start unit times too high")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_CHANNEL_PARAMETRICS,
+	   "Spindle impending failure channel parametrics")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_CONTROLLER_DETECTED,
+	   "Spindle impending failure controller detected")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_THROUGHPUT_PERFORMANCE,
+	   "Spindle impending failure throughput performance")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_SEEK_TIME_PERFORMANCE,
+	   "Spindle impending failure seek time performance")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_SPINUP_RETRY_COUNT,
+	   "Spindle impending failure spin-up retry count")
+SENSE_CODE(SPINDLE_IMPENDING_FAILURE_DRIVE_CALIBRATION_RETRY_COUNT,
+	   "Spindle impending failure drive calibration retry count")
+SENSE_CODE(FW_IMPENDING_FAILURE_GENERAL_HARD_DRIVE_FAILURE,
+	   "Firmware impending failure general hard drive failure")
+SENSE_CODE(FW_IMPENDING_FAILURE_DRIVE_ERROR_RATE_TOO_HIGH,
+	   "Firmware impending failure drive error rate too high")
+SENSE_CODE(FW_IMPENDING_FAILURE_DATA_ERROR_RATE_TOO_HIGH,
+	   "Firmware impending failure data error rate too high")
+SENSE_CODE(FW_IMPENDING_FAILURE_SEEK_ERROR_RATE_TOO_HIGH,
+	   "Firmware impending failure seek error rate too high")
+SENSE_CODE(FW_IMPENDING_FAILURE_TOO_MANY_BLOCK_REASSIGNS,
+	   "Firmware impending failure too many block reassigns")
+SENSE_CODE(FW_IMPENDING_FAILURE_ACCESS_TIMES_TOO_HIGH,
+	   "Firmware impending failure access times too high")
+SENSE_CODE(FW_IMPENDING_FAILURE_START_UNIT_TIMES_TOO_HIGH,
+	   "Firmware impending failure start unit times too high")
+SENSE_CODE(FW_IMPENDING_FAILURE_CHANNEL_PARAMETRICS,
+	   "Firmware impending failure channel parametrics")
+SENSE_CODE(FW_IMPENDING_FAILURE_CONTROLLER_DETECTED,
+	   "Firmware impending failure controller detected")
+SENSE_CODE(FW_IMPENDING_FAILURE_THROUGHPUT_PERFORMANCE,
+	   "Firmware impending failure throughput performance")
+SENSE_CODE(FW_IMPENDING_FAILURE_SEEK_TIME_PERFORMANCE,
+	   "Firmware impending failure seek time performance")
+SENSE_CODE(FW_IMPENDING_FAILURE_SPINUP_RETRY_COUNT,
+	   "Firmware impending failure spin-up retry count")
+SENSE_CODE(FW_IMPENDING_FAILURE_DRIVE_CALIBRATION_RETRY_COUNT,
+	   "Firmware impending failure drive calibration retry count")
+SENSE_CODE(MEDIA_IMPENDING_FAILURE_ENDURANCE_LIMIT_MET,
+	   "Media impending failure endurance limit met")
+SENSE_CODE(FAILURE_PREDICTION_THRESHOLD_EXCEEDED_FALSE,
+	   "Failure prediction threshold exceeded (false)")
+
+SENSE_CODE(LOW_POWER_CONDITION_ON,
+	   "Low power condition on")
+SENSE_CODE(IDLE_CONDITION_ACTIVATED_BY_TIMER,
+	   "Idle condition activated by timer")
+SENSE_CODE(STANDBY_CONDITION_ACTIVATED_BY_TIMER,
+	   "Standby condition activated by timer")
+SENSE_CODE(IDLE_CONDITION_ACTIVATED_BY_COMMAND,
+	   "Idle condition activated by command")
+SENSE_CODE(STANDBY_CONDITION_ACTIVATED_BY_COMMAND,
+	   "Standby condition activated by command")
+SENSE_CODE(IDLE_B_CONDITION_ACTIVATED_BY_TIMER,
+	   "Idle_b condition activated by timer")
+SENSE_CODE(IDLE_B_CONDITION_ACTIVATED_BY_COMMAND,
+	   "Idle_b condition activated by command")
+SENSE_CODE(IDLE_C_CONDITION_ACTIVATED_BY_TIMER,
+	   "Idle_c condition activated by timer")
+SENSE_CODE(IDLE_C_CONDITION_ACTIVATED_BY_COMMAND,
+	   "Idle_c condition activated by command")
+SENSE_CODE(STANDBY_Y_CONDITION_ACTIVATED_BY_TIMER,
+	   "Standby_y condition activated by timer")
+SENSE_CODE(STANDBY_Y_CONDITION_ACTIVATED_BY_COMMAND,
+	   "Standby_y condition activated by command")
+SENSE_CODE(POWER_STATE_CHANGE_TO_ACTIVE,
+	   "Power state change to active")
+SENSE_CODE(POWER_STATE_CHANGE_TO_IDLE,
+	   "Power state change to idle")
+SENSE_CODE(POWER_STATE_CHANGE_TO_STANDBY,
+	   "Power state change to standby")
+SENSE_CODE(POWER_STATE_CHANGE_TO_SLEEP,
+	   "Power state change to sleep")
+SENSE_CODE(POWER_STATE_CHANGE_TO_DEVICE_CONTROL,
+	   "Power state change to device control")
+
+SENSE_CODE(LAMP_FAILURE,
+	   "Lamp failure")
+
+SENSE_CODE(VIDEO_ACQUISITION_ERROR,
+	   "Video acquisition error")
+SENSE_CODE(UNABLE_TO_ACQUIRE_VIDEO,
+	   "Unable to acquire video")
+SENSE_CODE(OUT_OF_FOCUS,
+	   "Out of focus")
+
+SENSE_CODE(SCAN_HEAD_POSITIONING_ERROR,
+	   "Scan head positioning error")
+
+SENSE_CODE(END_OF_USER_AREA_ENCOUNTERED_ON_THIS_TRACK,
+	   "End of user area encountered on this track")
+SENSE_CODE(PACKET_DOES_NOT_FIT_IN_AVAILABLE_SPACE,
+	   "Packet does not fit in available space")
+
+SENSE_CODE(ILLEGAL_MODE_FOR_THIS_TRACK,
+	   "Illegal mode for this track")
+SENSE_CODE(INVALID_PACKET_SIZE,
+	   "Invalid packet size")
+
+SENSE_CODE(VOLTAGE_FAULT,
+	   "Voltage fault")
+
+SENSE_CODE(AUTOMATIC_DOCUMENT_FEEDER_COVER_UP,
+	   "Automatic document feeder cover up")
+SENSE_CODE(AUTOMATIC_DOCUMENT_FEEDER_LIFT_UP,
+	   "Automatic document feeder lift up")
+SENSE_CODE(DOCUMENT_JAM_IN_AUTOMATIC_DOCUMENT_FEEDER,
+	   "Document jam in automatic document feeder")
+SENSE_CODE(DOCUMENT_MISS_FEED_AUTOMATIC_IN_DOCUMENT_FEEDER,
+	   "Document miss feed automatic in document feeder")
+
+SENSE_CODE(CONFIG_FAILURE,
+	   "Configuration failure")
+SENSE_CODE(CONFIG_OF_INCAPABLE_LOGICAL_UNITS_FAILED,
+	   "Configuration of incapable logical units failed")
+SENSE_CODE(ADD_LU_FAILED,
+	   "Add logical unit failed")
+SENSE_CODE(MODIFICATION_OF_LU_FAILED,
+	   "Modification of logical unit failed")
+SENSE_CODE(EXCHANGE_OF_LU_FAILED,
+	   "Exchange of logical unit failed")
+SENSE_CODE(REMOVE_OF_LU_FAILED,
+	   "Remove of logical unit failed")
+SENSE_CODE(ATTACHMENT_OF_LU_FAILED,
+	   "Attachment of logical unit failed")
+SENSE_CODE(CREATION_OF_LU_FAILED,
+	   "Creation of logical unit failed")
+SENSE_CODE(ASSIGN_FAILURE_OCCURRED,
+	   "Assign failure occurred")
+SENSE_CODE(MULTIPLY_ASSIGNED_LOGICAL_UNIT,
+	   "Multiply assigned logical unit")
+SENSE_CODE(SET_TARGET_PORT_GROUPS_COMMAND_FAILED,
+	   "Set target port groups command failed")
+SENSE_CODE(ATA_DEVICE_FEATURE_NOT_ENABLED,
+	   "ATA device feature not enabled")
+SENSE_CODE(COMMAND_REJECTED,
+	   "Command rejected")
+SENSE_CODE(EXPLICIT_BIND_NOT_ALLOWED,
+	   "Explicit bind not allowed")
+
+SENSE_CODE(LU_NOT_CONFIGURED,
+	   "Logical unit not configured")
+SENSE_CODE(SUBSIDIARY_LU_NOT_CONFIGURED,
+	   "Subsidiary logical unit not configured")
+
+SENSE_CODE(DATA_LOSS_ON_LOGICAL_UNIT,
+	   "Data loss on logical unit")
+SENSE_CODE(MULTIPLE_LU_FAILURES,
+	   "Multiple logical unit failures")
+SENSE_CODE(PARITY_DATA_MISMATCH,
+	   "Parity/data mismatch")
+
+SENSE_CODE(INFORMATIONAL_REFER_TO_LOG,
+	   "Informational, refer to log")
+
+SENSE_CODE(STATE_CHANGE_HAS_OCCURRED,
+	   "State change has occurred")
+SENSE_CODE(REDUNDANCY_LEVEL_GOT_BETTER,
+	   "Redundancy level got better")
+SENSE_CODE(REDUNDANCY_LEVEL_GOT_WORSE,
+	   "Redundancy level got worse")
+
+SENSE_CODE(REBUILD_FAILURE_OCCURRED,
+	   "Rebuild failure occurred")
+
+SENSE_CODE(RECALCULATE_FAILURE_OCCURRED,
+	   "Recalculate failure occurred")
+
+SENSE_CODE(COMMAND_TO_LU_FAILED,
+	   "Command to logical unit failed")
+
+SENSE_CODE(COPY_PROTECTION_KEY_EXCHANGE_FAILURE_AUTHENTICATION_FAILURE,
+	   "Copy protection key exchange failure - authentication failure")
+SENSE_CODE(COPY_PROTECTION_KEY_EXCHANGE_FAILURE_KEY_NOT_PRESENT,
+	   "Copy protection key exchange failure - key not present")
+SENSE_CODE(COPY_PROTECTION_KEY_EXCHANGE_FAILURE_KEY_NOT_ESTABLISHED,
+	   "Copy protection key exchange failure - key not established")
+SENSE_CODE(READ_OF_SCRAMBLED_SECTOR_WITHOUT_AUTHENTICATION,
+	   "Read of scrambled sector without authentication")
+SENSE_CODE(MEDIA_REGION_CODE_IS_MISMATCHED_TO_LU_REGION,
+	   "Media region code is mismatched to logical unit region")
+SENSE_CODE(DRIVE_REGION_MUST_BE_PERMANENT_REGION_RESET_COUNT_ERROR,
+	   "Drive region must be permanent/region reset count error")
+SENSE_CODE(INSUFFICIENT_BLOCK_COUNT_FOR_BINDING_NONCE_RECORDING,
+	   "Insufficient block count for binding nonce recording")
+SENSE_CODE(CONFLICT_IN_BINDING_NONCE_RECORDING,
+	   "Conflict in binding nonce recording")
+SENSE_CODE(INSUFFICIENT_PERMISSION,
+	   "Insufficient permission")
+SENSE_CODE(INVALID_DRIVE_HOST_PAIRING_SERVER,
+	   "Invalid drive-host pairing server")
+SENSE_CODE(DRIVE_HOST_PAIRING_SUSPENDED,
+	   "Drive-host pairing suspended")
 
 /*
- *	SENSE_CODE(0x70NN, "Decompression exception short algorithm id of nn")
+ * SENSE_CODE(0x70NN, "Decompression exception short algorithm id of nn")
  */
-SENSE_CODE(0x7100, "Decompression exception long algorithm id")
-
-SENSE_CODE(0x7200, "Session fixation error")
-SENSE_CODE(0x7201, "Session fixation error writing lead-in")
-SENSE_CODE(0x7202, "Session fixation error writing lead-out")
-SENSE_CODE(0x7203, "Session fixation error - incomplete track in session")
-SENSE_CODE(0x7204, "Empty or partially written reserved track")
-SENSE_CODE(0x7205, "No more track reservations allowed")
-SENSE_CODE(0x7206, "RMZ extension is not allowed")
-SENSE_CODE(0x7207, "No more test zone extensions are allowed")
-
-SENSE_CODE(0x7300, "Cd control error")
-SENSE_CODE(0x7301, "Power calibration area almost full")
-SENSE_CODE(0x7302, "Power calibration area is full")
-SENSE_CODE(0x7303, "Power calibration area error")
-SENSE_CODE(0x7304, "Program memory area update failure")
-SENSE_CODE(0x7305, "Program memory area is full")
-SENSE_CODE(0x7306, "RMA/PMA is almost full")
-SENSE_CODE(0x7310, "Current power calibration area almost full")
-SENSE_CODE(0x7311, "Current power calibration area is full")
-SENSE_CODE(0x7317, "RDZ is full")
-
-SENSE_CODE(0x7400, "Security error")
-SENSE_CODE(0x7401, "Unable to decrypt data")
-SENSE_CODE(0x7402, "Unencrypted data encountered while decrypting")
-SENSE_CODE(0x7403, "Incorrect data encryption key")
-SENSE_CODE(0x7404, "Cryptographic integrity validation failed")
-SENSE_CODE(0x7405, "Error decrypting data")
-SENSE_CODE(0x7406, "Unknown signature verification key")
-SENSE_CODE(0x7407, "Encryption parameters not useable")
-SENSE_CODE(0x7408, "Digital signature validation failure")
-SENSE_CODE(0x7409, "Encryption mode mismatch on read")
-SENSE_CODE(0x740A, "Encrypted block not raw read enabled")
-SENSE_CODE(0x740B, "Incorrect Encryption parameters")
-SENSE_CODE(0x740C, "Unable to decrypt parameter list")
-SENSE_CODE(0x740D, "Encryption algorithm disabled")
-SENSE_CODE(0x7410, "SA creation parameter value invalid")
-SENSE_CODE(0x7411, "SA creation parameter value rejected")
-SENSE_CODE(0x7412, "Invalid SA usage")
-SENSE_CODE(0x7421, "Data Encryption configuration prevented")
-SENSE_CODE(0x7430, "SA creation parameter not supported")
-SENSE_CODE(0x7440, "Authentication failed")
-SENSE_CODE(0x7461, "External data encryption key manager access error")
-SENSE_CODE(0x7462, "External data encryption key manager error")
-SENSE_CODE(0x7463, "External data encryption key not found")
-SENSE_CODE(0x7464, "External data encryption request not authorized")
-SENSE_CODE(0x746E, "External data encryption control timeout")
-SENSE_CODE(0x746F, "External data encryption control error")
-SENSE_CODE(0x7471, "Logical unit access not authorized")
-SENSE_CODE(0x7479, "Security conflict in translated device")
+
+SENSE_CODE(DECOMPRESSION_EXCEPTION_LONG_ALGORITHM_ID,
+	   "Decompression exception long algorithm id")
+
+SENSE_CODE(SESSION_FIXATION_ERROR,
+	   "Session fixation error")
+SENSE_CODE(SESSION_FIXATION_ERROR_WRITING_LEAD_IN,
+	   "Session fixation error writing lead-in")
+SENSE_CODE(SESSION_FIXATION_ERROR_WRITING_LEAD_OUT,
+	   "Session fixation error writing lead-out")
+SENSE_CODE(SESSION_FIXATION_ERROR_INCOMPLETE_TRACK_IN_SESSION,
+	   "Session fixation error - incomplete track in session")
+SENSE_CODE(EMPTY_OR_PARTIALLY_WRITTEN_RESERVED_TRACK,
+	   "Empty or partially written reserved track")
+SENSE_CODE(NO_MORE_TRACK_RESERVATIONS_ALLOWED,
+	   "No more track reservations allowed")
+SENSE_CODE(RMZ_EXTENSION_IS_NOT_ALLOWED,
+	   "RMZ extension is not allowed")
+SENSE_CODE(NO_MORE_TEST_ZONE_EXTENSIONS_ARE_ALLOWED,
+	   "No more test zone extensions are allowed")
+
+SENSE_CODE(CD_CONTROL_ERROR,
+	   "Cd control error")
+SENSE_CODE(POWER_CALIBRATION_AREA_ALMOST_FULL,
+	   "Power calibration area almost full")
+SENSE_CODE(POWER_CALIBRATION_AREA_IS_FULL,
+	   "Power calibration area is full")
+SENSE_CODE(POWER_CALIBRATION_AREA_ERROR,
+	   "Power calibration area error")
+SENSE_CODE(PROGRAM_MEMORY_AREA_UPDATE_FAILURE,
+	   "Program memory area update failure")
+SENSE_CODE(PROGRAM_MEMORY_AREA_IS_FULL,
+	   "Program memory area is full")
+SENSE_CODE(RMA_PMA_IS_ALMOST_FULL,
+	   "RMA/PMA is almost full")
+SENSE_CODE(CURRENT_POWER_CALIBRATION_AREA_ALMOST_FULL,
+	   "Current power calibration area almost full")
+SENSE_CODE(CURRENT_POWER_CALIBRATION_AREA_IS_FULL,
+	   "Current power calibration area is full")
+SENSE_CODE(RDZ_IS_FULL,
+	   "RDZ is full")
+
+SENSE_CODE(SECURITY_ERROR,
+	   "Security error")
+SENSE_CODE(UNABLE_TO_DECRYPT_DATA,
+	   "Unable to decrypt data")
+SENSE_CODE(UNENCRYPTED_DATA_ENCOUNTERED_WHILE_DECRYPTING,
+	   "Unencrypted data encountered while decrypting")
+SENSE_CODE(INCORRECT_DATA_ENCRYPTION_KEY,
+	   "Incorrect data encryption key")
+SENSE_CODE(CRYPTOGRAPHIC_INTEGRITY_VALIDATION_FAILED,
+	   "Cryptographic integrity validation failed")
+SENSE_CODE(ERROR_DECRYPTING_DATA,
+	   "Error decrypting data")
+SENSE_CODE(UNKNOWN_SIGNATURE_VERIFICATION_KEY,
+	   "Unknown signature verification key")
+SENSE_CODE(ENCRYPTION_PARAMS_NOT_USEABLE,
+	   "Encryption parameters not useable")
+SENSE_CODE(DIGITAL_SIGNATURE_VALIDATION_FAILURE,
+	   "Digital signature validation failure")
+SENSE_CODE(ENCRYPTION_MODE_MISMATCH_ON_READ,
+	   "Encryption mode mismatch on read")
+SENSE_CODE(ENCRYPTED_BLOCK_NOT_RAW_READ_ENABLED,
+	   "Encrypted block not raw read enabled")
+SENSE_CODE(INCORRECT_ENCRYPTION_PARAMS,
+	   "Incorrect Encryption parameters")
+SENSE_CODE(UNABLE_TO_DECRYPT_PARAMETER_LIST,
+	   "Unable to decrypt parameter list")
+SENSE_CODE(ENCRYPTION_ALGORITHM_DISABLED,
+	   "Encryption algorithm disabled")
+SENSE_CODE(SA_CREATION_PARAMETER_VALUE_INVALID,
+	   "SA creation parameter value invalid")
+SENSE_CODE(SA_CREATION_PARAMETER_VALUE_REJECTED,
+	   "SA creation parameter value rejected")
+SENSE_CODE(INVALID_SA_USAGE,
+	   "Invalid SA usage")
+SENSE_CODE(DATA_ENCRYPTION_CONFIG_PREVENTED,
+	   "Data Encryption configuration prevented")
+SENSE_CODE(SA_CREATION_PARAMETER_NOT_SUPPORTED,
+	   "SA creation parameter not supported")
+SENSE_CODE(AUTHENTICATION_FAILED,
+	   "Authentication failed")
+SENSE_CODE(EXTERNAL_DATA_ENCRYPTION_KEY_MANAGER_ACCESS_ERROR,
+	   "External data encryption key manager access error")
+SENSE_CODE(EXTERNAL_DATA_ENCRYPTION_KEY_MANAGER_ERROR,
+	   "External data encryption key manager error")
+SENSE_CODE(EXTERNAL_DATA_ENCRYPTION_KEY_NOT_FOUND,
+	   "External data encryption key not found")
+SENSE_CODE(EXTERNAL_DATA_ENCRYPTION_REQUEST_NOT_AUTHORIZED,
+	   "External data encryption request not authorized")
+SENSE_CODE(EXTERNAL_DATA_ENCRYPTION_CONTROL_TIMEOUT,
+	   "External data encryption control timeout")
+SENSE_CODE(EXTERNAL_DATA_ENCRYPTION_CONTROL_ERROR,
+	   "External data encryption control error")
+SENSE_CODE(LU_ACCESS_NOT_AUTHORIZED,
+	   "Logical unit access not authorized")
+SENSE_CODE(SECURITY_CONFLICT_IN_TRANSLATED_DEVICE,
+	   "Security conflict in translated device")

index 340785536998..4b97f574fe8c 100644
@@ -292,7 +292,7 @@ bool scsi_opcode_sa_name(int opcode, int service_action,
 }
 
 struct error_info {
-	unsigned short code12;	/* 0x0302 looks better than 0x03,0x02 */
+	unsigned short code;	/* 0x0302 looks better than 0x03,0x02 */
 	unsigned short size;
 };
 

@@ -318,9 +318,11 @@ static const char *additional_text =
 	;
 
 struct error_info2 {
-	unsigned char code1, code2_min, code2_max;
-	const char * str;
-	const char * fmt;
+	u8		asc;
+	u8		ascq_min;
+	u8		ascq_max;
+	const char	*str;
+	const char	*fmt;
 };
 
 static const struct error_info2 additional2[] =

@@ -377,20 +379,20 @@ EXPORT_SYMBOL(scsi_sense_key_string);
 const char *
 scsi_extd_sense_format(unsigned char asc, unsigned char ascq, const char **fmt)
 {
-	int i;
-	unsigned short code = ((asc << 8) | ascq);
+	u16 code = scsi_sense_code(asc, ascq);
 	unsigned offset = 0;
+	int i;
 
 	*fmt = NULL;
 	for (i = 0; i < ARRAY_SIZE(additional); i++) {
-		if (additional[i].code12 == code)
+		if (additional[i].code == code)
 			return additional_text + offset;
 		offset += additional[i].size;
 	}
 	for (i = 0; additional2[i].fmt; i++) {
-		if (additional2[i].code1 == asc &&
-		    ascq >= additional2[i].code2_min &&
-		    ascq <= additional2[i].code2_max) {
+		if (additional2[i].asc == asc &&
+		    ascq >= additional2[i].ascq_min &&
+		    ascq <= additional2[i].ascq_max) {
 			*fmt = additional2[i].fmt;
 			return additional2[i].str;
 		}

index 4010fdbf813c..b804291a36ff 100644
@@ -191,7 +191,7 @@ ch_do_scsi(scsi_changer *ch, unsigned char *cmd, int cmd_len,
 	struct scsi_sense_hdr sshdr;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = 3,

index 6e8849d7f0a3..3431e1ce95fd 100644
@@ -84,7 +84,7 @@ static int hp_sw_tur(struct scsi_device *sdev, struct hp_sw_dh_data *h)
 				REQ_FAILFAST_TRANSPORT | REQ_FAILFAST_DRIVER;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = SCMD_FAILURE_NO_LIMIT,

@@ -138,7 +138,7 @@ static int hp_sw_start_stop(struct hp_sw_dh_data *h)
 			 *
 			 * Switch-over in progress, retry.
 			 */
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = 0x04,
 			.ascq = 0x03,
 			.allowed = HP_SW_RETRIES,

index 88c8e36b221e..75c9cc291e38 100644
@@ -514,33 +514,33 @@ static void send_mode_select(struct work_struct *work)
 				REQ_FAILFAST_TRANSPORT | REQ_FAILFAST_DRIVER;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = NO_SENSE,
+			.sense_key = NO_SENSE,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = ABORTED_COMMAND,
+			.sense_key = ABORTED_COMMAND,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* LUN Not Ready and is in the Process of Becoming Ready */
 		{
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = 0x04,
 			.ascq = 0x01,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Command Lock contention */
 		{
-			.sense = ILLEGAL_REQUEST,
+			.sense_key = ILLEGAL_REQUEST,
 			.asc = 0x91,
 			.ascq = 0x36,
 			.allowed = SCMD_FAILURE_NO_LIMIT,

index 48aab0df30b7..64dbbf1d4a0a 100644
@@ -243,13 +243,13 @@ static int scsi_check_passthrough(struct scsi_cmnd *scmd,
 			continue;
 
 		if (status_byte(failure->result) != SAM_STAT_CHECK_CONDITION ||
-		    failure->sense == SCMD_FAILURE_SENSE_ANY)
+		    failure->sense_key == SCMD_FAILURE_SENSE_KEY_ANY)
 			goto maybe_retry;
 
 		if (!scsi_command_normalize_sense(scmd, &sshdr))
 			return 0;
 
-		if (failure->sense != sshdr.sense_key)
+		if (failure->sense_key != sshdr.sense_key)
 			continue;
 
 		if (failure->asc == SCMD_FAILURE_ASC_ANY)

@@ -2372,7 +2372,7 @@ scsi_mode_sense(struct scsi_device *sdev, int dbd, int modepage, int subpage,
 	struct scsi_sense_hdr my_sshdr;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = retries,

index ae8af0e0047a..4558dc853e26 100644
@@ -17,40 +17,40 @@ static void scsi_lib_test_multiple_sense(struct kunit *test)
 {
 	struct scsi_failure multiple_sense_failure_defs[] = {
 		{
-			.sense = DATA_PROTECT,
+			.sense_key = DATA_PROTECT,
 			.asc = 0x1,
 			.ascq = 0x1,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x11,
 			.ascq = 0x0,
 			.allowed = SCSI_LIB_TEST_MAX_ALLOWED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = 0x11,
 			.ascq = 0x22,
 			.allowed = SCSI_LIB_TEST_MAX_ALLOWED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = ABORTED_COMMAND,
+			.sense_key = ABORTED_COMMAND,
 			.asc = 0x11,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = SCSI_LIB_TEST_MAX_ALLOWED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = HARDWARE_ERROR,
+			.sense_key = HARDWARE_ERROR,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.allowed = SCSI_LIB_TEST_MAX_ALLOWED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = ILLEGAL_REQUEST,
+			.sense_key = ILLEGAL_REQUEST,
 			.asc = 0x91,
 			.ascq = 0x36,
 			.allowed = SCSI_LIB_TEST_MAX_ALLOWED,

@@ -116,8 +116,9 @@ static void scsi_lib_test_any_sense(struct kunit *test)
 {
 	struct scsi_failure any_sense_failure_defs[] = {
 		{
-			.result = SCMD_FAILURE_SENSE_ANY,
+			.sense_key = SCMD_FAILURE_SENSE_KEY_ANY,
 			.allowed = SCSI_LIB_TEST_MAX_ALLOWED,
+			.result = SCMD_FAILURE_RESULT_ANY,
 		},
 		{}
 	};

@@ -129,7 +130,7 @@ static void scsi_lib_test_any_sense(struct kunit *test)
 		.sense_buffer = sense,
 	};
 
-	/* Match using SCMD_FAILURE_SENSE_ANY */
+	/* Match using SCMD_FAILURE_SENSE_KEY_ANY */
 	failures.failure_definitions = any_sense_failure_defs;
 	scsi_build_sense(&sc, 0, MEDIUM_ERROR, 0x11, 0x22);
 	KUNIT_EXPECT_EQ(test, -EAGAIN, scsi_check_passthrough(&sc, &failures));

@@ -215,14 +216,14 @@ static void scsi_lib_test_total_allowed(struct kunit *test)
 {
 	struct scsi_failure total_allowed_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Fail all CCs except the UA above */
 		{
-			.sense = SCMD_FAILURE_SENSE_ANY,
+			.sense_key = SCMD_FAILURE_SENSE_KEY_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Retry any other errors not listed above */

@@ -259,12 +260,12 @@ static void scsi_lib_test_mixed_total(struct kunit *test)
 {
 	struct scsi_failure mixed_total_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x28,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},

index 96e4065ae8b5..8fe93962dc87 100644
@@ -658,12 +658,12 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
 		 * so anyway.
 		 */
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x28,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},

@@ -1457,14 +1457,14 @@ static int scsi_report_lun_scan(struct Scsi_Host *shost,
 	struct scsi_device *sdev;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Fail all CCs except the UA above */
 		{
-			.sense = SCMD_FAILURE_SENSE_ANY,
+			.sense_key = SCMD_FAILURE_SENSE_KEY_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Retry any other errors not listed above */

index 3e3da8c2ff26..ec3884a6657f 100644
@@ -112,7 +112,7 @@ static int spi_execute(struct scsi_device *sdev, const void *cmd,
 			REQ_FAILFAST_DRIVER;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = DV_RETRIES,

index a1b21ea14e54..fecb001115ab 100644
@@ -2033,7 +2033,7 @@ static int sd_pr_in_command(struct block_device *bdev, u8 sa,
 	u8 cmd[10] = { PERSISTENT_RESERVE_IN, sa };
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = 5,

@@ -2145,7 +2145,7 @@ static int sd_pr_out_command(struct block_device *bdev, u8 sa, u64 key,
 	struct scsi_sense_hdr sshdr;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = 5,

@@ -2494,13 +2494,13 @@ sd_spinup_disk(struct scsi_disk *sdkp)
 	struct scsi_failure failure_defs[] = {
 		/* Do not retry Medium Not Present */
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x3A,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = 0x3A,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,

@@ -2817,18 +2817,18 @@ static int read_capacity_10(struct scsi_disk *sdkp, struct scsi_device *sdp,
 	struct scsi_failure failure_defs[] = {
 		/* Do not retry Medium Not Present */
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x3A,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = 0x3A,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		 /* Device reset might occur several times so retry a lot */
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.allowed = READ_CAPACITY_RETRIES_ON_RESET,
 			.result = SAM_STAT_CHECK_CONDITION,

@@ -4159,21 +4159,21 @@ static int sd_start_stop_device(struct scsi_disk *sdkp, int start)
 	struct scsi_failure failure_defs[] = {
 		{
 			/* Power on, reset, or bus device reset occurred */
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.ascq = 0,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			/* Power on occurred */
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.ascq = 1,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			/* SCSI bus reset */
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.ascq = 2,
 			.result = SAM_STAT_CHECK_CONDITION,

index 4c348645b04e..454886c24570 100644
@@ -88,14 +88,14 @@ static int ses_recv_diag(struct scsi_device *sdev, int page_code,
 	unsigned char recv_page_code;
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = SES_RETRIES,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = SES_RETRIES,

@@ -145,14 +145,14 @@ static int ses_send_diag(struct scsi_device *sdev, int page_code,
 	};
 	struct scsi_failure failure_defs[] = {
 		{
-			.sense = UNIT_ATTENTION,
+			.sense_key = UNIT_ATTENTION,
 			.asc = 0x29,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = SES_RETRIES,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
-			.sense = NOT_READY,
+			.sense_key = NOT_READY,
 			.asc = SCMD_FAILURE_ASC_ANY,
 			.ascq = SCMD_FAILURE_ASCQ_ANY,
 			.allowed = SES_RETRIES,

index 8694eeadd753..e321471e8ca2 100644
@@ -514,18 +514,18 @@ extern void scsi_sanitize_inquiry_string(unsigned char *s, int len);
  */
 #define SCMD_FAILURE_STAT_ANY	0xff
 /*
- * The following can be set to the scsi_failure sense, asc and ascq fields to
- * match on any sense, ASC, or ASCQ value.
+ * The following can be set to the scsi_failure sense key, asc and ascq fields
+ * to match any sense key, ASC, and ASCQ value.
  */
-#define SCMD_FAILURE_SENSE_ANY	0xff
-#define SCMD_FAILURE_ASC_ANY	0xff
-#define SCMD_FAILURE_ASCQ_ANY	0xff
+#define SCMD_FAILURE_SENSE_KEY_ANY	0xff
+#define SCMD_FAILURE_ASC_ANY		0xff
+#define SCMD_FAILURE_ASCQ_ANY		0xff
 /* Always retry a matching failure. */
 #define SCMD_FAILURE_NO_LIMIT	-1
 
 struct scsi_failure {
 	int result;
-	u8 sense;
+	u8 sense_key;
 	u8 asc;
 	u8 ascq;
 	/*

index 8ecfb94049db..bf6d69f0249f 100644
@@ -394,6 +394,13 @@ static inline unsigned scsi_transfer_length(struct scsi_cmnd *scmd)
 extern void scsi_build_sense(struct scsi_cmnd *scmd, int desc,
 			     u8 key, u8 asc, u8 ascq);
 
+static inline void scsi_set_sense(struct scsi_cmnd *scmd, int desc,
+				  u8 key, u16 code)
+{
+	scsi_build_sense(scmd, desc, key, scsi_sense_code_asc(code),
+			 scsi_sense_code_ascq(code));
+}
+
 struct request *scsi_alloc_request(struct request_queue *q, blk_opf_t opf,
 				   blk_mq_req_flags_t flags);
 

index 00c8a16d3cd2..6fb2c290ba33 100644
@@ -71,8 +71,18 @@ extern u64 scsilun_to_int(struct scsi_lun *);
 struct scsi_sense_hdr {		/* See SPC-3 section 4.5 */
 	u8 response_code;	/* permit: 0x0, 0x70, 0x71, 0x72, 0x73 */
 	u8 sense_key;
-	u8 asc;
-	u8 ascq;
+	union {
+		struct {
+#if defined(__BIG_ENDIAN)
+			u8 asc;
+			u8 ascq;
+#elif defined(__LITTLE_ENDIAN)
+			u8 ascq;
+			u8 asc;
+#endif
+		};
+		u16 sense_code;
+	};
 	u8 byte4;
 	u8 byte5;
 	u8 byte6;

@@ -87,10 +97,27 @@ static inline bool scsi_sense_valid(const struct scsi_sense_hdr *sshdr)
 	return (sshdr->response_code & 0x70) == 0x70;
 }
 
+static inline u8 scsi_sense_asc(const struct scsi_sense_hdr *sshdr)
+{
+	return scsi_sense_code_asc(sshdr->sense_code);
+}
+
+static inline u8 scsi_sense_ascq(const struct scsi_sense_hdr *sshdr)
+{
+	return scsi_sense_code_ascq(sshdr->sense_code);
+}
+
 extern bool scsi_normalize_sense(const u8 *sense_buffer, int sb_len,
 				 struct scsi_sense_hdr *sshdr);
 
 extern void scsi_build_sense_buffer(int desc, u8 *buf, u8 key, u8 asc, u8 ascq);
+
+static inline void scsi_set_sense_buffer(int desc, u8 *buf, u8 key, u16 code)
+{
+	scsi_build_sense_buffer(desc, buf, key, scsi_sense_code_asc(code),
+				scsi_sense_code_ascq(code));
+}
+
 int scsi_set_sense_information(u8 *buf, int buf_len, u64 info);
 int scsi_set_sense_field_pointer(u8 *buf, int buf_len, u16 fp, u8 bp, bool cd);
 extern const u8 * scsi_sense_desc_find(const u8 * sense_buffer, int sb_len,

index e321471e8ca2..11910142ac50 100644
@@ -518,6 +518,7 @@ extern void scsi_sanitize_inquiry_string(unsigned char *s, int len);
  * to match any sense key, ASC, and ASCQ value.
  */
 #define SCMD_FAILURE_SENSE_KEY_ANY	0xff
+#define SCMD_FAILURE_SENSE_CODE_ANY	0xffff
 #define SCMD_FAILURE_ASC_ANY		0xff
 #define SCMD_FAILURE_ASCQ_ANY		0xff
 /* Always retry a matching failure. */

@@ -526,8 +527,18 @@ extern void scsi_sanitize_inquiry_string(unsigned char *s, int len);
 struct scsi_failure {
 	int result;
 	u8 sense_key;
-	u8 asc;
-	u8 ascq;
+	union {
+		struct {
+#if defined(__BIG_ENDIAN)
+			u8 asc;
+			u8 ascq;
+#elif defined(__LITTLE_ENDIAN)
+			u8 ascq;
+			u8 asc;
+#endif
+		};
+		u16 sense_code;
+	};
 	/*
 	 * Number of times scsi_execute_cmd will retry the failure. It does
 	 * not count for the total_allowed.

@@ -537,6 +548,16 @@ struct scsi_failure {
 	s8 retries;
 };
 
+static inline u8 scsi_failure_asc(const struct scsi_failure *failure)
+{
+	return scsi_sense_code_asc(failure->sense_code);
+}
+
+static inline u8 scsi_failure_ascq(const struct scsi_failure *failure)
+{
+	return scsi_sense_code_ascq(failure->sense_code);
+}
+
 struct scsi_failures {
 	/*
 	 * If a scsi_failure does not have a retry limit setup this limit will

index 4b97f574fe8c..57b51c4529c3 100644
@@ -377,22 +377,21 @@ EXPORT_SYMBOL(scsi_sense_key_string);
  * This string may contain a "%x" and should be printed with ascq as arg.
  */
 const char *
-scsi_extd_sense_format(unsigned char asc, unsigned char ascq, const char **fmt)
+scsi_extd_sense_format(const struct scsi_sense_hdr *sshdr, const char **fmt)
 {
-	u16 code = scsi_sense_code(asc, ascq);
 	unsigned offset = 0;
 	int i;
 
 	*fmt = NULL;
 	for (i = 0; i < ARRAY_SIZE(additional); i++) {
-		if (additional[i].code == code)
+		if (additional[i].code == sshdr->sense_code)
 			return additional_text + offset;
 		offset += additional[i].size;
 	}
 	for (i = 0; additional2[i].fmt; i++) {
-		if (additional2[i].asc == asc &&
-		    ascq >= additional2[i].ascq_min &&
-		    ascq <= additional2[i].ascq_max) {
+		if (additional2[i].asc == scsi_sense_asc(sshdr) &&
+		    scsi_sense_ascq(sshdr) >= additional2[i].ascq_min &&
+		    scsi_sense_ascq(sshdr) <= additional2[i].ascq_max) {
 			*fmt = additional2[i].fmt;
 			return additional2[i].str;
 		}

index 3cd0d3074085..0a9a2f7c1966 100644
@@ -238,29 +238,32 @@ EXPORT_SYMBOL(scsi_print_command);
 
 static size_t
 scsi_format_extd_sense(char *buffer, size_t buf_len,
-		       unsigned char asc, unsigned char ascq)
+		       const struct scsi_sense_hdr *sshdr)
 {
 	size_t off = 0;
 	const char *extd_sense_fmt = NULL;
-	const char *extd_sense_str = scsi_extd_sense_format(asc, ascq,
-							    &extd_sense_fmt);
+	const char *extd_sense_str =
+		scsi_extd_sense_format(sshdr, &extd_sense_fmt);
 
 	if (extd_sense_str) {
 		off = scnprintf(buffer, buf_len, "Add. Sense: %s",
 				extd_sense_str);
 		if (extd_sense_fmt)
 			off += scnprintf(buffer + off, buf_len - off,
-					 "(%s%x)", extd_sense_fmt, ascq);
+					 "(%s%x)", extd_sense_fmt,
+					 scsi_sense_ascq(sshdr));
 	} else {
-		if (asc >= 0x80)
+		if (scsi_sense_asc(sshdr) >= 0x80)
 			off = scnprintf(buffer, buf_len, "<<vendor>>");
 		off += scnprintf(buffer + off, buf_len - off,
-				 "ASC=0x%x ", asc);
-		if (ascq >= 0x80)
+				 "ASC=0x%x ",
+				 scsi_sense_asc(sshdr));
+		if (scsi_sense_ascq(sshdr) >= 0x80)
 			off += scnprintf(buffer + off, buf_len - off,
 					 "<<vendor>>");
 		off += scnprintf(buffer + off, buf_len - off,
-				 "ASCQ=0x%x ", ascq);
+				 "ASCQ=0x%x ",
+				 scsi_sense_ascq(sshdr));
 	}
 	return off;
 }

@@ -333,8 +336,7 @@ scsi_log_print_sense_hdr(const struct scsi_device *sdev, const char *name,
 	if (!logbuf)
 		return;
 	off = sdev_format_header(logbuf, logbuf_len, name, tag);
-	off += scsi_format_extd_sense(logbuf + off, logbuf_len - off,
-				      sshdr->asc, sshdr->ascq);
+	off += scsi_format_extd_sense(logbuf + off, logbuf_len - off, sshdr);
 	dev_printk(KERN_INFO, &sdev->sdev_gendev, "%s", logbuf);
 	scsi_log_release_buffer(logbuf);
 }

index dda610f689b7..71923cf28536 100644
@@ -141,14 +141,12 @@ void usb_stor_show_command(const struct us_data *us, struct scsi_cmnd *srb)
 }
 
 void usb_stor_show_sense(const struct us_data *us,
-			 unsigned char key,
-			 unsigned char asc,
-			 unsigned char ascq)
+			 const struct scsi_sense_hdr *sshdr)
 {
 	const char *what, *keystr, *fmt;
 
-	keystr = scsi_sense_key_string(key);
-	what = scsi_extd_sense_format(asc, ascq, &fmt);
+	keystr = scsi_sense_key_string(sshdr->sense_key);
+	what = scsi_extd_sense_format(sshdr, &fmt);
 
 	if (keystr == NULL)
 		keystr = "(Unknown Key)";

@@ -156,7 +154,8 @@ void usb_stor_show_sense(const struct us_data *us,
 		what = "(unknown ASC/ASCQ)";
 
 	if (fmt)
-		usb_stor_dbg(us, "%s: %s (%s%x)\n", keystr, what, fmt, ascq);
+		usb_stor_dbg(us, "%s: %s (%s%x)\n", keystr, what, fmt,
+			     scsi_sense_ascq(sshdr));
 	else
 		usb_stor_dbg(us, "%s: %s\n", keystr, what);
 }

index a6505ceb6693..34e20fff13b5 100644
@@ -31,8 +31,8 @@
 
 #ifdef CONFIG_USB_STORAGE_DEBUG
 void usb_stor_show_command(const struct us_data *us, struct scsi_cmnd *srb);
-void usb_stor_show_sense(const struct us_data *us, unsigned char key,
-			 unsigned char asc, unsigned char ascq);
+void usb_stor_show_sense(const struct us_data *us,
+			 const struct scsi_sense_hdr *sshdr);
 __printf(2, 3) void usb_stor_dbg(const struct us_data *us,
 				 const char *fmt, ...);
 

index 9a4bf86e7b6a..8e9359501d88 100644
@@ -805,7 +805,7 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
 			     sshdr.response_code, sshdr.sense_key,
 			     sshdr.asc, sshdr.ascq);
 #ifdef CONFIG_USB_STORAGE_DEBUG
-		usb_stor_show_sense(us, sshdr.sense_key, sshdr.asc, sshdr.ascq);
+		usb_stor_show_sense(us, &sshdr);
 #endif
 
 		/* set the result so the higher layers expect this data */

index efcdc78530d5..f21a5e3caca9 100644
@@ -20,8 +20,8 @@ extern void scsi_print_result(struct scsi_cmnd *, const char *, int);
 #ifdef CONFIG_SCSI_CONSTANTS
 extern bool scsi_opcode_sa_name(int, int, const char **, const char **);
 extern const char *scsi_sense_key_string(unsigned char);
-extern const char *scsi_extd_sense_format(unsigned char, unsigned char,
-					  const char **);
+extern const char *scsi_extd_sense_format(const struct scsi_sense_hdr *sshdr,
+					  const char **fmt);
 extern const char *scsi_mlreturn_string(int);
 extern const char *scsi_hostbyte_string(int);
 #else

@@ -57,7 +57,7 @@ scsi_sense_key_string(unsigned char key)
 }
 
 static inline const char *
-scsi_extd_sense_format(unsigned char asc, unsigned char ascq, const char **fmt)
+scsi_extd_sense_format(const struct scsi_sense_hdr *sshdr, const char **fmt)
 {
 	*fmt = NULL;
 	return NULL;

index 57b51c4529c3..767631835c81 100644
@@ -327,13 +327,37 @@ struct error_info2 {
 
 static const struct error_info2 additional2[] =
 {
-	{0x40, 0x00, 0x7f, "Ram failure", ""},
-	{0x40, 0x80, 0xff, "Diagnostic failure on component", ""},
-	{0x41, 0x00, 0xff, "Data path failure", ""},
-	{0x42, 0x00, 0xff, "Power-on or self-test failure", ""},
-	{0x4D, 0x00, 0xff, "Tagged overlapped commands", "task tag "},
-	{0x70, 0x00, 0xff, "Decompression exception", "short algorithm id of "},
-	{0, 0, 0, NULL, NULL}
+	{
+		ASC_RAM_FAILURE,
+		0x00, 0x7f,
+		"Ram failure", ""
+	},
+	{
+		ASC_RAM_FAILURE,
+		0x80, 0xff,
+		"Diagnostic failure on component", ""
+	},
+	{
+		ASC_DATA_PATH_FAILURE,
+		0x00, 0xff,
+		"Data path failure", ""
+	},
+	{
+		ASC_POWER_ON_OR_SELFTEST_FAILURE,
+		0x00, 0xff,
+		"Power-on or self-test failure", ""
+	},
+	{
+		ASC_TAGGED_OVERLAPPED_COMMANDS,
+		0x00, 0xff,
+		"Tagged overlapped commands", "task tag "
+	},
+	{
+		ASC_DECOMPRESSION_EXCEPTION_SHORT_ALGORITHM_ID,
+		0x00, 0xff,
+		"Decompression exception", "short algorithm id of "
+	},
+	{ 0, 0, 0, NULL, NULL }
 };
 
 /* description of the sense key values */

index 4e7e7a6b7315..3af9e77847f7 100644
@@ -606,7 +606,8 @@ int scsi_report_opcode(struct scsi_device *sdev, unsigned char *buffer,
 		return result;
 	if (result && scsi_sense_valid(&sshdr) &&
 	    sshdr.sense_key == ILLEGAL_REQUEST &&
-	    (sshdr.asc == 0x20 || sshdr.asc == 0x24) && sshdr.ascq == 0x00)
+	    (sshdr.sense_code == INVALID_COMMAND_OP_CODE ||
+	     sshdr.sense_code == INVALID_FIELD_IN_CDB))
 		return -EINVAL;
 
 	if ((buffer[1] & 3) == 3) /* Command supported */

index e1a2a62b6910..2cabc932acd4 100644
@@ -191,6 +191,8 @@ EXPORT_SYMBOL(int_to_scsilun);
 bool scsi_normalize_sense(const u8 *sense_buffer, int sb_len,
 			  struct scsi_sense_hdr *sshdr)
 {
+	u8 asc = 0, ascq = 0;
+
 	memset(sshdr, 0, sizeof(struct scsi_sense_hdr));
 
 	if (!sense_buffer || !sb_len)

@@ -208,9 +210,9 @@ bool scsi_normalize_sense(const u8 *sense_buffer, int sb_len,
 		if (sb_len > 1)
 			sshdr->sense_key = (sense_buffer[1] & 0xf);
 		if (sb_len > 2)
-			sshdr->asc = sense_buffer[2];
+			asc = sense_buffer[2];
 		if (sb_len > 3)
-			sshdr->ascq = sense_buffer[3];
+			ascq = sense_buffer[3];
 		if (sb_len > 7)
 			sshdr->additional_length = sense_buffer[7];
 	} else {

@@ -222,12 +224,14 @@ bool scsi_normalize_sense(const u8 *sense_buffer, int sb_len,
 		if (sb_len > 7) {
 			sb_len = min(sb_len, sense_buffer[7] + 8);
 			if (sb_len > 12)
-				sshdr->asc = sense_buffer[12];
+				asc = sense_buffer[12];
 			if (sb_len > 13)
-				sshdr->ascq = sense_buffer[13];
+				ascq = sense_buffer[13];
 		}
 	}
 
+	sshdr->sense_code = scsi_sense_code(asc, ascq);
+
 	return true;
 }
 EXPORT_SYMBOL(scsi_normalize_sense);

214 lines not on this page · raw message

index c14f81403a09..122403ec3ab8 100644
@@ -96,7 +96,8 @@ static int ioctl_internal_command(struct scsi_device *sdev, char *cmd,
 					    "ioctl_internal_command: "
 					    "ILLEGAL REQUEST "
 					    "asc=0x%x ascq=0x%x\n",
-					    sshdr.asc, sshdr.ascq);
+					    scsi_sense_asc(&sshdr),
+					    scsi_sense_ascq(&sshdr));
 			break;
 		case NOT_READY:	/* This happens if there is no disc in drive */
 			if (sdev->removable)

182 lines not on this page · raw message

184 lines not on this page · raw message

index 8fe93962dc87..e9ac10cdaac8 100644
@@ -652,19 +652,18 @@ static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result,
 	int pass, count, result, resid;
 	struct scsi_failure failure_defs[] = {
 		/*
-		 * not-ready to ready transition [asc/ascq=0x28/0x0] or
-		 * power-on, reset [asc/ascq=0x29/0x0], continue. INQUIRY
-		 * should not yield UNIT_ATTENTION but many buggy devices do
-		 * so anyway.
+		 * not-ready to ready transition or power-on, reset, continue.
+		 * INQUIRY should not yield UNIT_ATTENTION but many buggy
+		 * devices do so anyway.
 		 */
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x28,
+			.sense_code = NOT_READY_TO_READY_CHANGE_MEDIUM_MAY_HAVE_CHANGED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x29,
+			.sense_code = POWER_ON_RESET_OR_BUS_DEVICE_RESET_OCCURRED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{

@@ -1458,8 +1457,7 @@ static int scsi_report_lun_scan(struct Scsi_Host *shost,
 	struct scsi_failure failure_defs[] = {
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = SCMD_FAILURE_ASC_ANY,
-			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.sense_code = SCMD_FAILURE_SENSE_CODE_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Fail all CCs except the UA above */

index ec3884a6657f..bd049d549244 100644
@@ -113,8 +113,7 @@ static int spi_execute(struct scsi_device *sdev, const void *cmd,
 	struct scsi_failure failure_defs[] = {
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = SCMD_FAILURE_ASC_ANY,
-			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.sense_code = SCMD_FAILURE_SENSE_CODE_ANY,
 			.allowed = DV_RETRIES,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},

@@ -680,10 +679,9 @@ spi_dv_device_echo_buffer(struct scsi_device *sdev, u8 *buffer,
 		if (result || !scsi_device_online(sdev)) {
 
 			scsi_device_set_state(sdev, SDEV_QUIESCE);
-			if (result > 0 && scsi_sense_valid(&sshdr)
-			    && sshdr.sense_key == ILLEGAL_REQUEST
-			    /* INVALID FIELD IN CDB */
-			    && sshdr.asc == 0x24 && sshdr.ascq == 0x00)
+			if (result > 0 && scsi_sense_valid(&sshdr) &&
+			    sshdr.sense_key == ILLEGAL_REQUEST &&
+			    sshdr.sense_code == INVALID_FIELD_IN_CDB)
 				/* This would mean that the drive lied
 				 * to us about supporting an echo
 				 * buffer (unfortunately some Western

index c36c72ab7f2b..e8328df587c3 100644
@@ -303,8 +303,8 @@ DECLARE_EVENT_CLASS(scsi_cmd_done_timeout_template,
 		if (cmd->sense_buffer && SCSI_SENSE_VALID(cmd) &&
 		    scsi_command_normalize_sense(cmd, &sshdr)) {
 			__entry->sense_key = sshdr.sense_key;
-			__entry->asc = sshdr.asc;
-			__entry->ascq = sshdr.ascq;
+			__entry->asc = scsi_sense_asc(&sshdr);
+			__entry->ascq = scsi_sense_ascq(&sshdr);
 		} else {
 			__entry->sense_key = 0;
 			__entry->asc = 0;

index fecb001115ab..b0d2542fd317 100644
@@ -1786,8 +1786,7 @@ static int media_not_present(struct scsi_disk *sdkp,
 	switch (sshdr->sense_key) {
 	case UNIT_ATTENTION:
 	case NOT_READY:
-		/* medium not present */
-		if (sshdr->asc == 0x3A) {
+		if (scsi_sense_asc(sshdr) == ASC_MEDIUM_NOT_PRESENT) {
 			set_media_not_present(sdkp);
 			return 1;
 		}

@@ -1911,12 +1910,14 @@ static int sd_sync_cache(struct scsi_disk *sdkp)
 
 		if (scsi_status_is_check_condition(res) &&
 		    scsi_sense_valid(&sshdr)) {
+			u8 asc = scsi_sense_asc(&sshdr);
+
 			sd_print_sense_hdr(sdkp, &sshdr);
 
 			/* we need to evaluate the error return  */
-			if (sshdr.asc == 0x3a ||	/* medium not present */
-			    sshdr.asc == 0x20 ||	/* invalid command */
-			    (sshdr.asc == 0x74 && sshdr.ascq == 0x71))	/* drive is password locked */
+			if (asc == ASC_MEDIUM_NOT_PRESENT ||
+			    asc == ASC_INVALID_COMMAND_OP_CODE ||
+			    sshdr.sense_code == LU_ACCESS_NOT_AUTHORIZED)
 				/* this is no error here */
 				return 0;
 

@@ -1926,8 +1927,8 @@ static int sd_sync_cache(struct scsi_disk *sdkp)
 			 * this is called during shutdown or suspend so just
 			 * return success so those operations can proceed.
 			 */
-			if ((sshdr.asc == 0x04 && sshdr.ascq == 0x04) ||
-			    sshdr.sense_key == ILLEGAL_REQUEST)
+			if (sshdr.sense_key == ILLEGAL_REQUEST ||
+			    sshdr.sense_code == LU_NOT_READY_FORMAT_IN_PROGRESS)
 				return 0;
 		}
 

@@ -2015,7 +2016,9 @@ static int sd_scsi_to_pr_err(struct scsi_sense_hdr *sshdr, int result)
 			return PR_STS_IOERR;
 
 		if (sshdr->sense_key == ILLEGAL_REQUEST &&
-		    (sshdr->asc == 0x26 || sshdr->asc == 0x24))
+		    (scsi_sense_asc(sshdr) ==
+				ASC_INVALID_FIELD_IN_PARAMETER_LIST ||
+		     scsi_sense_asc(sshdr) == ASC_INVALID_FIELD_IN_CDB))
 			return -EINVAL;
 
 		fallthrough;

@@ -2034,8 +2037,7 @@ static int sd_pr_in_command(struct block_device *bdev, u8 sa,
 	struct scsi_failure failure_defs[] = {
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = SCMD_FAILURE_ASC_ANY,
-			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.sense_code = SCMD_FAILURE_SENSE_CODE_ANY,
 			.allowed = 5,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},

@@ -2146,8 +2148,7 @@ static int sd_pr_out_command(struct block_device *bdev, u8 sa, u64 key,
 	struct scsi_failure failure_defs[] = {
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = SCMD_FAILURE_ASC_ANY,
-			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.sense_code = SCMD_FAILURE_SENSE_CODE_ANY,
 			.allowed = 5,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},

@@ -2440,16 +2441,17 @@ static int sd_done(struct scsi_cmnd *SCpnt)
 		memset(SCpnt->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
 		break;
 	case ABORTED_COMMAND:
-		if (sshdr.asc == 0x10)  /* DIF: Target detected corruption */
+		if (scsi_sense_asc(&sshdr) == ASC_ID_CRC_OR_ECC_ERROR) /* DIF */
 			good_bytes = sd_completed_bytes(SCpnt);
 		break;
 	case ILLEGAL_REQUEST:
-		switch (sshdr.asc) {
-		case 0x10:	/* DIX: Host detected corruption */
+		switch (scsi_sense_asc(&sshdr)) {
+		case ASC_ID_CRC_OR_ECC_ERROR:
+			/* DIX */
 			good_bytes = sd_completed_bytes(SCpnt);
 			break;
-		case 0x20:	/* INVALID COMMAND OPCODE */
-		case 0x24:	/* INVALID FIELD IN CDB */
+		case ASC_INVALID_COMMAND_OP_CODE:
+		case ASC_INVALID_FIELD_IN_CDB:
 			switch (SCpnt->cmnd[0]) {
 			case UNMAP:
 				sd_disable_discard(sdkp);

@@ -2495,14 +2497,14 @@ sd_spinup_disk(struct scsi_disk *sdkp)
 		/* Do not retry Medium Not Present */
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x3A,
-			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.sense_code =
+				MEDIUM_NOT_PRESENT | SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			.sense_key = NOT_READY,
-			.asc = 0x3A,
-			.ascq = SCMD_FAILURE_ASCQ_ANY,
+			.sense_code =
+				MEDIUM_NOT_PRESENT | SCMD_FAILURE_ASCQ_ANY,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		/* Retry when scsi_status_is_good would return false 3 times */

@@ -2566,18 +2568,18 @@ sd_spinup_disk(struct scsi_disk *sdkp)
 			break;
 
 		if (sense_valid && sshdr.sense_key == NOT_READY) {
-			if (sshdr.asc == 4 && sshdr.ascq == 3)
-				break;	/* manual intervention required */
-			if (sshdr.asc == 4 && sshdr.ascq == 0xb)
-				break;	/* standby */
-			if (sshdr.asc == 4 && sshdr.ascq == 0xc)
-				break;	/* unavailable */
-			if (sshdr.asc == 4 && sshdr.ascq == 0x1b)
-				break;	/* sanitize in progress */
-			if (sshdr.asc == 4 && sshdr.ascq == 0x24)
-				break;	/* depopulation in progress */
-			if (sshdr.asc == 4 && sshdr.ascq == 0x25)
-				break;	/* depopulation restoration in progress */
+			switch (sshdr.sense_code) {
+			case LU_NOT_READY_MANUAL_INTERVENTION_REQUIRED:
+			case LU_NOT_ACCESSIBLE_TARGET_PORT_IN_STANDBY_STATE:
+			case LU_NOT_ACCESSIBLE_TARGET_PORT_IN_UNAVAILABLE_STATE:
+			case LU_NOT_READY_SANITIZE_IN_PROGRESS:
+			case DEPOPULATION_IN_PROGRESS:
+			case DEPOPULATION_RESTORATION_IN_PROGRESS:
+				goto out;
+			default:
+				break;
+			}
+
 			/*
 			 * Issue command to spin up drive when not ready
 			 */

@@ -2608,8 +2610,9 @@ sd_spinup_disk(struct scsi_disk *sdkp)
 		 * occur here.  It's characteristic of these devices.
 		 */
 		} else if (sense_valid &&
-				sshdr.sense_key == UNIT_ATTENTION &&
-				sshdr.asc == 0x28) {
+			   sshdr.sense_key == UNIT_ATTENTION &&
+			   scsi_sense_asc(&sshdr) ==
+			   ASC_NOT_READY_TO_READY_CHANGE_MEDIUM_MAY_HAVE_CHANGED) {
 			if (!spintime) {
 				spintime_expire = jiffies + 5 * HZ;
 				spintime = 1;

@@ -2628,6 +2631,7 @@ sd_spinup_disk(struct scsi_disk *sdkp)
 				
 	} while (spintime && time_before_eq(jiffies, spintime_expire));
 
+out:
 	if (spintime) {
 		if (scsi_status_is_good(the_result))
 			printk(KERN_CONT "ready\n");

@@ -2753,15 +2757,14 @@ static int read_capacity_16(struct scsi_disk *sdkp, struct scsi_device *sdp,
 			sense_valid = scsi_sense_valid(&sshdr);
 			if (sense_valid &&
 			    sshdr.sense_key == ILLEGAL_REQUEST &&
-			    (sshdr.asc == 0x20 || sshdr.asc == 0x24) &&
-			    sshdr.ascq == 0x00)
-				/* Invalid Command Operation Code or
-				 * Invalid Field in CDB, just retry
-				 * silently with RC10 */
+			    (sshdr.sense_code == INVALID_COMMAND_OP_CODE ||
+			     sshdr.sense_code == INVALID_FIELD_IN_CDB))
+				/* Just retry silently with RC10 */
 				return -EINVAL;
 			if (sense_valid &&
 			    sshdr.sense_key == UNIT_ATTENTION &&
-			    sshdr.asc == 0x29 && sshdr.ascq == 0x00)
+			    sshdr.sense_code ==
+			    POWER_ON_RESET_OR_BUS_DEVICE_RESET_OCCURRED)
 				/* Device reset might occur several times,
 				 * give it one more chance */
 				if (--reset_retries > 0)

@@ -2818,18 +2821,18 @@ static int read_capacity_10(struct scsi_disk *sdkp, struct scsi_device *sdp,
 		/* Do not retry Medium Not Present */
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x3A,
+			.sense_code = MEDIUM_NOT_PRESENT,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			.sense_key = NOT_READY,
-			.asc = 0x3A,
+			.sense_code = MEDIUM_NOT_PRESENT,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		 /* Device reset might occur several times so retry a lot */
 		{
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x29,
+			.sense_code = POWER_ON_RESET_OR_BUS_DEVICE_RESET_OCCURRED,
 			.allowed = READ_CAPACITY_RETRIES_ON_RESET,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},

@@ -3258,8 +3261,7 @@ sd_read_cache_type(struct scsi_disk *sdkp, unsigned char *buffer)
 bad_sense:
 	if (res == -EIO && scsi_sense_valid(&sshdr) &&
 	    sshdr.sense_key == ILLEGAL_REQUEST &&
-	    sshdr.asc == 0x24 && sshdr.ascq == 0x0)
-		/* Invalid field in CDB */
+	    sshdr.sense_code == INVALID_FIELD_IN_CDB)
 		sd_first_printk(KERN_NOTICE, sdkp, "Cache data unavailable\n");
 	else
 		sd_first_printk(KERN_ERR, sdkp,

@@ -4160,22 +4162,19 @@ static int sd_start_stop_device(struct scsi_disk *sdkp, int start)
 		{
 			/* Power on, reset, or bus device reset occurred */
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x29,
-			.ascq = 0,
+			.sense_code = POWER_ON_RESET_OR_BUS_DEVICE_RESET_OCCURRED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			/* Power on occurred */
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x29,
-			.ascq = 1,
+			.sense_code = POWER_ON_OCCURRED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{
 			/* SCSI bus reset */
 			.sense_key = UNIT_ATTENTION,
-			.asc = 0x29,
-			.ascq = 2,
+			.sense_code = SCSI_BUS_RESET_OCCURRED,
 			.result = SAM_STAT_CHECK_CONDITION,
 		},
 		{}

@@ -4207,8 +4206,7 @@ static int sd_start_stop_device(struct scsi_disk *sdkp, int start)
 		sd_print_result(sdkp, "Start/Stop Unit failed", res);
 		if (res > 0 && scsi_sense_valid(&sshdr)) {
 			sd_print_sense_hdr(sdkp, &sshdr);
-			/* 0x3a is medium not present */
-			if (sshdr.asc == 0x3a)
+			if (scsi_sense_asc(&sshdr) == ASC_MEDIUM_NOT_PRESENT)
 				res = 0;
 		}
 	}

index 56e455fb5add..8b4850cea10f 100644
@@ -369,7 +369,7 @@ unsigned int sd_zbc_complete(struct scsi_cmnd *cmd, unsigned int good_bytes,
 	if (op_is_zone_mgmt(req_op(rq)) &&
 	    result &&
 	    sshdr->sense_key == ILLEGAL_REQUEST &&
-	    sshdr->asc == 0x24) {
+	    scsi_sense_asc(sshdr) == ASC_INVALID_FIELD_IN_CDB) {
 		/*
 		 * INVALID FIELD IN CDB error: a zone management command was
 		 * attempted on a conventional zone. Nothing to worry about,

index c36c54ecd354..4f2e8d1be6da 100644
@@ -253,7 +253,8 @@ static unsigned int sr_check_events(struct cdrom_device_info *cdi,
 	 * (ASC 0x3a).
 	 */
 	cd->media_present = scsi_status_is_good(ret) ||
-		(scsi_sense_valid(&sshdr) && sshdr.asc != 0x3a);
+		(scsi_sense_valid(&sshdr) &&
+		 scsi_sense_asc(&sshdr) != ASC_MEDIUM_NOT_PRESENT);
 
 	if (last_present != cd->media_present)
 		cd->device->changed = 1;

index 089653018d32..e4ec0f63cdcc 100644
@@ -226,9 +226,8 @@ int sr_do_ioctl(Scsi_CD *cd, struct packet_command *cgc)
 			err = -ENOMEDIUM;
 			break;
 		case NOT_READY:	/* This happens if there is no disc in drive */
-			if (sshdr->asc == 0x04 &&
-			    sshdr->ascq == 0x01) {
-				/* sense: Logical unit is in process of becoming ready */
+			if (sshdr->sense_code ==
+			    LU_IS_IN_PROCESS_OF_BECOMING_READY) {
 				if (!cgc->quiet)
 					sr_printk(KERN_INFO, cd,
 						  "CDROM not ready yet.\n");

@@ -250,9 +249,7 @@ int sr_do_ioctl(Scsi_CD *cd, struct packet_command *cgc)
 			break;
 		case ILLEGAL_REQUEST:
 			err = -EIO;
-			if (sshdr->asc == 0x20 &&
-			    sshdr->ascq == 0x00)
-				/* sense: Invalid command operation code */
+			if (sshdr->sense_code == INVALID_COMMAND_OP_CODE)
 				err = -EDRIVE_CANT_DO_THIS;
 			break;
 		default:

@@ -303,9 +300,8 @@ int sr_drive_status(struct cdrom_device_info *cdi, int slot)
 	if (!scsi_test_unit_ready(cd->device, SR_TIMEOUT, MAX_RETRIES, &sshdr))
 		return CDS_DISC_OK;
 
-	/* SK/ASC/ASCQ of 2/4/1 means "unit is becoming ready" */
-	if (scsi_sense_valid(&sshdr) && sshdr.sense_key == NOT_READY
-			&& sshdr.asc == 0x04 && sshdr.ascq == 0x01)
+	if (scsi_sense_valid(&sshdr) && sshdr.sense_key == NOT_READY &&
+	    sshdr.sense_code == LU_IS_IN_PROCESS_OF_BECOMING_READY)
 		return CDS_DRIVE_NOT_READY;
 
 	if (!cdrom_get_media_event(cdi, &med)) {

@@ -318,18 +314,18 @@ int sr_drive_status(struct cdrom_device_info *cdi, int slot)
 	}
 
 	/*
-	 * SK/ASC/ASCQ of 2/4/2 means "initialization required"
 	 * Using CD_TRAY_OPEN results in an START_STOP_UNIT to close
 	 * the tray, which resolves the initialization requirement.
 	 */
-	if (scsi_sense_valid(&sshdr) && sshdr.sense_key == NOT_READY
-			&& sshdr.asc == 0x04 && sshdr.ascq == 0x02)
+	if (scsi_sense_valid(&sshdr) && sshdr.sense_key == NOT_READY &&
+	    sshdr.sense_code == LU_NOT_READY_INITIALIZING_COMMAND_REQUIRED)
 		return CDS_TRAY_OPEN;
 
 	/*
 	 * 0x04 is format in progress .. but there must be a disc present!
 	 */
-	if (sshdr.sense_key == NOT_READY && sshdr.asc == 0x04)
+	if (sshdr.sense_key == NOT_READY &&
+	    scsi_sense_asc(&sshdr) == ASC_LU_NOT_READY)
 		return CDS_DISC_OK;
 
 	/*