Difference in dot clock between xserver 1.5.2 and 1.9.4 - intel driver
Dear All
I have ONE laptop with ONE hdd and 2 OS - opensuse and fedora on it. When I boot opensuse LCD picture is perfect but is not on fedora. My video is i915GM.
I would like to show one difference in xorg log:
X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: openSUSE SUSE LINUX
Current Operating System: Linux linux-xmc2 2.6.27.45-0.1-pae #1 SMP 2010-02-22 16:49:47 +0100 i686
...
(II) intel(0): using SSC reference clock of 96 MHz
************************************************************
X.Org X Server 1.9.4
Release Date: 2011-02-04
[ 22.536] X Protocol Version 11, Revision 0 [ 22.536] Build Operating System: x86-06 2.6.32-71.14.1.el6.x86_64 [ 22.536] Current Operating System: Linux f14.fedora14 2.6.35.11-83.fc14.i686.PAE #1 SMP Mon Feb 7 06:57:55 UTC 2011 i686 ... [ 135.556] (II) intel(0): Supported detailed timing: [ 135.556] (II) intel(0): clock: 65.0 MHz Image Size: 304 x 228 mm
**************************************************************
On OpenSuse, where I can use clock is 96 MHZ, on Fedora it is 65 MHz. Why?
And in MHz can be only dot clock, but if I use 1024x768x60Hz = ~ 47.2 MHz and we need to multiply on 3 (subpixels), it will be ~140 MHz I know that 96 in xserver 1.5.2 is not 140 but it is much closer to it, then 65.
Why in xserver 1.5.2 intel driver shows 96 MHz but in 1.9.4 it does only 65 MHz. And can it be the reason why my LCD shows picture like it use less then 50Hz vsync.
Thank you.
Quoted 1 line · SD
(II) intel(0): using SSC reference clock of 96 MHz
That's the spread-spectrum clock reference value; it forms the basis From which the actual dot clock is computed using a PLL. It is *not* the actual dot clock.
Quoted 2 lines
[ 135.556] (II) intel(0): clock: 65.0 MHz Image Size: 304 x 228mm
And there's the actual dot clock.
Quoted 3 lines
And in MHz can be only dot clock, but if I use 1024x768x60Hz = ~ 47.2 MHz and we need to multiply on 3 (subpixels), it will be ~140 MHz I know that 96 in xserver 1.5.2 is not 140 but it is much closer to
it, then 65.
You don't multiply by three; each channel has it's own wire in LVDS. But, you have to add space for the retrace intervals. The standard VESA mode for 1024x768x60 uses a 65MHz dot clock.
Quoted 3 lines
Why in xserver 1.5.2 intel driver shows 96 MHz but in 1.9.4 it does only 65 MHz. And can it be the reason why my LCD shows picture like it use less then 50Hz vsync.
I'll bet both are using the same timings, but you can check for yourself with the 'xrandr' utility:
$ xrandr --verbose
...
1440x900 (0x45) 74.1MHz -HSync -VSync *current +preferred
h: width 1440 start 1464 end 1480 total 1600 skew 0 clock 46.3KHz
v: height 900 start 903 end 909 total 926 clock 50.0Hz
...The mode marked '*current' is what the system is currently using.
You can help figure out what the problem is by running the 'intel_reg_dumper' utility on both distributions. That's available from:
git://anongit.freedesktop.org/git/xorg/app/intel-gpu-tools
Doing a 'diff' on the output of this under the two operating systems will show every change in programming for your machine.
Signature · 1 line
[email protected]
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx