Skip to content

PPC64-HWBKPT: Hardware Breakpoint interfaces - ver VIII

K.Prasad linuxppc-dev 1 version In review

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest0 of 6 patches 4 repliesIn review

Patches in v1 No applies recorded yet

None of the 6 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [Patch 0/6] [Patch 0/6] PPC64-HWBKPT: Hardware Breakpoint interfaces - ver VIII

Hi David,
I'm back with a new version of patches after a brief hiatus!

After much deliberation about modifying the code to change the timing of signal delivery to user-space, it has been decided to retain the existing behaviour i.e. SIGTRAP delivered to user-space after execution of causative instruction although exception is raised before execution of it.

One-shot behaviour will now be restricted only to ptrace requests. Kernel-space and non-ptrace user-space requests will result in persistent breakpoints.

Reasons
--------
- Signal delivery before execution of instruction requires complex workarounds
- One of the plausible workarounds is a two-pass hw-breakpoint handler which delivers the signal after the first pass (with the breakpoints enabled). In the second pass, it follows the existing semantics of disable_hbp-->enable_ss-->single_step-->disable_ss-->enable_hbp.
- Possibility of nested exceptions is a problem here.
- Proper identification of a second-pass of first exception and a new nested exception is difficult. Possibility of stray exceptions due to accesses in neighbouring memory regions of the breakpoint address further complicates it.
- Alternatives are i)use one-shot for all user-space requests ii)disable signal delivery for non-ptrace requests, allow the user-defined callback routine to generate signal.
- Using one-shot for all user-space requests will break the register/unregister interface semantics.
- Disabling signal delivery for non-ptrace requests is one of the options but will be a digression from x86 behaviour, or would require changes in x86 code too. Even user-defined callback routines cannot deliver signal before instruction execution.

Considering all the above, we propose a behaviour that delivers the signal to user-space after breakpoint execution. In due course, it will be good to have ptrace on PPC64 follow the same behaviour.

Changelog - ver VIII
-------------------
- Reverting changes to allow one-shot breakpoints only for ptrace requests.
- Minor changes in sanity checking in arch_validate_hwbkpt_settings().
- put_cpu_no_resched() is no longer available. Converted to put_cpu().

Thanks,
K.Prasad

Previous changelogs
-------------------
Changelog - ver VII
-------------------
- Allow the one-shot behaviour for exception handlers to be defined by the user. A new 'is_one_shot' flag is added to 'struct arch_hw_breakpoint'.

Changelog - ver VI
------------------
The task of identifying 'genuine' breakpoint exceptions from those caused by 'out-of-range' accesses turned out to be more tricky than originally thought. Some changes to this effect were made in version IV of this patchset, but they were not sufficient for user-space. Basically the breakpoint address received through ptrace is always aligned to 8-bytes since ptrace receives an encoded 'data' (consisting of address | translation_enable | bkpt_type), and the size of the symbol is not known. However for kernel-space addresses, the symbol-size can be determined using kallsyms_lookup_size_offset() and this is used to check if DAR (in the exception context) is
'bkpt_address <= DAR <= (bkpt_address + symbol_size)', failing which we conclude it as a stray exception.

The following changes are made to enable check:
- Addition of a symbolsize field in 'struct arch_hw_breakpoint' field.
- Store the size of the 'watched' kernel symbol into 'symbolsize' field in arch_store_info(0 routine.
- Verify if the above described condition is true when is_one_shot is FALSE in hw_breakpoint_handler().

Changelog - ver V
------------------
- Breakpoint requests from ptrace (for user-space) are designed to be one-shot in PPC64. The patch contains changes to retain this behaviour by returning early in hw_breakpoint_handler() [without re-initialising DABR] and unregistering the user-space request in ptrace_triggered(). It is safe to make a unregister_user_hw_breakpoint() call from the breakpoint exception context [through ptrace_triggered()] without giving rise to circular locking-dependancy. This is because there can be no kernel code running on the CPU (which received the exception) with the same spinlock held.

- Minor change in 'type' member of 'struct arch_hw_breakpoint' from u8 to 'int'.

Changelog - ver IV
------------------
- While DABR register requires double-word (8 bytes) aligned addresses, i.e. the breakpoint is active over a range of 8 bytes, PPC64 allows byte-level addressability. This may lead to stray exceptions which have to be ignored in hw_breakpoint_handler(), when DAR != (Breakpoint request address). However DABR will be populated with the requested breakpoint address aligned to the previous double-word address. The code is now modified to store user-requested address in 'bp->info.address' but update the DABR with a double-word aligned address.
- Please note that the Data Breakpoint facility in Xmon is broken as of 2.6.29 and the same has not been integrated into this facility as described in Ver I.

Changelog - ver III
------------------
- Patches are based on commit 08f16e060bf54bdc34f800ed8b5362cdeda75d8b of -tip tree.
- The declarations in arch/powerpc/include/asm/hw_breakpoint.h are done only if CONFIG_PPC64 is defined. This eliminates the need to conditionally include this header file.
- load_debug_registers() is done in start_secondary() i.e. during CPU initialisation.
- arch_check_va_<> routines in hw_breakpoint.c are now replaced with a much simpler is_kernel_addr() check in arch_validate_hwbkpt_settings()
- Return code of hw_breakpoint_handler() when triggered due to Lazy debug register switching is now changed to NOTIFY_STOP.
- The ptrace code no longer sets the TIF_DEBUG task flag as it is proposed to be done in register_user_hw_breakpoint() routine.
- hw_breakpoint_handler() is now modified to use hbp_kernel_pos value to determine if the trigger was a user/kernel space address. The DAR register value is checked with the address stored in 'struct hw_breakpoint' to avoid handling of exceptions that belong to kprobe/Xmon.

Changelog - ver II
------------------
- Split the monolithic patch into six logical patches
- Changed the signature of arch_check_va_in_<user><kernel>space functions. They are now marked static.
- HB_NUM is now called as HBP_NUM (to preserve a consistent short-name convention)
- Introduced hw_breakpoint_disable() and changes to kexec code to disable breakpoints before a reboot.
- Minor changes in ptrace code to use macro-defined constants instead of numbers.
- Introduced a new constant definition INSTRUCTION_LEN in reg.h